Search Documents

By W. A. STERLING

IN the opencut iron mines of the Mesabi Range in Minnesota, the trend in mining is in the development of mining equipment and mining methods which will move surface overburden and ore-bearing materials with less labor and at a cheaper cost. This is a must for most of the independent operators. Their reserves of direct-shipping ore are extremely small and their operations are being conducted in small, or intermediate pits, with a high stripping ratio in the outer fringes, or shore lines of older pits. and in ore bodies passing from direct shipping to the washing and the intermediate, or retreat ore state. The trend is toward deeper stripping, longer and steeper hauls, and the necessity of moving a total of from three to five or six tons of overburden and ore material for each ton of shipping-grade ore produced. This naturally calls for greater production, with larger shovels, or draglines. cheaper drilling and blasting costs through the drilling of larger-diameter blastholes, and cheaper haulage through the use of trucks of larger capacity and more extensive use of belt-conveyor systems. This trend is notable both in stripping and mining.

Jan 1, 1948

By Claus G. Goetzel

POWDER metallurgy is known as the art of producing metal powders and fabricating them in a nonfusion process by a simultaneous or consecutive application of pressure and heat under controlled operating conditions. Before the advent of powder metallurgy, the high melting points of the refractory metals and nonmetals made their manufacture and use practically impossible. Today, however, the uses of refractory materials in high-speed cutting tools, surgical instruments, brake linings, electrical contact switches, and filaments in incandescent lamps are commonplace in industry. Lately designers have even been turning to powder metallurgists to develop new techniques of fabricating refractory materials for extreme-service use in high-temperature zones of such modern products as gas turbines and jet engines. The new techniques being born will undoubtedly provide industry with a great number of new alloys and materials for future designing.

Jan 1, 1948

By L Clarkson, D Williams, P Redcliffe, F van der Wal

This research presents a snapshot and insight into the trends, patterns, and common considerations identified in the current standing of real-time tailings dam monitoring practice. Based primarily on information derived from concurrent research by the author (in form of a Catalogue of Real-time Instrumentation and Monitoring Techniques for Tailings Dams), challenges and opportunities when transitioning to a real-time monitoring system are discussed. Learnings and key considerations between different monitoring approaches are explored, including themes of limitations and advantages that were observed consistently through global supplier feedback.

Jul 1, 2021

By Anson Hayes

FOR the purpose of the following discussion the word "research" is interpreted as including all phases of development work on methods of manufacture, metallurgical characteristics, and uses of iron and steel. Research in the iron and steel industry then includes both plant re- search and laboratory research. Since iron and steel came into being, the steel consumer's plant and the steel producer's plant have been important factors in the development of the steel industry. Good minds have always been associated with both consumer and producer plants, so marked progress was made in the industry even when these were the only types of research and development groups in action.

Jan 1, 1937

By J. B. Offei, K. Awuah-Offei

Mining companies registered with the SEC were required to comply with Regulation S-K 1300 for their annual report covering the first fiscal year ending on or after January 1, 2021. Consequently, most mining registrants filed their first S-K 1300 compliant disclosures in 2022. The US Securities & Exchange Commission (SEC), as part of its disclosure review program, has been issuing comment letters in response to these filings. This paper presents an overview of the trends in these comment letters. The authors reviewed comment letters retrieved from the SEC’s EDGAR database based on Standard Industrial Classification (SIC) Codes that cover mining, the content of the comment letter (whether it references S-K 1300 or not), the names of SEC staff listed in the comment letters, and other criteria. The analysis shows the SEC staff's reviews have been comprehensive covering the breadth of S-K 1300 and eliciting compliance with the rule. The staff through their comments are eliciting all the disclosures required by S-K 1300 and are not allowing registrants to substitute disclosures based on other standards for S-K 1300 disclosures. It is important, however, not to over generalize as the comments are based on the particular context.

Feb 1, 2023

By A. Bauer

This paper describes the trends in recent years in explosives formulated to produce larger blast-hole spacings and over-all lower drilling and blasting costs in hard formations. A consideration of current rotary drilling costs per ft of hole and per ton of muck versus hole diameter indicates that it is now possible that we shall see much further use of lower-energy-content, lower-cost slurries and dry mixes, and larger-diameter and, in many instances, cheaper blast holes. These will be drilled on current or slightly larger blast patterns to yield the same energy input per ton of rock and similar fragmentation at lower costs.

Jan 1, 1968

By F. T. M. White, W. A. Bardswick

"The parameters of airborne minerallic particulates which create industrial dustiness, together with the physiological hazards caused by their inhalation, are reviewed. Various techniques of dust sampling are discussed and analysed, and the parameters referred to above are classified as the basis for methods of assessing the physical, chemical and mineralogical characteristics of dust-particle suspensions. The paper surveys those methods of assessment currently accepted by various statutory authorities, and reviews other methods that warrant attention and newer techniques that are being developed."

Jan 1, 1969

By T. R. Ellis

Regulation of mineral property valuation methodology by governments and others is due to frauds, condemnation and takings, banking industry problems, and litigation. Definitions of "reserves," "resources," and "qualified person" continue to evolve, along with guidelines to the data and disclosure required to support valuations. A less recognized but vital issue relates to the regulatory acceptability of alternatives to the comparable sales method. Comparable sales generally work well for surface real estate, and sometimes for precious metal deposits, but not at all for most industrial mineral properties. Alternative methods, such as net present value, or a geoscience rating system, often provide better valuations. Yet US regulations dictate comparable sales as the preferred method. The task of convincing regulators of the inapplicability of comparable sales to mineral properties, particularly those lacking reserves, may be as important as the valuation itself.

Jan 1, 1999

By HAROLD A. TITCOMB

TOWARD the close of 1925, a British geologist, T. Landell Mills, brought to the notice of .A. Chester Beatty and selection Trust Ltd. certain mineral areas in southern Yugoslavia. Mills' data, which included rough maps and preliminary reports by' a Yugoslav engineer, Jules Draskocy, appeared interesting to Reatty, and early in 1926, I, with three British assistants, proceeded to Serbiaand commenced the investigation of several groups of ancient mine workings. They were found to be extensive and the geological conditions-schists, limestones, and andesitic intrusive-favorable for mineral deposits. At Stan Trg, on the Trepca Concession, five rniles east of Kosovska Mitrovica, an ancient filled adit was found, a shelter-hut erected, and work started in reopening this adit.

Jan 1, 1936

By James Lorimer

THE topography at the Stan Trg mine facilitated early exploration by adits; in consequence adit levels were developed at horizons 865, 795, and 760 meters above sea level, and the levels in the mine 'are named according to their elevation. Exploitation started from the 760-m. level . upwards while simultaneously first steps were taken with regard to mining in depth. A deep dewatering adit 2.5 km. long now gives access to the deposit at the 610-m. horizon which also is connected with the 760-m. adit level by a three-compartment main hoisting shaft. Main levels have been developed internally from

Jan 1, 1936

By G. Ferrara

During several years of operation in Europe, South Africa and other countries, the Tri-Flo has demonstrated to represent a substantial improvement of the dense medium dynamic separation systems. The reasons are: (1) high sharpness separation due to the multistage system and the application of new concepts in designing the regeneration circuit and controlling the medium rheology; (2) the possibility of performing two cuts at different densities using a since separation device and a single regeneration circuit. The paper discusses in detail the above mentioned points, with particular reference to the multistage technology, based on the circuit analysis theory, and to the control of the medium rheology based on recent work in the modelling, and simulation of the rheological behavior of dense suspensions.

Jan 1, 1993

THE Fall Regional Meeting of the Institute, which has now for some years been held in cooperation with the Western Division of the American Mining Congress, will be held this year at Joplin, Mo., in the heart of the great Tri-State district. This year the Tri-State Zinc and Lead Ore Producers Association is joining in the meeting. The Society of Economic Geologists will also take part though not offering any papers. The district in which the meeting is held includes adjacent parts of Missouri, Kansas and Oklahoma. Out in the heart of a fertile prairie farming country, it is one of the major mining districts of the world. It produces normally approximately one-third of the zinc ore mined in the United States which is equivalent to nearly one-half the zinc since the concentrate has always been notable for the height of its grade. Even in the depressed business year 1930, the American Bureau of Metal Statistics credits the district with 434,460 tons of concentrates equal to 217,230 tons of zinc out of 1,503,095 and 576,630 respectively for the country as a whole. This was equal to about one-seventh of the world's output of zinc, more than that of any foreign country. In addition about 75,000 to 100,000 tons of lead is annually furnished by the same mines. Elsewhere we present a general description of the district prepared for this meeting by J. C. Heilman, a Lehigh graduate, who has spent the past eleven years there and has had charge of explorations for many of the companies.

Jan 1, 1931

By H. Ogasawara

Information on rock stress is important for safe mining in seismically active ground. On a major gold mine, a few tens of crews are continuously conducting geological drilling with small pneumatic machines. However, stress measurements are not often carried out in South African deep-level gold mines. One of the reasons is the drilling diameter that overcoring requires, which is much larger than the diameters used in regular geological drilling, e.g. Boart Longyear Metre Eater, which drills AQ or BQ holes. Larger diameter holes result in slower drilling advance, more load in transportation and handling at sites, and higher cost. In order to enable overcoring in BX size (60 mm diameter), we modified the compact conical-ended borehole overcoring (CCBO) technique that has been suggested by International Society for Rock Mechanics (ISRM) and was originally designed for NX drilling (76 mm diameter). With a single overcoring, the 3-D stress tensor can be determined. We tested this modified method at a depth of about 3 km at Moab Khotsong mine in South Africa. We worked with drilling crew who usually work at geological drilling with the Metre Eater. In January 2011, we tried using regular geological drilling tools (a sequence of a normal BX bit, reamer, and rod) without success. In August and September 2011, introducing stabilizers and thin BX bits, we succeeded. We could complete a cycle of procedures necessary for an overcoring, including shaping the borehole-end conically, glueing a 16-element strain cell, and overcoring, within 2.5 hours. Only 10 cm overcoring is needed, which increases the chance of successful overcoring in heavily fractured conditions. This modified method is suitable for up-dip holes to depths of 10-15 m from tunnels, and has the potential to be widely used at the initial stage of geological exploration drilling at many localities.

Jan 1, 2012

By R Steven

"Surveying, and as a result, surveyors, have been around since the start of time, and it has been said that so has their methodology!The theodolite and tape have been the backbone of a time-tested practice that has led to ground breaking advancements such as electronic distance measurement (EDM), global positioning system (GPS) and positional laser scanning. However, it was the introduction of the unmanned aerial system (UAS) that has allowed mine sites such as St Ives to take the next step towards truly turning survey data into metadata.This paper will explain how the unmanned aerial vehicle (UAV) was adapted to meet the requirements of a mine site supporting a major open pit operation, and how the open pit mining team adjusted their planning and production processes to maximise use of the extra data and information available to them.The advantages of the system include point cloud surveys with corresponding large-scale up-to-date photography and computer generated high detail contouring of mined areas that are then incorporated into the mine plan. All the while, the use of the UAV must be tailored to each specific problem encountered and a solution then matched.Citation:Steven, R, 2016. Trials, Tribulations and Triumphs of Unmanned Aerial Vehicle Surveying at St Ives Gold Mine, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 170–184 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By Stephen A. Gasiorowski, Frank J. Hrach, James D. Bittner

Separation Technologies, LLC (ST) has developed a processing system based on triboelectric charging and electrostatic separation that provides the mineral processing industry a means to beneficiate fine materials with an entirely dry technology. The environmentally friendly process can eliminate wet processing and required drying of the final material. The process requires little if any pre-treatment of the material other than grinding and operates at high capacity - up to 40 tonnes per hour by a compact machine. Energy consumption is low, approximately 1 kWh/tonne of material processed. Since the only potential emission of the process is dust, permitting is typically relatively easy. In contrast to the other available electrostatic separation processes that are typically limited to particles greater than 75 µm in size, the ST belt separator is ideally suited for separation of very fine (<1 µm) to moderately coarse (500 µm) materials with very high throughputs. The triboelectric particle charging is effective for a wide range of materials and only requires particle-particle contact. The small gap, high electric field, counter-current flow, vigorous particle-particle agitation and self-cleaning action of the belt on the electrodes are the critical features of the ST separator. The high efficiency multi-stage separation through charging / recharging and internal recycle results in far superior separations and is effective on fine materials that cannot be separated at all by the conventional electrostatic techniques. Since 1995, this triboelectric process has been extensively used for the beneficiation of coal fly ash with eighteen separators in place and over 100 machine-years of operation at locations in North America and Europe. The technology has been also successfully applied to the beneficiation of a variety of minerals including calcium carbonates, talc, and potash.

Jan 1, 2012

By Hamid-Reza Manouchehri

"The triboelectric charge attributes of feldspar, quartz and wollastonite minerals, after contacting different triboecharging medium made of different materials, were considered. Their charge acquisitions by different size fractions of minerals were monitored and accordingly their energetic work function values were estimated. Moreover the separation behaviours of these minerals through the electric field of a laboratory free falling separator were determined and the effects of some chemical reagents on separation their separation characteristics were studied.Finally an attempt was made to translate the findings from single mineral systems to a complex silicate ore, containing quartz, feldspars, wollastonite and some other silicates. The results show favourable prospect to apply the triboelectric separation technique for beneficiation such a complex raw material."

Jan 1, 2003

By Xing Yang, Zhen Peng, Guangwen Zhang, Haifeng Wang, Yaqun He

"Triboelectric separation of ilmenite ore based on the tribocharge differences between ilmenite and gangue minerals was conducted in this study. Triboelectric characteristics of ilmenite and its associated minerals were studied using polyvinyl chloride (PVC), pentatricopeptide repeats (PPR), copper, polymethyl methacrylate (PMMA), stainless steel (SS), teflon and quartz glass (QG) tribochargers in lab triboelectric unit. Results demonstrated that the ilmenite particles tribocharged positively while gangue minerals tribocharged negatively using PVC as tribocharger. The particle size also has a significant effect on tribocharge, and the -0.125+0.074 mm is the optimal size fraction of triboelectric separation. Charge-mass ratios of minerals increase with the increases of tribocharging length, but the increasing rate gradually reduce. At 1.5 m tribocharging length, charge-mass ratios of ilmenite, quartz, feldspar and mica are up to 6.07 nC/g, -6.05 nC/g, -4.30 nC/g and -4.56 nC/g, respectively. Based on the triboelectric characteristics of each mineral, triboelectric separation of ilmenite was conducted, and the grade of ilmenite ore increased from 15.47% to 28.40%. INTRODUCTION As a transition metal titanium plays an irreplaceable role in medical, aerospace and materials due to its light weight, high strength and corrosion resistance. Pure titanium dioxide is an excellent white pigment and is widely applied in industries of paint and textile. Ilmenite is the main raw material for titanium industry. For the beneficiation of ilmenite, series methods have been proposed, such as the application of dry magnetic and wet gravity separations to separate the ilmenite from the zircon and rutile. Electrostatic separation is extensively used in the beneficiation of heavy mineral sands for the recovery of rutile, zircon and ilmenite while flotation is used to separate fine ilmenite (Mehdilo et al., 2014; Fan et al., 2014). Compared with flotation and gravity separation, electrostatic separation does not consume water, and native properties of materials will not be changed and energy consumption will be reduced (Wang et al., 2014). Thus, the wide application of electrostatic separation and other dry separation methods is a trend in separation and purification industry, especially in water-scarce areas."

Jan 1, 2018

By Nicolás Ariel Zabala

During the make-up and break-out of the connections, threaded joints are exposed to intense mechanical and tribological solicitations. The connection performance is influenced by its geometry, material properties, surface treatments and thread compound. The aim of this work is to evaluate and characterize the tribological behavior of different thread compounds applied on manganese phosphated carbon steel under low speed and high pressure sliding contact. Four thread compounds were evaluated: one containing lead, zinc and graphite; other lead-free, containing copper and finally, the last two lead-free and containing non-metallic solids. The tribological behavior was analyzed by a block-on-ring tribotest. During the test, load varied linearly between 250 N and 7000 N; loading and unloading lasted 14 sec and were performed in opposite directions of rotation to simulate the make-up and break-out operations. Friction force and load as a function of time were registered. Upon completion of the test, wear surfaces were analyzed by SEM, optical microscopy and energy dispersive spectroscopy. The obtained results show that the lead and zinc containing thread compound displayed the best behavior, showing a wear reduction of approximately 20%. These results are in line with previously known oilfield experience. Average COF values around 0.15 were measured and no significant differences between dopes were observed; indicating that the wear behavior was influenced by the additive package.

Jul 31, 2018

By J. Molgaard, J. Masounave, J. Prinsen, P. Beaulieu, G. Huard

"A study carried out on behalf of the National Research Council (NRC) indicates that economic losses due to wear in the Canadian mining industry are in excess of $700 million annually. Severe wear, mainly by abrasion, was identified as the most important wear mechanism in terms of possible savings. One way to reduce losses would be the proper use of databases. A joint project of The Canadian Institute of Mining and Metallurgy (CIM) and NRC (Tribology laboratories at IMRI) has been initiated to create a factual database containing all relevant experience in the area of wear in the Canadian mining industry. As a first step, a prototype covering slurry pumps is being built. This should help to answer many questions, such as the number of people involved, interest from industry, cost vs benefits, etc.IntroductionTribology is concerned with the understanding of the mechanisms of friction, wear, and lubrication.Tribology is concerned with the correct use of materials for interacting solid surfaces, with the interaction of those surfaces with lubricants, with the chemistry, physics and use of lubricants and their additives. It is concerned with the reduction of friction and wear (or, in the case of belts, brakes, clutch plates, and similar devices, in achieving optimum friction with minimum wear) and is concerned with the avoidance of associated failures in machinery.Lubrication is usually the solution to a problem of friction and wear. Yet far from all the problems of friction and wear are solved by lubrication. The wear of grinding rods or shovel track pads can hardly be solved by lubrication, to name just two examples with which mining engineers will be familiar. There are indeed many situations of wear and friction where the surfaces in contact are unlubricated.In part, tribology is a matter of design. A major aspect, however, has to do with the choice of materials, to satisfy external constraints upon the component design or choice. The operating conditions for much industrial equipment, particularly in mining are, often very severe. The development of wear resistant materials, including materials which are applied as coatings, is clearly an important technology from the point of view of tribology."

Jan 1, 1987

By Jesús A. Carlos Cornelio

Since their discovery in 1991 Carbon nanotubes (CNTs) have attracted much interest due to their remarkable mechanical, thermal, electrical, chemical and optical properties. In connection with their mechanical properties, CNTs have been studied in various forms for tribological applications including their use as lubricant additives for oil and water. In this paper the tribological properties of CNTs (SWCNTs and MWCNTs) when used as lubricant additives are studied under rolling-sliding conditions in a twin-disc testing machine. The tests were performed using 5% of creepage and pressures of 0.8 GPa and 1.1 GPa. Used functionalized nanotubes were modified with carboxylic acid ultrasonically dispersed at different concentrations (0.01, 0.05%). The results indicated that the presence of carbon nanotubes leads to a decrease in both friction coefficient and wear rate for both systems studied (oil and water).

Jul 31, 2018