Search Documents

By I. Silin, H. Wotruba, J. Huben, A. Ognyanova

"With increasing shortage of raw materials, the beneficiation of ultra-fine ores will play a larger role in the near future. Many established process technologies do not yield satisfactory separation results for ultra-fine materials. Without selectivity, high-grade concentrates cannot be produced. The material at hand is a taconite which had to be ground to d(90) = 25 µm to guarantee liberation of the iron oxides. The comminution was done by High Pressure Grinding Roll (HPGR) and resulted in smooth surfaces and clear grain boundaries. This is an indication of selective grinding and mineral liberation. Further processing steps included selective desliming, magnetic separation as well as reverse flotation. INTRODUCTION During the last centuries, the processing of iron ores became increasingly important. The coarse-grained, so-called lump ores that are ready for direct usage in blast furnaces without further processing are becoming gradually less abundant. The processing of ultra-fine-grained ores, which in addition require a complex ore beneficiation due to the composition of the material, will progressively gain relevance with increasing resource shortages in the future (Arvidson, 2013). The term “ultra-fine” does not hold a precise definition in mineral processing. In this paper, “ultra-fine-grained” ores are defined by the required grind size for full liberation smaller than 20 µm. Many established mineral processing technologies do not yield satisfactory separation results for ultra-fine materials. Thus, they are limited in their application to produce high-grade concentrates suitable for sintering and pelletizing for direct reduction processes. The production of a high-grade iron concentrate (over 68% Fe) with low silica content (under 2.5% SiO2) is possible from both magnetite and hematite containing ore. In addition to the mineral processing technologies (magnetic and gravity separation, flotation), technologies for the liberation of fine-grained iron ores need to be developed and improved. In contrast to the conventional wet grinding circuit by means of tumbling mills, several future trends in dry and wet grinding and regrinding are already in use. These include technologies such as vibration mills (Palla®Mill), stirred media mills (Vertimill®), vertical roller mills (Loesche) and high-pressure grinding rolls (HPGR) (Jankovic, 2015). This study preliminary investigated the mineral processing of a low-grade, ultra-fine-grained, complex iron ore in a laboratory scale after dry grinding by HPGR to 90% < 25 µm without consideration of the grinding, milling, energy and classification cost."

Jan 1, 2018

By Ye Junjian

The feed ore is the concentrate of low intensity magnetic separation of pyrite tailings, containing TFe47.47%, S19.41% and SiOpyrrhotite. The exploratory tests showed that using a process of flotation followed by magnetic separation could respectively obtain a sulphur concentrate of S 31.08% with a recovery of 82.89%, and an iron concentrate of TFe 59.97% and S 9.52%with a recovery of 30.93%. The reason of iron concentrates with high sulphur grade was that the sulphur grade of flotation tailings was 7.03%. So enhanced flotation for pyrrhotite was investigated in this research. Results show that when the natural pH of ore pulp varied from 5.5 to 6.0, a reagent combination of FS, LH, and BJ displayed the optimum flotation performance for pyrrhotite. After comparisons made on different flotation processing, the previous flotation flow of ?one roughing, one cleaning, one scavenging system and middling reprocessing?, was found, among others, to have the best flotation effect, as the grade and recovery of sulphur concentrate were 31.08% and 82.89%, respectively, and sulphur content of the flotation tailings was 7.03%. The above results indicated it was difficult to raise further the effect of flotation desulphurization. The authors therefore suggested that oxidizing roast should be adopted following the magnetic process for the purpose of further desulphurization. Besides, flue gas containing SO2 8.25%. And the valuable minerals are magnetite and 2 generated from roasting could be reused for sulphuric acid production. Keywords: pyrrhotite, enhanced flotation, desulphurization

Sep 1, 2012

By Y. H. Hu, X. X. Zhang, Z. F. Dai, H. J. Huang, Q. S. Huang

"In order to get a more comprehensive understanding of the interaction of fine fluorite particles and bubbles, the electro-flotation was conducted, a high speed CCD was used to determine the bubble size distribution, and the results were analyzed using the models of collision and attachment. The electro-flotation was performed in a modified Hallimond tube. The results show that for different fluorite with size of 0 -10µm, 10 -38µm, 38-74um, there is a matching range between the different particle sizes and cathode aperture size (38um, 38um, 74um) to reach highest recovery. In addition, improving the concentration of collector is benefit for the flotation recovery due to the ability of collector to decrease the bubble size and prevent the merger of bubbles. Furthermore, theoretical calculation of collision, adhesion probability and collection probability is in agreement with the experimental data for electro-flotation recovery of fluorite.INTRODUCTIONFluorite is widely distributed, and has been found in more than 40 countries around the world. As fluorite minerals are easy to float, flotation is used as the best method of the current recovery of fluorite (Yang and Ai, 2016; Chen et al., 2017). In the field of mineral processing, the flotation of fine particles is particularly difficult, caused by the small quality and large surface (Sun et al., 2006). Flotation is now considered to contain three subprocesses, including the collision, attachment and detachment between the particles and bubbles (Sun et al., 2011). The collision of particles with bubbles is related to factors such as particle size and density, bubble size, bubble rise rate (Qin et al., 2012). Zongfu Dai et al. (2000) summarized the particle-bubble collisions models in detail and compared the experiment results with the model predictions. However, particle-bubble interactions occur in complex and turbulent flotation environments (Xing et al., 2017). Both thermodynamics and dynamic factors affect the adhesion of particles on bubbles surface (Schulze, 1989; Shahbazi et al., 2010). Scheludko et al. (1976) believes that the necessary condition for successful adhesion of particles on bubbles is that the contact time is greater than the induction time. The probability of adhesion between particles and bubbles increases with the increase of bubble size, but if the particle size is too small, the probability of adhesion decreases instead (Ren, et al. 2014; Norori- McCormac et al., 2017). After the particles adhere to the bubble surface, the particles will slide down to the bottom of the bubble due to gravity. At this point, the gravity, inertial centrifugal force and fluid force promote the desorption of particles from the bubble surface, while the surface tension, surface hydrophobic force maintain the stability of particles-bubble combination (Ralston et al.,2017). In addition, in the process of rising to the foam layer, desorption can also occurs. The purpose of this study is to observe the flotation behavior of fine fluorite with different size and to get a more comprehensive understanding of the interaction of fine fluorite particles and bubbles."

Jan 1, 2018

By J-g. Cui, X-b. Guo, J-j. Wang, J. Qiao, H. Tian

"Rare earth elements have unique properties because of the special electronic structure. In this paper the improvement of refractory material performance by the light rare earth oxides was introduced. The experiments showed that adding a bit of rare earth oxide could obviously improve the performance of the refractory material. INTRODUCTIONIn recent years, refractory materials are widely applied in the steel smelting process as a ladle lining material. In China, although the total production of fire-proof material exceeds normal demand, but the quality and variety of fire-proof material still have a big gap with world advanced level. A number of refractory products need to be imported from abroad. With the rapid development of domestic steel production, the ladle lining with refractory is gradually running after the world advanced level on production technology, production variety, and quality level. It replaces some imported products meeting the needs of the development of the iron making production. Therefore, there is an important significance to research on solving the problems of the ladle refractory reasonably and avoiding or reducing blind and not proper use of the imported refractory ( Jing, 2007).On the other hand, rare earth oxide has some special excellent properties. Firstly, they are very good refractory materials with their high melting point;Next, they have good resistance to water and alkali resistance function;Thirdly, it is easy for rare earth oxide to generated composite oxide reacting with other metal oxide,achieving the purpose to improving the material properties (Xu, 1978; Diao, 1979). China has a variety of rare earth resources,and rare earth resources is more advantageous in Baotou,taking up about 36 percent of world reserves,which is the world's top of rare earth mineral. In recent years the rare earth products output has risen sharply and many varieties and specifications have appeared. So it is necessary to study the new field of rare earth compound to open up new markets. Thus, it has a very vital significance to promote the further development of rare earth industry, adjust the rare earth products structure, ease the contradiction between supply and demand, and improve refractory products quality and grade in order to better serve the main body production.I In this paper, the experiments are mainly for 210 tons of Al2O3-MgO style series refractory materials belong to ladle lining bag from Baotou Iron & Steel Group Corporation Sheet Factory. The improvement to the effect of refractory material performance is explored by using light rare earth oxides as additives."

Jan 1, 2012

By Wenzhou Yu, Cong Zhang, Wenhui Ma, Gang Wang, Kuixian Wei

"A novel technique was successfully developed for nickel further purification by vacuum directional solidification. The removal effect of impurities in nickel was studied based on theoretical analysis and experiments. High removal efficiency of impurities in nickel can be realized according to theoretical analysis. The experimental results show that the vacuum directional solidification treatment could increase the nickel purity from 99.96% to 99.996%. Since vacuum directional solidification could effectively remove the impurities from nickel with low contamination and low cost, it is a potential route to obtain high-purity nickel for commercial application.IntroductionNickel is widely used in metallurgy, machinery, petroleum industry, chemical industry, construction industry, light industry, and other industries for its ductility, medium hardness, ferromagnetism and high chemical activity. Nickel-based alloy is an important material for the key parts of aircraft, tanks, submarines, radars, nuclear reactors and aerospace fields [1-5]. Generally, nickel contains Si, P, S, Fe, Cu, Zn, As, Cd, Sn, Sb, Pb, Bi, Al, Mn, Mg and other impurity elements, which may hinder the commercial application of nickel. Therefore, it is necessary to refine the crude nickel for the high purity nickel."

Jan 1, 2014

By Z. He

Based on full investigation of the characteristic of sphalerite in the residue obtained from cyanidation leaching process and the study of the mechanism of the interaction between flotation reagents and sphalerite with the aid of electrochemical analysis, the reagent named YO was developed for eliminating the depression effect of CN- on sphalerite and reducing the dosage of CuSO4. The achievements have been used in commercial production for the treatment of the cyanidation residue to recover the zinc minerals, obtaining a zinc concentrate with grade of 56.49% Zn and recovery of 86.63% Zn.

Jan 1, 2014

By Daojin Cao

Aiming at many controversial reports on Raman spectral pattern of heptamolybdate ion in aqueous solution appearing in the literature and the absence of its standard pattern, the comparative investigations on Raman spectral pattern of saturated solution of ammonium heptamolybdate tetra hydrate were done. The results showed that the main vibrant frequencies of Raman spectral pattern of the saturated solution were in good agreement with those introduced in the literature, and that the intensity ratio (4.4) of the strongest peak to the second strongest peak recorded in Raman spectrum of the saturated solution had three obvious characteristics: it was greater than each of the results (ranging from 3.7 to 1.3) reported in the literature, much closer to that (4.7) of crystal and well conformed to the change rule of Raman spectra occurring in the process of the first-step polymerization of acidified molybdate solution. It was found that Raman spectrum of heptamolybdate ion in aqueous solution was determined by not only the main vibrant frequencies but also the intensity ratio, which is also the crucial result in this study. The comparative investigations indicate that the pattern of Raman spectrum of the saturated solution is the standard pattern of Raman spectrum of heptamolybdate ion in aqueous solution essentially. The affirmed standard pattern is reliable and can be used to the identification of heptamolybdate ion in aqueous solution, applied in the research of the equilibrium of acidified molybdate solution and the exploration of the best technologic condition for the production of high quality heptamolybdates.

Jan 1, 2006

By Gaifeng Xue, Lei Zhang, Xia Liu, Lina Wang, Pu Liu, Benquan Fu

"Experiments were conducted to investigate the behavior of the integrated process with a three-dimensional electrode reactor combined with Fenton process for coking wastewater treatment. Effects of initial pH value, reaction time, H20 2 dosage, Fe2+ dosage on Total organic carbon (f OC) removal rate were investigated. The kinetics of degradation of TOC from coking wastewater by three-dimensional fluid bed electrode reactor combined with Fenton process was also studied. Experimental results shows that three-dimensional fluid bed electrode reactor combined with Fenton process had better synergic effect, average 17.4% TOC removal rate was improved within an hour. It was found that TOC degradation in coking wastewater followed a pseudo-first-order reaction kinetic model. The optimum degradation efficiencies of TOC were up to 60% as pH3.4, 3.5 mM ofFe2+ andl.2-1.8ml/L H20 2 in 90min reaction period. Furthermore, the integrated process showed a rapid reaction performance at a low temperature within a short reaction time and remained high efficiencies for TOC removal. Overall, the integrated process was proved feasible for coking wastewater treatment in practical applications.IntroductionCoking wastewater is generated from coal coking, coal gas purification, and by-product recovery processes of coking, which is composed of phenolic compounds, heterocyclic compounds, polycyclic aromatic hydrocarbons, ammonia, cyanide, polycyclic nitrogen-containing aromatics, acyclic compounds, etc. Most of these constituents are refractory, poor biodegradability, toxic and carcinogenic['-31. Currently, coking wastewater is usually treated by different forms of A/O biological nitrogen removal process as the primary treatment process, but the aforementioned processes are not efficient enough to meet the requirements from the National Discharge Standard in China (GB13456-1992). According to the continuous requirement on improving environmental protection for coking industry (revised 2008), increasing wastewater utilization ratio and reducing discharge of effluent in the coke industry has to be implemented for cleaner production and sustainable development. Therefore, advanced technologies need to be developed to treat coking wastewater and reutilize the product as industrial cooling water, which would be one of the best choices to achieve zero discharge of wastewater and reduce water consumption per ton of steel [4-51 . In this study, three-dimensional fluidized bed electrode reactor combined with Fenton process was adopted to advanced treatment of coking wastewater, and the effects of operating conditions, including H2O 2 dosage, Fe2+ dosage, initial pH, and reaction time on TOC removal rate, were investigated. Meantime, study of kinetics of reaction was estimated."

Jan 1, 2013

By T. S. Qiu

In view of the bad effect that Na-bentonite direct adsorb Pb2+-containing wastewater, this article has carried out two kinds modification treatment on Na-bentonite: the direct microwave radiation modification and microwave radiation organic modification by adding quaternary ammonium salt?cetyltrimethylammonium bromide,and analysis the main influencing factors of the modification effect. In static conditions, preparing Pb2+-containing wastewater as the research object, it has respectively studied the effects of Na-bentonite, microwave soil of direct microwave modification and microwave soil of organic modification on the process of adsorption Pb2+, and discusses the effects of pH value, temperature, adsorbent dosage, stirring time on the adsorption Pb2+ in wastewater by modified bentonite, at the same time it does a verification test to the practical Pb2+-containing wastewater. Comparison the effects of adsorption Pb2+ in wastewater, the results show that organic modified microwave bentonite is obviously better than direct microwave modified bentonite and Na-bentonite, and can make 6 mg/L Pb2+-containing wastewater meet the national discharge standards. Through scanning electron microscope, the result of test is that organic modified microwave bentonite is the cause of improving adsorption Pb2+ in wastewater. Preparing modified bentonite by microwave heating will not only shorten the response time, reduce energy consumption and work-load, but also modified effect is good.

Jan 1, 2014

By Y. Kumagai, F. A. Souza

"Electroless plating process has been used in many fields such as automobile and electronic industries. Solutions used in these processes must be disposed or treated. Commonly, in these solutions metal ions, organic materials and others chemicals are in very high concentration. It is very difficult to keep the environmental regulations for disposal of these materials, and the cost of the plating process becomes higher.The objective of this study was to investigate the recovery of components of those baths in order to decrease the cost of the plating process as well as to meet the environmental regulation.In this study the recovery metal ions, sulfate ions, phosphite ions and organic compounds were investigated. Organic compounds used in electroless plating solutions are the organic acids. In this work the solvent extraction of the most used organic acids included citric, lactic, succinic, tartaric and malic was studied. The solvent phase considered in these studies was ethyl acetate.About 95% of the metal ion was recovered by chemical plating onto mica powder. The hypophosphite remained is oxidized to phosphite and with the sulfate ion, both are recovered as calcium salts by selective precipitation in pH 7 and 2 respectively. Organic acids were recovered by solvent extraction using ethyl acetate as solvent phase and the best results were for lactic acid and succinic acid.Along with this study, was developed the analytical parameters to perform wastewater analysis by using Ion Chromatography, High Performance Liquid Chromatography (HPLC), Fourrier Transform Infrared Spectroscopy (FTIR). Ion chromatography was used to perform analysis of sulfate and phosphite ions in liquid matrix, HPLC was used to perform analysis of organic acids in liquid matrix and FTIR was used for characterization of the solids obtained in the recovery processes."

Jan 1, 1997

By Jianbo Lan, Desheng Huang, Xiaoying Qiu, Zhaohua Ke, Liusheng Ge, Xinjin Xiao, An Guo, Qiaofa Lan

Magnesium salt rare earth enrichment (MREE) is a crucial intermediate raw material in the deep processing of rare earth elements and material preparation, serving as a front-end raw material for the synthesis of rare earth oxides. With the current disposal process for MREE, neutralization slag with high rare earth residue is generated during further extraction of rare earth from the MREE and accumulates in huge piles. Therefore, the combined disposal process of MREE and neutralization slag was put forward. MREE was solubilized using 4 mol/L sulfuric acid to achieve an endpoint pH of 0.75, dissolving the rare earth and obtaining an acid solution. The MREE and neutralization slag were added in a mass ratio of 1:2 to the acid solution sequentially. The pH of the endpoint was controlled to 4.8~5.0 for neutralization and decontamination. This resulted in the production of rare earth sulfate liquid of similar quality to the original MREE disposal process, meeting subsequent extraction requirements. The neutralization slag underwent a water washing process, with two washes (first with 0.2 mol/L acidity water at a solid-liquid ratio of 1:2 and second with deionized water at a ratio of 1:4), resulting in water-washing slag with a rare earth content of 0.24% and a rare earth yield of 97.08%. Notably, zero wastewater discharge was realized. This innovative process effectively addressed the challenges of high rare earth residue in neutralization slag and stockpile accumulation, offering valuable theoretical and practical insights for MREE disposal.

May 31, 2024

By Woo, Hur, Kim, Ki Nam, Seung Min, Kyoung Sik

Tandem cold mill (TCM) is a process to obtain flatness as well as thickness desired by the customer by rolling hot-rolled coils continuously. The final stand of the TCM plays the most important role of flatness control, which usually uses the real-time measurement at the exit. However, as the material property increases, it is not easy to handle flatness with only the final stand. In order to overcome such a limitation, we propose a feedback control method to strengthen flatness control for non-final stands. The proposed method was tested in an actual production line, and the effect is proved for 45K or less steel grade.

Oct 1, 2019

By R. H. Grau, C. D. Taylor, A. L. Martikainen

Utilization of belt air in underground coal mines has been discussed extensively during the last decade. The Final Report of the Technical Study Panel on the Utilization of Belt Air and the Composition and Fire Retardant Properties of Belt Materials in Underground Coal Mining formed by the Mine Improvement and New Emergency Response (MINER) Act of 2006 recommends research on leakage, use of booster fans, and escapeway safety. This paper discusses the role of ventilation modeling in evaluating primary escapeway pressurization in a three-entry development system to improve emergency escape in a coal mine using belt air. The intake entry of the National Institute for Occupational Safety and Health (NIOSH) Bruceton Experimental Mine was pressurized using a 1.1-m (42-in.) diameter, 37 kW (50 hp) fan. The work details air movement in the simulated three-entry system and the resulting leakage patterns. Three mine ventilation software packages were compared to analyze their performance in predicting the airflows and leakage conditions with different fan settings. NIOSH researchers found that the measurement results correlated well with the results of modeling.

Jan 1, 2010

Technology has no recognized rank in what is called polite literature; the subject-matter of engineering is not supposed to lend itself to artistic treatment; we are the hewers of wood and drawers of water to the high-priests of learning that live on the cold summit above our humbler dwellings. Therefore the hierophants smile at the notion of &apos;style&apos;- “that curiously personal thing”--in technical writing. The "great art" of Pater, the "inevitable phrase" of Raleigh, the "note of distinction" that Arnold demanded are said to be beyond the scope, as they are supposed to be beside the need, of a writer on geology or engineering. This is a narrow view. Science, no less than belles lettres, calls for the best exercise of the human intelligence; the art of writing should be employed as skilfully and as earnestly in a description of the structure of the Sierra Nevada, or of the construction of a tunnel through the range, as in a rhapsody welcoming the rosy fingers of the dawn. The idea still lingers that fine writing does not befit technology, even though the masters of the Victorian period- Huxley, Tyndall, Ruskin-proved that science is worthy to be arrayed in the best robes that the looms of thought can weave. At the beginning of these lectures I quoted Barrie&apos;s remark touching the inability of the scientific man to express himself. That imputation has been passed to the technologist, whose utilitarian pursuits are supposed to make him too clumsy for the refinements of human speech. We may not have acquired the self-consciousness of those writers on Art whose "power of expression is so cultivated that their sensual caterwauling may be almost mistaken for the music of the spheres"; nor can we imitate the politicians, who have the ability to speak far beyond anything that they may have to say; but we too have a litera-

Jan 1, 1931

By T. A. Rickard

Technology has no recognized rank in what is called polite literature; the subject-matter of engineering is not supposed to lend itself to artistic treatment; we are the hewers of wood and drawers of water to the high-priests of learning that live on the cold summit above our humbler dwellings. Therefore the hierophants smile at the notion of &apos;style1-" that curiously personal thingy-in technical writing. The "great art" of Pater, the "inevitable phrase" of Raleigh, the "note of distinction" that Arnold demanded are said to be beyond the scope, as they are supposed to be beside the need, of a writer on geology or engineering. This is a narrow view. Science, no less than belles lettres, calls for the best exercise of the human intelligence; the art of writing should be employed as skilfully and as earnestly in a description of the structure of the Sierra Nevada, or of the construction of a tunnel through the range, as in a rhapsody welcoming the rosy fingers of the dawn. The idea still lingers that fine writing does not befit technology, even though the masters of the Victorian period-Huxley, Tyndall, Ruskin-proved that science is worthy to be arrayed in the best robes that the looms of thought can weave. At the beginning of these lectures I quoted Barrie&apos;s remark touching the inability of the scientific man to express himself. That imputation has been passed to the technologist, whose utilitarian pursuits are supposed to make him too clumsy for the refinements of human speech. We may not have acquired the self-consciousness of those writers on Art whose "power of expression is so cultivated that their sensual caterwauling may be almost mistaken for the music of the spheres"; nor can we imitate the politicians, who have the ability to speak far beyond anything that they may have to say; but we too have a litera-

Jan 1, 1931

By Greg Corbett

The paper point out the styles of Pacific Rim epithermal gold mineralization. Some characteristics of differing styles of epithermal gold mineralization influence investment decisions (metallurgy, metal ratios, mining style), while others should be taken into account during prospecting (pyrite content and resistivity govern geophysical techniques, vein/breccia styles control drilling, gold distribution influences ore reserve determinations). Two groups of epithermal deposits are distinguished by the fluid style which controls ore and gangue mineralogy. High sulfidation systems develop from the reaction of hot acidic magmatic fluids with host rocks to produce characteristic zoned alteration and later sulfide (dominantly enargite-pyrite) and Au-Ag-Cu deposition. Ore systems display permeably controls governed by lithology, structure and breccias, typically phreatomagmatic breccia pipes, and should be distinguished from a group of generally non-economic acidic alteration including: steam heated alteration, lithocaps or barren shoulders, acid sulfate, and magmatic solfatara alteration.

Apr 24, 2001

By T. J. Lien

AMAX Coal Company&apos;s Belle Ayr coal dryer is the first industry attempt to commercialize sub-bituminous coal drying which has been the subject of laboratory and pilot plant tests for almost two decades. This paper presents the historical background, construction, start-up and operation of this adaption of fluidized bed coal drying technology to Powder River Basin coal. The flowsheet and operational problems encountered during plant start-up are discussed together with general material balance and product quality.

Jan 1, 1990

By Jorge MRS Relvas

Recent research both on active and fossil systems has demonstrated that shallow subseafloor replacement processes are not only viable depositional mechanisms for massive sulfide mineralization, but likely contributed as a major component of the mineralization occurring in large VHMS deposits and in many present-day seafloor hydrothermal systems. In the giant Neves Corvo deposit, as in many others VHMS deposits of the Iberian Pyrite Belt, there is overwhelming evidence for silicate-sulfide replacement processes being largely responsible for the efficiency of the ore-forming systems and huge size of the deposits. Textural evidences at all scales, coupled with a well-constrained mass-balance geochemical analysis, indicate that extensive replacement in the lavadominated volcanic rocks of the footwall sequence, and disseminated replacement mineralization in the volcaniclastic and/or sedimentary units were major mechanisms of ore formation in the Neves Corvo deposit. Shallow metal deposition prior to fluid discharge on the seafloor is likely to play a major role in seafloor massive sulfide mineralization. This premise should be envisaged as critical in evaluating the economic potential of seafloor resources, and should certainly be part of the equation when plans for seafloor mineral exploration missions are drawn.

Sep 14, 2011

By G. Kleyn

"Sub-standard practices and their adverse impact on safety performance remain a challenge in the South African gold mining industry. The purpose of this study was to investigate the root causes of sub-standard practices and the effect on safety performance in South African gold mines. The focus of the study was on the underground production operations at a gold mine in the Free State. The study consisted of three parts: a personal investigation into the causes of sub-standard practices at the mine, a comparison with the results of a cultural study performed at the West Wits mines, and a behavioural survey.The studies described in this article yielded similar results in terms of the key drivers behind sub-standard practices. It was found that substandard practices had a number of causes, and the origin lies within the habits, attitude, and behaviour of employees. Current methods of addressing sub-standard practices and improving safety performance were found to discourage employees from performing work safely and according to procedure. It was concluded that the lack of critical behavioural habits for the given work environment and job title could possibly be the primary reason for the occurrence of sub-standard practices. IntroductionSince the implementation of the Mine Health and Safety Act, 1996 (Act 29 of 1996) and the Mine Health and Safety Regulations, the South African mining industry has been striving to improve health and safety performance and has placed great emphasis on adherence to mine standards.The Act requires employers in the mining industry to report accidents, incidents, and dangerous situations to the Regional Principal Inspector of Mines in their area. The data provided by employers is captured and analysed by the South African Mines Reportable Accident Statistical System (SAMRASS) and made available for public viewing (Department of Mineral Resources, 2011).A review of the national mine-related accident statistics shows clearly that the South African gold mining industry has improved its safety performance markedly over the past decade, but is still facing major challenges (Figure 1). These include meeting the Mine Health and Safety Milestones (Department of Mineral Resources, 2011)."

Jan 1, 2016

By Thomas T., Read

IT will be recalled that when educational instruction for the mineral industry began at Freiberg, at the beginning of the eighteenth century, the original aim was to organize and systematize the procedures previously followed by young men in gaining -familiarity with the technology then in use. There must have been many other ideas current, even then, as to just what a young man needed to learn in order to become capable of assuming &apos;responsibility for the supervision and direction of such technical work. The problem in Europe was decidedly different .from that in nineteenth-century America, because some of the European mines were actually owned and operated by the governing authority and the others were supervised, regulated, and taxed by it. The American problem was the e5cient performance of technical operations; the European one was regulatory supervision. It was natural, therefore, that in the development of educational processes in Europe stress was laid on those factors which conserved and protected the interests of the state. The study of mineralogy and geology, leading to correct judgments as to the workability and value of mineral deposits; assaying, which gave the means of quantitative measurements, as did surveying; chemistry, which furnished a better basis of understanding for assaying, mineralogy, and geology; and physics and mathematics, which are the bases for the understanding and efficient use of mechanical appliances, became the core of systematic instruction, for the mineral industry. It was early recognized that men could learn more than was already known about all of these subjects and education took on that dichotomy which still characterizes it; the teaching of established knowledge to the unlearned, and that of extending of the bounds of knowledge, now loosely termed research, which after two and a half centuries of work still shows

Jan 1, 1941