Search Documents

Laboratory testwork was carried out on an overall orebody composite, of 2.9 per cent Cu and 4.2 per cent Zn, prepared from drill core taken from the Currawong fine-grained, copper-zinc massive sulphide deposit near Benambra in Victoria. While 90 per cent of the copper was readily recovered in a concentrate of 20 per cent Cu, after grinding to 95 per cent passing 38 microns, zinc responded poorly to conventional flowsheet/reagent regimes. Experience elsewhere with the use of reverse cleaning, to separate pyrite from sphalerite, led to a series of tests in which better (but still modest)metallurgical results were obtained. The best result was a zinc recovery of 55 per cent in a concentrate of 50.5 per cent Zn. The major loss of zinc occurred in the reverse cleaning stage where the unit recovery of zinc was similar to pilot plant results achieved at Mount Isa Mines on similar feedstock. Diagnostic mineralogy suggested that an overall zinc recovery of 70 per cent was probably the practical upper limit, at a 50 per cent Zn grade.

Jan 1, 1999

It is very rare in the underground hard rock environment to find a deposit that is ideally suited to a specific mining method. Usually the irregular shape of the orebody will allow the deposit to be extracted by more than one mining method. During the prefeasibility stage, a number of conceptual mine designs are generally evaluated to see which offers the best method of extraction for the deposit. The selected method is usually based on key decision criteria such as the overall extraction of the orebody, the amount of metal produced annually and the unit cost of production. Often the prefeasibility study document will state that the project has an NPV of æxÆ million dollars. This statement can be made without any quantitative consideration of the likely risks of the mining methods reviewed or the level of confidence in the estimation of the NPV. By assigning a probability of failure to each component of the mining cycle a measure of the risk for each method can be determined. One mining method may provide the highest NPV when it is performing well, however, there may be a higher risk of a major failure impacting on the performance of that method, eg the failure of a mass blast of a crown or rib pillar. This paper will present a flowsheet approach to the use of risk analysis for determining the likely production rates of different mining methods. This framework allows the annual metal output to be estimated and from this the NPV for each method. A level of confidence can be applied to the estimated NPV for each option. An example will be presented on how this technique has been used within the Normandy Group.

Jan 1, 1998

By V. Quezada, Á. Astudillo, L. Valásquez, M. Garcia

Seawater has become a viable alternative for different uses in copper hydrometallurgy. In this paper we review the main physical and chemical characteristics of seawater and how these influence copper production. Reliable data on the use of continental water are reported, and the current use and consumption of seawater in the Chilean mining industry is analysed, indicating the main areas of use and the main problems encountered. Additionally, the influence of the elements in seawaterthat have the most influence on the extractive metallurgy of copper are considered. The Chilean copper mining industry currently consumes approximately 4.1 m3/s of seawater, which corresponds to 25% of the total water used. The use of seawater for the leaching of copper sulphide minerals, such as chalcopyrite, is beneficial because it provides 20 g/L of chloride, thereby improving copper dissolution kinetics.

Jul 5, 2023

By Paul Thurlow, Richard K. Lipscombe

The measurement of deflection of designed diaphragm walls is critical for near real time information to assess wall and soil behaviour as the internal area is excavated in a controlled manner. Data enables the site team and designers to check performance of the design, which is linked to safeguarding the site and the external stakeholders.This paper documents the use of Shape Accel Arrays at the Tottenham Court Road Western Ticket Hall during excavation and propping within the diaphragm wall for the Crossrail project. It shows how the data obtained was used within the site settlement management plan to assist in the control of the works and the information used for Value Engineering purposes that benefitted the project.The use of Shape Accel Arrays for measuring the deflection of retaining walls is not commonplace in the UK construction industry, with the Tottenham Court Road Western Ticket Hall being one of the first times they have been used in such a way. A detailed analysis of the data obtained from the instruments has been undertaken, and compared to the results obtained from the manual inclinometers that were read next to the SAAs. The advantages of the relatively new SAAs have been discussed, as well as other applications of the instrument.

Jan 1, 2017

By D. L. Romero

The Line Creek Mine is operated by Crows Nest Resources Limited, a wholly owned subsidiary of Shell Canada Resources Limited. It is located approximately 25 km north of Sparwood in southeast British Columbia (refer to figure 1). The Line Creek coal deposit is part of the Upper Elk Coalfield in the East Kootenays. The coal is a medium volatile, low sulfur, bituminous coal and is used as a coking coal. Coal close to the outcrop is typically of low F.S.I. and is processed for thermal use. The present pits have a total coal reserve of 30 million clean tonnes and is a multi-bench, open-pit operation. The coal is recovered by front shovel and backhoe combination, and hauled to the plant with a fleet of 120-tonne and 40-tonne capacity trucks. Line Creek is unique in that it can simultaneously treat both metallurgical and thermal coal in separate processing facilities (refer to figure 2). Run-of-mine coal is delivered to the truck dump. The plus 50 mm material is scalped off and reduced to minus 50 mm in two rotary breakers. The raw coal is then conveyed to one of five, 5000-tonne capacity, silos. Typically one silo is used for thermal coal and four for metallurgical coal (refer to figure 3).

Jan 1, 1991

By E. S. Malloch

THE Great War forced the peoples of the world to recognize the importance of the wise development and use of the world's natural resources. Not the least, and perhaps the most, important, is the world's fuel supply- solid, liquid, and gaseous. Without fuel our civilization would be impossible, and mankind would of necessity have to congregate in the torrid zones of the earth's surface for at least six months of every year. Of the three classes of fuels the solid ones are the most plentiful, as well as being the most widely distributed, since few countries are entirely devoid of solid fuels of one kind or another. Until a hundred years ago wood was the fuel most generally used in this country, but since then coal has supplanted wood as a fuel in all its uses, except in the outlying districts and among the farming communities. For many years the supply of coal was thought to be unlimited, but as years went by more thought and study were given to the world's coal resources, until today not only are the limits known, but in one instance at least their depletion is predicted to be almost within the age of living men, unless more provident methods are put into practice for their winning and utilization.

Jan 1, 1928

By P. L. Ngwenyama, I. Maubane

Soundless chemical demolition agents (SCDAs) are proving to be the future of sustainable and environmental-friendly mining. These expansive chemicals become critical when there is a need to break rock close to communities, environmentally sensitive areas, and critical structures and infrastructure. Unlike explosives, the SCDAs do not generate air-blast, ground vibrations, flyrock, noise, dust, and noxious fumes, which can negatively affect the environment, surrounding communities, sensitive areas, and critical structures and infrastructure. Over the years, several types of SCDA products have been used successfully in the civil and construction industries for the demolition of old and dilapidated buildings near vibrations and environmentally sensitive areas. They have also been used to fragment boulders in the mining and construction industries. However, to date, no study has investigated the applications of soundless chemical demolition on a large-scale in opencast mines. Therefore, this study evaluated whether soundless chemical demolition can break large volumes of in situ rock. This was done by conducting five trials using Nex-Pand soundless chemical demolition agents in four different surface mining sites. Trial 1 was unsuccessful as it was unable to break the rock due to the large confinement between the drilled holes and the use of a hole diameter that was 182% larger than recommended. Trial 2 was a success as it was able to fracture the rock with a crack width that reached 110 mm after 72 hours. Trial 3 generated cracks at the biggest hole diameter of 102 mm. The cracks developed and ceased to increase after 96 hours at a crack width of 100 mm. Trial 4 achieved the smallest crack width due to a very competent rock compared to the other sites. Trial 5 generated cracks at a slower rate than other trials because of the use of Nex-Pand powder at lower ambient temperatures than recommended. These trials proved that soundless chemical demolition agents can replace explosives in areas closer to sensitive infrastructure and communities. This will ultimately enable mines to unlock value and access deposits in these areas.

Jul 23, 2025

By Louis Frost

The coal-mining industry of Nova Scotia, particularly of the island of Cape Breton, today faced as no other industry with economic problems calling for progressive engineering with production on an economic basis, must soon enter upon a phase of reorganization wherein all factors conducive to the cost of producing coal relative to the prolongation of the life of the collieries with the ultimate winning of the maximum submarine area must be closely reviewed. Bearing this in mind and applying the process of elimination to coal-mining costs generally, we are left with only three channels through which we may approach the problem of cost reduction in producing coal: (a) intensive mechanization (b) reduction in the cost of labour (c) reduction in the cost of materials. Assuming that mechanization has reached an economic stage and that labour costs have reached an economic limit, we must turn our attention to the general material costs, which may be classified as 'live' and 'dead' costs. The former take in all things which can be accredited with a fractional depreciation and written off the balance sheet over a period of years. On the other hand, the ?dead'costs-of which the cost of supporting the underground workings form part must be completely written off: for these, no return may be expected, other than the economic return in the reduction of the cost per ton of coal produced.

Jan 1, 1928

By Harry Asche

Tunnels are frequently specified by owners to be designed to a structural code, often a bridge code. In the USA, AASHTO have created a tunnel code, based on structural principles, the AASHTO LRFD Tunnel Design Specification. The Load Resistance Factor Design method (LRFD) described in the AASHTO title is an approximation to the probabilistic design of structures, based on the independence of load and resistance. This methodology is well known to be problematic in geotechnical design, but it is widely used. The paper considers the difficulties of this approach and describes alternative approaches that would result in more appropriate designs for tunnels.

Jun 13, 2021

By Sibley C. Burnett

Early attempts to apply superconductivity to the beneficiation of kaolin required very large refrigerators to remove the heat generated during rapid charging and discharging of the magnet. In the early 1990's, Advanced Cryo Magnetics, Inc. developed and patented methods to reduce this pulsed heating by a factor of fifteen. Small, helium refrigerators and cryo-coolers are now used. Along with savings in electric power, superconductivity allows operation at higher magnetic fields and greatly improves separation process efficiency. New designs offer enormous reductions in weight, size and capital cost as compared to older copper magnets. Application of this technology to minerals other than kaolin is emerging.

Jan 1, 1999

By C. Flores

The most common experimental approach of studying one variable at a time while holding all others constant is extremely inefficient. Use of statistical methods enables engineers and scientists to obtain meaningful information with the fewest experiments, reducing cost and wasted effort. In particular, the Taguchi method can be more efficient than traditional full factorial experiment designs, as it can study more variables with fewer nuts, and it is more robust against process "noise." Taguchi designs are also simple to formulate and the results can be analyzed by simple PC spreadsheets. The role and benefits of using the Taguchi method in experiments to develop and optimize processes is discussed.

Jan 1, 1998

By C. O. Swanson

THE purpose of this paper is to discuss the use of the dip needle in the field of mining geology. The subject matter is new only to the extent that it reflects the writer' s added experience in recent years. The treatment is brief, and those interested in a more extended analysis are referred to the articles listed at the end of the paper. In the discovery and tracing of mineral deposits, the clip needle, like most other geophysical instruments, can be used in two ways. One method may be termed direct; the other, indirect. The direct method is that of finding or following certain ore-bodies by virtue of their magnetic properties. Explicitly, or by inference, it is the method which many mining men and practising geophysicists have in mind when they consider whether or not a certain property should be studied by geophysical means. In the ideal case, this method demands little or no knowledge of geological conditions. The indirect method uses the clip needle as an aid to purely geological studies in working out the structure of a mineralized area. Although not as simple as the direct method, it enjoys a much wider field of usefulness. The writer's experience in the past fifteen years, which is believed to be typical, is that the indirect method finds application four or five times as often as the direct method. The indirect method is of particular value because it furnishes information concerning the relationship between geological structure and ore occurrence. Most mining engineers will agree that structural control is an important factor in the localization of ore deposits, and therefore that the subject under consideration is of some interest in mining geology. Specifically, then, the present purpose is to outline the principles and practice of using the clip needle in working? out geological structure.

Jan 1, 1941

By A. W. Bryson, S. P. Fox, S. A. Godorr

"This work is an extension of a previous investigation on the development of surface roughness during electrodeposition of copper. A comprehensive model based on diffusion and migration in a force field together with surface diffusion and sticking probabilities is used to generate profiles which are compared to those produced experimentally. The roughness is characterized by using the technique of fractal geometry which is shown to describe both qualitatively and 9uantitatively the development of surface morphology during electrodeposition.The work is extended to the deposition of copper in the presence of various concentrations of thiourea. The development of roughness is observed experimentally on the edge of a thin copper disc mounted between two glass plates. This enables photographs to be taken at various stages during growth. The surface outline is digitized using an image analyzer which enables the fractal dimension to be determined as growth proceeds. As expected, the presence of thiourea at low concentrations produces a fractal dimension which is closer to unity (i.e. the surface becomes smoother).IntroductionThe development of surface morphology during electrodeposition has far-reaching implications for copper plating in the electrowinning and electrorefining processes. Short circuits as the cathode surface grows unevenly require operator intervention in a dangerous environment and imply processing delays, and the inclusion of electrolyte in small gaps in the plated cathode have implications in downstream processing of the cathode. Higher current densities are obviously desirable, as they result in greater production rates, but as shown by Ettel et. al.(l), Harvey et. al.(2), Cook (3), and Harvey et. al.(4), it is not possible to operate near the projected economically optimum conditions because the electrodeposition of copper from sulphate and acid solutions is a mass transfer controlled process. It has been shown (Ettel et. al.(l), Harvey et. al.(2)) that the closer a system operates to mass transfer limiting conditions, the poorer the resulting cathode quality. One solution is to use agitation techniques to increase the limiting current density. Another is to add surface active additives to the electrolyte which has been shown by Ettel et. al.(l), Harveyet. al.(2) and Afifi et. a1.(5) to allow higher rates of production without decreasing cathode quality. The second proposed solution is of interest in this work, since there is very little knowledge of the conditions under which these additives operate effectively, and little fundamental understanding of the mechanism by which they operate. The current work seeks to contribute to this field by correlating a simulation model with experimental results to describe the development of surface morphology in the electrodeposition process."

Jan 1, 1997

By P. G. Hallof

The exploration staff of Campbell-Chibougamau Mines Limited has used past experience to delineate several areas of geologic interest under Lake. Chibougamau. Du• ring the winter of 1964-65, a reconnaissance induced polarization survey was carried out on the lake. First, several lines were surveyed over the known mu1.erahza-tion at the Henderson mine; the grid was then extended into the areas of interest. Several anomalous zones were located and drilled; one, of these proved to be of economic interest.

Jan 1, 1967

By A. C. Ross

"The paper will deal with non-destructive testing in general, and its advantages to those responsible for the maintenance of wire rope. An outline of the main features of the M.D. 6 Defectograph will be given, and the method of operation and results obtained will be described.The instrument will accommodate ropes at 7 /16-to 2 %-inch diameter at reasonable speeds, and is capable of detecting the most minute defects in even the largest-diameter wire ropes."

Jan 1, 1969

By D J. Brake

Faced with the need to improve workplace conditions in both its development and production headings in its existing K1 orebody, as well as its new K Link and K2 orebodies, the Kencana mine in Indonesia took the novel approach of reversing the ventilation on most of its access ramp by outcasting up the ramp to the portal. Working levels were then fed with fresh air via auxiliary fans sealed into the current surface ‘egress’ intake raises (ladderways) or another small surface intake raisebore rather than from fans hung in the ramp as in the past. Outcasting the portal provided a substantial increase in the total mine exhaust capacity allowing fewer levels to be ventilated in series and significantly improving conditions, especially in the most difficult workplaces to ventilate. It also reduced the consequences if there was to be a fire on a vehicle in the ramp. The same system using the ramp as an exhaust is also intended to be used as part of the final ventilation solution for the new K2 orebody which also uses a novel single surface ventilation shaft that is vertically split into separate intake and exhaust compartments using a concrete brattice. Using the main ramp as an exhaust has potential application in many other operations in Australia using surface ramps which otherwise frequently suffer from overuse of series ventilation circuits and poor working conditions at the mine bottom.

Mar 21, 2011

By Richard L. Werner

The petrographic microscope as a tool in determining impurities and grain size of limestones, clays, sand and coal ash for possible use as raw materials is discussed. Its use in the determination of the mineral composition of various size fractions of the raw mix, after fine grinding in ball mills, and of the waste dust from the rotary kiln. A description is given of the typical clinker crystals; alite, belite, tricalcium aluminate and ferrite. The process problems indicated by various changes in the crystal characteristics are listed with possible solutions. Finally the microscope as used in relation to field problems with concrete such as air void volume, percent hydration of the cement, cement aggregate bonding and the determination of solid additives, is presented.

Jan 1, 1982

By Sorokin M, Komkov A, Fyodorov A

The Vanyukov Process is a high-intensity smelting system that has been proven over the last 20 years for various metallurgical operations including the smelting of copper, nickel, copper-zinc, antimony concentrates, municipal waste treatment and pig-iron production. Extensive pilot plant tests on copper and copper-nickel concentrates have provided information for the design of the commercial furnaces. The thermodynamic analysis, design idea and the data obtained from commercial furnaces have shown that Vanyukov Process would be the best choice to smelt copper-nickel and nickel sulphide concentrates as well as oxide nickel ores.

Jan 1, 1996

By Denise C. R. Espinosa

The amount of secondary batteries are increasing about 15% by year. Among these batteries, it can be highlighted the NiCd ones, due to their high consumption. In Brazil, the consumption of NiCd batteries grown quickly in the last 5 years, due to the dissemination of cellular telephones and other electronic devices. The first step of a process to recycle spent NiCd batteries is the pretreatment through unit operations of mining treatment. The aim of this work is to define a physical pretreatment to conditioning the waste to a pyrornetallurgical recycling process of spent NiCd batteries used in cellular telephones. Batteries were disassembled by hand to release the different components. The studied batteries are basically composed (by weight) of: 78% nucleus, 18% plastic case and 2% circuits. The grinding of the batteries was performed by knife mill and also by hammer mill. After grinding the material was screened and submitted to a magnetic separator.

Jan 1, 2001

By C. Birch, M. Katuruza

"The purpose of this study was to demonstrate unmanned aircraft system (UAS) technology in opencast highwall mapping using the experience at Isibonelo Colliery in Mpumalanga Province of South Africa. In opencast mines, geological mapping has evolved over time and there have been challenges in extracting valuable information from exposed highwalls due to restricted access for safety reasons. A UAS was used at Isibonelo Colliery to conduct highwall mapping, using drone-based digital photogrammetry techniques. A demonstration survey was undertaken during February 2018. The highwall flyover demonstration was planned for two areas (North and South pits) where field control points were placed by the mine survey department. A contractor used a DJI Phantom 4 (Pro) for the highwall mapping. Raw data was processed within 48 hours and a 3D model of the mapped pit area was produced. Further data extraction included obtaining updated weathering and lithological contact elevations and thicknesses for use in short-term planning. The results showed a good correlation between the resource model and the UAS data model. The project was considered a success and highwall flyover mapping and is now standard practice at Isibonelo Colliery.IntroductionDetailed geological mapping is crucial to the understanding of the structure of any mineral deposit. Several mapping methods may be applied depending on the available exposure/outcrop and nature of the orebody; for example, coal deposits typically suboutcrop only, therefore an opencut highwall provides the best exposure for mapping the geology. Mapped information, when incorporated into a resource model (generated from exploration borehole data), improves the understanding of the orebody or coal seam. This research paper focused on the use of unmanned aircraft system (UAS) technology for pit highwall mapping to generate data for updating geological models and avail the latest information to mine planning to improve the short-term plans."

Mar 1, 2019