Search Documents

By WILLIAM BOWIE

THE development of the isostatic idea during the last century would make an interesting paper in itself. But the various steps in the development have been covered in a number of papers and books which are readily available. Therefore this short paper should not give space to. the historical phases of the subject. Isostasy is really an old idea, but it is only in the last few decades that it has taken on any great prominence or importance in the study of earth phenomena. It is really remarkable how closely Dutton' sensed the isostatic principle 40 years or more ago. His general principles of isostasy as outlined by him have stood the test of time and fit in closely with the general ideas held today. It would seem, however, that some of his views with regard to the application of isostasy to geological processes must be modified or abandoned.

Jan 1, 1930

By J. C. Irvine

A recent development in underground drilling has been the introduction of the down-the-hole drill, an old and very familiar tool to the surface operator. The idea of moving such a rig underground is not new. Tests were conducted at INCO in Canada and Mt. Isa, Australia in the early 1960's, and St. Joe used one for underground exploration in their Missouri lead mines in the mid-1960's. However, the trend to full scale production programs did not start until the mid-1970's. The first successful North American test was at INGO in early 1973. This led to a large-scale pillar recovery and open stoping program which en¬compassed 25 drilling units by mid-1976. Meramec Mining Company tested a unit using air boosted up to 200 psi (140, 000 kg(m2) in the summer of 1973 which by 1976 led to an open stope and pillar drilling program using 12 units. By mid-1976, production units using boosted air were also in use at Pilot Knob in Missouri and at St. Joe in Balmat, New York. Experimental and utility units were in use in several other mines and down-the-hole drills were being seriously considered for at least one major new underground mine.

Jan 1, 1976

By D Kent

The introduction of digital technologies into the underground mining industry, in both coal and hard rock mining, has enabled many high bandwidth applications to be adopted by mines.Digital networks based on 802.11 b/g/n open Wi-Fi standards allow for many applications to be run over a single communication backbone. One important application has been tracking personnel and equipment via RFID tags. This tracking application has in turn formed the basis of a Proximity Detection System (PDS) or Collision Avoidance Systems (CAS). The paper discusses the growth in digital technology as the communication backbone in underground mines which has allowed the ‘convergence of technologies’ that has been occurring in the general business world to be available to underground mine operators. Then the paper will focus on the use of the technology in the increasingly important are of risk control around mobile plant underground. The specific use of digital devices for proximity detection, in both hard rock and coal mines, to provide a system that can deliver an additional level of control to the risks associated with people-vehicle interactions underground is discussed. The initial implementation of PDS in the hard rock mining environment is based on two zones of detection, required for large and relatively high speed vehicles. Information will include:•the principles of the underlying technology,•installation learnings and effectiveness, and•change management methodology and issues.The most recent development to integrate Mine Site Technologies (MST) PDS with Frederick Mining Controls’ HazardAvert® System to extend the overall Proximity System’s functionality in hard rock mines and for use in coal mines is overviewed.

Mar 21, 2011

By M. A. Trevits

During the time period from 1990-2007, 1601 reportable fires occurred in the U.S. mining industry (an average of 89 fires per year). The leading causes of U.S. mine fires were flame cutting and welding operations, frictional heating and ignitions, electrical shorts, mobile equipment malfunctions, and spontaneous combustion. The fact that mine fires continue to occur with an alarming regularity reinforces the importance of recognizing and eliminating the potential hazards and the overall need for improved fire control and suppression technology to ensure the best possible outcome during a mine fire. The National Institute for Occupational Safety and Health (NIOSH) is conducting an evolving comprehensive program of research that is addressing mine fire prevention, detection, management and suppression. This paper presents a summary of recent research accomplishments and provides an overview of the next phase of the NIOSH mine fire research program.

Jan 1, 2008

This paper presents an overview of the current status of mine water management in South Africa. The regulatory framework within which mine water management operates is set out, based on the principles and policies embodied in the relevant legislation. The status of the gold and coal mining industries, with regard to water management, is presented on the basis of studies that have been undertaken to develop water and salt balances for these industries. While the data is not available to quantify the status of ARD in South Africa, the range of typical mine water quality problems faced by South African gold and coal mines is presented. The status quo, problems and challenges relating to mine water management are presented and discussed. It is shown that, while there have been major strides in the last decade, and mine water management and treatment in South Africa has moved onto the forefront of mine environmental management, important problems still persist. There is still a significant amount of improvement required, particularly in the field of prediction of water quality deterioration and the application of such predictions to the identification of management actions that can be applied to prevent or minimise mine water pollution in the shortmedium- and long-term.

Jan 1, 2003

In October 2005 Phelps Dodge mining, a US based company, visited several Australian mining companies and mine sites to ascertain the current applications of risk management methods in the organisation. The results of this review, documented by the author, indicated a ælayeredÆ approach from high level site or major hazard analysis through to face level, æstop and lookÆ, methods. The approaches of several companies were summarised in one simple layered model. This model is helpful to other sites and companies to identify potential improvements but also offers an image of best practice that may assist with the governance of OH&S by both company boards and community regulators. The issue is particularly relevant as we discuss national consistency in mining regulation. This paper examines the layered model, the company and site approaches that helped define the model, as well as the suggested implications of the layered model to governance.

Jan 1, 2006

By Bauer, Alan

In considering blasting it is necessary to consider the drilling and explosives since one is generally concerned with the total cost of muck of a certain size in the pit or through the crusher. To get a current idea of the drilling situation in open pit mines plotted in Fig. 1 are the drilling costs per ton of material vs. hole diameter for rotary drill holes in large limestone, iron ore and taconite operations. The exception is the 2-in. diam hole which was drilled with a percussion drill in limestone.

Jan 1, 1968

The primary steel industry of the Prairie Provinces consists essentially of three companies whose total annual melting capacity, as of January 1, 1963, was 333,000 net tons. These companies have steel rolling facilities. In addition, there are five other companies producing steel castings by melting scrap in electric furnaces which, with the plants having rolling facilities, gives a total annual furnace melting capacity of 380,000 tons. Since 1954, the annual production of steel ingots and castings has ranged from a low of 66,588 tons, in 1954, to a high of 211,138 tons in 1961. The present facilities on the Prairies for making steel ingots from scrap, and rolling them to produce light merchant mill products, appear to be sufficient for many years ahead. Steel scrap, as electric furnace feed to make steel ingots for the present line of products, will probably continue to be available at reasonable prices either on the Prairies or from the north-central United States. It is recognized, however, that residual elements in scrap may be-come of greater significance and necessitate more rigid control of scrap quality.

Jan 1, 1963

The object of this paper is to give an insight into various metallurgical operations involved in the making and shaping of steel for shipbuilding at the Newcastle plants of the Broken Hill Proprietary Co. Ltd., Commonwealth Steel Co. Ltd. and the Port Kembla plant of Australian Iron and Steel Ltd. Whilst not steelmakers, inasmuch as their processes start with semi-finished. steel supplied by the Steelmaker, the plants of Stewarts and Lloyds (Aust.) Pty. Ltd. and their associate company, British Tube Mills, Rylands Bros. (Aust.) Pty. Ltd. and the Newcastle and Kembla plants of John Lysaghts (Aust.) Pty. Ltd. make substantial contributions to the Australian shipbuilding industry, principally by way of boiler tubing and wires for welding rods and sheet steel, including special silicon lamination sheet for electrical motors.THE MAKING OF STEELThe making of iron and steel began as an accident, slowly developed as an art and has not yet become an exact science. The iron age dawned on the day when, by chance, man's primitive ancestor built up the wall of his fire with ironstone. In the ashes of the fire he found pieces of sponge iron from which he hammered out the first sample' of wrought iron. For many centuries iron ·was manufactured in bloomeries and occasionally, when the temperature was excessive, the iron combined with some carbon and steel was produced. But it was not till '1740 that steel was manufactured under controlled conditions. In that year Huntsman invented the crucible process which held undisputed sway for over a 100 years until in 1856 the invention of the Bessemer process revolutionised the whole industry.From then on, rapid progress was made. The Siemens...

Jan 1, 1951

By FRABK HERVEY PETTINGELL

THE stock exchange and its functions is about as well understood by the average individual as the fourth dimension. What is a stock exchange? Divested of the rules and regulations by which it is governed, and the facilities it provides for the convenient handling of securities, it would be in its nude state nothing more or less than a meeting place for brokers. The stock exchange in America dates back to 1752, when a group of merchants of New York established a meeting place at the foot of Broad Street for the purpose of dealing in meal and slaves. The first definite orgarization, however, had its beginning in 1792 when 24 New York brokers signed an agreement not to buy or sell public stock for less than one quarter per cent. commission. From this small group has grown by gradual degrees, the greatest organized security market in the world, namely, the New York Stock Exchange. At the present time there are 27 stock exchanges in the United States and 5 in Canada. Based on the volume of business transacted, the Los Angeles Stock Exchange ranks 6th among them. This is attributable to the fact that strictly speaking Los Angeles has never been a stock exchange town, like some other large cities. Take for instance San Francisco, which supported one stock exchange from 1862 to .1882 and has since supported two. No city, by the way, should tolerate two stock exchanges at the same time. It is an economic folly and a senseless duplication that can be compared with rival telephone companies or competing street railway systems, paralleling each other's lines and always leads to trouble and confusion, and sooner or later one or the other falls by the wayside. While Los Angeles has had stock exchanges of one kind or another since 1896, none of them attracted much attention until 1899 when the present exchange was organized and it did not get well under way until along in 1906.

Jan 1, 1925

By Harry J. Evans

DURING the fury of the conflict it was believed quite generally that World War II was being fought for and would accomplish a permanent peace. Yet, before the guns were actually stilled on all fronts, the American people realized that the devastated world would continue to be dominated by suspicion and uncertainty. The misunderstandings which rapidly developed indicated that it may prove unwise to rely wholly on mutual international agreements and contracts to avoid war. Before the celebrations of V-Day died down serious thought was being given toward measures for preparedness for the next conflict. Along with a realization of the enormous loss of life caused by the destructive forces of war, the American people came to understand the seriousness of the rapid and unwarranted depletion of our natural resources. During the last half of 1945 the question of stock-piling strategic and critical raw materials for a future national emergency became an intensely live subject.

Jan 1, 1946

By R. V. Norris

1. INTRODUCTION. THE anthracite coal trade, with a shipment averaging about 70,000,000 tons per year, differs essentially from other coal business, in the fact that the larger sizes, comprising about 65 per cent. of the total, are used almost exclusively for domestic purposes, principally during the winter months; and that for proper combustion close-sizing is imperative, so that eight sizes are made; broken, egg, stove, and nut, known as prepared sizes, and pea, buckwheat, rice, and barley, known as steam sizes. These sizes are made in the regular course of preparation, and but little variation in the natural percentage of each is practicable. Thus it is necessary either to work the collieries intermittently, or to dispose of all the varying sizes in their fixed proportions. Unfortunately, the market does not at all times absorb the coal in proper proportions, and rather than interfere with the regular operation of the mines it has been found economical to provide storage for the excess. While the cellars of the consumers are the great storage-plants of the country, this capacity is not under the control of the trade, except so far as reduced prices during the spring and summer months may tempt the use of this reserve. The same remark applies but with less force to the retail yards, which,, though usually small, store in the aggregate a large amount of anthracite. While every effort is made to utilize to the utmost the individual storage-capacity of the country, there still remains the necessity for taking care of the irregularities of the market by the construction of storage-plants under the direct control of the producers. Such plants are usually the property of the railroads, and are situated at points most convenient from a traffic stand-point.

Jun 1, 1911

By L. H. Cole

Introduction The increasing importance of the gypsum industry in Canada is evidenced by the fact that the production has increased from 473,129 tons valued at $809,632 in 1909 to 1,205,846 tons valued at $3,622,007 in 1928, an increase of over 155 percent in quantity, and of 347 percent in value, in the 20-year period. Although the export trade in crude gypsum still forms a large proportion of the industry, it is gratifying to see that the home consumption is steadily increasing, and while the percentage of the crude gypsum mined that is manufactured into the calcined products in the country is only 16.8 per cent, its value is practically 50 per cent of the total gypsum production of the whole country. It is to be hoped that each succeeding year will see an increase in the amount manufactured in Canada, and, with the steady growth of the country and a serious endeavour to capture a part at least of the world market in gypsum products, the outlook for the industry is decidedly promising. The value of gypsum as a commercial commodity has been known from the time of the early Egyptians; in fact its value for certain purposes has been known so long chat the date of the discovery of its peculiar properties is unrecorded.

Jan 1, 1930

By Zoë Mullard

The introduction of Web 2.0 platforms (also referred to as social media), with their architectures of participation, has ushered in a new era of technological interaction and information exchange that is changing the nature of corporate-community communications. Web 2.0 platforms give users the ability to generate data collaboratively, meaning that more stakeholders maintain the expectation of being able to contribute to online dialogue. In light of these changes, it is important for business to consider how social media can be used strategically to enhance stakeholder relationships and increase business efficiencies. This article provides three case studies of how different stakeholders in the mining industry are strategically using Web 2.0 platforms to communicate with target audiences. The case studies are based on the experience of respondents and from website observations, which were undertaken as part of a thesis research project by the first author (Mullard, 2010), focusing on the application of social media in the mining industry.

Jan 1, 2011

By V. Montaruli, A. Nieto, M. Cardu

Nickel is a metal whose workability and mechanical strength at high temperatures and in corrosive environments makes it an indispensable alloying element for the realization of stainless steel, specialty steel, super-alloys, rechargeable batteries and electroplating. Because its main fields of application are key to the development of industry and, thus, to society, nickel has recently been recognized as a potentially critical mineral, despite its abundant reserves. The purpose of this paper is the creation of possible case scenarios determined by factors and events that, in the medium to long term, could change the current structure of the nickel market on the demand and/or the supply side. Four scenarios have been determined by considering a demand variation due to the occurrence of a natural disaster and an aerospace plan implementation and taking into account the resource nationalism and the skills shortage as supply varying factors. Through the creation of a georeferenced global nickel database, the paper proposes supply strategies related to the four scenarios for each top nickel consumer: China, India, European Union, United States and Japan.

Jan 1, 2013

By R. C. A. Thurston

Introduction A mechanical spring has been .defined by Wahl ( 1) as 'an elastic body whose ?primary function is? to deflect or distort under load, and which recovers its original shape when released after being distorted'. Most material bodies are elastic to some extent ? and will deform under load, but they are seldom regarded as springs since this is not their primary function. The principal applications of springs are the absorption of energy and the mitigation of shock, the support cf moving masses or the isolation of vibration, and the provision or measurement of definite loads or torques. A large number of spring types have been developed to serve these purposes and to meet the different operational requirements; they range from the large semi-elliptic leaf suspension spring to the delicate watch hairspring. The springs of most importance in machine design, however, are the helical round-wire compression or tension types. They are made in a wide variety of sizes and are used in tremendous quantities, mainly because of their low cost, their compactness, and their relatively high efficiency. Their field of application is as broad as that of machine design itself, but the bulk of production is almost certainly for suspension systems of vehicles such as automobiles, freight and passenger cars, and mine cars, and it is with the last of these applications that this paper is primarily concerned.

Jan 1, 1951

By A. L. Ph. B. Holley

(Read at the Philadelphia Meeting, February, 1878.) THIS paper is an abstract and a discussion of results obtained by the United States Test Board in experiments upon 14 brands of wrought iron, most of which are well known and of high repute.* The iron was all intended for chain-cables; it was tested in the form of bars, usually of nine sizes, from 1 inch to 2 inches round, and also in the forms of single links and short chains. Not less-than 2000 tensile tests were made, each showing elastic limit, elongation, and reduction of area. This work was done with conspicuous intelligence and fidelity, at the Washington Navy Yard, by Commander L. A. Beardslee. Some important practical results and principles which he has developed, and others which he has confirmed, will be referred to. The chemical part of this work consists of 42 complete analyses (including slag), by Mr. Blair, chemist to the Board. EFFECTS OF COMPOSITION ON STRENGTH. Variations in the physical qualities of iron may he due to different composition, or to different treatment in manufacture, or to both these complex causes. In order to determine the specific causes of variation, one class of altering conditions should be made to vary largely, while the other classes should be kept uniform. Then another class should be varied, and so on, until the value of each is ascertained. As all the irons under consideration were intended to have that purity and refinement which was deemed indispensable in chain-cables, their chemical analyses are perhaps more important in proving that physical variations result chiefly from treatment, than in pointing out the specific effects of certain ingredients. While the subject of treatment-especially the increase of strength by greater reduction in rolling-may be the more important one, it can be best appreciated after we have familiarized ourselves with the gen¬eral chemical and physical characters of the irons. The typical facts are given in the following tables. * As the present object of the Board is not to compare the products of different makers, but to discover the physical effects of various composition and treatment, the irons are designated by letters rather than by their trade names.

Jan 1, 1878

By Real Daigneault, François Robert, J. Paul Golightly, Jean-Yves Cloutier, Jayanta Guha, Pierre Pilote

"The Casa-Berardi East, Center and West deposits, located in the Archean Abitibi, Sub province, are hosted by volcanic and sedimentary units of varying compositions, less than300 m from the Casa-Berardi fault (CBF). The CBF, a brittle structure, represents an increment in the structural evolution of a regional-scale deformation zone showing ductile-brittle behavior known as the Casa-Berardi deformation zone (CBDZ). The CBDZ is characterized by a mylonitic Sc1 foliation which is folded a.n4 deformed by a later sczfoliation in high strain zones.Four generations of quartz vein and fracture systems have been recognized within the Casa-Berardi deposits. Most economic gold mineralization, occurring in the second generation system, is found within high strain zones. This system hosts three types of mineralized structures: (1) banded quartz veins; (2) swarms of veins and mineralized host rocks; and (3) disseminated sulphides along fractures. An early carbonate hydrothermal alteration zone (pre- to syntectonic) surrounds the deposits. Alteration associated with gold mineralization is contemporaneous to late ( syn- to post-tectonic) relative to the development of progressive deformation in the CBDZ. The geological characteristics and paragenesis of the four quartz vein and fracture systems developed as an integral part of the geodynamic evolution of the Casa-Berardi deformation zone."

Jan 1, 1990

By W J. Botha

The Palaeoproterozoic Transvaal Supergroup in the northern Cape Province of South Africa hosts high grade (>60 per cent Fe) hematitic and specularitic iron and manganese mineralisation. The mineralisation is primarily exposed along the western margin or in the central part of a major interference fold structure known as the Maremane dome. The bulk of South AfricaÆs iron ore production is currently provided by two active mines, Kumba Resources megaton Sishen iron ore mine on the northern end of the dome, and the smaller Assmang Beeshoek mine on the southern closure. The undeveloped Sishen South deposit, which contains ~400 Mt of high-grade hematite ore, is located approximately 9 km towards the southwest of Postmasburg. It forms a linear extension of the Beeshoek mine and as such contains comparable laminated, breccia and conglomeratic iron mineralisation. The Transvaal Supergroup sediments were deposited in two distinct fault-controlled basins on the Archean Kaapvaal craton. Basement rocks in the western Griqualand West basin are formed by a carbonate platform sequence (Campbellrand Subgroup), which is overlain by a thick sequence of banded iron formation of the Asbesheuwels Subgroup. A major unconformity separates these rocks from the red-bed Gamagara Formation, which is correlated with the base of the Olifantshoek Supergroup. Diamictites and lavas of the Postmasburg Group have been thrust over these units from the west. The mineralisation process is related to regional scale supergene iron enrichment of Kuruman banded iron formations along the unconformity. During regional tectonism associated with the Kheis orogeny (2400 - 1700 Ma) the Maremane dome was uplifted, and the basal dolomite units thus exposed to erosion and karstification. The overlying banded iron formations collapsed into karst sinkhole structures where leaching of silica and enrichment of hematite occurred. Although the exact mechanism of the mineralising process remains unclear, karstification preserved components of the original concordant laminated and massive ores. These ores were subsequently eroded and deposited as conglomeratic and gritty ores down-dip of the Maremane dome in alluvial fan systems. A thin veneer of recent calcrete or Tertiary Kalahari clay beds masks the subsurface geology and most of the orebodies, thus ground geophysical gravity surveys proved excellent exploration tools to penetrate the surficial cover. These surveys were used extensively for delineation drilling and to deduce the subsurface geology and structural development of the area. Finally Sishen South orebodies were modelled with ModelVision software in an attempt to obtain an exploration template for the surrounding area.

Jan 1, 2005

By S. E. Sankey

High anionic functionality acrylamide co-polymers and poly(sodium acrylate) are used as red mud flocculants in bauxite processing operations. These synthetic polymers are effectively displacing starch as the dominant polymer in red mud settling. The performance of these polymers is primarily dependent on the bauxite mineralogy, the alkalinity of the red mud slurry, and the anionic functionality and molecular size (viscosity) of the polymer. In this paper, the physical and chemical properties of the synthetic watersoluble polymers will be reviewed. The relationship between polymer structure and red mud slurry properties as they control polymer performance in settling red muds common to digester and washer circuits will be illustrated. The availability of polymers of varying functionality and viscosity will permit bauxite processors to make significant improvements in the economics of red mud disposal and valuable reagent recovery.

Jan 1, 1982