Search Documents

By Jin-yan TIE, Ke-xin JIAO, Qian Li, Hai-bin ZUO, Jian-Liang Zhang, Meng SHEN

This paper designs three factors such as temperature, pH, conductivity and three levels of orthogonal test. Temperature is a significant factor. However PH and conductivity are not significant through poor analysis. Further research is conducted on the temperature. Temperature stability is 50 . Suitable water velocity is 2.3m/s, which is calculated based on the largest part of the heat flux intensity and the corresponding water temperature should be controlled with 1.5. Meanwhile, water velocity increased has little effect on the heat transfer capabilities.

Jan 1, 2015

By Serge Ouellet

Résumé Six modèles métriques de remblai cimenté en pâte (RCP) ont été suivis durant 120 jours par l?utilisation de deux méthodes géophysiques non-destructives : la résistivité et la micro-sismique. Les RCP étaient constitués de trois résidus miniers et de deux proportions de ciment (3% et 6% en poids). En parallèle, des cylindres de RCP étaient utilisés pour évaluer périodiquement l?UCS. La résistivité augmentait quasi-linéairement de 28 à 120 jours pour tous les RCP investigués. Des variations de résistivité selon le type de résidu et le pourcentage de ciment ont été observées. Une équation empirique a été dégagée entre l?UCS, la résistivité, le temps, la densité relative et le rapport eau/ciment (E/C). La mesure de la vitesse des ondes de cisaillement a permis de dégager une équation mathématique de type exponentielle qui relie la résistance mécanique sans correction préalable par les paramètres de la recette de RCP. La réalisation de ce projet avait pour but de dégager la meilleure approche non-destructive afin d?estimer la résistance mécanique des remblais en chantier minier. Sur la base des résultats obtenus, les deux méthodes utilisées ont donné des résultats probants afin d?estimer la résistance mécanique et les deux méthodes sont donc à même d?être utilisées en chantier souterrain. Abstract Six scale models of cemented paste backfill (CPB) were followed during a 120 days period using two nondestructive geophysical methods: resistivity and micro-seismic. CPB were made up of three mine tailings and two cement proportion (3% and 6% by weight). In parallel, CPB cylinders were used to periodically evaluate uniaxial compressive strength (UCS). Resistivity was increasing nearly in straight line from day 28 to day 120 for all CPB models. According to the tailing type and cement percentage, resistivity variations were observed. An empirical equation emerged from UCS, resistivity, time, specific gravity of tailings and, water/cement ratio. The use of shearwave velocity allowed to identify a mathematical exponential equation related to mechanical strength without prior correction of the CPB?s formula parameters. The purpose of this project was to identify the best non-destructive approach in order to evaluate the mechanical strength of backfill in a mine site. On the basis of those results, both methods gave conclusive results in order to estimate mechanical strength and both methods can be used in underground operations.

Feb 1, 2008

By Tracey Bodnarchuk, Philipp Mirzoev

Sulfate balance control is a common problem for zinc plants. Roast-leach-electrowin plants are mostly concerned with the over-generation of sulfates while for the HudBay direct leach plant both extremes are possible including potential necessity to buy sulfuric acid to replenish a sulfate-depleted circuit, which makes the problem doubly important. Quantitative methods were applied at the HudBay plant to analyze sulfate generation/depletion based on a local sulfur balance and sulfate extraction calculation in the leach circuit, using a Pb-tie method. Main factors were established influencing sulfate generation/depletion, including the critical role of Pb and pyrite. Regression analysis proved to be effective and allowed the quantitative prediction of Pb concentrations necessary to reach the equilibrium for the sulfate balance. This in turn provided a firm basis for a sulfate-control strategy realized through concentrate blend correction, which allowed the plant to fine-tune sulfate generation/depletion effectively reducing economic consequences of excessive/deficient sulfate generation.

Jan 1, 2015

By A. H. Kaksonen

Numerous reactor designs for biological sulfate reduction have been reported. Fluidized-bed bioreactors (FBR) can efficiently retain biomass and allow high mass transfer and reaction rates. This work reviews the development of various sulfate-reducing FBR processes for treating acidic metal- and sulfate-containing waters and recovering metals from bioleaching liquors. The FBR process performance was evaluated with continuous flow experiments under various operational conditions: fluidization rates, influent pH values, metal, sulfate and salt concentrations, hydraulic retention times, electron and carbon sources, and temperatures. Substrate utilization and sulfide inhibition kinetics were determined with batch FBR-kinetic experiments. An artificial neural network (ANN) model was used to predict the performance of the FBR. Sulfate-reducing bacteria (SRB) were characterized in FBRs with molecular and culture-based approaches with the aim to gain a better understating of the bioprocesses. Based on the studies, FBRs are well suited for the combined removal of metals, acidity and sulfate from water.

Jan 1, 2010

By Steve Lloyd, Ryan J. Foy, Brandon Steinborn, Jerome P. Downey

Research was performed to evaluate copper and silver extraction from samples of bornite flotation concentrate. Sulfation roasting experiments were performed in a rotary tube furnace, a fluidized bed reactor, and a static bed muffle furnace. Roasting was plagued with rapid, lowtemperature calcine sintering, apparently related to the presence of organic matter in the concentrate. Calcine entered a weak acid leaching process to remove copper, and silver was extracted from the weak acid leach residue in a ferric chloride and hydrochloric acid solution. Copper extraction efficiencies in excess of 90% were attained in the weak acid leach while 90% silver extraction was achieved in the ferric chloride leach, along with copper and lead extractions as high as 93% and 99% respectively. The two-stage leaching process resulted in overall extraction efficiencies of 99% copper and 90% silver.

Jan 1, 2015

By F. H. A. Abdalla

A process is described for the recovery of valuable nonferrous metals from steelmaking dust by suiphatizing roasting using ammonium sulphate. Maximum recoveries of soluble metal sulphates achieved at optimum conditions were> 99.0 %. Selective metal separation of the soluble sulphates in the leached liquors were performed either by controlling the roasting temperature or by adjustment the pH values of the leached liquor ranging from 3.6-6.2. Either pure zinc oxide orland tin oxide could be obtained at optimum conditions, and the products were evaluated chemically and by X-ray analyses. The residues rich in iron oxide can be removed and recycled. The mechanism of sulphatizing roasting process was considered. A general flow-sheet for the overall process of treatment the steel making dust to recover its valuable nonferrous metals was suggested, which ca be applied for other nonferrous bearing materials.

Jan 1, 1996

By Larry F. McHugh

Current sulfide ore processing methods involving mechanical sizing of ores, froth flotation, electro-winning, solvent extraction, smelting and roasting are quite effective but typically represent a significant energy and environmental cost. This paper is the subject of a recent patent application and development program involving major improvements in sulfide ore processing. This two-step ?looping oxidation? process effectively removes sulfur while producing materials of adequate purity in an energy proficient and environmentally friendly manner. The first step results in a metal sub-oxide and a highly concentrated sulfur oxide off-gas stream. This gas stream can be processed for recovery in a more effective manner regarding both energy and capital equipment costs. In the second step, this metal sub-oxide is further oxidized to efficiently generate energy that can be recovered and utilized without the typical complications of an ?acid gas? stream process. Additionally, a portion of the final fully oxidized product can be looped back to the first step as the oxidizing agent. This process will be described in detail and compared to existing technologies in the area of energy efficiency, and off-gas environment treatment energy requirements.

Jan 1, 2008

By Richard W. Hutchinson, Christopher Osterman

Abstract -The Selebi-Phikwe deposits are hosted by amphibolite to granulite facies gneisses of the Limpopo belt. The sulfide orebodies are generally stratiform and conformable to the foliation of the wallrock gneiss. Sulfide remobilization has occurred during metamorphism and has produced discordant sulfide veins, called piercement structures, which project into the hanging wall and foot­ wall gneisses. These piercement structures are compositionally similar to the stratiform sulfides, consisting mainly of pyrrhotite, pentlandite and chalcopyrite. However, texturally the piercement sulfides are coarse grained and inclusion-free, whereas the stratiform sulfides are fine grained and packed with tectonically produced wallrock inclusions. The piercement structure sulfides and adjacent stratabound sulfides were sampled and analyzed for major base metals and PGE's for comparative purposes. Most of the piercement structures were enriched in Cu, Ag and Au, whereas they were generally depleted in Ni, Co, Fe and PGE's. Changing elemental associations were observed from the stratabound sulfides and along the length of the piercement structures. This and the degree of depletion or enrichment of various major and minor elements in the sulfide piercement structures may reflect the relative mobilities of metals under metamorphic conditions. The similarities between sulfide piercement structures and the footwall Cu-POE veins in some Sudbury deposits are reviewed.

Jan 1, 1994

By Alvear G. R. F. Flores

It is now 35 years since the organization of the first sulfide smelting conference in 1983. Since then, the smelting base metals industry has experienced several changes driven by the necessity to improve economic, operational and environmental performances and resource efficiency and meet the increasing market demand for metals. In this continuously challenging environment, it is relevant to recognize which are the main challenges that the industry will face in the coming years and critically address our preparedness to respond to them. This analysis have to consider not only the effort required from the fundamental research and technology aspects but also how these pillars interact with the drivers behind the base metals industry. This paper discusses some relevant aspects required to continue developing the base metal industry focusing on copper. Aspects such as the need to supporting the generation of fundamental metallurgical knowledge, acquisition and proper use of data with advanced analytics methods, technological innovation to develop sustainable process flowsheet are discussed with emphasis on efforts conducted by Aurubis.

By Dale A. Shay, Roy R. Cellan

The Santa Fe Mine, located in west central Nevada, began leaching ore in 1988 and completed ore processing in 1995. Homestake Mining Company has completed final reclamation of the site, including remediation of bare surface soils resulting from the oxidation of sulfide minerals and migration of acidity in the mine waste repositories. The need to remediate oxidized sulfides and mitigate resultant acidity at the Santa Fe Mine emphasizes the economic, reclamation, and environmental advantages for understanding and pre-planning for management of potential sulfide wastes during mine planning phases. The lack of pre-planning by mining companies for sulfide waste management was common in the 1980's due primarily to mining of reserves characterized largely as oxide deposits and to the common opinion that low moisture regimes in arid or semi- arid climates would not allow for significant acid generation. Since the 1980's, operational experience has shown that sulfide wastes, deposited randomly in waste dumps and without adequate planning for final reclamation success, can create final reclamation problems that are very costly to remediate. While mine waste characterization, waste management plan compilation, and in-pit selective waste handling procedures add operational costs, the reclamation experiences at the Santa Fe Mine are indicative that pre-planning and management is worthwhile both in actual overall cost efficiency and in successful reclamation of the mine site. The reclamation program at the Santa Fe Mine shows Homestake's continued commitment to the successful management and reclamation of their mine sites.

Jan 1, 2000

By M I. Pownceby

High temperature roasting studies on chrome-spinel contaminated ilmenite concentrates showed that sulfur, introduced through a sulfidising roast treatment, selectively reacted with the chromium in the spinels. The roast treatments were carried out in a laboratory scale rotating drum kiln using a standard Becher-style heating profile (10 h, 1075ºC), char as the reductant, and variable amounts of added elemental sulfur (0 - 3 wt per cent).After roasting, bronze-coloured grains were visible representing chrome-spinels that had undergone selective sulfidisation. SEM imaging of the products showed that sulfur was preferentially concentrated in ~5 - 15 µm thick rims fully enclosing the chrome-spinel grains. The sulfur-rich rims became a sink for manganese (Mn) from the ilmenite resulting in the rims being rich in Cr-Mn-Fe-sulfides. Quantitative electron probe microanalysis of phases present within the rims identified two sulfide phases. The first sulfur-phase (S-phase) was low in Mn (1 - 3 wt per cent) and high in Fe, Cr and S, while the second S-phase was considerably higher in Mn (30 - 35 wt per cent Mn) and lower in Fe and Cr. The dramatic change in the composition of the chrome spinels after sulfidisation is likely to significantly alter their physical properties (eg hydrophobicity, conductivity, etc). This should make their physical separation from the ilmenite potentially easier than roasting/magnetic separation methods.

Oct 5, 2011

By H. T. Rall

This report summarizes a systematic 20-year study of the organic sulfur compounds in Wasson, Texas, crude oil and, to a lesser extent, of three other crude oils, that has culminated in some 200 individual sulfur-compound identifications. The development and application of special separation and identification techniques generally suitable for the characterization of sulfur compounds in any crude oil are discussed. This report reviews early sulfur literature covering petroleum sulfur compound identifications completed before this study was begun, and cites 58 papers resulting from this work. The sulfur compounds in petroleum, both as to type and quantity, have long been of concern to the petroleum industry, and such compositional data are not only of theoretical interest, but also of practical value.

Jan 1, 1972

By Helena Byrdziak

Polish Copper Industry, located in the Lepica-Glogów region and operated since the 1970's, includes four mines and two smelters, "Legnica" and "Glogów", the latter consisting of "Glogów" I" and "Glogów II" both having different technologies. The "Legnica" and the "Glogów I" smelters using shaft furnaces, so sulfur elimination largely takes place during batchwise converting, resulting in fluctuation SO2-concentration between less than 1% up to 10% in the converter pas W the sulfuric acid plants. The ensuing difficulties of the past have now largely been overcome. Introduction of flash smelting at "Glogów II" with subsequent acid making by double SO2-conversion from the stable process gas, contributed significantly to further reduction Of SO2-emission. In 1994 a new double conversion sulfuric acid plant was installed at "Glogów l" as well as a "Solinox" desulfurisation plant at "Legnica", further reducing SO2 emission considerably, The next step towards this goal under consideration is a semi-dry desulfurization system for the "Glogów I" power station, SO2- abatement measures by KGHM and the results thereby achieved are presented.

Jan 1, 1996

By N. A. Warner

Fundamental studies on the reaction of limestone or dolomite at high temperature with S02 are extended to the realm of large scale primary copper smelting. Whereas flue gas desulfurisation in the electric power utility industry is concerned with S02 concentrations normally less than 0.5 percent, high temperature smelting gases can have S02 levels approaching 100 percent. The reaction involved is very exothermic so proposals are made in this paper for returning the heat generated in sulfur fixation directly back to the copper smelting process. This integration leads to metal production with lower energy requirements than current technology. The anhydrite reaction product can either be disposed of locally with minimum adverse environmental impact or upgraded to a value-added product. It is assumed, of course, that no viable market exists to support sulfuric acid production.

Jan 1, 1996

By Geo Ashley

THE following paper is intended to be suggestive only, and to open the way for discussion and further observation. Its preparation was requested only two days before the time limit set for the submission of the papers comprising this symposium. Thus no time existed for detailed studies so it is largely a memorandum of such facts as have come incidentally to the notice of the writer in the study of coal in the field. The field study of sulfur in coal has received very little special attention or description from coal students. The presence of sulfur concretions is noted in hundreds of descriptions, and certain benches of a coal bed may be described as "sulfury" or the presence and position of sulfur bands may be noted in coal sections in connection with sampling. It may be accepted that some sulfur is present in all coal. The amount varies greatly in different regions, in different beds, and in the same bed in different areas. The anthracite of Rhode Island comes the nearest of any coal known to the writer of being free from sulfur, several analyses of that coal showing less than 0.1 per cent. Subbituminous coals in Colorado in a few places have close to 0.2 per cent. of sulfur on the dry-coal basis and in other states subbituminous coals approach this lower limit. Bituminous coals seldom run under 0.4 per cent. of sulfur on the dry basis, though in a few places dry bituminous coals in Colorado and Washington have between 0.3 and 0.4 per cent. The better known bituminous coals have almost everywhere over 0.4 per cent. The best of the Pocahontas and New River coals run close to 0.4 per cent., but there is very little commercial coal in Pennsylvania, Ohio, Indiana, Illinois, Kentucky, or the other states that runs under 0.5 per cent. on the dry basis. From these minimum figures, the amount will range up to 5 or 6 per cent. or higher if visible sulfur is not excluded. It must be remembered that the usual -analysis of a coal bed is not intended to give the total proportion of sulfur in the bed but the amount in the coal after the removal of the more obvious and larger sulfur masses.

Jan 9, 1919

By D. Silva-Galvan, R. D. Morales, S. Gonzáelez-López, A. Romero-Serrano, G. Plascencia-Barrera, F. Chavez-Alcala

This work is focussed on lead decopperising by two techniques: conventional top addition of sulfur and injection of sulfur powder. It is found that the first method proceeds under equilibrium conditions and the second one depends on kinetic considerations. Experiments were carried out using 15 kg lead baths at two temperatures, 340°C and 380°C. The carrying gas used for the injection trials was nitrogen at flow rates of 6.3 and 18.6 L min- 1• The results show that 'decopperising process is more efficient at temperatures close to the melting point of lead for the sulfur top addition process, whereas high temperatures produce better copper removal for the injection of sulfur powder. Besides, the sulfur injection with the higher nitrogen flow rate (18.6 L min-1) produced higher decopperising rates. Thermodynamic and kinetic models are used to simulate this lead refining process.

Jan 1, 2000

By David B. George

Kennecott recently completed an $880 million modernization and expansion of its smelter and refinery to process all concentrates from the Bingham Canyon mine. This is the first application of Kennecott-Outokumpu Flash Converting. Molten material movement by overhead cranes is eliminated and high levels of oxygen enrichment result in very low process gas volumes and exceptionally control of sulfur oxide emissions. All existing in-plant hygiene, safety, and environmental regulations will be met and the smelter is positioned for anticipated more stringent future regulations. Sulfur capture is 99.9 percent resulting in sulfur dioxide emissions less than the 112 kg/hr Air Permit limit, making the smelter the cleanest in the world.

Jan 1, 1996

By D. C. Sisti

A technical evaluation of actual performance of the preparation facilities at Beaver Consolidated Coal Co.'s Stinson plant is presented, with special emphasis on sulfur reduction in 1-1/2 x 3/8 in., 3/8 in. x 28 mesh, and 28 mesh x 0 size fractions. Evaluation of the heavy medium section of the plant and the treatment of the 28 mesh x 0 coal is included. Design criteria considered for sizing and selection of equipment required to process 1-3/4 million tpy of raw coal on coals of divergent washability characteristics are summarized.

Jan 1, 1976

By Qingyun Huang, Junyi Xiang, Xuewei Lv, Chenguang Bai

The extraction of vanadium from mechanically activated converter slag was studied in dilute sulfuric acid solution. The effects of roasting and leaching parameters were investigated. The results show that Ca/V mole ratio, roasting temperature, leaching temperature, liquid-solid ratio, and particle size all have significant effects on vanadium leaching efficiency from calcification-roasted converter slag.

Mar 1, 2017

By R. H. Rubisov

Sulphuric acid pressure leaching of nickeliferous laterites has attracted considerable attention from the nickel industry during the past five years. The process is especially advantageous for limonitic laterites that mostly contain goethite, because iron precipitates releasing acid and thus rendering low acid consumption. It is also applicable to mixtures of limonites and saprolites, although at higher acid consumption due to magnesium. Effective process design requires the solubility of metals that precipitate during the process to be known. In the present work, determination of metal solubilities is based on a simple speciation program that assumes the presence of only one dominant complex for each metal. The thermodynamic data for the precipitation reactions are extracted from high-temperature experiments with monometallic systems published previously. The validity of the approach is then tested against mixed bimetallic systems, and finally applied to calculate the solubility of aluminium, iron and magnesium in laterite leaching effluents "at temperature". In both cases of limonitic feed and limoniticfsaprolitic blends, the prediction closely follows metal solubilities measured experimentally at temperatures from 230 to 270°C and at terminal he acidities ranging from 10 to 75 g/L.

Jan 1, 1999