Search Documents

By Leiting Yue, Peng Ren, Yu Shen, Zhihong Liu, Haibao Shao, Longgong Xia, Feng Yu

The Kennecott-Outotec Flash Converting technology has been proven as an advanced and mature process in 5 individual plants during the past 2 decades. High grade copper matte (65–72%) produced in the flash smelting, or other smelting technologies is granulated to 3-5mm granules in a water torrent, and further crushed to fine powder (≈50µm) and dried to contain less than 0.3% H2O. Oxygen enriched air, together with fine copper matte powder and lime flux are injected into the reaction shaft by a matte burner. The copper making and slag making reactions will happen in very short time and distance during the particle falling and settling. However, industrial practice has found negative effects caused by sodium contamination. Na is introduced in the copper matte granulating process, and appears as Na2SO4 on particle surface. When Na content was high, scaling problems in the boiler will be worse, and the processing air will be blocked by the growing accretion around the matte burner, and as-produced blister copper is always high in S and O. In this present study, an industrial matte sample was used in the experimental work. Na was introduced into the matte powder by Na2SO4 solution soaking. The burning behaviour of the doped copper matte powder has been investigated as a function of the impurity concentration and processing temperature. Morphology and composition of these samples explained how Na2SO4 converts and reacts in the oxidizing atmosphere, and how they or their converting species influence the burning behaviour of matte particles. Cross-sections of as-prepared samples were analyzed with SEM-EDS, and the reaction mechanism has been carefully interpreted. Results from the present study can benefit both academic and industrial people. INTRODUCTION "Flash Converting" technology was developed jointly by Kennecott Utah Copper Smelter and Outotec (Finland) OY in 1992. The first industrialization of the technology was in Utah Smelter in 1995. Since 2006, it has been successfully applied in Xiangguang Copper, Tongling Jinguan Copper Branch, Fangchengang Jinchuan Copper, and Ningde Southeast Copper. The technology has also been further developed in those smelters. At present, roughly 2 million tons blister copper is produced annually through the Kennecott-Outotec Flash Converting technology, accounting for more than 10% of global primary copper production. The technology has advantages of high efficiency, high sulfur capture rate, good in environmental issues, mature equipment supporting, high automatic control level, low comprehensive energy consumption and flexible connection with the smelting unit, which make the technology to be one of the best choices in investing a new large-scale copper smelter or updating an old copper project in the world.

Jan 1, 2019

By G W. Wilson

Net solar radiation is one of the key factors affecting evaporation from soil covers on waste rock dumps. While net solar radiation is normally taken as a uniform parameter over a site for modelling purposes, there can be significant variation in the radiation actually received on various portions of the dump. These variations are a function of the difference in the cover slope and direction of exposure. A predictive model has been developed to calculate the actual radiation received on the dump surfaces, based on the net radiation data measured at a weather station on a horizontal surface. The model has been designed for application at any mine site in the world, and can be used in conjunction with evaporative flux models to help estimate the effect of three-dimensional variations in the cover surface exposure. The waste rock dump at Equity Silver site (located in British Columbia, Canada) has a barrier-type soil cover system to limit oxygen entry and water infiltration. This cover has been monitored for the past nine years. The new net solar radiation model has been applied to this site and the predicted net radiation was compared to the values of actual net radiation measured on the site. The predicted variations in net radiation over the three-dimensional surface of the waste rock dump have been applied to calculate spatial variations in potential and actual evaporation (or evapotranspiration) from the site. Preliminary analyses indicate actual evaporation from a site at this latitude could vary by a factor of two for exposed versus shaded slopes. The implications of these variations for the site are considered.

Jan 1, 2003

By M. Mpofu, B. Maphalala, S. Khan, S. Ngobese, D. Roberts

This paper details an assessment of stemming practices at a South African opencast coal mine and their influence on ground vibration and air blast. Quantitative and qualitative analysis methods were used for the study. The parameters assessed for the quantitative analyses included stemming length, stemming material type, blast-hole depth, burden, and spacing. Pre-blast data from the mine was analysed to determine the deviation between actual and mine design stemming parameters. Mine design stemming length was also compared to the rule-of-thumb stemming lengths. Peak particle velocity (ground vibration) and air blast data from seismograph stations around the mine was analysed to determine the correlation between stemming length and excessive ground vibration and air blast. The qualitative analysis involved observations of blasting procedures at the mine to determine compliance with mine procedures. Some level of non-compliance of actual stemming parameters to design stemming parameters was found, which initially suggested that non-compliance may have contributed to excessive air blast. However, further analysis of the seismograph results indicated no direct correlation between stemming length and excessive air blast and ground vibration. Since stemming parameters are interrelated, it is crucial that all blasting procedures, including stemming, are executed in accordance with best practice, and recorded accurately. There is a need for digital systems for capturing on-bench blasting parameters, as the currently used manual data recording and reporting systems are inefficient and prone to error. Improvements to blast designs are possible through efficient and accurate data recording and reporting systems.

Jan 1, 2021

By HASAN SERKAN GOKCEN, SERKAN CAYIRLI

Manufacturers have improved various stirred mill types to be well adapted to fine and ultrafine grinding applications. These stirred mills, which are operated in wet or dry conditions, may be classified as horizontal — such as AHM-horizontal agitated media mill, IsaMill and Drais mill — or vertical — such as tower mill, Vertimill, Maxmill, Stirred Media Detritor and ATR vertical agitated media mill. The main difference between vertical and horizontal structures is in their operational variations. Additionally, the scaling-up of mills is also an important parameter for selecting the suitable orientation [1]. The purpose of this study was to investigate the dry grindability of calcite powders in a vertically and horizontally orientable laboratory batch-type stirred mill. The experimental results were evaluated using stress intensity analysis. The results showed that the d50 values decreased with increasing stress energy down to a certain point and then increased for both milling orientations. Even though the optimum stress energies for both vertical and horizontal orientations were in the range of 1 × 10−3 to 5 × 10−3 Nm at 750 and 1,500 kJ/kg energy consumption, the product size was finer for the horizontal orientation at the same stress energy value.

By HASAN SERKAN GOKCEN, SERKAN CAYIRLI

The purpose of this study was to investigate the dry grindability of calcite powders in a vertically and horizontally orientable laboratory batch type stirred mill. The experimental results were evaluated using stress intensity analysis. The performance was also compared in terms of mill orientation. The results showed that the d50 values decreased with increasing stress energy down to a certain point and then increased for both milling orientations. Even though the optimum stress energies for both vertical and horizontal orientations were in the range of 1*10−3 to 5*10−3 Nm at 750 and 1500 kJ/kg energy consumption, the product size was finer for the horizontal orientation at the same stress energy value. Additionally, to the best of the authors’ knowledge, this is the first study to compare mill orientation (vertical vs. horizontal) for the same mill and under the same test conditions.

Apr 21, 2021

By Angus D. Campbell

"IntroductionThe subject assigned to me tonight gives unlimited scope. The material available is so voluminous and leads into so many ramifications, and the memories of the Camp are so vivid and treasured, that it is difficult to decide just what to use. Then, too, the geologists are the story-tellers of our tribe - I am only a hard rock miner.Members of the Cobalt Branch and Cobalters everywhere will agree without question that this Cobalt camp has been the greatest of all influences on Canadian mining. To those who do not know Cobalt, our opinion may seem prejudiced and our statement exaggerated.Be that as it may, discussion on this subject can be profitable, since it is worthwhile now and then to think on 'whence we came' and 'where we are going'.In the revival of interest in the Cobalt camp, we hope our guests may feel some of the old Cobalt Spirit, which has become the Spirit of the North.Visitors may even, while here, catch a glimpse of that whimsical little guardian spirit of the camp - the original goblin, the Kobold - for which Cobalt was named.While Kobold brings that good luck which plays so important a part in mining, he can have his evil moments, as in his original German home. There, when he made the silver disappear from their good ore, they cursed the grey ore, calling it Kobold.Although this little goblin bas frequently upset our best mining plans and geological calculations, be has played the game as well. He placed •some silver on the surface, and when he hid ~t at depth he left dues .for its finding. He has rewarded many who sought his treasure and is still rewarding those who have persevered and had faith in him. t:lis influence and that of Cobalt camp has probably had a greater influence on your work and your mining areas than you realize"

Jan 1, 1950

By Lionel Loïc Limol

Polymeric materials, such as polyurethanes and rubbers, are widely used in the mining industry because of their moderate cost and excellent mechanical properties. Such polymers have been used mainly in transportation (conveyor belt systems and pipes coatings) and screening, for their appreciable abrasion wear resistance. Studies revealed the complex influence of test parameters, such as grit size and applied normal load, on the abrasion wear process for polymers. In this study, the abrasive wear behavior of several polyurethanes and rubbers were investigated at room temperature according to a rotary drum abrasion method (DIN 53516). Wear tests were carried out at 26 cm/s test speed and load value of 5 N and 10 N. Corundum paper grit varying from 60 to 400 mesh were used as an abrasive surface. After each test the mass loss of the pin was recorded and the wear rates were calculated from wear volume. The wear surfaces were investigated by scanning electron microscopy.

Jul 31, 2018

By C B. Valentin

It is acknowledged that the analysis of iron ores using X-ray fluorescence (XRF) for major and minor elements is best carried out on fusion discs. This method of sample preparation eliminates mineral and particle size effects which can lead to biased results when using pressed powder pellets. However, the fusion disc method is costly as it requires a high capital investment in platinumware, requires experienced operators and uses expensive fluxes. Also, the dilution effect complicates the analysis of trace elements. For many applications, such as exploration and mining control, the method of XRF analysis of iron ores by pressed powder pellet probably provides data of adequate quality. Kumba Iron Ore, an iron ore producer in South Africa, recognises this and carries out most analyses of iron ore by pressed powder pellet and uses the automated fusion method mainly for certification of in-house calibration standards and quality control (QC) samples that are used for validation of pressed powder pellet method purposes. Automated fusion is also used for analysing the composite export shipping samples. All the other exploration, production, despatching and plant operation samples are done by the pressed powder pellet method. Automation of sample preparation procedures should improve the quality of data for pressed powder pellets. To compare the precision of the three methods of sample preparation and XRF analysis, 20 aliquots of a QC standard were prepared and analysed by each procedure/preparation method. The results and statistical data on the most important elements, Fe, K2O and P, are as shown later in Table 2.Clearly the precision is best for the auto prepared fusion discs, as expected, and worst for the manually prepared pressed powder pellets. However, the data generated from the auto prepared pressed powder pellets compare remarkably well against those from the auto prepared fusion discs.

Jan 1, 2007

Discussion of the paper of Robert R. Abbott, presented at the New York Meeting, October, 1913, and printed in Bulletin No. 82, October, 1913, pp. 2389 to 2400. ALBERT SAUVEUR, Cambridge, Mass.:-Mr. Abbott has certainly made a strenuous effort to ascertain the influence of the various elements on the absorption of carbon by steel-a subject of great importance to those dealing with the case hardening of that metal. Because of the extensive and careful character of Mr. Abbott's experiments, one is all the more disappointed that his results, as he himself recognizes, are not more satisfactory; for, indeed they leave us just about where we were,-still entertaining uncertain views in regard to the carbon-absorbing power of various alloy steels. It might be asked whether Mr. Abbott's method of estimating the amount of carbon absorbed-namely, by weighing the specimens before and after the carburizing treatment-was the best one to select. Are not serious sources of error. inherent to such procedure because of the difficulty of satisfactorily removing the earburizing material attached to the specimen ? The method of least squares has certainly failed to solve the problem satisfactorily. By manipulating Mr. Abbott's results in a different manner I have obtained the following expression: P = 100 - 50 C - 7 Ni + 20 Cr, in which P represents the carbon-absorbing power; C, the percentage of carbon; Ni, that of nickel; and Cr, that of chromium. It is assumed that the carbon-absorbing power of pure iron, or what might be called its carburizability, is represented by 100. Applying the formula, for instance, to a steel containing 0.15 per cent. C, 3 per cent. nickel, and 0.50 per cent. chromium, its carbon-absorbing power would be 100-50X0.15-7X3+20X0.50=81.50; that is, 81.50 per cent. of the carbon-absorbing power of pure iron.

Jan 12, 1913

By George R. Mitchell

It is a common observation that objects having, different; temperatures exchange energy by radiative transfer. The quantity of radiant energy emitted by an object is a definite function of its temperature. Therefore, a measurement of emitted radiation, by means of a calibrated radiometric instrument, provides a temperature measurement without contacting the emitting object. The physical laws describing radiant energy transfer and their application to remote temperature measurement form the substance of this paper. The energy radiated by bodies having temperatures up to 4000°C is largely in the infrared spectral region. The infrared spectral region is that part of the electro-magnetic spectrum having wavelengths longer than visible light and extending to the microwave region. The wave-lengths range from 0.7 micron (1 micron = 10-4 cm) to 1000 microns. In general, infrared radiometry deals, with the methods of measuring energy flux in the 1 to 15 micron region of the infrared spectrum.

Jan 1, 1960

By Frans van Grunsven, Cees van Rhee, Geert Keetels

One of the obstacles during the initial phases of project development is the assessment of the environmental impact. Mining residue, consisting of fine seafloor sediments, are to be discharged subsea to mitigate the impact of these suspended particles. In order to test the effectiveness of discharging in proximity of the seabed, a numerical model is developed within the open source software package OpenFoam. Dedicated laboratory experiments for numerical model validation are discussed within this paper. INTRODUCTION Siltation is considered one of the major pressures on the environment for a seabed mining operation. Siltation is defined as the pollution of water by a high concentration of suspended sediments like clay or silt. This can be caused by two main activities during the mining process: the spill loss during the excavation and the return flow of undesired seafloor sediment after ore filtration on the ship. In a concentrated cloud, these fine particles form a so-called turbidity plume. Prediction of the size of these plumes and the created layer thickness of deposited sediment is a crucial part of the environmental impact assessment. The challenge in predicting the behaviour of these plumes is found in the wide range of scales involved in the process. At the point of origin, the turbidity plumes spread mainly under the influence of turbulent whirls created by an initial momentum and a buoyancy difference due to the presence of the suspended sediment particles. If carried by ambientcurrents, these plumes can spread for several kilometres before blending in the background.

Jan 1, 2018

By Erwin Stötzer, Renato Fiorotto, Wolfgang G. Brunner, Manfred Schöpf

"Deep mixing methods can be used economically for the construction of cut-off or excavation support walls where other systems such as traditional soldier beams and lagging walls would yie ld unsatisfactory performance, where the installation of vibrated or driven sheet piles could cause vibration induced settlements and where concrete diaphragm walls would be time consuming and expensive. The new CSM method can largely replace the more conventional single or multiple auger methods of soil mixing or jet grouting. The cutter tool is similar to a cutter used in diaphragm walls or cut-off walls and is operated with a Kelly mounted on a drill rig. With this system much deeper walls can be installed and even hard soil layers can be penetrated. CONVENTIONAL SOIL MIXINGIn 1962 Norman Liver patented an auger-based soil mixing technique that has become the basis for the world's current technology.The deep mixing method (DMM), as it is known today, is an in situ soil treatment and improvement technology where the soil is blended with binders and/or other materials that are introduced in a slurry or dry form.Typically one or more hollow, rotating mixing shafts tipped with some type of cutting tool are mounted vertically to the mast of a base carrier and are driven into the ground by hydraulic or electrically powered rotary heads. The shafts above the cutting tool may be further equipped with discontinuous auger flights and/or mixing paddles. The binder is injected through the hollow shafts to nozzles located near the cutting tool where it is mixed with the ground to form columns of treated soil.Individual column diameters range from 0,6m to 1,5m and may extend to 40 m in depth. They can be arranged individually or in contiguous or secant patterns to produce a wide range of treated soil structures on both land and marine projects. Typical configurations are: Single elements, rows of overlapping (secant) elements, grids, lattices and blocks (Fig. 1 )."

Jan 1, 2005

By Peter T. Chiang

A brief literature review on metal separations by ion exchange and solvent extraction of their thiocyanate complexes which are practiced in analytical chemistry as well as in industries was performed. Owing to the poor stability of free thiocyanic acid in acidic aqueous and organic media, technical and environmental problems which cause high thiocyanate consumptions often arise during the practice of the separation processes. This prompted the conducting of a second and more thorough literature review on the chemistry of thiocyanic acid. The objectives of this undertaking are to compile and interpret literature data on the physical properties and chemical reactions of thiocyanic acid, thus providing a clearer understanding of the causes of these problems and giving options as to how to minimize them. The best answer found for carrying out the separation processes is to keep the temperature, thiocyanic acid concentration and total acidity as low as practical.

Jan 1, 1984

By G. M. Behrend

"AbstractMeasurement and control systems in minerals processing plants are usually well thought out and designed. The criteria and design parameters have been interpreted correctly.However, these systems often fail to perform satisfactorily or break down altogether as a result of in-plant conditions which are unpredictable and over which the instrument systems designer has no direct control. The foresight necessary to anticipate the problems and allow for them in the systems design can only be generated by experience.This paper lists the most common of these problems and offers practical methods for their solution. It then follows with an analysis of instrument installation practices and comments on special points that need watching.Finally, instrument maintenance is discussed with a view to achieving good maintenance at the best possible economy.Good MeasurementGeneralTHE MINES and mineral processing plants of the nineteen seventies, after decades of sensible caution, have now committed themselves to extensive automatic control. X-ray analyzers are freely specified. Sample acquisition systems are efficient and automated, computers are reliable and relatively cheap, and computer control systems in conjunction with the new analyzers are operating in a good many plants and are proving to be profitable.The sight of shift foremen and floor operators assembled in front of a TV-tube and taking a computer data display as gospel truth is quite common now, and yet was quite unthinkable only ten years ago."

Jan 1, 1977

While this paper is directed towards the ?Bellambie? type of rope attachment, the principles can be applied to any brand of rope fitting however, it is a only a broad outline and the specific installation and maintenance procedures can be obtained from the attachment supplier. The types of attachment to be discussed are:- ?Thimble Type rope cappel ?Wedge Type cappel ?WRC Rope Clamp ? (Rope Glands) ??Hoist and Balance Rope Sockets In each case, the assembly and stripping (disassembly) plus the basic maintenance procedures is briefly described. A guide for Risk Assessment is also included but because of his familiarity with the installation, the end-user is in the best position to draft the final version.

May 1, 2003

By R. W. Raymond

It is impracticable to prepare for the present number of the Bi-Monthly Bulletin a detailed account of the memorable Joint Meeting of the Iron and Steel Institute and our Institute, held in London, the last week in July, and of the, innumerable festivities, entertainments and excursions which accompanied and followed it, in England, Scotland, Wales and Germany. This preliminary sketch, from which all " useful particulars "' have been carefully omitted, is published unofficially, as a convenient answer to the manifold inquiries of members who did not go, and who are now trying to alleviate their unavailing regret by indulging their curiosity. Perhaps they secretly hope to hear that they did not lose so very much, after all-that the affair was not all that could have been desired or dreamed; that there were serious drawbacks, shortcomings and disappointments; and that it is just as well to have stayed it home, and now to hear about it. Let them lay no such flattering unction to their souls. The month they have missed would have been the time of their lives. They will never, never know how good a time it was, or adequately repent of their folly, if they could have gone with us, and voluntarily did not go of course, those who would but could not, have our immeasurable pity, without blame. I shall present here no consecutive and minute story, but only a series of general paragraphs concerning different aspects and stages of our experience. THE WEATHER. The proverbial good fortune of the Institute attended its visiting members and guests at every stage of the late London meeting and the numerous excursions which accompanied or followed it. Even the process of crossing the Atlantic was made delightful by smooth seas, through which the great modern transatlantic liners made their way without disagreeable

Sep 1, 1906

By Fred V. Seibert

The Functions and the Responsibilities of the Institute The Canadian Institute of Mining and Metallurgy is unique. ln addition to the welfare of its members, it has a real interest in the welfare and promotion of one of Canada's largest and most important basic industries. It is because of this that the membership is composed of both individual and corporate members. The individual members are both technical and non-technical (Members and Associates). Both Members and Associates have the same status in the Institute and all are interested in the welfare of the mineral industry. The aims and objects of the Institute 11re twofold. The education and welfare of its individual members and the sound promotion and welfare of the mineral industry. Perhaps it might be well if we reviewed these aims and objects as stated in our Constitution: "First - To promote the arts and sciences connected with the economical production of valuable minerals and metals, by means of meetings for the reading and discu11ion of technical papers, and the subsequent distribution of such information as may be gained throo.gh the medium of publications". It cannot be denied that we have do ne a good job in this particular phase of our work. Nevertheless, there is still room for improvement. It has been suggested that we might have more discussion and, on occasions, more criticism of our papers and programmes. This can best be done if the authors will have their papers prepared in sufficient time to permit of preprints being made availa1ble before the meeting at which they are to be presented.

Jan 1, 1950

By Daniel C. Jackling

WHAT is written here features some of the things that I would say if I were to de- liver a Presidential address during the Annual Meeting to be held this month in New York. I am aware that custom favors written rather than vocal delivery of such a discourse; and, as this accords exactly with my own preference, I assure readers that they will never be called upon to hear these remarks spoken- anyhow, not by me. My year as President is drawing to a close. As I look back I like to classify and analyze the impressions that have been left with me. It has been a delightful and fascinating experience to me personally; I have appreciated the courtesies and aids, and have been deeply gratified at the honors accorded me. Perhaps the source of greatest satisfaction is the opportunity I have had to sense more about the provinces of this Institute and about the useful functions of the profession that it represents. For 38 years I have been a member. I served two terms as Director-one in 1914-'16 and again in 1927-'29. I have been honored by selection as a Saunders Medalist. I thought I was reasonably familiar with the functions, the ideals, and the activities of the Institute. But the things that I have discerned during the past year have dispelled that conceit. I still think that, a year ago, I was as well informed as most members; but since then I have had the rare privilege of executive service and insight. That has given me a perspective that I feel can be obtained in no other way-as I think the illustrious engineers who have preceded me in office will agree. I wish that I had the power to translate to every member somewhat of the feelings of pride in our organization that a year as President cannot help but instill.

Jan 1, 1939

New York, March 18, 1913. MR. CHARLES F. RA ND, President, New YORK, MARCH American Institute of Mining Engineers. Dear Sir: In connection with the official notice of Dr. Raymond's unanimous election by the Directors as Secretary Emeritus, we wish to place upon record certain statements concerning his services to the Institute which we think have not been published., and may not be generally known to the majority of our fellow-members. When the Institute was formed in 1871, Dr. Raymond acted as Secretary of the Founders' Meeting, and became the first Vice-President of the Institute, and, by request of the aged and beloved David Thomas, who was the first President of the Institute, Dr. Raymond discharged all the duties of the office of President, to which he was later formally elected in 1872, and which lip held for three years. During that time, he visited Europe, and through his acquaintance and reputation abroad, established those international relations of the Institute which proved so important in later years. He also enlisted the support of the mining engineers and metallurgists of the Pacific Slope, who would not otherwise have been disposed to join a society originating in the East. And for twelve years he attended; at his own expense, nearly every meeting of the Institute, wherever held, giving to it without remuneration his best service, and sacrificing for it many professional and private interests.

Jan 4, 1913

By AIME AIME

THE official opening at the 134th general meeting of the Institute was held on Oct. 6, but it was prefaced by two round table conferences on Oct. 5. The open-hearth group held the fourth of their semi-annual conferences at the William Penn Hotel, devoting the morning session to discussing a paper by R. L. Cain on the "Manufacture of Forging Steel by the Open-hearth Process," and the afternoon to discussing P. H. Shaeffer's paper on the open-hearth charge. At the Bureau of Mines, a round table conference on the combustibility of coke was held on Tuesday morning, and the afternoon was devoted to a similar conference on the testing of coke. The formal opening session of the meeting assembled in the Music Hall of Carnegie Institute at 10.30 a. m. Graham Bright, chairman of the Pittsburgh Section; called the meeting to order and presided. President Taylor welcomed the visiting members and guests to his home city and reviewed briefly the advancement of mining in the past half century during which, for ex- ample, the coal output had increased from 53,280,000 tons to 523,357,000 tons per year. He emphasized the important part Pennsylvania played in mining and brought out the principal changes that had taken place in methods. In part, his remarks were as follows: The centennial year, 1876, found the coal business of. this country, as a whole, producing 53,280,000 tons, of which amount the bituminous mines of this State yielded 24 per cent. In 1925, this country produced 523,357,000 tons of coal, of which Pennsylvania produced 24 per cent.

Jan 1, 1926