Search Documents

By Howard Drullard

To OBTAIN the best results from hammer drills, close attention must be paid to two factors in drill maintenance, which are of equal importance; one is lubrication, the other is the shank. With the exception of stoping drills, most modern rock drills require both oil and grease. The oil ports are in the lubricator, on or behind the hammer cylinder; the grease port for the lubrication of the 'chuck sleeve and rotating mechanism is on the chuck end. Ordinary machine oil is not, adapted to rock drills; a heavier more gelatinous oil such as castor machine oil or liquid-grease should be used. The lubricators should be filled-once for every 12 or 14 ft. (3.5 to 4m.), of hole drilled. Grease-guns should be used to fill the port in the chuck end once a shift; a medium ( No. 3) grease is well adapted to this purpose. Hard grease must not be put into- the lubricators, as it will not flow through that part. Contrary to the popular belief, oiling a machine once or twice a shift does not provide sufficient lubrication; the drills should be oiled once for every 12 or 14 ft. of, hole drilled. The rotating handle of a stoping drill -is an oil reservoir and is provided with a port for oiling. The rotating handle is packed with wicking, or similar material, which causes the oil to feed slowly from the handle to the other parts of the machine. Stoping drills require oil at. least twice a shift; lighter oils than castor, such as Arctic Ammonia may be used.

Jan 8, 1920

By L. V. Bell

"The gold deposits of the Caribou mine are representative of those of the Province of Nova Scotia as a whole. The ore shoots within the deposits, in common with those elsewhere within the Province, are associated usually with interruptions or irregularities in the broader and uniform fold structures. The structural factors localizing ore deposition as applied more specifically to the Caribou mine are demonstrated chiefly by the close relationship of the two principal ore shoots, known as the main orebody and the 'high-grade' vein, with a pitching drag fold developed in the southeast limb of the major northeast-southwest trending anticlinal fold or elongated dome that constitutes the primary structural feature of the Caribou gold district. It is of interest to note that the evidence indicates that this drag fold, in common with other folds subsidiary to the primary fold, formed as a result of movement similar in nature to that which caused the primary fold itself. Presumably, therefore, these folds are coincident in time.The property described here as the Caribou mine is an amalgamation of two adjacent properties formerly known as the Ross and the Nova Scotia Gold, but which since 1934 have been controlled and operated as a unit by The Consolidated Mining and Smelting Company of Canada, Limited. The Caribou mine is situated in the Caribou gold district about 45 miles to the northeast of the city of Halifax and about 6 miles to the north of the Moose River gold district.The history of mining at Caribou dates back to 1867. The first recorded gold production is for 1869. From 1869 to 1933 the gold produced from the mines of the Caribou district aggregated 47,249 oz. from 93,234 tons of ore treated. The grade of the ore on the basis of the gold actually recovered from the district would thus average 72 oz. gold a ton, which, as will be noted from the following, is precisely the grade of the ore treated from the Caribou mine during operations by The Consolidated Mining and Smelting Company. These operations commenced in September, 1934, and milling on a commercial basis was under way during 1938. Since that time production, apart from a short period in 1945 during which efforts were concentrated on development work, was continuous to early in 1947, when the mine closed down owing to exhaustion of the known orebodies. Gold produced from the Caribou mine by The Consolidated Mining and Smelting Company from September, 1934, to the close of 1946 aggregated 43,205 oz. from 90,754 tons of ore milled; the grade of ore treated averaged 0.50 oz. gold a ton. The indicated average grade of O.S oz. gold a ton for the ore of the Caribou district throughout its mining history ranks somewhat higher than the 0.37 oz. a ton average for the ore milled to date from the several gold districts throughout the Province as a whole according to the production statistics of the Provincial Department of Mines."

Jan 1, 1954

By F. Habashi

"The rare earths industry started in Austria in 1887 by Carl Auer von Welsbach (1858-1929) Professor of Chemistry at the University of Vienna. The process was based on monazite sand transported from Brazil as shipping ballast free of charge. This made possible producing thorium, cerium, and other rare earths at a low cost, thus permitting the growth of the industry. However, once the Brazilian authorities realized the strategic importance of the sand, shipping was stopped. Brazil then started its own processing of the sand in 1949. The background for Auer’s work, the role of Robert Bunsen in Heidelberg, and the invention of the spectroscope will be presented. INTRODUCTIONHeidelberg on the Neckar (Figure 1) was the meeting place for chemistry students from all over Europe in the nineteenth century. Her university founded in 1386 had already a famous professor of chemistry and medecine in the Faculty of Medicine by the name Leopold Gmelin whose three - volume Handbuch der theoretischen Chemie appeared in 1817-1819, that became later a multi-volume monumental work. As successor to Gmelin came Robert Bunsen (Figure 2) in 1852 who made this university town the Mecca of chemistry students. One of his students, the English Henry Roscoe (1833-1915) who became later a distinguished professor in Manchester, described him as follows: ""As an investigator he was great, as a teacher he was greater, as a man and a friend he was greatest""."

Jan 1, 2012

By C. S. R. Rondestvedt

In February 2010, Teck?s newest Concentrator at Mina Carmen de Andacollo (CDA), Andacollo, Chile was commissioned. The Concentrator is a single line configuration, comprising of one 36 ft diameter x 20 ft long SAG mill driven by an 18,000 hp gearless drive. The SAG mill feeds two ball mills each 25 ft in diameter x 40.5 ft long, each driven by a total of 19,000 hp through dual pinion drives. A series of four phases will be reviewed from operational readiness, mechanical completion, commissioning, and ramp-up. Also, now after 6 months of operation, this paper will review the significant steps taken during ramp-up enabling the announcement of commercial production, in October 2010.

Jan 1, 2012

By M. Yamine, R. J. Ring, D. J. Waters

"An experimental program has been carried out by the Australian Atomic Energy Commission to compare the effectiveness of Caro's acid as an alternative oxidant to pyrolusite in the leaching of uranium ores from the Alligator Rivers region of northern Australia. Batch leaching tests on Ranger, Nabarlek, Koongarra and Jabiluka ores showed that uranium extraction was unaffected by choice of oxidant, but that Caro's acid reduced acid requirements by 15 - 25%. Lime requirements for neutralization of tailings liquors were reduced by 20 - 30%.The batch studies were extended to a four-stage continuous leaching circuit with a capacity of 400 gore h-I. Comparative leaching tests confirmed the reagent savings obtained in the batch tests. Following these encouraging laboratory results, lnterox Chemicals Pty Ltd carried out plant trials using Caro's acid. Reagent savings in the mill were similar to, or better than, those obtained in laboratory test work. The trials also established that Caro's acid has a number of operational advantages over pyrolusite.IntroductionUranium is most commonly extracted from its ores by leaching in sulphuric acid. Simple hexavalent uranium oxides and compounds are readily soluble but uranium in the tetravalent form is insoluble and must be oxidized for dissolution to occur. The most commonly used oxidants have been sodium chlorate and manganese dioxide. They act indirectly by maintaining iron as the ferric ion which oxidizes uranium by a surface electro- chemical reaction. An Fe3+ concentration of about 1 - 2 g L-I is usually considered adequate for the effective dissolution of uraninite(1)."

Jan 1, 1984

By A Mooney, G Balog, P Burns, R Brooks

This paper outlines the rationale for the location of the crusher, geotechnical analysis and basis of ground support design, design and scheduling of the chamber and supporting excavations as well as the operational outcomes and lessons learned. Contributions from mining operations, planning, geotechnical and infrastructure teams enabled the Crusher Station One excavation to be completed on schedule, with opportunities taken for underground mining and infrastructure to work safely in parallel to deliver crusher station infrastructure on schedule. Installation of crusher infrastructure was ongoing at the time of writing.

Mar 15, 2021

By AIME AIME

THAT the copper industry is in serious straits is admitted. So are the lead and zinc industries, and both lead and zinc are tariff protected. Conditions in the Western lead, zinc and silver mining districts are desperate. These are illustrated by the present disastrously low prices of these metals compared with the levels of two and three years ago and by the comparative rates of metal production and the present activity of the western mining camps. The January production of copper was 32.2 per cent of the 1929 average rate, of steel was 32.3 per cent of the 1929 average, while January production of pig iron was only 27.6 per cent of the monthly average of 1929. The copper industry is only one of many industries that are suffering in this tragic depression. It has been exceedingly prosperous and will be prosperous again when business recovers. Its difficulties are not unique and it does not deserve the tariff equivalent of a dole. The burden of subsidizing through an effective tax or tariff the minority group of high-cost mines would be a heavy one on the consuming public of the United States. On the basis of 1929 consumption figures, an effective 5c. tariff would result in an increased copper bill to the country of over $109,000,000, of which the electric manufacturers would contribute $26,000,000, the telephone and telegraph companies $16,000,000, and the automobile manufacturers $14,000,000. And of this total bill, only $33,000,000 would go to those who are urging a tariff and the balance of $76,000,000 would be paid to those who do not admit either its necessity or usefulness under present conditions.

Jan 1, 1932

By Davide Grassi, Joel Joaquin Cortez, Giovanni Spagnoli, Nick Chittenden

Grouting is a technique used to improve the engineering properties of soils and rocks. Grouting techniques are classified under different criteria: injection method used, type of grout material injected, typical application, and the sequence of construction. The best-known criterion is the mode of entrance or admission of grout into the soil or rock. It is possible to identify therefore several grouting techniques: compaction, fracture, jet/mixing and permeation. The function of penetration grouting is to reduce the permeability of the soil or rock and/or increase the strength and density. In order to avoid displacement, permeation grouting shall be carried out at carefully controlled pressures and flow rates, using appropriate grouts. Colloidal silica is an innovative binder which has low viscosity (about 5 m·Pas), it is not toxic (pH lower than 9) and it is workable between +5°C and +45°C. This paper presents several case histories: a consolidation job related to the installation of a new sewer in North Italy in cohesionless soils, water stopping injection in a weathered granitic bedrock in California, permeation works in the US in sandy soils to improve excavation and the installation of sheet piles in the UAE. Results show that the colloidal silica an innovative and robust technology to perform grouting in very fine soils where conventional binders or micro-fine cements cannot penetrate.

May 1, 2022

By Gustavo E. Armijo

This job was done in Morristown, NJ, with mono fluid system jet grouting for the construction of a new bank building. After the demolition of the existing two story structures, an excavation in loose sandy fill materials was necessary in order to reach the new structure basement level. Due to this jet grouting was selected as a medium to provide both excavation support and permanent underpinning, minimizing the adjacent building settlements. These two adjacent buildings were partially underpinned with a "gravity wall" made with 2 and 3 rows of secant vertical and inclined jet grout columns. Besides the classical jet grouting control methods, during the jet grouting execution, all the drilling and grouting parameters were recorded by a proprietary system called "Slogger". Additionally, after the jet grouting execution, an innovative result control technique was used by means of the application of the same parameter recording system. Some of the production columns were re-drilled and a comparison was made between the obtained drilling parameters and those obtained for the same age test columns. Under the referred existing conditions and in comparison with the conventional underpinning techniques, this project demonstrated that jet grouting, with proper execution and result control, can be faster than them and can maintain the building structural stability and act, at the same time, as a retention system minimizing the existing building settlements.

Jan 1, 2002

By Mario Aiezza

This paper outlines the results of a relationship developed during the design and construction of the foundations for the Gallery Towers project in Melbourne. Both the builder and the piling contractor were determined to arrive at a satisfactory foundation solution to the problems encountered at the site. The scope of piling work was to provide load-bearing piles under the building columns, some of which were located within a retention system that also required a piling solution. Geological conditions were variable and challenging. The site area was small and located adjacent to the National Arts Centre in the developed Southbank area, a high density office area. This presented logistical problems in limiting construction traffic on site and also demanding minimal noise and vibration emanating from piling activities. The piling contractor, Vibro-Pile, and the builder, Walter Construction Group, faced the challenges presented with a refreshing cooperative attitude that was beneficial to both companies. Commercial issues rising from design and construction problems were first put apart in order to allow the respective technical department of each company to work with minimum constraints to achieve the most cost effective solution. In the process usual adversarial attitudes resulting in loss of time and money was avoided. A number of issues were addressed successfully at minimum cost and time during this contract. Despite the difficulties encountered, the job was completed on time and with negligible claims for extras, resulting in the development of a strong mutual respect between both companies.

Jan 1, 2002

By John J. Reed

The mines of southeast Missouri's Lead Belt have been in operation since 1864, almost 100 years. During this period about 10 pct of the total ore available has been left in place as pillars, and this now represents the best ore reserve left to the older mines. St. Joseph Lead Co. has been investigating various plans of pillar recovery for several years. The example to be described is only one possible approach under a specific set of conditions. Conditions vary greatly in the different areas within the Lead Belt, and the same approach would be entirely in- adequate in certain other areas, but there are important sections where this system is clearly applicable.

Jan 7, 1959

By L. A. Pursell

Environmental constraints can both delay and raise the cost of a major plant addition, often requiring a complete reevaluation of the plant site and the proposed project. In this case history, steps are presented which were followed in applying for environmental permits for a major addition to a lime plant. Methods are described for determining expected emission increases and for selecting the best control technology for each source. The description progresses through pre-application conferences with control agencies, the formal application procedure, computer modeling the air quality impact, and the methods followed in obtaining a favorable determination.

Jan 1, 1983

By H. F. Naldrett

"AbstractAt the end of May, 1950, Imperial Oil, Limited, had completed a total of 192 D-3 wells in the Leduc-Woodbend field, 62 of which lost circulation in the D-3 zone for periods ranging from two hours to fifty days. The majority of the remaining wells •lost some mud without actual loss of returns. In addition, independent operators completed 69 D-3 wells, of which 9 lost circulation. Included among the latter is the now well known Atlantic No. 3 well, which blew wild out of control for seven months. The well was finally brought under control through two directionally drilled wells, but not before the derrick fell and the well caught fire. Practically all known filler materials have been used in attempt3 to prevent or regain loss of circulation, but none has been successful, except in minor cases. Ordinary sawdust has come to be the most commonly used filler material and is added to the mud before the D-3 zone is contacted. In cases of serious loss of circulation, the on1y successful method of getting returns has been the use of a series of small cement plugs.IntroductionThe Leduc field is twenty miles southwest of Edmonton, Alberta. Geologically, it is on the east limb of the Alberta syncline, in the homoclinal belt. The main productive zones are in the Upper Devonian formation and are known locally as the D-2 zone and D-3 zone, respectively (see Figure 1).The D-3 zone is a dolomitized reef with fair average porosity and permeability, and shows considerable evidence of vertical fracturing. Porosity is mainly due to moderately uniform development of vugs which are interconnected by small crevices. However, the formation is known to be, locally, extremely vuggy and in places cavernous. These latter conditions create very serious drilling problems due to the hazard of loss of circulation, particularly in the gas cap, which has a maximum thickness of 200 feet. The D-3 zone is contacted at an average depth of 5,300 feet."

Jan 1, 1950

By M. Wasel

The Gross Rosebel gold deposits are located in the Guiana Shield of north central Suriname. Initial discovery of surficial gold in 1880 by local artisanal miners preceded small-scale mechanized mining from 1885 to 1939. The first systematic exploration program was carried out by Placer Development from 1974 to 1977. In May 1992 Golden Star Resources optioned the property. Initial shallow reconnaissance diamond drilling of the extensive surface geochemical anomalies intersected sporadic gold mineralization with no apparent continuity between drill sections. Successive deep augering, trenching and systematic grid drilling based on information from surface mapping allowed development of a preliminary geological model. Further drilling of specific structural-lithologic targets and more complete synthesis of geological data from the trenching and deep auger sampling added to the geological model and defined the multiple controls of gold mineralization. Carefully planned infill drilling on a tighter grid spacing resulted in progressive definition of reserves within six discrete gold deposits. In a complex geological setting, the key to success at Gross Rosebel was persistent, systematic exploration, detailed mapping, careful core logging and perceptive geological interpretation. Reserves now stand at 48.6 Mt at 1.6 glt Au, or 2.4 million ounces of gold. The purpose of this paper is to describe the progression of exploration activity that led to the definition of substantial gold reserves and to summarize the geology of the deposits.

Jan 1, 1998

By Nathan W. Iverson, David S. Graham, Paul J. Axtell

"The Highway 53 relocation project in Virginia, Minnesota, involves construction of a very tall bridge across a currently inactive iron ore mine pit. The inactive pit is partially flooded and serves as the community’s drinking water source. The 1,132-ft long new bridge is a three-span, plate girder structure. Two intermediate, approximately 200-ft tall piers are located within the pit.The foundations for the two piers consist of groups of 30-in diameter piles which, despite the contradiction in terms, are essentially very large micropiles. Extremely challenging and highly variable subsurface conditions exist at the site, ranging from uncontrolled iron ore mine waste fill to some of the hardest rock on earth that can also be highly fractured and abrasive. Despite the conditions, large diameter (30-in) micropile foundations up to 175 ft deep were successfully installed using down-the-hole hammer methods and full-length permanent casing under an extremely aggressive construction schedule.Full-scale foundation load testing using the Statnamic rapid loading method was also conducted in support of the design and construction but under a separate pre-design phase contract. This paper describes the unique aspects of this foundation project, including design, construction, and load testing of the large micropiles.INTRODUCTION AND BACKGROUNDIn 1960, a segment of Trunk Highway 53 (TH-53) in Virginia, Minnesota, was built on land owned by iron ore mining interests. As part of the roadway easement agreement, Minnesota Department of Transportation (MnDOT) was to be given notice three years prior to termination of the easement. In 2010, MnDOT received notice that the mining interests wished to access the ore. Through negotiations in 2010, MnDOT and the mining interests agreed to a 2017 date for abandoning the existing section of roadway. During this period, MnDOT needed to procure project funding, satisfy environmental permitting requirements, and acquire new right-of-way to permanently reroute TH-53 and keep it open to traffic. This was no easy task due to the existing mine pits surrounding the area.The E-2 alignment option shown in Fig. 1 was ultimately selected for the rerouted highway in 2014. The new highway segment includes a three-span bridge across the currently inactive Rouchleau Mine Pit. The inactive pit is partially flooded and serves as Virginia’s drinking water source. The 1,132- ft long new bridge is a three-span, plate girder bridge. Two intermediate approximately 200-ft tall piers are located within the pit. Fig. 2 is a conceptual rendering of the bridge."

Jan 1, 2017

By Lee R. Buhagiar

As a result of the increased seismic risk and the highly variable geology of Christchurch, finding costeffective foundation solutions has been a challenge for the Canterbury rebuild. The soil profile in Christchurch comprises both terrestrial (Springston Formation) and marine (Christchurch Formation) alluvial deposits with a high groundwater table. The result is a highly variable and interbedded soil profile which is prone to liquefaction and static settlement. Vibro-replacement stone columns are very effective in mitigating liquefaction in clean sand. However, the author’s experience has shown that vibro-replacement stone columns are also effective for treating silty and soft soil layers. Vibroreplacement stone columns can be used to treat these soft soils by increasing the composite soil stiffness and providing a load transfer path to the underlying dense soils. Another challenge encountered in the Canterbury rebuild is the cost of redevelopment of brownfield sites with contaminated fill. The costs of disposing this fill often make projects too expensive. Vibro-replacement stone columns have been used successfully to treat contaminated fill, providing a treated soil profile with uniform performance and reducing the cost of disposing of contaminated fill. This paper looks at several case studies in Christchurch, with highly variable soil profiles, where vibro-replacement stone columns have been used successfully to treat multiple soil layers, from contaminated fill to silty soils and soft and non-liquefiable silt.

Nov 1, 2022

By S J. Loach

F-Series reconciliations are formal comparisons of estimates and measurements of ore quantity and quality made at pre-determined points along the mining value chain. F1 is the ratio of ‘Depleted Grade Control Ore/Depleted Long-term Model Ore’ and validates the models upon which Resource and Reserve statements are based. F2 is the ratio of ‘Produced Tonnes and Grade/Depleted Grade Control Ore (-) Changes in Pre-Crusher Stockpiles’ and validates that the ore tonnes and grade delineated in the pit are being accurately extracted and correctly delivered to the processing plant. These factors provide important corporate assurance for a mining company by providing quantitative feedback on model-predicted tonnes and block grade estimates. Since 2009, BHPs Western Australian Iron Ore F-Series reconciliations have been calculated in a single, centralised sequel-server database. This software routinely collates data regarding mineral resource block model depletions, grade control model depletions, pre-crusher stockpile inventories and production tonnes and grade measurements and then calculates F-Series factors for both tonnes and product quality. This paper will present case studies where reconciliation factors were used to identify improvement opportunities leading to projects that improved our models and subsequent forecasts of production tonnes and quality. In addition, it will show how reconciliation factors are tools that monitor control during periods of rapid change and provide feedback on the effectiveness of improvement projects.

Sep 18, 2023

By N. B. Prenn

Case Studies in Open Pit Design Using Whittle 4D will be discussing the following four examples: 1) Optimization of process plant design using Whittle 4D as a sizing tool. In this case, the home office and project team had different views of the size of the final project. The home office wanted to reduce the size of the project to reduce capital expenditure, while the project team suggested a larger project. Whittle 4D was used to determine Net Present Value and Internal Rate of Return using the Whittle scheduler (FDAN) to schedule many alternatives, and calculate the NPV and return for each alternative. 2) Comparison of pit optimization methods: Lerchs-Grossman vs floating cone. Many pits are developed based on floating cone economics. A comparison of methods in one large gold mine resulted in the stripping ratio of the pit being reduced by 10% in the Whittle 4D optimization as compared to the floating cone optimization. 3) Pit optimization to determine if a new mill is justified. A large heap leach gold and silver mine needed to determine if a new mill was justified. The planning and scheduling would take several man months if completed without pit optimization and scheduling software. Whittle 4D software proved to be very effective in providing optimized pits and a mine schedule in a short time frame. 4) Pit optimization to determine how to mine and size. Open pit optimization determined where the underground operation should start, and whether the material should be processed by milling or heap leaching. One of our clients asked for help in determining where the pit should end and a new underground operation start. We used Whittle 4D to help determine where the pit should end and where to go underground. In addition the operation needed to determine how to process the material.

Jan 1, 1996

By A. J. Lynch, L. Ergun, M. Oner

"A research program on modelling cement grinding circuits has been in operation at Hacettepe University, Ankara, for four years. It has concentrated so far on tube mill and air separator grinding circuits for cement clinker, with emphasis on plant sampling surveys, including axial sampling inside the tube mills. The data used for model development have come from 33 surveys in 9 plants.The operating conditions have been:- mill sizes - 3.2 to 4.8 metres diameter and 8.5 to 15 metres long,- mill feed rates - 46 to 158 tonnes per hour,- air flow through mills - 25000 to 125000 cubic metres per hour,- cement clinker work indexes - 10.3 to 18,- separator sizes - 2. to 3.1 metres diameter,- separator feed rates - 132 to 689 tonnes per hour,- separator speeds - 12.3 to 21 metres per second.The ball mill model is Whiten’s perfect mixing model and the separator model is the Tromp curve with a fish-hook. This paper emphasises the importance of calculating the breakage rates and the discharge functions with three case studies at five different circuits which were selected for discussion because they show how particular features of circuit operation can be included in the general models. Size distribution graphs are used to illustrate every aspect of the discussion"

Jan 1, 2003

By S. Burks

This paper develops the themes explained at the previous SAIMM Platinum conference by Whittle and Burks1. Optimization techniques can be used to significantly increase the value of mining businesses by enabling better long- term planning decisions. Open pit and underground mine design, mine scheduling, cut-off grade and blending, stockpiling, and the linking of these to flexible elements of the metallurgical recovery processes are all evaluated together. Transport or sale of intermediate products and the requirements of the product metal markets can also be considered. Experience shows that net present value (NPV) can potentially be increased by 5-35 per cent or more, usually even before the expenditure of significant amounts of project capital. The case studies presented include: ? An existing operation with multiple open pits and PGM concentrators linked to offsite downstream processing facilities, and with infrastructure constraints for which the scheduling of current operations and the potential for expansion were investigated ? An existing operation with an integrated portfolio of mines, concentrators, smelter and refinery, for which the various possible sources of ore for processing were prioritized to match the downstream process plant constraints and the product markets ? An underground operation in Zimbabwe for which the optimum mining width was calculated and expansion plans were evaluated ? An underground mine with many separate mining sections, for which a revised schedule was developed aiming to keep the shaft system and processing plant at capacity with the highest net value material available at any time throughout the life of mine. In the concluding section of the paper, a few brief notes are included suggesting how the strategic recommendations from enterprise optimization studies may be implemented by the Owner?s team.

Jan 1, 2012