Search Documents

By R. H. Sergent

The interest in using halogens for extracting precious metals from ores has increased due to changes In ore characteristics, environmental concerns and regulations. The rediscovery of halogen leaching capability has been the topic of these and other writers1-30. Much work has been done on the performance of bromine, chlorine and iodine5-29. Of these, bromine and chlorine look most promising. Iodine is quite expensive and sometimes forms an Insoluble film on a precious metal surface22,23. Little experimental work has been published on the relative performance of bromine versus chlorine. The Pourbaix diagrams for the halide leach system (see Fig. 1-4) Indicates a significant stability advantage for bromine In forming complex ions with gold. This should result In greater extraction of gold under similar leach conditions and Is evaluated In this work. The regeneration of halogen from a spent leech solution is a critical requirement for an environmentally acceptable halogen leach process. Bromide can be oxidized In-situ to bromine ~ adding chlorine or ozone2,31. Bromide like chloride can be oxidized In an electrochemical cell to produce halogen on demand 13,15,17. Bromine clearly offers a number of possible regeneration pathways. This work strives to compare the relative ability of chlorine and bromine to extract gold from partially and fully oxidized ores. A commercially pressure oxidized sample was evaluated under a number of experimental conditions. The autoclave feed ore from the same mill was also evaluated after complete oxidation In a laboratory autoclave.

Jan 1, 1993

By John F. Oyler

The performance of high alumina refractory subjected to high compressive loads and high temperatures is an area in which operating experience is quite limited. This paper documents the results of five months of operation of a combustion chamber lined with 83 pct alumina brick subjected to compressive stresses as high as 45psi and hot face temperatures of about 2750°F. It also describes a method for predicting long term subsidence results based on the limited information available in standard hot load limit tests. Descriptions of the chamber itself and the pilot plant upon which its design was based are included.

Jan 1, 1978

By P. N. Calder, D. B. Apel, S. D. Butt

Mine-wide (MW) microseismic systems use widely spaced transducers to determine the source location and parameters of stronger microseismic events, while high frequency (HF) systems use fewer transducers to monitor local areas for the weaker events that can precede stronger events. Previous monitoring at the Creighton Mine indicated that an HF transducer located 120 m away from an active stope recorded two types of activity in response to production blasting: the first occurring at the same time as the production blasts and associated with the passage of the direct seismic waves from the blast through the local area, and the second occurring several hours later and associated with the arrival of a slower moving stress change through the rock mass (which was identified by the mine’s MW system). Interpretations of locally increased stress levels, based on analysis of the recorded HF events, correlated with the nearby occurrence of two strong seismic events. These results were applied to a similar monitoring trail at the Kidd Creek Mine where the transient stress changes induced by several development blasts were monitored. It was observed that increases in HF activity corresponded with the occurrence of MW events near the transducer location, and that fewer HF events were recorded the longer this occurred after the blast. Local geological features appeared to influence the number and occurrence of both HF and MW events.

Jan 1, 2000

By R. H. SWEETSERS

A Discussion of Mr. Hall's paper, read at the Washington Meeting, February, 1905. R. H. SWEETSER, Sault Ste. Marie, Ont. (communication to the Secretary*) :-The recent work of furnace No. 1 of The Algoma Steel Co., at Sault Ste. Marie, Ontario, using for fuel, first all charcoal, then a mixture of charcoal and coke, and finally all coke, upsets the estimates given by Mr. Hall in the last two paragraphs of his interesting paper. Furnace No. 1 was built for a charcoal-furnace, and it was run on charcoal fuel from March 6 until July 9, 1905; then, for a week, a mix¬ture of charcoal and coke was used, and, since then, coke alone has been the only fuel. It is to be regretted that at no time, during the run on charcoal, was there enough charcoal on hand and " in sight'" to warrant blowing the furnace as hard as it should have been blown. During April and May the supply of charcoal limited the amount of blast to about 8,000 cu. ft. of air per min.; in June, to about 8,900 cubic feet. For a few days in July about 10,000 cu. ft. were blown, and then the maximum daily output, 173 tons (2,240 1b.), was reached. At all times the quality of the charcoal was poor, having been made from wood cut from three to four years before. Doubtless this furnace could have produced .200 tons of iron per day, even with this quality of charcoal, provided the supply had been sufficient; and with good charcoal I see no reason why it could not make as much iron per day as it has made with coke. During the one week of using a mixture of charcoal and coke, the changes in quantity of blast and composition of the slag followed each other so closely that no single condition could last long on the furnace. The results were good, and the pig-iron was about the same in quality as that made during the

Jan 1, 1906

The paper describes data from test work programs on a range of magnetite ores in Australia and overseas. The analysis looks at the behaviour of material of different sizes fed to the rolls and the change in product size as a result of that, the conclusion being that there is a logarithmic relationship. The paper develops a form of equation to predict the product size from a given feed size distribution. The behaviour of the various magnetite ores is compared to more standard test methods such as crushing work index and unconfined compressive strength.

Jan 1, 2009

By G Hall

BHP BillitonÆs (BHPB) Yandi ore deposit is a channel iron deposit (CID) in the Pilbara district of WA. The ore is predominantly a goethite-hematite pisolite and overlays a clay at the base of the deposit. Knowledge of the location of the contact prior to mining is critical to maximise ore extraction and minimise contamination from and mining of the underlying clays which contain high levels of alumina. The contact between the iron ore and the clay is highly irregular. Traditionally the contact has been delineated by closely spaced drilling û this can be expensive and since each drill hole only provides a point sample measurement, irregularities in the contact surface can be missed. In September 2001, three high resolution geophysical techniques were trialled to see if they could be used to improve the efficiency and accuracy of ore delineation. The three techniques were resistivity imaging, ground penetrating radar and electromagnetic conductivity imaging. The resistivity data showed a favourable correlation with the available ground truth data from drilling. Using this ground truth data as a calibration, an interpretation of the depth to the base of the channel iron deposit (CID) ore was constructed for the areas surveyed. A significant attribute of the method is that the position of the base of the ore is imaged continuously along the lines that are surveyed rather than at discrete points. No continuous well defined ground penetrating radar (GPR) reflections were observed from the base of the CID ore. There did appear to be some correlation between the range of echo times that reflections were observed and the drill data, however the precision to which the range of echo times could be estimated was of the order of several metres and therefore not adequate to replace current procedures. The electromagnetic data showed good correlations with the existence of shallow clays but did not discriminate between variations in CID ore depth. This technique is therefore not suitable for mapping the base of the CID ore but may still be useful as a rapid tool for mapping the position of clay bands.

Jan 1, 2002

It is not often that mines have as much warning of the approach of bad ground conditions as was the case at the Western Mining Corporation, Kambalda Nickel Operations Lafranchi/Schmitz Decline. Most aspects of this operation are in fact quite unique and like the best solutions, the answer to the problem of weak and foliated ground conditions was relatively simple; requiring the use of readily available explosives although the idea of using it in this manner may not be the most obvious.The use of high shock energy POWERGEL 2131 cartridges proved to be the correct answer, in conjunction with small changes in drill pattern design. The resulting lack of overbreak bears testimony to the success of the concept and the commitment of the miners to achieving a safe working environment.

Jan 1, 1992

By H. A. Steane

THIS BRIEF PAPER presents the information available on the use of Dorrclon?is in the middling re-grind unit at the lead-zinc mill of Canadian Exploration Limited. The plant throughput is 1,650 tons per twenty-four hours. The flotation feed is ground to 60 per ?Cent passing through 200 mesh. It contains some composite 11articles of sphalerite in calcite, and these reported either in the final zinc concentrate, thus lowering the grade, or in the tailing, with loss of zinc. The re-grind unit was set up in the zinc flotation circuit to liberate the sphalerite from these middling particles, to raise the grade of concentrate and improve recovery. Grinding through 325 mesh should give substantial liberation of locked sphalerite. The middling regrind unit consists of two Dorrdones and one ballmill arranged as shown in the -accompanying flow-sheet. The Hardinge ball-mill, size 7 ft. x 36 in., was free for this use as a result of recent plant expansion. The two Dorrclones were purchased, and the necessary pumps and pipe lines were installed to complete the regrind unit. The unit has been developed over a period of two years by several steps and various flow schemes until reaching tl1e present flow scheme. These steps are not elaborated here, because the changes were made to determine the best product to work on for flotation metallurgy, and not because of the Domrolone classifying ability.

Jan 1, 1956

By Robert O. Vernon

The discussion of water and pit mining together is most appropriate. In fact, water can be considered a mineral and a well a narrow pit. Thus, of all the mineral resources mined, water is probably the cheapest, most valuable and least valued. The delivered price, including mining, transportation, storage and marketing rarely exceeds ten cents per ton, and our economy would cease without it. The time has come when the public must recognize that the extraction of a mineral resource from the land is a necessary and inevitable result of the industries? attempt to meet the demands of a growing economy. In so much of Florida, the lands mined can, with forethought and planning, be left as improved real estate, water conservation and management lands. On the other hand, the mining industries must face up to the need for the reclamation of land and compact with themselves, appropriate governmental agencies and with the mining states to restore mined lands to usefulness. Of limestone, sand, and clay 90 to 100 percent of the mined material is used, but with planning and specing, these pits, if they penetrate the water table, become valuable as real property. Phosphate, which returns about 70 percent of the mined materials to the pit, can reclaim the land for many purposes.

Jan 1, 1966

By Frank H. Reed, P. W. Henline, Harold W. Jackman

A SUMMARY of the consumption of coal in 1945 shows that the coke industry accounted for 17 pct of the total coal used. No substitute for coke and the blast furnace in the reduction of iron ore has gained sufficient prominence so far to be given serious consideration. However, while the same slot-type ovens are being built and used now as were in use a few years ago, the problem of obtaining suitable coking coals, both high- and low-volatile, has forced many operators to revamp coal-blending facilities. Until the beginning of World War II, high-temperature coke plants were able to secure the required high-volatile and low-volatile coals from two or three seams and from three or four mines. Thus, many of our coke oven plants were able to operate with storage bins for two coals only. The variance in raw materials was not great, and uniformity of blend was a relatively simple problem. Since the beginning of World War II, many and important changes have taken place. Demand for all coals increased greatly. Production, though kept as near maximum capacity as possible, could not meet the demands for coal generally, and particularly for the various kinds of coal which have proved to be satisfactory for specialized uses; coals were allocated as nearly as possible in the order of greatest need; storage piling was reduced to the minimum necessary to keep plants in operation; uniformity of quality could not be maintained, and with this last, uniformity of composition of blends for coking could not be maintained. Whereas before the war producers of metallurgical coke could fill their needs from three or four mines, by the end of the war it was not unusual to find shipments to a single coke oven plant coming from as many as 30 different mines, in a single month. Since many of the mines producing both high- and low-volatile coal for high-grade metallurgical coke are rapidly nearing depletion, the problem of seeking new sources and of blending a number of coals in each plant for the production of high-temperature coke is facing practically every producer in the United States at the present time, and is one which will probably continue for many years to come. Midwestern by-product coke ovens in the Chicago and St. Louis areas use annually from 12 to 15 million tons of bituminous coals which are transported 500 to 700 miles from the Appalachian coal fields of Pennsylvania, West Virginia, and eastern Kentucky. Approximately two-thirds of this coal is high-volatile bituminous. The critical transportation problem confronting the nation in 1943, and the growing scarcity of the best Appalachian coking coals, prompted the Illinois Geological Survey to propose a research program in which would be studied the coking properties of blends of low-sulphur, high-volatile Illinois coal with the high- and low-volatile coals from the eastern fields. Such blends containing Illinois coal, if substituted for the all-eastern blends normally coked,

Jan 1, 1948

By W. M. Cross

Optical fibers have revolutionized the telecommunication industry, because of their ability to transmit large amounts of data over long distances. Without optical fibers many of the communication technologies on which business, industry and research rely would be impossible. In addition to their use as communication devices, optical fibers are often used as sensors. Despite the great promise that optical fibers have for the development of many types of remote sensing devices, few remote sensing devices have been built for use in the mineral industries. This paper will describe the use of optical fibers as sensors for surfactant adsorption at mineral surfaces.

Jan 1, 1995

By S. P. Ball

A major limitation to maximising the rate of gold extraction in commercial operations occurs as a consequence of the limited solubility of oxygen in cyanide liquors. The use of additions of solid inorganic peroxides as an in-situ supply of oxygen to the lixiviant has been studied, in particular in its application to heap leaching. Experimental studies showed-that the release of oxygen into solution from these peroxides is very sensitive to solution pH. Agitated leaching tests showed that, when either Ba, Ca or Sr peroxides were used as the-sole source of oxygen, both the rate and extent of gold extraccion was enhanced. Column leach tests were used to simulate heap leach conditions. These showed that significant increases in the rate of gold extraction could be achieved by additions of calcium peroxide, made to the ore, prior to it being loaded into the columns.

Jan 1, 1989

By H. W. Gussmann, R. G. Rohrs, E. van der Merwe

Salinity in Effluents carries a high penalty as a result of toxic­ity, corrosion, limited re-use potential, scaling and environmental impact. Although the high TDS, such as Calcium sulfate, other than metals are still being dealt with a low key non issue basis, they are receiving more and more attention from regulators. Traditional solutions to solve these problems are costly and inefficient and create therefore severe constraints on the prof­itability of mining operations and out-price in general the finan­cial resources for environmental clean up operations. Going up the technology versus cost curve the most econom­ic solution to pollution is dilution but which is difficult in a coun­t1y shoti of water. If this can't be done, the second best, at least in sunny areas, is, to pump the whole effluent on a tailings dam for evaporation. Depending on the contaminants, one may have to pond the efflu­ent to avoid re-dissolution and seepage into the ground. The next most common solution to pollution is the addition of lime to remove and concentrate any dissolved metals and then dump the product, hidden in a mass of gypsum in a convenient place. Again ponding may be required to avoid ground pollution. However the treatment costs start to rise steeply if it is not allowed to discharge the limed overflow solution because of its high calcium sulphate content. Further treatment is then required in the form of high cost and high tech membrane process tech­nology such as reverse osmosis or dialysis or even mechanical driven evaporation.

Jan 1, 1998

By Jorge Alberto Soares Tenório, Denise Crocce Romano Espinosa, Kellie Provazi

"The purpose of this paper is to study metal separation and recovery from a sample composed of a mixture of the spent household batteries main types, using liquid-liquid extraction and metals electroplating. The electrolytes preparation consisted: grinding the waste of mixed batteries, reduction and volatile metals elimination using electric furnace and acid leaching. From this solution were studied the liquid-liquid extraction using Cyanex 272 [bis(2,4,4-trimethylpentyl) phosphoric acid] with tributyl phosphate as extracting agent. After study of solvent extraction and stripping has been recover and separate the metallic ions and with electroplating was recovered the manganese, copper, nickel and cobalt in their metallic forms.IntroductionCurrently has increased the consumption of electronics devices such as mobile phones, laptops, wireless phones, comcorders, etc., especially portable devices that use batteries as a power source, and consequently has increased the disposal of such material.Increased consumption of this devices is caused by several factors including increased popularity of consumer electronics devices, has become essential of modem life. Therefore, recycling of batteries is important because its reduces the waste of raw materias and nonrenewable resouces used in manufacturing these materias and help prevent potential environmental risks associated with improper disposal of these products together with household garbage.The batteries have a very diverse composition, containing metals such as zinc, lithium, nickel, lead, mercury, cobalt, cadmium, iron, copper, manganese and rare earths. Some components may contain hazardous materials such as cadmium, mercury and lead, and can contain acids or bases.This research line is a pioneer in dealing with a single process for recycling a mixture with all batteries types, for only processes that exist in the world are based on the recycling a mixture with all types of batteries, for only processes that exist in the world are based on the recycling of one or two types of batteries [1-4]. This process necessitates the previous separation of the batteries by type."

Jan 1, 2012

By Don Painter, Nico Sutmoller, Lori M. K. Kahikina, Brian Dorwart

This paper will address the feasibility of using low-density cellular concrete (LDCC) for an annular fill application where project conditions required pumping the LDCC material for distances of up to 16,000 feet. These conditions occurred during construction of the Kaneohe-Kailua Sewer Tunnel in Oahu, Hawaii, between 2014 and 2018. Located on the island of Oahu, Hawaii, this 13-foot-diameter rock tunnel extends for approximately three miles from the Kaneohe Pre-Treatment Facility to the Kailua Regional Wastewater Treatment Plant. The tunnel was built to convey wastewater and provide temporary storage for peak wet weather flows entering the collection system, thereby reducing the potential for uncontrolled discharges. LDCC was chosen for this project partly due to its environmental benefits, which were essential for an application contiguous to the inland marine and coastal waters of the Pacific Ocean. In order to ensure optimal performance characteristics—compressive strength (with a requirement of 300 psi at 56 days), flowability, and light weight—were achieved, extensive testing of various LDCC products and mix designs was completed. The testing measured the initial set time of the LDCC as well as the compressive strength needed to reduce the quantity of grout lifts required for the project.

Jun 13, 2021

By K. U. Kainer

Magnesium and its alloys as the lightest available construction metal offer a wide range of opportunities for the usage in transportation industries, especially Magnesium wrought alloys with their improved mechanical properties show a high potential for structural applications, While magnesium cast components have found their application the interest is now spreading to wrought alloys due to the possibility to get even more homogeneous and better properties compared to cast parts, Therefore alloy and process development especially for extruded and sheet material is a main concern to enhance the application of Magnesium wrought alloys, Castings are still form the majority of applications of magnesium alloys, although efforts to develop adequate wrought alloys have increased, In the presentation, the alloy requirements for processing of cast and wrought alloys will be discussed, The various processing routes and alloy compositions result in specific microstructures and properties which determine the potential use of these alloys, Today, the spectrum of available alloys covers standard alloys as well as alloys for use at elevated temperatures, The trend will be to further diversify the alloy compositions and to improve the alloy properties, Areas of concern still remain the wrought processing and the high temperature (creep) and corrosion properties of magnesium alloys, Examples of recent developments in these sectors will be given, The presentation will also provide an overview of the historical and current use of magnesium and an outlook on future applications.

Jan 1, 2006

By J. H. C. Scrimgeour, T. Toong, R. E. Hamilton

"The principles involved in the use and application of mathematical models as an aid to the development of advanced process control computer systems are described briefly. This is followed by a brief survey of known models of this kind for the simulation of mining industry processes.The main part of the paper describes a dynamic model of the flotation process developed by Canadian General Electric. Using flotation rate constants for each species of mineral and gangue, the model provides a numerical solution of the differential equations describing cell behaviour. The cell mode] is used repeatedly as a subroutine in the •over-all-plant model. The features of the cell and plant models are described.Simulation runs from the plant model show stream .assays and other indications of plant behaviour printed typically in 1-to 10-minute steps for several hours of •Operation following typical disturbances such as changes in feed rate or reagent addition rate. The simulation can :Show expected behaviour for both uncontrolled and computer-controlled plants."

Jan 1, 1970

By Mark E. Gershon

The development of long term plans and schedules for strip mines now faces many companies, especially those developing large properties in the West. The rule of mining the lowest strip ratios first, while delaying equipment acquisitions and recouping investment the fastest, creates the situation where stripping ratios are too high in the latter years of mining operations. A program concept taking life of mine return on investment into account is developed in this paper to optimize mine scheduling and equipment acquisition. In addition, quality considerations (heat content, ash, sulfur, washability) can be considered by including the appropriate blending constraints to meet contract requirements.

Jan 1, 1983

By L. V. Chugaev, Y. M. Shneerson, P. V. Zaytsev, I. V. Fomenko, M. A. Pleshkov

"Pressure oxidation (POX) is one of the most common and reliable methods of processing gold-bearing sulfide concentrates. However, when processing concentrates that contain natural carbonaceous matter, substantial gold losses occur due to autoclave preg-robbing. The latter involves formation of gold chloride complexes under typical POX conditions (high temperatures, high acidity and high ORP) and subsequent sorption of these complexes by carbonaceous matter. Naturally, chloride ion plays a significant role in the process of autoclave preg-robbing; its concentration in POX solution has a well-marked effect on subsequent gold recovery during cyanidation of POX residue. The previous research done by SRC Hydrometallurgy showed that autoclave preg-robbing of gold could be significantly inhibited by the addition of mercury(II) compounds to POX slurry. The positive effect of mercury(II) was well pronounced both at high (>20 mg/L) and low (<5 mg/L) Cl concentrations in POX solution. The successful bench-scale laboratory testing was followed by pilot plant trials at Ore Test Facility in Blagoveshchensk, Russia. The present paper provides the results of these trials. The bench-scale testing results were verified; the optimum oxidizing parameters and reagent dosage were specified. The behavior of mercury (II) at POX pilot plant was found to be in good consistency with industrial practice described in the literature.INTRODUCTION Pressure oxidation (POX) is one of the most common, reliable, and commercially proven methods of processing gold-bearing sulfide ores and concentrates. However, when processing double refractory materials that contain natural carbonaceous matter, POX technology advantages are compromised by autoclave preg-robbing of gold. The latter occurs when natural organic carbon and soluble halides are both present in autoclave feed. Strongly oxidizing conditions of POX (high temperature, oxidation-reduction potential or ORP, and acidity) favor formation of gold-halide (mostly, gold-chloride) complexes, which tend to bond with carbonaceous matter. The exact nature and mechanism of this bonding is unknown, but as the result of this, cyanide is unable to leach gold from POX residue and the precious metal is lost to the tails (Axenov et al., 2014; Dimov, Chryssoulis, & Sodhi, 2003; Fomenko, Zaytsev, Pleshkov, Chugaev, & Shneerson, 2013)."

Jan 1, 2017

By Ernt. W. D.

A membrane based mixed extractant process was developed for selective removal of copper from waste acidic cupric chloride etchant solutions found in printed wire board manufacturing. The process uses a mixture of Adogen 381 (tri-isooctylamine), MOC®-45 (ketoxime) and MOC® 55TD (aldoxime) in a kerosene diluent. The mixed extractants recover the copper from a hydrochloric acid medium and transfers it to a sulfuric acid medium. The process also utilizes unique wetted membranes to separate the aqueous and organic phases. The driving force for these membranes is not pressure but the difference in surface tension between the two phases. By using these membranes, complete phase separation results. There is no physical entrainment contamination as found in conventional systems. The only cross contamination is the solubility concentration of one phase in the other. This however is less than 10 mg/l.

Jan 1, 1998