Search Documents

By Arthur W. Cooper

This paper contains a review of the development of blast furnace? slag handling and processing technology in the Ironmaking industry over the past 30 years, with an emphasis on economic and environmental factors. The requirements and practice of air-cooling slag for use as aggregate and of pelletizing and granulating slag for use in cement manufacture are described. The operation of slag pits, slag pots or ladles, the slag pelletizer and early granulation systems are compared with the new continuous .granulation, dewatering and handling systems developed in the past decade.

Jan 1, 1992

By M. Y. Mohassab-Ahmed

In an effort to develop a novel flash ironmaking process, the chemistry of selected slags was investigated. In different ironmaking processes, the molten bath (iron-slag bath) is expected to be in contact with gas atmospheres of H2/H2O, CO/CO2/H2/H2O, and CO/CO2. The latter was investigated to allow comparison with the blast-furnace conditions. The slag composition was selected to resemble that of the blast furnace with CaO/SiO2 in the range 0.8 to 1.4. The temperature range was 1550 to 1650°C. The oxygen partial pressure was maintained in the range 10-10 to10-9 atm. The effect of water vapor on the chemistry of the slag as well as the equilibrium reactions involving the slag has been studied for the first time. H2O dramatically affects the chemistry of the slag and strongly affect the phase equilibria in the slag as well as the equilibrium distribution of elements between slag and molten metal.

Jan 1, 2014

By Lauren M. Roberts, Ralph R. Sacrison

Pipeline or borehole free-fall transfer of material has long been done in support of underground mining. This paper addresses some characteristics and design elements in selecting systems suitable to the transferred media and the mine requirements. Though aspects of overall systems are discussed, principal attention is directed to the slickline/dropline/transfer line and the discharge diverter/rockbox/energy dissipator/boot. These terms are common to these systems, often used interchangeably, and will be used as appropriate to the material, equipment and construction. Following several design sections, fabrication and construction, and system operating and maintenance procedures are discussed.

Feb 1, 2025

By Klaus Gamweger

"This paper introduces an innovative solution to open and close the tap hole of different furnace types in the copper industry with a slide gate system. Two plates with defined drilled holes are slid against each other, which enables effective starting and stopping of the copper flow as well as throttling. Typically, the copper is poured via a tap hole into a launder system by rotating the furnace into an appropriate position. Control of the casting rate is also performed in this manner. Or, in case of stationary furnaces the tap hole is opened by oxygen lancing and closed manually with a clay- or copper-cone. These procedures show a lot of disadvantages including splashing, oxygen pick-up, and energy losses as well as a severe danger for the working staff. All these problems can be overcome with an appropriate slide gate system.IntroductionThe control of the casting rate of a copper anode furnace usually is performed by rotating the furnace into an appropriate position. This implies that the taping starts with the tap hole at a very high position. Copper splashing and an uncontrolled oxygen pick up are - with several more disadvantages - the consequences. RHI AG has developed an innovative solution for copper applications to open and close the tap hole with a slide gate system which allows also an accurate control of the flow rate. By using this system it is possible to start the casting procedure with the tap hole at the deepest position, directly above the launder. This paper presents this new slide gate system in detail and shows the advantages in production and safety issues."

Jan 1, 2012

By George J. Young

(San Francisco meeting, October, 1911.) THE nature of slimes handled in the treatment of gold- and silver-ores has been discussed in technical literature to a considerable extent. The subject of slime-filtration from the practical worker's stand-point has also received much comment, and scattered through the literature of the subject are descriptions of many slime-filtration installations. Articles of this nature serve a valuable purpose and assist materially in the design of new and the improvement of old plants. The subject of the physics of slime-filtration has been touched upon to only a slight extent. The underlying principles are worthy of more intensive study and experimentation than they have received, and the main purpose of this paper is to present the results of such study and experimental work as will serve to make clear in part at least many of the principles which control the filtration of slime. Nature of Slime. Much has bean written concerning an accurate definition of the term ? slime," but no comprehensive definition seems to be generally accepted. The reason for this is clear. A slime consists of at least three different substances, each, when separated, possessing distinctly different physical and to a certain extent chemical properties. These substances are extremely fine sand, a colloidal material which may be and generally is in a coagulated condition, and a colloidal material which is in a non-coagulated condition. Suspending a slime in a relatively large volume of water by shaking and allowing sedimentation to take place, results in the fine sand settling out with comparative rapidity, followed by the coagulated material, which settles much more slowly and finally a certain portion remains

Nov 1, 1911

By M. Mrost

Slimes disposal at South African gold mines by M. MROST*. M.Sc. (Rand) (Fellow) The soil mechanics, civil engineering, and environmental considerations applicable to the construction of slimes dams on the Witwatersrand gold mines are discussed. It is concluded that, though the procedures used in the construction of dam embankments do not accord with the best possible practice, they are entirely adequate in current local circumstances, provided that proper precautions are taken to ensure that the wall foundations are sufficiently permeable and strong, and that the dams are protected against erosion. If current trends towards larger mining and metallurgical complexes continue, it may become necessary to build larger, higher dams, and to adopt slimes embankmentbuilding practices that are inherently more reliable.

Jan 2, 1974

By C. E. Cairnes

The Slocan mining camp in Kootenay district; British Columbia; has long been noted for the great number of its silver-bearing deposits; and for the success that has; in many instances; attended their development. The orebearing area lies east of Slocan lake and mainly within a radius of 6 to 8 miles of the mining town of Sandon. Within this limited area 135 or more properties have shipped ore in quantities of from 100 tons or less to more than 500; 000 tons; and with a total value in silver; lead; and zinc ranging from a few hundred dollars to well over $10; 000; 000. Of the three metals; silver has easily ranked first in value; with lead second and zinc third. Zinc production; however; made slow progress in the early years; and with . the exception of the Lucky Jim mine; and a few others where high-grade ore could be readily hand-sorted; was a detriment to the silver-lead ores until improved methods of separation enabled it to take an important place in the mineral production of the Slocan.

Jan 1, 1954

By James P. Savely, Victor L. Kastner

Inspiration Consolidated Copper Company is currently mining in four pit areas; Live Oak, Red Hill, Thornton and Joe Bush Extension, near Globe, Arizona. Small satellite orebodies lying outside the main pits have been mined out in a series of small open pits. Major slope instability has affected production in every pit. Some consequences of the instability have been; (1) Serious interruption of mining plans, which resulted in deferred ore production, lost ore, reduced mining rates and increased stripping requirements. (2) Forced replacement of crushing facilities. (3) Serious effects on other production facilities. The introduction of a slope stability monitoring and control function as an integral part of mine planning has been successful in reducing the impact of these failures and will eventually result in economic pit design based on probabilistic slope analysis. This case history presents a brief review of the problems associated with slope instability at Inspiration's mines followed by a more detailed report on one specific failure area in the Thornton pit where the use of horizontal drain holes for slope stabilization appears to be successful. Relationships between slope movement rate, rainfall, and mining activity are shown.

Jan 1, 1983

By E Shilov, R Dixon, L Tovey

BHP Western Australian Iron Ore (WAIO) operations use a suite of slope monitoring systems which are deployed to operational areas based on the ground control risk. Slope Radars are one system used within WAIO, having recently deployed and integrated a network of 22 radar systems across the operations. The integration required the development of supporting network architecture, infrastructure, virtualised hosting, security protocols and a technology support model. This has enabled data transfer between the physical radar systems located in open pits, to on-site offices, a vendor supported remote control room in Indonesia and the WAIO Integrated Remote Operations Centre for data analysis and monitoring of system and displacement alarms 24/7. The typical technical skillset of a Geotechnical Engineer does not include the knowledge and capability to understand and develop the supporting IT infrastructure required for establishing an integrated radar monitoring network. This paper will provide a discussion of the technology considerations for integrating radar systems and highlight the importance of the developed partnerships between internal geotechnical and technology teams and the external vendor team to ensure a reliable, robust and scalable slope monitoring solution.

Nov 29, 2022

By J. M. Réjean Gagnon

"Quebec Cartier Mining Company is currently mining a low-grade iron ore deposit in northeastern Quebec. The Company is producing some 8,000,000 dry gross tons of concentrates per year, grading about 66 per cent iron. The pit, which is located on the keel or hinge line of a fold, will eventually be about 1,000 feet deep with a surface area of 8,000 by 2,600 feet. The most significant structural discontinuities in the mine are the natural bedding planes and secondary perpendicular joints. The exposed walls are subjected to a sub-Arctic climate and heavy blasting occurs approximately six times a month.QCM utilizes design and operating techniques to control rock fall. Steps are also being taken to analyze the ultimate over-all pit slope stability."

Jan 1, 1968

By J. L. Workman

The stability of spoil and highwall slopes are important to successful strip mining. This paper discusses soil parameters of importance in stability analysis. The common mechanisms of spoil failure are discussed. Modes of highwall failure are also outlined. The importance of water to stability is presented. Dragline mining methods most suited to creating spoil and highwall profiles that address stability needs are provided. It is concluded that groundwater and surface runoff must be well controlled, and that it will often be necessary to modify spoil and highwall configurations to achieve a stable overall slope angle.

Jan 1, 1996

By Peter N. Calder

The orientation of planes of inherent weakness (joints) with reference to an excavation in rock is the critical factor determining stability. The purely frictional 'residual' strength remaining following the breakdown of initial cohesion is the only strength which can be counted on to resist sliding for the long term. A simple method of resolving driving and resisting forces in three dimensions along joint intersections 'undercut' by the excavation is presented. Contrary to the case of slope failure in soils, it is shown how significant changes in the slope angle sometimes have no effect on the degree of stability pre-sent in rock slopes. Wall control by reorientation of the slope, the use of cable bolts and water diversion are briefly discussed.

Jan 1, 1970

By Nick Rose, Mathieu Veillette, Matthew King

"The Teck Highland Valley copper (THVC) mine is located approximately 55 km (34 miles) southwest of Kamloops and approximately 20 km (12 miles) west of Logan Lake, BC, Canada (Fig. 1). Mining at THVC is conducted at three openpit operations comprised of Valley, Lornex and Highmont with a total annual output on the order of 300 kt (330,000 st) copper concentrate and 5 kt (5,500 st) of molybdenum concentrate. The Phase 8 pushback in the Valley Pit (Fig. 2) was mined from 2011 to 2016. Successful slope steepening occurred in the later stage of the pushback with the implementation of presplit blasting in 2015 and 2016.This article summarizes the investigation and design approach including: structural analysis, kinematic assessments of bench breakback potential, development of discrete fracture networks (DFNs) to characterize discontinuity fabric, rockfall modelling, 2D anisotropic limit equilibrium and 2D distinct element modelling, assessment of potential kinematic failure modes affecting double benches with 3D distinct element modelling and improved blasting techniques using e-dets. THVC is currently undertaking a mine life expansion involving the pushback of the west wall of the Valley Pit above Phase 8 to extend the mine life to 2029. Engineering geologyThe east wall slope in the Valley Pit is comprised of a 350-m (1,148-ft) thick sequence of glacial valley sediments that occur along the Highland Valley (Fig. 2), exposing an overburden slope up to about 225-m (740-ft) high below the crest of the ultimate east wall. The glacial overburden units consist of pro-glacial outwash and glaciofluvial deposits, glacial outwash sands and gravels interbedded with till and alluvial fans consisting of cross-bedded sands and sandy-gravels. Lacustrine sediments occur within the mid to lower portion of the glacial sequence and contain intervals of low-shear-strength clays and silts. Two large (1.3 and 7 Mt or 1.4 and 7.7 million st) waste rock buttresses were required to maintain slope stability using slot-cut and fill mining methods, as described in Fortin et al. (2011).The Valley porphyry deposit occurs in the central portion of the late Upper Triassic Guichon Creek Batholith, which intrudes assemblages of the Permian Cache Creek and Upper Triassic Nicola groups. The Valley deposit occurs in an area of intense fracturing near the intersection of the northerly trending Lornex Fault and the northwest to westerly trending Highland Valley Fault."

Apr 1, 2019

By Eleonora Di Mario, Colin B. Turnbull, Matthew G. Mills, Chengbin Miao, Wilhelm S. Degen

"In the past decade, the ‘zero-dredge’ philosophy has become the preferred option for the formation of marine seawalls and reclamations, compared to the partially or fully dredged options, as this solution presents several environmental advantages. Recent relevant project experience is presented herein in order to highlight key design principles and construction issues central to the successful construction and performance of a sloping rubble seawall founded on soft soil improved by stone columns. If designed and installed with proper quality control, correct treatment intensity and sensible construction staging, stone columns are a safe and cost effective method for seawall foundations. This paper provides guidelines with regards to the design, construction and quality control for the correct implementation of stone columns as a foundation element for sloping rubble marine seawalls.INTRODUCTIONBenefits of sloping marine seawalls founded on stone columnsTo suit the current environmental requirements in Hong Kong, recent projects are tending to favour zero-dredge solutions, such as the Hong Kong Boundary Crossing Facility and the forthcoming Three-Runway System. The installation of stone columns allows the underlying deposits, generally consisting of very soft to soft clay and silt (soft soil), to improve in strength to the extent that the seawall can be directly placed on the seabed. This negates the need to dredge the soft soil and, therefore, this ground improvement technique represents an ideal solution for zero-dredge projects.Stone columns can also provide several other beneficial effects, including: accelerated drainage, reduced settlement, increased slope stability and soil reinforcement in the event of an earthquake. Stone columns, in contrast to competing cementitious methods, are a very ductile foundation method. This ductile behaviour is part of the design concept of stone columns in soft soil. Past projects located in Hong Kong and elsewhere, with an improved soft soil layer thickness of over 15m, have shown that stone columns can remain fully functional in terms of both drainage and horizontal reinforcement, even after settlements of over 3m and lateral displacements of up to 1m have occurred."

Jan 1, 2017

By T. A. Rickard

Slovenliness is as reprehensible in words as in clothes. Much writing that we recognize as poor in style is merely sloppy. Just as some students postpone the necessary shave or forget to change their collars, so young engineers in writing drop their articles, definite and indefinite, or omit prepositions where they are required, possibly to compensate for these they use unnecessarily The work will begin [on] Saturday. The work will begin [on] Saturday. `Influenza seriously affected many mines [during] the last three months. Flotation in America [during] the last two years has made tremendous strides. Construction of the mill started [on] August 12, 1915, at which time 75% of the excavation was completed. The idea I wish to convey is [that] there are mineral deposits to which the present law applies badly. For this reason, if there was [for] no other, the ownership of the ore below and [of] the surface above should go together. When a unit of mapping is furnished, be the unit a claim or [a] group of claims, it is necessary .. . A fully stocked store was started in Park City and all employees [were] sold merchandise on a strictly cost basis. The word "merchandise" is left without government or agreement. I suggest: ". . . and merchandise] was sold to all the employees on a strictly cash basis.". The verb `be' is serving concurrently both as a principal and as an auxiliary in the following: At first the work was interesting and [was] liked by most of the men. The sulphide ore was more complex or [was] milled at an increased cost. The failure to repeat tie auxiliary verb in successive clauses is a common error, as in The filter is filled with liquid allowed to empty, and then ignited.

Jan 1, 1931

By Amilton Feliciano Castro

In this work, activated carbons (ACs) were prepared using Sewage sludge as starting material. The ACs were pyrolyzed in an inert atmosphere at 550 °C after independent chemical treatment with ZnCl2 or KOH with ratio of 1:1. The materials were used as adsorbents for removal of Cu(II) from aqueous solutions. The adsorbents were characterized using adsorption/desorption nitrogen isotherm, SEM (scanning electron microscopy). The results showed that copper removal could be linked to surface pH and compounds present on the surface of adsorbent. KOH-treated adsorbent has smaller surface area (186 m2 g-1) than ZnCl2-treated adsorbent (192 m2 g-1), however, KOH-treated adsorbent exhibited higher removal of Cu(II). The performance of KOH-treated adsorbent could be attributed to the presence of basic groups on the adsorbent surface. Liu isotherm model gave the best description of the equilibrium data. From the Liu isotherm, the maximum adsorption capacities at 298 K for KOH-treated, ZnCl2-treated and sewage sludge (without inorganic activation) adsorbents are 31.85, 19.79 and 3.513 mg g-1, respectively. The best desorption experiment was obtained using 1.50 mol L-1 of HNO3 as eluent. Recoveries of Cu(II) from Cu(II)-loaded adsorbents are 98.9% (ZnCl2-treated) and 95.5% (KOH-treated.

Aug 17, 2017

By W. Norman Sims

A number of forces are at work that are now having an influence on coal handling systems. Changes are occurring and will be occurring at an increasing rate during the next few years. 1. Environmental concerns will dictate that dust pollution and spontaneous combustion and its resulting problems be rigidly controlled. 2. Slurry pipelines will be a reality despite the opposition of the railroads because they are economical and make good business sense. Artifical roadblocks can only survive for a limited time. 3. Coal is now and will remain the most economic fuel, particularly for power generation. This is true in most of the developed nations not just the United States. Increase in demand requires a close inspection of transportation systems. 4. A projected major increase in the export of U.S. coals may never occur without major port developments not the least of which will be the ability to accommodate large ships without demurrage time now affecting such shipments at U.S. Ports.

Jan 1, 1982

By E. A. Reilly, G. R. Gardner, F. P. Lasseter

THE methods that may be applied to the treatment of slurries and water, as these are related to practical coal-preparation problems, are concerned essentially with the movements of solids suspended in water. It is assumed that there are no fundamental differences between the principles involved in the treatment of coal slurries and the phenomena encountered in general mineral-dressing practice, and the latter are presented in some detail. Basic principles ,are correlated with present practice for both the anthracite and the bituminous coal fields, and methods are discussed which are designed to utilize best all the material subjected to treatment and suggest a sound approach to the solution of problems relating to the return of clear water to process or to streams. In order to approach the practical phases of the subject with sufficient understanding of the basic principles, it is necessary to discuss two types of phenomena that are applicable. The first is flocculation and the second is sedimentation. Descriptive matter is given covering the various methods and types of equipment employed to conduct these operations, with emphasis on their application to water and coal-slurry treatment. DEFINITION OF TERMS Definitions of terms are consistent with modern developments, and on form, in general, with their usage in mineral-dressing practice. Because of variations in coal-preparation methods, it is impossible to define a rigid upper limit of particle size for a coal slurry or sludge which will apply generally. Limits vary somewhat with the particular treatment method employed at a given plant. For purposes of definition, this limit is chosen as the particle size for which preparation methods such as Chance cones and jigs are usually dispensed with, and other methods, such as the Hydrotator, tables, and froth flotation, are employed. Generally the limit will be 10 to 6 mesh. In assuming this variable upper limit of particle size in a coal slurry, it is recognized that the size ranges discussed will duplicate sizes dealt with

Jan 1, 1943

By E. A. Reilly, G. R. Gardner, F. P. Lasseter

THE methods that may be applied to the treatment of slurries and water, as these are related to practical coal-preparation problems, are concerned essentially with the movements of solids suspended in water. It is assumed that there are no fundamental differences between the principles involved in the treatment of coal slurries and the phenomena encountered in general mineral-dressing practice, and the latter are presented in some detail. Basic principles are correlated with present practice for both the anthracite and the bituminous coal. fields, and meth¬ods are discussed which are designed to utilize best all the material subjected to treatment and suggest a sound approach to the solution of problems relating to the return of clear water to process or to streams. In order to approach the practical phases of the subject with sufficient understanding of the basic principles, it is necessary to discuss two types of phenomena that are applicable. The first is flocculation and the second is sedimentation. Descriptive matter is given covering the various meth¬ods and types of equipment employed to conduct these operations, with emphasis on their application to water and coal-slurry treatment.

Jan 1, 1943

By David R. Mitchell, E. A. Reilly, G. R. Gardner, F. P. Lasseter

THE methods that may be applied to the treatment of slurries and water, as these are related to practical coal-preparation problems, are concerned essentially with the movements of solids suspended in water. It is assumed that there are no fundamental differences between the principles involved in the treatment of coal slurries and the phenomena encountered in general mineral-dressing practice, and the latter are-presented in some detail. Basic principles are correlated with present practice for both the anthracite and the bituminous coal fields, and methods are discussed which are designed to utilize best all the material subjected to treatment and suggest a sound approach to the solution of problems relating to the return of clear water to process or to streams. In order to approach the practical phases of the subject with sufficient understanding of the basic principles, it is necessary to discuss two types of phenomena that are applicable. The first is flocculation and the second is sedimentation. Descriptive matter is given covering the various methods and types of equipment employed to conduct these operations, with emphasis on their application to water and coal-slurry treatment. DEFINITION OF TERMS Definitions of terms are consistent with modern developments, and conform, in general, with their usage in mineral-dressing practice. Because of variations in coal-preparation methods, it is impossible to define a rigid upper limit of particle size for a coal slurry or sludge which will apply generally. Limits vary somewhat with the particular treatment method employed at a given plant. For purposes of definition, this limit is chosen as the particle size for which preparation methods such as Chance comes and jigs are usually dispensed with, and other methods, such as the Hydro-tator, tables, and froth flotation, are employed. Generally the limit will be 10 to 6 mesh.

Jan 1, 1950