Search Documents

By Lucas Gonçalves Generoso, Larissa Rodrigues de Carvalho Rocha, Gerson Evaristo de Paula Júnior, Beatriz Fausta Gandra

A eficiência na redução dos minérios de ferro no alto-forno é governada pela estrutura e permeabilidade das camadas de carga. A zona granular do alto-forno é a região onde a carga mantém a sua estrutura estratificada, decorrente do carregamento, sob a forma de grãos sólidos. Nessa região, as condições de permeabilidade determinam o perfil de distribuição do gás e, consequentemente, a eficiência térmica e química do reator. Na Usiminas, foi desenvolvido um ensaio de permeabilidade que permite avaliar a perda de carga em leitos formados pelas matérias-primas utilizadas nos altos-fornos, buscando as condições mais favoráveis ao fluxo gasoso. A partir deste ensaio, foi possível avaliar cargas compostas exclusivamente por sínter, pelota ou minério granulado, ou ainda combinações binárias entre estes. O sínter apresentou a maior perda de carga, seguido da pelota e do minério granulado. Apesar disso, o sínter foi o material que permitiu maior acréscimo de vazão do gás. Os ensaios realizados indicaram que 5% de material com granulometria menor que 5 mm é o limite para a concentração de finos do sínter, situação em que foi observado acréscimo de aproximadamente 50% na resistência à passagem dos gases para as velocidades correspondentes àquelas dos altos-fornos. O leito de melhor permeabilidade foi formado por 95% de sínter e 5% de pelota, seguido pelo de 100% de sínter, sem diferença significativa entre essas condições. Em geral, a combinação de sínter e pelota é mais benéfica para a permeabilidade do leito.

Oct 1, 2019

By Maria Olivia de Barros Almeida

O intuito do presente trabalho é identificar, dentre as proporções entre resina e catalisador analisadas cineticamente, a melhor condição de cura. O mecanismo de cura das resinas epóxi é um dos mais estudados e a técnica mais utilizada no estudo deste comportamento é a calorimetria exploratória diferencial (DSC). Neste trabalho, foi utilizado o equipamento DSC 1, fabricada pela Mettler Toledo, pelo método dinâmico. Por meio da técnica de DSC, pode-se observar perfis de cura, temperatura de transição vítrea e a determinação das melhores condições de preparação de compósitos. A reação de cura de resinas termofixas é um processo complexo, definido como uma mudança irreversível nas propriedades químicas e físicas por uma reação química. Estabelecendo-se as condições ideais de cura, a resina epoxi resulta em uma estrutura rígida altamente reticulada, a qual combina as excelentes propriedades térmicas, mecânicas, resistência química.

Aug 17, 2017

By Hana Livia Frota Coelho

Durante a laminação a quente a superfície de aço é exposta ao ar e água, sendo esta última utilizada para controlar a temperatura dos rolos e/ou a taxa de refrigeração do aço. Esta exposição leva à formação de uma camada de óxido na superfície das barras, que pode facilitar ou dificultar a corrosão, servindo como uma barreira ou como um caminho para íons presentes na atmosfera e, além disso, causar modificações nas propriedades mecânicas. O objetivo do presente estudo é avaliar o efeito do processo de resfriamento após laminação a quente sobre o desempenho de vergalhões de aço microligado frente a propriedades mecânicas e a formação da camada de óxidos. Os vegalhões produzidos com diferentes métodos de resfriamento tiveram análise de microestrutura, tração, microdureza, dobramento, espessura da carepa formada, análise de corrosão e foram expostos à atmosfera. O progresso da corrosão foi avaliado pela observação visual do produto de corrosão formado sobre a superfície das barras. A morfologia da camada de óxido após o processo de laminação foi estudada por microscopia eletrônica de varredura (MEV). As amostras que tiveram uma taxa de resfriamento maior, 63%P e 100%P, tiveram também um aumento nas propriedades mecânicas. A amostra 100%P foi a que obteve melhor comportamento frente ao ensaio de corrosão. Além disso, verificou-se que a camada de óxido inicial nas barras de aço, que são relacionados com o processo de fabricação, possuiam aderência diferente ao vergalhão, sendo a melhor condição observada nas amostras 63%P e 100%P.

Oct 30, 2017

By Andressa Pereira dos Reis Croucillo

O desenvolvimento de impressoras 3D permitiu uma maior produção de peças e próteses médicas provenientes de polímeros termoplásticos como PLA e ABS, para produção de filamentos. Este trabalho avaliou as características mecânicas de próteses impressas, em determinada temperatura, de filamento PLA. Foram impressos diversos corpos de provas, para a realização de testes de tração, verificando que a configuração com densidade 100%, espessura de 0,4 mm e direção de impressão de 45° e 135° apresentou melhor resultado de resistência mecânica. Realizaram-se também, simulações matemáticas para análise de resistência à queda e flambagem. O conjunto de testes físicos e matemáticos determinou que o PLA não atendeu os requisitos para aplicação deste como próteses.

Oct 30, 2017

By Giancarlo Alfonso Lovón Canchumani

A indústria da mineração do ferro brasileira ocupa posição relevante no cenário mundial, exportando para os principais mercados consumidores os produtos beneficiados. Esta indústria de beneficiamento tem consumo elevado de recursos e de energia, o que consequentemente gera grandes quantidades de emissões gasosas, líquidas e sólidas, contaminantes do meio ambiente. Nesse contexto o presente artigo tem por objetivo avaliar o ciclo de vida da produção de pelotas de minério de ferro, através da identificação dos impactos ambientais gerados nas etapas de lavra, beneficiamento, transporte e pelotização, com o intuito de dar subsídios a medidas mitigadoras. Foi realizado um estudo de caso em uma empresa de produção de pelotas de minério de ferro e utilizando a metodologia de Avaliação do Ciclo de Vida, baseado na norma ISO 14040. De acordo com os resultados obtidos os impactos ambientais mais importantes em relação ao ciclo de vida da produção de pelota, são referentes à categoria de depleção dos recursos minerais com 64,4% do total ponderado e a emissão de particulados no processo de lavra, que monta a 28,6% do mesmo total. Enquanto a fase com maior contribuição para o impacto total para a produção da pelota é a de beneficiamento.

Aug 16, 2017

By Everaldo Afonso Fernandes

O presente trabalho foi realizado com a finalidade de estudar o efeito dos elementos titânio (teor de 0,05%) e de níquel (teor de 0,03%) na liga Al-0,05%Cu-[0,24-0,28] %Fe-0,7%Si para fins de transmissão e distribuição de energia elétrica. Dessa forma, foi adotada uma sequência operacional a fim de caracterizar as estruturas apresentadas pelas ligas. Os processos de solidificação foram realizados via coquilha de aço (forma de “U”). Depois de solidificadas as ligas, os lingotes passaram pelos processos mecânicos de usinagem e laminação para obtenção de corpos de prova com quatro distintos diâmetros (2,7; 3,0; 3,8; 4,0) mm a fim de aproximar estes das bitolas utilizadas em indústrias de cabos elétricos. Todas as ligas foram caracterizadas macroestruturalmente analisando as estruturas brutas de fusão, eletromecanicamente por meio do ensaio de tração [?] e condutividade elétrica [%IACS]. Posteriormente, para a melhor compreensão dos resultados foram avaliados os valores de alongamento [?%] indicando que o diâmetro 3,00mm é a modificação com 0,05%Ti foram os de melhor resultados apresentados.

Aug 7, 2018

By Bernardo de Oliveira Costa

O tempo de mistura em panelas de aciaria foi avaliado em diversos trabalhos através de modelamento físico e matemático. A maioria destes trabalhos está focada em analisar os efeitos da vazão de gás e localização dos plugs porosos usados para injeção. Em artigos recentes, o uso de dois plugs de injeção foi investigado, mas ainda há uma controvérsia significativa sobre a melhor posição para injeção de gás. Nestes artigos, a vazão de gás é distribuída igualmente entre os dois plugs de injeção. Neste trabalho, foi feito modelamento físico para avaliar os tempos de mistura de panelas de aciaria equipadas com dois plugs porosos. O modelo físico foi construído na escala de 1:5 de uma panela de 170 toneladas usada em uma planta brasileira. Os tempos de mistura foram apurados usando a injeção de um traçador. Diferentes combinações de posição dos plugs porosos e distribuição da vazão de gás foram ensaiadas. Experimentos de visualização do escoamento também foram desenvolvidos utilizando tufts e injeção de corante. Estes experimentos foram úteis para análise dos resultados.

Jul 30, 2018

By Victor Freire de Oliveira

A exaustão das reservas mundiais de minérios de ferro de qualidade, bem como o progressivo avanço das legislações ambientais, são tendências que têm motivado pesquisas acerca do uso de resíduos ricos em ferro e carbono para a fabricação de sínter metalúrgico para uso em alto-forno. Para tal, é necessário que se verifique o comportamento desses materiais nas condições termodinâmicas e cinéticas do processo de sinterização, bem como o seu efeito sobre a qualidade do sínter e sobre os parâmetros de processo da sinterização. Com esse objetivo, em uma primeira etapa do presente projeto de pesquisa, misturas representativas da prática operacional das usinas brasileiras, bem como misturas visando à maximização da reciclagem de resíduos foram testadas em laboratório em condições próximas às da sinterização. Os resultados de análises químicas e mineralógicas obtidos experimentalmente foram comparados com predições termodinâmicas de um modelo de equilíbrio multicomponente, havendo concordância satisfatória.

Oct 30, 2017

By Leticia Costa Macêdo

Esse trabalho tem como objetivo analisar por meio da termodinâmica computacional a influência do K2O na dissolução das fases sólidas formadas durante o processo de dessulfuração de ferro gusa. Para isso, foi utilizada a cal como agente dessulfurante e a Sodalita (Fonólio) como fundente, realizando uma adição de K2O no fluxante de 1% a 10%, com uma temperatura de trabalho de 1400ºC. Por meio do uso de software de termodinâmica computacional FactSage, foi possível simular e avaliar as fases sólidas e líquidas formadas na temperatura determinada e comparar com os resultados obtidos com outras análises. Os resultados obtidos mostraram que o aumento gradativo de K2O levam a um aumento do potencial termodinâmico de dessulfuração e melhores condições cinéticas, sendo a mistura que apresentou os melhores resultados a que continha 10% de sodalita com adição de 10% de K2O na fonte.

Oct 30, 2017

By H. M. Smith

MORE than a year before the United States entered World War II, the requirements of the National Defense Program indicated the need for additional sources of aviation gasoline. On September 10, 1940, Dr. R. E. Wilson, Group Executive, Advisory Commission of the Council for National Defense, requested the Bureau of Mines to undertake a survey of crude oils of the United States to designate those suitable for the production of 91-octane aviation gasoline. As quickly as a program could be defined, agreed upon, and funds provided to conduct the work, the Bureau began the project. Over a period of many years the Bureau had collected samples and made analyses of thousands of crude oils produced in the United States. Although these analyses did not include octane numbers of the gasoline fraction, they provided data necessary for calculating the correlation index. This index, developed within the Bureau, is a measure of the types of hydrocarbons present in gasoline and therefore is roughly indicative of the octane value. This fund of information from Bureau of Mines Hempel analyses, supplemented by information obtained from oil companies, reduced considerably the necessary laboratory work by providing data that permitted a large number of crude oils to be eliminated from consideration. However, in the survey carried out during the last part of 1940 and the first half of 1941, 225 samples of crude oil were collected and distilled. Octane values of the distillates were determined by the Army AFD-1C method. (See page 57.) A report containing these results, together with the calculated amounts of 91-octane aviation gasoline available from these sources, was prepared and distributed to the several offices of the Office of the Petroleum Coordinator for National Defense in August 1941. In December 1942 the Office of the Petroleum Coordinator for National Defense became the Petroleum Administration for War (P. A. W.).

Jan 1, 1951

By S. Beskri, N. Geoffroy

When metallurgical plants are designed, a lot of consideration is almost always given to material selection and possible damage mechanisms. Materials engineers are generally involved and will strive to select optimal alloys or refractories for the design conditions. Once in operation however, things often change. Equipment is overstressed to increase production, corrosive leaks are not always promptly addressed, proper welding procedures are disregarded, etc. This paper describes various cases from the mining and metals industry where serious mishaps, associated consequences, and costs could have been avoided if simple and proactive steps had been taken. It also presents a strategy, based on safety reviews, to help predict and prevent damage to critical pieces of equipment.

Jan 1, 2015

By R. J. Miller

Rock strata, natural and mining-induced stresses, and structural features can combine to create dangerous instabilities in or around longwall panels. Rock noises and properties variations associated with local stress systems can be used to characterize developing instabilities. Through a learning process at a particular mine, guidelines can be developed to allow the determination of relative risk and timing of a potentially disastrous instability. Once a dangerous instability has been identified, operational modifications can be employed to get through the instability, or active measures such as destressing can be used to mitigate the instability. This paper will discuss how an integrated monitoring system and associated data processing can be used to develop a hazard prediction capability for a longwall mine.

Jan 1, 1996

By Erika Moonin, Jim Nickerson, Marcus Jensen

"This paper will explain how the Contractor and Owner avoided a contractual dispute involving characterization, impacts, and final remedy for challenging ground conditions encountered during drill and blast excavation of the starter tunnel required for launch of the tunnel boring machine (TBM). During excavation more than 600 feet underground, the Contractor encountered a large complex fault zone subject to more than 14 bar of water pressure. Successive ground inflows from the fault complex over a six-month period presented significant technical and partnership challenges for the team and ultimately delayed the project by nearly one year. This paper will discuss how the Contractor, Owner, and their respective consultants worked together to address these challenges, make decisions, and ultimately move the project to successful completion. PROJECT BACKGROUND AND NEED Seven states of the western United States of America rely heavily on the Colorado River and its tributaries for their water supply. The primary source of water for the Colorado River is winter snow that falls in the mountains ringing the Colorado River basin, including the Rocky Mountains, the Wind River Mountains, and the Uinta Mountains. Flows in the Colorado River vary significantly from year to year, depending on the amount of snow and rain deposited in the basin. During the 1980s and 1990s, snowfall was relatively abundant and Colorado River flows were high on average. Beginning in the year 2000 and continuing to the present day, snowfall has been well below documented historical averages and Colorado River flows have diminished. In fact, a trend toward diminishing flows is evident during the period of the historical record. This variability in Colorado River flows and the trend to lower flows is represented in the following Figure 1."

Jan 1, 2016

By Patricia Pride, Kurt Bettger, Jack Raymer

"INTRODUCTION The Jefferson Barracks Tunnel is in the final stages of design and is expected to go out to bid in the summer of 2016. The project is located in south St. Louis County along the west bank of the Mississippi River, about 13 km downstream of the St. Louis Gateway Arch. The project consists of a deep sanitary sewer tunnel, a deep pump station and several intakes. The intakes will divert sanitary flows into the tunnel and the tunnel will convey the flows by gravity to the Lemay No. 3 Pump Station, which will pump them up into the Lemay Waste Water Treatment Plant. The tunnel is about 5.4 km long and will be lined with 84-inch (2.1 m) fiberglass pipe. It drops at a gradient of 0.1 percent from south to north and will be bored through strong limestone using a hard-rock tunnel boring machine (TBM). The diameter of the TBM is anticipated to be about 3.4 m. The Owner’s original concept was for a relatively shallow tunnel so as to minimize construction and pumping costs. The preferred alignment ran close to the river, next to the existing force main, which was to be abandoned. Keeping the tunnel close to the force main would reduce the amount of shallow sewer work needed to connect the existing feeder sewers to the new tunnel. Several geotechnical investigations were performed, with shallowly focused geophysics and the borings all going exactly down the conceptual tunnel depth. Limestone bluffs run along the Missouri side of the river. These bluffs are pockmarked by sinkholes and riddled with karst. Large, well-known caves occur both north and south of the alignment. Karst features, including deep crevices and possible caves, were found in those early geotechnical investigations. Many of these features extended well below the level of the Mississippi River and would have been encountered by the tunnel. If a large crevice or cave were encountered, then the inflow of mud and water into the tunnel could have been large and possibly uncontrollable. Something had to be done to mitigate this situation. Pre-excavation grouting was considered, but the program would have been huge and extremely expensive. Using a closed-face TBM with bolted and gasketed lining was also considered, but that too was both risky and extremely expensive. The Owner could have abandoned the tunnel altogether and built a new force main, but that would have brought a whole new set of problems and was undesirable to the Owner. The last option was to move the tunnel away from the karst."

Jan 1, 2016

By Ronald D. Jacksha, Jason B. Coder

Wireless technologies are becoming vitally important for modern mining operations. Used for increasingly complex tasks — such as miner and asset tracking, proximity detection, teleremote and autonomous equipment operation, and environmental monitoring — the ability of wireless systems to perform their intended functions satisfactorily in the presence of other wireless systems (coexist) is critical not only to the successful operation of modern mines but also to the safety and health of mine workers. Concerns regarding the ability of wireless systems to coexist can often hinder the decisionmaking process for adopting technologically advanced wireless systems. However, with adequate knowledge of the concepts of coexistence and appropriate wireless system management, coexistence concerns do not need to be an impediment to the successful adoption of wireless systems. There are several common wireless coexistence-related fears that can inhibit adoption of wireless technology: fears that safety-related systems may not operate properly when needed, failures could disrupt production, and wireless systems may inherently require costly troubleshooting. Most of these fears can be alleviated through proactive activities.

Apr 1, 2026

By Sam Warren, Antonio Marinucci, Genesis Z. Figueroa, Anne Lemnitzer

Drilled Displacement Piles (DDP) provide an ideal deep foundation solution that combines the benefits of ground improvement with traditional advantages of piling systems. This paper consolidates data from 20 construction projects in which more than 30 DDPs were installed and tested axially. High quality site exploration data (e.g., Cone Penetration Test and Standard Penetration Test) were evaluated to derive geotechnical analysis parameters. The test sites consisted of mostly mixed soil types with strongly stratified layers of sand, silt, and clay. Pile diameters ranged between 40 cm and 61 cm. Test results were compared with predictive methods developed specifically for DDPs as well as methods used in general geotechnical practice. The accuracy of the empirical methods is presented in terms of total pile capacity, pile length/diameter, and soil type. The large majority of all examined methods underpredict the in-situ pile capacities. It was also found that the difference between the tested and predicted capacity is strongly related to the level of improvement in the surrounding soil due to the piles’ installation. A general comparison between predictive axial accuracy and the observed level of ground improvement upon installation is also discussed.

May 1, 2022

By Paul C. Hagan, Jianhang Chen, Serkan Saydam

"Modified cable bolts are commonly used in underground mines due to their superior performance in preventing bed separation when compared with plain strands. To better test the axial performance of a wide range of cable bolts, a new Laboratory Short Encapsulation Pull Test (LSEPT) facility was developed. The facility simulates the interaction between cable bolts and surrounding rock mass, using artificial rock cylinders with a diameter of 300 mm in which the cable bolt is grouted. Furthermore, the joint where the load is applied is left unconstrained to allow shear slippage at the cable/grout or grout/ rock interface. Based on this apparatus, a series of pull tests were undertaken using the MW9 modified bulb cable bolt. Various parameters including embedment length, test material strength and borehole size were evaluated. It was found that within a limited range of 360 mm, there is a linear relationship between the maximum bearing capacity of the cable bolt and embedment length. Beyond 360 mm, the peak capacity continues to rise but with a much lower slope. When the MW9 cable bolt was grouted in a weak test material, failure always took place along the grout/ rock interface. Interestingly, increasing the borehole diameter from 42 mm to 52 mm in weak test material altered the failure mode from grout/rock interface to cable/grout interface and improved the performance in terms of both peak and residual capacity.INTRODUCTIONFully grouted cable bolts have been used in underground mining industry for many decades. Initially, plain cable bolts manufactured by winding seven flexible steel wires together were commonly used (Thorne and Muller, 1964). Laboratory and field tests lead to a better understanding of the transfer process between grouted cable bolts and the surrounding rock mass, which is beneficial to improve the reinforcing performance of cable bolts in engineering practice (Fuller and Cox, 1975; Cox and Fuller, 1977; Schmuck, 1979; Stillborg, 1984). Nevertheless, as in many cases the initial cable was sourced from discarded steel with a smooth surface along the strand, plain cable bolts did not always meet performance expectations (Windsor, 1992). Over time, it was realised that cable surface geometry plays an important role in determining anchorage performance. Consequently, modified forms of cable bolts were developed. For instance, twin-strands which were made by using spacers to combine two plain cables together improved anchorage capacity two-fold (Matthews, Tillmann and Worotnicki, 1983). However, this required a large borehole to be drilled. Epoxycoated strands had remarkable performance in practice but were difficult to install without damaging the epoxy layer (Dorsten, Hunt and Kent, 1984). In the 1990s, there was a rapid development in the cable bolt design. A typical example was birdcaged cable bolts. They were initially suggested by Hutchins et al. (1990) via unwrapping traditional seven-wire strands and generating a number of nodes together with antinodes along the strand. But it was difficult to make birdcaged cable bolts that could be coiled for transporting."

Jan 1, 2015

By G. W. Thompson

G. W. THOMPSON,* Brooklyn, N. Y.-This subject has two aspects, neither of-which can be ignored: these are the economic aspect and the technical aspect. Under ordinary conditions, economic law will take care of the conservation of tin. Under present conditions it seems desirable that economic law should still be permitted to operate as far as is practicable. It is true that this law operates rather slowly, and that under war conditions it cannot be depended upon to give our Government the supply it immediately needs. There should, therefore, be a designation of the essential industries by the Government, and tin should be supplied for those needs, letting the non-essential industries take what is left. At the same time, information ought to be forthcoming as to how tin can be conserved; with tin selling at 80 c. per pound, more or less, it is to the interest of every consumer to get the best information he can as to how he can save tin. Economic law would properly punish those who do not study their own interests in this way. I deprecate, therefore, any centralized socialistic effort toward avoiding penalties through failure to observe and obey economic law. In saying this, however, I am not unmindful that it is desirable for our Government to take such control of the tin situation as may be necessary to the prosecution of the war, practically regardless of the effect of such action upon individual industry, which should studiously seek to adjust itself to the new condition. The Government should promulgate such technical information as it can collect, showing how tin can be conserved, and should urge upon every consumer the exercise of his common sense in self-protection. There is very little danger of any one attempting to hoard or corner tin, in the present state of the market. Most consumers will be glad to live from hand to mouth, covering their sales by purchases, or vice versa. As to the technical aspects: Tin and tin alloys are used to give certain practical and also certain artistic results. The practical factors are those involved in proper adhesion, continuity of surface, protection, the right degree of hardness, proper working qualities, etc. The artistic results are those that appeal purely to the eye or to our cultivated sense of what is desirable. There is no doubt that a great deal of tin could be saved if there were not a demand for certain pleasing effects. How can this saving be brought about? The users of tin hearing alloys are not the only ones involved in this question. The manufacturers of solder and babbitt have for a long time sought to give certain appearances to their fabricated bars and ingots in order to make them more salable. The user of a solder is very apt to judge of its working qualities by the appearance of the bar; the same thing is true with regard to babbitts. Under ordinary conditions, manufacturers are justified in trying to

Jan 12, 1918

By Fabiola Espinoza Carmona, Elena Chiriotti, Edoardo Misano

"INTRODUCTION Ganntas Tunnel is part of the modernization project of the railway between Alger and Oran, in Algeria. In order to double and rectify the existing line between El Affroun and Khémis Miliana, the alignment foresees the excavation of a 7 km-long twin tunnel. The excavation works started in June 2011 with the contractor CCECC, under the supervision of SYSTRA. Excavation is driven in conventional method by hydraulic hammer simultaneously on 8 different faces since excavation was started also from a junction window towards the middle of the tunnel. The minimum longitudinal distance to be respected between two contiguous tunnel faces has been set to 30 m. The tunnel cross-section is a 70 m² oval shaped profile, temporary support consists of shotcrete, bolts and steel ribs. A 30 to 50 cm thick cast in situ concrete final lining has been provided as well. When the tunnel reached a fault zone in soft clayey marls extreme squeezing occurred, works were stopped and re-profiling operations were carried out along more than 100 m. To date, works proceed at slow rate since high convergences are still monitored and completion of works is not expected before December 2016.GEOLOGY The project is located within the Tellian Atlas mountain area, including in particular the Djebel Ganntas massif in between Mitidja and Chleff plains. Djebel Ganntas is characterized by an extensive massif aligned in East-West direction with smooth slopes made of soft clays that emerge in multiple cliffs and ravines. On the top of it, along the edge, a more recent sandstone formation is found. The existing data on the geology did not allow to establish an accurate geological model at tender stage. In-situ investigations allowed at design stage to identify a Quaternary alluvial cover of clays and gravel, followed by a Miocene stratum divided in a sandy top layer and a lower clayey layer. From a structural point of view, geological maps suggest a north direction dip of layers, but the in situ surveys showed that layers were highly folded. The lack of information at tender stage on the structure of the geological series should have triggered an extensive investigation campaign at detailed design stage which did not take place causing serious consequences on costs and time at construction stage."

Jan 1, 2016

By D. F. Malan, P. J. Le Roux

Almost no work has been published on the strength of pillars in mines exploiting the LG6/LG6A chromitite bands in the Western Bushveld Complex. The strength of these pillars is unknown, and the hard rock industry still uses the Hedley and Grant formula. Numerical modelling, using inelastic constitutive models, may be of some value in estimating the pillar strength, but this approach is difficult and prone to errors as many assumptions are made. This paper explores the alternative approach of the back-analysis of actual LG6/LG6A mining layouts, using displacement discontinuity codes to simulate the average pillar stresses on a mine-wide scale. From this, and underground observations, a ‘minimum’ pillar strength (K-value in the pillar strength formula) can be estimated. The codes TEXAN and Map3D are both used in the paper to simulate the actual pillar shapes and sizes in an LG6/LG6A mine. The results are encouraging as the two codes produced similar APS values for a complex pillar geometry. An estimated K-value of 77 MPa was determined for the LG6/LG6A pillars in this particular area. This is more or less similar to earlier work done for the UG2 chromitite seam, but higher than the K-value of 39 MPa for a linear formula obtained by other workers for LG6/LG6A pillars. Caution should therefore be exercised before using this higher value for all areas. The effect of element sizes and explicitly simulating the effect of the surface for shallow pillars is illustrated in the manuscript using both codes. The need for actual pillar observations and an iterative design process, which cycles between modelling and observations, is also emphasized.

Nov 27, 2024