Search Documents

By A. F. Colombo

The differences in starch demands that occur between ore types subjected to the anionic flotation of calcium-activated gangue and the range of residual starch contents expected to give the best metallurgical response were evaluated on a batch and pilot plant basis. A phenol-sulfuric acid procedure was used to determine the residual starch contents in the iron ore slurries. Three pilot plant campaigns on samples from a group of orebodies located on the Marquette Range, Michigan, showed that in the rougher flotation pulp, a residual carbohydrate range of 25 to 100 ppm, which is equivalent to a 0.5 lb/short ton spread, yielded optimum results. Concentrates assaying at least 65 percent Fe and less than 6.0 percent Si02 and containing more than 80 per-cent of the recoverable iron were obtained. Both batch and continuous research indicated that starch adsorption is calcium modulated and relatively unaffected by the fatty acid additions employed. Residual starch level is not a critical control factor, but the addition must be adjusted to about 25 to 50 ppm residual starch and kept in this range for most effective utilization of the added tapioca flour.

Jan 1, 1972

By Martin H. Stanczyk

Ultrafine grinding of the industrial minerals mica, pyrophyllite, talc, marble, barite, and fluorite was accomplished using the Bureau-developed and patented attrition-grinding process. The materials, representing minerals of diverse physical characteristics, were batch ground in a 10-inch-diameter machine using statistically designed experimental test programs. The tests were made to determine large effects of variables such as feed pulp density, grinding medium size, and quantity of the electrical energy consumed during grinding on product particle size and bulk density. In designing the test programs, it was assumed that there was no interaction between the variables. Relatively coarse commercial flotation concentrates of mica, barite, and fluorspar and mine-run products of pyrophyllite, talc, and marble were readily ground into subsieve size ranges. Considering the great amount of particle size reduction obtained, the electrical energy requirements for grinding were very low. In general, the test results indicated that the best conditions for particle size reduction were approached when grinding with the coarser fraction of sand grinding media, the higher-sand-to-mineral weight ratio, and the higher feed pulp density.

Jan 1, 1972

By L. A. Haas

S02 reduction with CO was studied in an integral flow reactor at a nominal flow of 0.5 liter per minute. Reactant gas contained 3 percent SO2, 6 percent CO, and the balance He. SO2 conversion was determined for three different types of catalysts. The first consisted of 16 commercial catalysts used for various chemical syntheses. Only the commercial catalysts which contained transition metals in alumina removed more than 30 percent 80a at temperatures below 510° C. Two other types of catalysts were prepared in the laboratory either by pelletizing equal amounts of powdered alumina and transition metal oxides or by impregnating commercial alumina tablets with transition metal ions. Regardless of preparation techniques, Cr and Fe in alumina were the two best catalysts. The observed results suggest that an intermediate (SCO) is formed by the interaction of surface metal sulfides and carbonyls. Alumina then catalyzes the interaction of SCO with S02 to form the end products (sulfur and carbon dioxide). Over 80 percent S02 was removed at 460° C with 2 grams alumina impregnated with 2.5 percent iron.

Jan 1, 1972

By John P. Gooch

The solubility of 1,1,2,2-tetrabromoethane (TBE) in water was determined from 1.0° to 97.0° C. The solubility (S) of TBE in grams of solute per 100 grams water was correlated with [S = 1,920.55 [exp (40292L7 11, T2 10 T 737.577 + 9.923962 ] where T is in degrees Kelvin. A thermodynamic analysis conducted on a system consisting of a TBE phase and a water phase in equilibrium with a vapor phase led to the calculation of the activity coefficient, vapor-liquid equilibrium distribution coefficient, relative volatility, and heat of mixing for saturated solutions of TBE in water. Data required for these calculations were the solubility of TBE in water and the vapor pressures of TBE and water as a function of temperature.

Jan 1, 1972

By M. G. Zabetakis, T. D. Moore

The use of a partially slotted 6.5-inch-inside-diameter vertical pipe to remove methane from a longwall gob area at a depth of 2,260 feet in the Pocahontas No. 3 coalbed ms investigated. The value of gas removed by such a pipe under free-flow conditions was found to equal the cost of the installation in this case. Approximately 25 percent of the available methane passed through the pipe without the use of an exhauster; an additional 10 percent was removed when an exhauster was employed. The diversion of methane through a vertical slotted pipe to the surface permitted the use of increased mining rates and decreased the ventilation air requirements.

Jan 1, 1972

By Richard J. Kline

The underground mining industry is presently using the fluid network analyzer and digital computer to analyze ventilation systems. The availability of the digital computer and ventilation programs to mining companies has escalated its use, permitting the design and modification of new or existing mine ventilation systems to be projected completely and thoroughly with consistent precision. Because the analog computer has been analyzing ventilation systems accurately for many years, a comparison of the analog and digital methods was warranted. This report summarizes a detailed comparison for one mine, based on parallel analyses by the two computer systems.

Jan 1, 1972

By C. C. Merrill

Columbium, tantalum, titanium, and zirconium are present in solid waste products generated by the chlorination of rutile used for production of titanium tetrachloride (TiC14). The columbium and tantalum were separated from titanium and zirconium by liquid-liquid extraction techniques using a secondary amine. Salts of these elements are in a leach liquor produced by water leaching of mineral waste from the chlorination of rutile. This waste, produced at the rate of approximately 50,000 tons per year, is about 40 wt pct water soluble. Leach liquors, separated by filtration, were further separated into a solid fraction and a liquid fraction by pressure hydrolysis, The solid fraction containing Cb, Ta, Ti, and Zr was dissolved in HC1-HF and used as a feed solution. Columbium and tantalum were removed from the organic extractant with 1 [N] HC1. A miniature 10-stage reactor showed that the columbium and tantalum present in solution could be separated with a continuous flow.

Jan 1, 1972

By A. Viksne

A series of tests were conducted by the Bureau of Mines to determine the best means of reducing noise generated by the detonating cord that is utilized for trunklines in quarry blasting. Ten different types of detonating cord were tested and evaluated for their acoustic qualities. The results of the investigation showed that noise levels produced by "low-core-load-per-foot" detonating cord "not covered" were lower than those produced by "high-core-load-per-foot" detonating cord covered with 6 inches of unconsolidated material.

Jan 1, 1972

By Mark I. Copeland

The formation of A1203 dispersoids 0,14 and less in size in dilute iron-aluminum alloys by internal oxidation in wet hydrogen and dispersion strengthening of iron by application of the technique to iron powder were found to be feasible by the Bureau of Mines. In flowing H2-1.5 H20 gas, A1203 dispersoids 0.1w and less in size formed (at 650° to 750° C) in Fe-l and 2 Al sheet material but not in Fe-3 or 4 Al alloys. With higher temperatures and/or higher H2O/H2 volume-ratio gases, A1203 and FeA1204 dispersoids >0.14 in size formed in all the sheet materials- Minus 100-mesh Fe 2 Al powders were internally oxidized under conditions that promoted formation of fine A1203 particles in sheet material, and then the oxidized powders were hydrogen reduced, sintered, extruded, and evaluated. During internal oxidation, fine A1203 dispersoids formed within the powder grains, and coarse FeA1204 particles formed on the powder surfaces and grain boundaries. The FeA1204 content was essentially eliminated during sintering by reacting with the unoxidized aluminum that remained in the center of the larger internally oxidized powders. The tensile strength at 800° C depended upon the aluminum-oxygen weight ratio of these elements in the extrusions and reached a maximum of 17,000 psi. The stress-rupture strengths at 800° C of the better alloys were comparable with those of type 310 stainless steel.

Jan 1, 1972

By R. L. Schmidt

The Methane Control and the Respirable Dust Groups at the Twin Cities Mining Research Center (TCMRC) cooperated recently in obtaining production samples of approximately 1 ton each, from the loading conveyors of a ripper, a borer, and a loading machine in conventional development headings. These samples were sized, in four stages, from plus 4 in to minus 10 µm. The conventional product had the least fines of the three production methods. The borer product had more fines than did the ripper product, but it also had a greater amount of large pieces. All three products, as sampled, had essentially the same amount of minus 10-µm particles. Photomicrographs and surface?-area comparisons were made. Gas -adsorption, surface-area determinations on particles under 37 µm give essentially the same value. Surface-area calculations, assuming spherical particles and no porosity, give a smaller area to the conventional product.

Jan 1, 1972

By George J. Conroy

Electrical power generation was studied in a laboratory-scale, open-cycle vortex MHD generator, which offers several advantages over straight-channel generators that require separate combustors. Compactness, lower capital cost, and high-energy release are obtained by combining the combustor and generator into one unit in the vortex generator. In addition, the vortex generator uses a simple solenoid rather than the more complex and expensive saddle magnet required for straight channel generators. Although the vortex generator must utilize combustion gases with a low Hall coefficient in order to be efficient in direct comparison to the linear generator, the primary motivation for this experimental device in terms of ultimate objective was to investigate the vortex generator with applications to direct coal firing and with combustion taking place in specially designed expansion nozzles. The vortex device offers one decided advantage over the linear device in this regard because slag deposits do not degrade or short-circuit the coaxial electrodes as is the case for a linear machine. The experimental vortex generator consists of a modified cyclone burner 7 ½ in ID by 21 in long, with the inner wall used as one electrode together with a coaxial center electrode. Power was obtained by impressing an axial field of 3,000 G from an air core solenoid magnet. Tests were conducted by seeding natural gas seeded with potassium acetate and burning with preheated oxygen-enriched air. Power generation was lower than calculated because theoretical plasma velocities were not achieved.

Jan 1, 1972

By Richard A. Dick

Eight blasts were fired in a 2-1/2-ft bench in the Stewartville member of the Galena Limestone formation in an aggregate quarry near Stewartville, Minn. The shots were dimensionally proportional to production-size bench blasts and were about 5 to 10 percent of full scale. The effects of site, timing of initiation, and burden-to-spacing ratio were studied in a 2 x 2 x 2 factorial experiment, using three boreholes, caw;, containing a 1/2-in charge diameter of high-density ammonia dynamite, in each blast. Detonation velocity measurements indicated that the dynamite detonated satisfactorily in the 1/2-in charge diameter. The effects of the three experimental variables were analyzed by weight for the percentage of oversized material produced and for size distributions determined by screening the entire muckpiles. The bench faces were painted before each shot in an effort to determine the origin of the oversized material. The square pattern (burden and spacing = 15 in) produced finer overall fragmentation and less oversized material than the rectangular pattern (burden = 15 in; spacing = 22-1/2 in). Sites 1 and 2 were about ft apart. Although site 2 produced slightly better overall fragmentation than site 1, the amounts of oversized material produced showed no significant difference. The timing of initiation (instantaneous or delayed) did not significantly influence the overall fragmentation or the amount of oversized material produced.

Jan 1, 1973

By E. G. Valdez

Three cryogenic systems that utilized liquid nitrogen, dry ice, and methanol with dry ice were investigated in conjunction with crushing and classifying techniques. The systems were used to aid in separating and reclaiming the metallic components contained in insulated wires, shredded automobile nonferrous metal concentrates, small motors, generators, and rubber tires. Wire strands, 2 to 6 inches long and insulated with polyvinyl chloride and neoprene, were chilled at -60° and -195° C, then roll-crushed and processed by water elutriation; this procedure resulted in two products--a sink fraction that was 99 percent metallic and a float fraction that was 99 percent nonmetallic. Excellent separation of zinc die-casting alloys from copper and aluminum contained in shredded automobile nonferrous metal concentrates was attained by chilling at -72° C for 1 minute, crushing in a grateless hammer mill, and screening. From the screened products, 97.2 and 100 percent of the copper and aluminum, respectively, were recovered in the plus Pinch fraction, and 100 percent of the zinc was recovered in the minus 1-inch fraction of over 97 percent zinc die-cast purity. Laboratory experimental results comparing direct and indirect chilling indicated that a sufficiently low temperature could be attained by indirect chilling to permit use of a liquid C02-dry ice system on insulated wires and mixed nonferrous metallic concentrates.

Jan 1, 1973

By G. L. Fitzpatrick

Future applications of seismic holography to "seismically transparent phase objects," such as rock inclusions, fracture zones, liquid-filled cavities, etc., will require techniques to improve the poor image contrast generally characteristic of these objects. Although conventional phase-contrast enhancement techniques could be used, these methods involve additional optical elements such as quarter-wave spatial filters. Owing to the anticipated practical difficulties of properly alining such optical devices and properly locating poorly defined image planes and filter planes, this approach is not considered to be well-suited to the case of seismic holograms and their laser reconstructions. Results similar to those achieved with spatial filters may be obtained without filters by specially processing the seismic hologram data. The new process, which is an extension of Gabor's subtraction holography, achieves an improvement in contrast by an interferometric technique. The process involves adding a ?before" hologram without an object present to a 90° phase-shifted "after" hologram with the object present. Then, the combination is reconstructed with a laser or by computer. Not only is the image contrast improved in such processed holograms, but the images are also phase-contoured. In general, the latter feature is not to be expected when conventional phase-contrast enhancement techniques are employed. The new technique is experimentally verified by examining computer-generated synthetic seismic holograms rather than by examining actual seismic field data. However, results of this study are directly applicable to real seismic data and should prove useful in future applications of seismic holography.

Jan 1, 1973

By Joan C. Biordi

A molecular beam-mass spectrometer-low pressure flat flame apparatus has been constructed for the purpose of examining the chemical microstructure of normal methane-oxygen-argon flames and those inhibited with Halon extinguishants. Details of construction and performance of this apparatus and of related flame temperature measurements are given. Particular attention is paid to the empirical characterization of the perturbation to the flame caused by the sampling probes. The composition profiles obtained for normal flames are compared to those of flames inhibited by CF3Br. In addition to the usual stable species (CH4, O2, CO, CO2, H2O, H2, and H2CO), the inhibitor, its products and intermediates associated with its reactions could be followed. In particular, hydrogen bromide, bromine atoms, hydrogen fluoride, and carbonyl fluoride were observed. The relatively rapid disappearance of inhibitor and early appearance of fluorinated reaction products suggest a short lifetime for the CF3 radical in this system. Observation of COF2 suggests that CF3Br is effective as an inhibitor, at least in part, by virtue of its interference with the oxygen containing species of the normal chain reaction. Profiles of the 17+ peak at low electron energy suggests that the hydroxyl radical may also be sampled, but the profiles obtained are not yet sufficiently accurate to determine the effect of inhibitor on this important flame radical.

Jan 1, 1973

By R. C. Wang

Solid-liquid flow in different pipe geometries was investigated. This investigation was conducted by measuring delivered solids concentration and head loss. The delivered solids concentration was measured to study the effect of pipe geometry on the minimum carrying velocity above which solids do not lag behind the fluid. Head loss was measured to study the effect of pipe geometry on the friction loss. A mathematical formula was developed for determination of the minimum carrying velocity. Darcy-Weisbach's equation and Durand's equation were used for comparison of head losses of pipe shapes. Of the different pipe shapes studied, each having the same interior cross-sectional area, the rectangular pipe with the wide side oriented as the base yielded the lowest minimum carrying velocity at high solids concentrations. The minimum head loss at low velocity and high solids concentration also was attained with this pipe. Although the circular section is known to be the best for transporting liquid only, the present study suggested that pipe geometry is a factor in lowering the operating velocity and reducing head loss in solid-liquid flow.

Jan 1, 1973

By John Ward Smith

Aragonite, co-occurring with calcite and dolomite as matrix minerals, has been discovered in Mahogany zone oil shales of Colorado's Eocene Green River Formation, posing puzzles on the geochemical patterns of their separate origins, reasons for their simultaneous existence, and their interrelation. The presence of aragonite is demonstrated by X-ray diffraction. Amounts of aragonite and dolomite are significantly and inversely related, but the calcite quantity is essentially independent of either aragonite or dolomite quantity. A geochemical pattern outlining the deposition conditions that created the Green River Formation oil shale is postulated from characteristics of the oil shale. The development of the three separate carbonates--aragonite, calcite, and dolomite--the inverse relationship between aragonite and dolomite, and the independence of amounts of calcite and the other two carbonates are shown to be natural consequences of this oil-shale genesis pattern.

Jan 1, 1973

By J. S. Miller

The Bureau of Mines developed methods for fragmenting oil shale formations with chemical explosives to prepare oil shale for in situ retorting and to evaluate the extent of fragmentation by various methods. A combination of three methods of explosive fracturing was used: (1) The displacement and detonation of a liquid chemical explosive in a natural fracture system; (2) the use of 60-pct dynamite to relieve stress conditions of the rock around the wellbore; and (3) the use of pelletized TNT in a series of wellbore shots to fragment the oil shale. An attempt was made to seal or grout around the fragmented oil shale by drilling 67 holes and displacing approximately 200 bbl of neat cement in the fracture system to aid in evaluating the fragmented zone, Seven methods were used to evaluate the fragmented zone. The primary evaluation method was the recording of seismic waves to delineate the fragmented zone with results based on arrival time, amplitude, and record quality. The data from the seismic measurements indicated the extensively fragmented zone was approximately 95 ft in diameter and 70 ft thick. Results of the remaining methods of evaluating fractures--including air-flow tests, coring of the expected fragmented zone, elevation measurements to indicate overburden crowning, and surveys with high-speed camera, impression packer, and down-hole camera--agreed with and supported the data from seismic measurements. Further field application of explosive fracturing and evaluation methods is needed to determine when a zone of oil shale is effectively fragmented for efficient in situ retorting.

Jan 1, 1973

By W. T. Abel

The difficulties associated with wet-processing fine size coal led the Bureau of Mines to investigate a dry process for removing pyrite from coal pulverized to powerplant fineness. The dry process that was investigated consists of two cleaning steps: First, centrifugal separation is used to remove a fine, pyrite-depleted portion as a product; second, the remaining coarser, pyrite-enriched portion is taken to electrostatic separation in which pyrite is concentrated and rejected. Ball milling and Hardgrove milling were used to pulverize the coal. Three coals from the Pittsburgh seam were treated by the dry-removal process. Over 55 pct of the pyrite, which amounted to 70 pct of the available pyrite, was removed in a reject of 10 to 20 pct from one of the coals. Similar treatment of the other two coals removed about 35 to 50 pct of the pyritic sulfur, which amounted to about 70 pct of the available pyritie, sulfur from these coals. Both centrifugal and electrostatic separations were more efficient when pyrite particles were as large as possible. Separation efficiency was improved by confining the particle size of the feed to a relatively narrow range and by avoiding excessive amounts (more than 10 pct) of dust in the electrostatic range. The removal efficiency was increased with the use of stage grinding.

Jan 1, 1973

By J. R. Ross

The extraction and recovery of nitrate from waste solutions generated in the production of titanium were investigated using solvent extraction techniques. Laboratory studies and continuous tests in a small solvent-extraction system showed that up to 98 percent of the nitrate can be selectively extracted by a solution of tributyl phosphate in kerosine. The extracted nitrate can be recovered as nitric acid, at concentrations suitable for reuse, by stripping the loaded organic with water.

Jan 1, 1973