Search Documents

By Alessandro Blasi, Massimo Morgana, Corradino Sposato, Pietro Garzone, Giuseppe Devincenzis

A comparison among (2-ethylhexyl)-mono (2-ethylhexyl) ester Phosphonic acid (P507), Secondary-octyl phenoxy acetic acid (CA-12) and Bis(2,4,4-trimethylpentyl) phosphinic acid (Cyanex272), in heavy rare earths separation via hydrometallurgical processes has been investigated. The separation coefficients, , were obtained and the extraction selectivity has been evaluated using a mixture of heavy rare earths from Samarium to Ytterbium. The experimental results indicated that P507 and Cyanex 272 display a greater affinity for heavier rare earths while CA12 proved to be more effective for the lighter rare earth metals.

Jan 1, 2014

By Jason Saldanha, Andrew Evans, Jonathan Baber

"INTRODUCTION The need for a new road crossing at Silvertown is the result of three key drivers:- •,Severe congestion and delay at the Blackwall Tunnel and surrounding road network; •,A lack of network resilience and reliability resulting from a lack of alternative road crossings in east London and the impacts of unplanned closures; and •,The need to support substantial economic development in east and south-east London (jobs and homes) These drivers directly informed the main objectives for a road-based river-crossing solution. The traffic-related problems at Blackwall Tunnel are long-standing and before Transport for London (TfL) assumed control for the strategic road network in London in 2000 the Department for Transport (formerly Dept of Transport) had investigated various relief options including a third tunnel bore and new bridge. This resulted in a new crossing alignment being safeguarded (by direction of the Secretary of State for Transport) and this was refreshed in 2001 in favor of TfL. In recent years (since 2009) TfL as part of the East London River Crossings Programme has undertaken detailed optioneering and feasibility work to address the above ‘need’. This led to the conclusion that a new road tunnel would offer the best solution in preference to bridge, ferry or demand management options. In 2012, in response to a formal request by the Mayor of London, the Secretary of State for Transport confirmed a new road crossing at Silvertown as a Nationally Significant Infrastructure Project (NSIP) by Section 35 direction under the Planning Act 2008. This NSIP designation meant that TfL as scheme promoter must comply with the National Rail and Road Networks National Policy Statement (NNNPS) and must seek the necessary powers to build and operate the crossing by means of a Development Consent Order (DCO) under the Planning Act 2008."

Jan 1, 2016

By Ehsan Alavi, Brian Hagan, Colin LaVassar, Glen Frank, Derek Dugan, Rick Capka, Lisa Mori

"Tunnel face instability is one of the most common issues in EPB tunneling. The evaluation of an ideal face support pressure is a critical element in the design and construction phases of EPB tunneling. In this study, measured tunnel face pressures in three EPB tunneling projects (University Link U230 and U220 projects and the Northgate Link Extension N125 Project) for Sound Transit in Seattle, WA are compared with the calculated analytical methods. This comparison shows that the analytical methods generally overestimate the required tunnel face support. The best practice for managing the face pressure in EPB tunneling operation is discussed based on the experience gained through these projects. Furthermore, the algorithm that is developed for identifying ground loss in these projects is addressed. INTRODUCTION Earth pressure balanced tunneling relies on using muck within the chamber to support the face. Muck is pressurized by controlling the advance rate of the tunnel boring machine and the speed of the screw conveyor. Target face pressure is typically calculated by using the geotechnical assumptions in the geotechnical baseline report. The concept behind EPB tunneling is that the application of sufficient face support pressure will prevent tunnel face instability and the resultant over excavation. Tunnel face instabilities caused by a lack of sufficient face support can lead to ground loss and surface settlement (Anagnostou & Kovári 1996, Kirsch 2010). A certain support pressure must be achieved to counteract water and earth pressure with an adequate factor of safety. While the water pressure can be predicted accurately, the determination of the resultant earth pressure on the face is less precise. This becomes manifested in the relatively high partial safety factors on the earth pressure."

Jan 1, 2016

By Felipe P. D. Lopes, Caroline G. de Oliveira, Sergio N. Monteiro, Lucas A. Pontes, Janine F. de Deus

For decades, natural fibers have been studied as an economical and environmentally viable alternative to use instead of some types of synthetic fibers, for example fiberglass. To find the best way to make composites, the investigations shall be under various configurations, which is extremely important to understand the potentialities and facilities. To aim the comparison of impact performance of epoxy matrix composites reinforced with ramie fabric, the composites were produced by two different methodologies: under pressure and vacuum. The results show that the composites produced under pressure have greater resistance to both the Charpy and Izod Impact than under vacuum conditions.

Mar 1, 2018

By A Melkumyan, K Silversides

The banded iron formation-hosted iron ore deposits located in the Hamersley Ranges of Western Australia contain marker shales that are used to distinguish lithology for geological and orebody mapping. These marker shales produce distinctive signatures in the natural gamma downhole logs, which are conventionally manually interpreted. This paper proposes an alternative method of automatically identifying these shales using dynamic time warping (DTW). A Gaussian processes (GPs)-based method for automatic identification is also considered. Both methods are tested on a deposit that contains the Marra Mamba sequence of the Hamersley Province.Both methods were trained to predict the location of the desired shales, and the resulting outputs were compared with a manual interpretation of the results to determine the accuracy. The GP method can identify signatures with an accuracy between 87.0 per cent and 92.0 per cent, which increases to 92.9 per cent and 95.7 per cent where the GP is certain. The DTW method has an accuracy between 90.0 per cent and 91.6 per cent, which increases to 94.0 per cent and 95.4 per cent where the DTW is certain.The GP method has several advantages, including a more automated library building process, a probabilistic output and a shorter run time. However, the DTW method was capable of accepting more distortion in the signature and therefore identified more signatures. This is important in a deposit where the signals are frequently distorted by events such as hydration and folding. Both methods provide a viable alternative to the current manual detection, but their differences make them applicable to different cases.CITATION:Silversides, K and Melkumyan, A, 2014. Comparison between Gaussian processes and dynamic time warping for classification of marker shales in iron ore deposits, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 177–184 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By Eleanor Kentish, Nathan Bond, Edward Batty, Simon Webber, Alan Skarda

"Crossrail is Europe’s largest construction project — a new 100km rail route running through central London. A joint venture of BAM, Ferrovial and Kier (BFK) has constructed the tunnels and escalator shafts at the new Bond Street and Farringdon Stations. The recent trend in the UK industry towards sprayed secondary linings is driven by the potential for significant savings in cost and time. BFK is unique within Crossrail by constructing both sprayed and cast secondary linings. This paper presents a direct comparison between sprayed and traditional cast in situ secondary linings at Bond Street and Farringdon Crossrail Stations. An objective comparison is drawn between procurement and mobilisation periods, production rates, flexibility, tolerances and logistics in the tunnels. The technical challenges surrounding cast and sprayed secondary linings are explored, and recommendations are made of how each method could be improved for future use. INTRODUCTION It is well established that sprayed concrete offers a fast and effective method to seal the face of an excavation. In a relatively short space of time, sprayed concrete can be applied to an open face to support the short term ground loading on the tunnels during construction. Advances in sprayed concrete lining (SCL) technology — such as the use of wet mix processes, improved accelerators, fiber reinforcement, remotely controlled spraying robots, innovative surveying equipment and nozzleman competency schemes — have greatly increased the speed and safety of tunnel excavations using this technique. As a result, design engineers have become increasingly confident to use SCL primary linings as part of the permanent structural lining (Su 2014). Historically, long term ground and water pressure loads have been considered to be carried by the main structural or secondary lining, constructed using cast in situ concrete (Pickett 2014). However, the advances described above have made sprayed secondary linings a viable option, which has already been proven on the A3 Hindhead Tunnel (Arnold 2012). Sprayed concrete secondary linings offer potentially significant savings in cost and time during the construction process. The contractor does not need to procure a bespoke formwork system for each different sized tunnel — the SCL plant required is already on site for the primary lining. Each bay is sprayed with accelerated concrete, becoming self-supporting almost immediately — compared to moving and resetting the shutter, pumping concrete and waiting for it to cure. With sprayed concrete, working sequences and cross sections can easily be changed."

Jan 1, 2016

By M. Le Roux, Q. P. Campbell, M. Fofana

The determination of densimetric information to predict coal washabilities is an important step in characterising the feed material, as well as the performance of operating plants. However, traditional methods like float-and-sink analysis are hazardous and time-consuming. This is especially true for finer particle size ranges, where very long settling times are required in a medium. De Beers Technologies recently developed a density analyser, known as the RhoVol, for use on diamondiferous kimberlite. Operating over size ranges from 25 mm down to 3 mm, it can determine the mass, volume, density, size and shape of all the particles in a given population and is thus able to provide information about the densimetric distribution on a single particle basis. A study was carried out to compare uncalibrated and calibrated RhoVol results to densimetric and size data obtained using traditional zinc chloride float-sink procedures, for three different coal samples in the size range 3 mm to 8 mm. The results indicate that the RhoVol can be used to provide simple, rapid and safe size-by-washability information for coal, provided proper pre-calibration is done, mainly to account for the effects of particle porosity in the density determination. Keywords: Coal washability determination, RhoVol, densimetric curve

Jan 1, 2020

By H. J. McQueen

The modeling of the extrusion of 6061 alloy and its composites with 10 to 20 vol% Al203 or SiC by two techniques. The uniaxial finite element method FEM (DEFORM" ) provided force-stroke curves and temperature rise over the range 450-500 °C, 2.6-5mm/s and extrusion ratios of 31 and 64. The traditional technique considers ideal work and redundant work as well as friction and uses average temperatures and strain rates. The two techniques are used to clarify each other and to extend the analysis to 400 and 350 °C. The calculated efficiencies are compared to measured values in extrusion trials and to values derived for 7075 extrusion analyses. The analyses are based on constitutive equations determined by torsion testing tests.

Jan 1, 2004

By Albert Ladd Colby

A GLANCE through the Bibliography appended to this paper will show that the Transactions of this Institute contain what virtually contitutes a history of the development of the manu¬facture of steel rails in this country and abroad. It is, therefore, fitting that this paper, bringing one branch of this important subject down to date, should be here presented, and it is also appropriate to select this joint meeting of our Society with the Iron and Steel Institute to compare the specifications covering the rails produced in these two countries, and to propose a standard specification to govern the manufacture of American rails for export. During the last ten years the production of Bessemer steel rails in the United States and Great Britain has amounted to 32,128,720 gross tons. Nearly 19,000,000 tons have been rolled in the past five years. The next five years will see an even larger output, owing partly to the extension of railway projects in the Orient, in South and Central America, in Mexico, and in Australia and the other British Colonies. Of late years, the American rail-mills have so largely increased their daily output, that trade conditions have often made possible the delivery of American rails to foreign ports. The tenders submitted by American mills, however, have always been accompanied by requests for changes in the foreign specifications, chiefly in the reduction of the amount of testing required; and it has only been natural, especially at first, that the engineer, whose specification had always been accepted without question by British mills, should interpret American tenders 'as an evidence that an inferior rail would be furnished

Sep 1, 1906

By M. Saghaeian, R. Hejazi, H. Abedini

Vertical ring and Pulsating Wet High Intensity Magnetic Separator (VP-WHIMS) is widely used for week magnetic mineral beneficiation or ferrous impurity removal from non-metallic minerals. Because of the complexity of this machine, mathematical modelling of its process is complicated and time consuming. In this paper, artificial neural network (ANN) and response surface methodology (RSM) were applied to evaluate the VP-WHIMS performance and optimize its main operating parameters in beneficiating of the Chadormalu hematite sample. The operational parameters of this magnetic separator are considered as: magnetic field intensity (2500-8500 gauss), pulsating frequency (20-100 %max), ring rotation speed (0.6-4.6 r/min) and slurry concentration (15-35 w/w %). Concentrate grade and recoveries (weight and Fe) are monitored as responses. Centre composite design (CCD) was used for experimental study. Four process variables were set using small CCD. Eight star points (a=±1), eight axial points (a=±2) and five replicates at the centre point (a=0) were chosen as experimental points. In ANN system, the best network topology was obtained as (4-5-3). The weights connection and biases were obtained using batch back propagation (BBP) method for 21 experimental data points. The results indicate that ANN

Jan 1, 2014

By J. D. Davis

The Bureau of Mines Coal Carbonization Laboratory has been interested for the past 20 years in the quality of coke in connection with the selection of coals for the manufacture of coke. The principal experimental. method of carbonization, whereby 100- to 200-pound charges are carbonized in sheet-steel cylindrical retorts with recovery and determination of the properties of coke, gas, and products, was developed in cooperation with the American Gas Association,4 5 and it is known as the BM-AGA method. Results of the investigations of 90 coals included in the BM-AGA Survey of the Carbonizing Prop¬erties of American Coals have been published; 6 and, in addition to these, about 200 coals have been carbonized over limited temperature ranges. Because coke from cylindrical retorts differs in shape from that made in rectangular ovens, the BM-AGA method has been criticized, although those who developed it have always believed that it served well as a means of measuring the relative strengths of cokes from different coals. It is recognized that no laboratory-method carbonization, even on a large twit, can yield results that exactly duplicate those obtained in commercial ovens and retorts. However, with the completion and satisfactory performance of an experimental vertical slot oven of 500-pound capacity at the University of Illinois Geological Survey Laboratory,' the opportunity to directly compare BM-AGA coke with coke made by two-sided heating became available and the necessary test apparatus was installed. The Bureau of Mines slot oven, which is similar to that designed by the University of Illinois Geological Survey, has been used to carbonize 11 coals (or blends) tested by the BM-AGA method. This report compares the results obtained by the two methods.

Jan 1, 1950

By T. J. Lutz, S. Gallagher, J. R. Srednicki, J. J. Sammarco

The Illuminating Engineering Society of North America reports that an underground mine is the most difficult environment to illuminate (Rea, 2000). Researchers at the U.S. National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) are conducting ongoing studies designed to explore different lighting technologies for improving mine safety. Underground miners use different visual cues to escape from a smoke-filled environment. Primary and secondary escapeways are marked with reflective ceiling tags of various colors. Miners also look for mine rail tracks. The main objective of this paper is to compare different lighting types and ceiling tag colors to differentiate what works best in a smoke-filled environment. Various cap lamps (LED and incandescent) and lasers (red, blue, green) were compared to see which options resulted in the longest detection distances for red, green and blue reflective markers and a section of mine rail track. All targets advanced toward the human subject inside of a smoke-filled room to simulate the subject walking in a mine environment. Detection distances were recorded and analyzed to find the best cap lamp, laser color and target color in a smoke environment. Results show that cap lamp, laser color and target color do make a difference in detection distances and are perceived differently based on subject age. Cap lamps were superior to lasers in all circumstances of ceiling tag detection, with the exception of the green laser. The incandescent cap lamp worked best in the simulated smoke compared to the LED cap lamps. The green laser was the best color for detecting the tags and track compared to the red and blue lasers. The green tags were the easiest color to detect on the ceiling. On average, the track was easier for the subjects to detect than the ceiling tags.

Jan 1, 2013

By W. Hermülheim, J. Brune

"This paper analyzes mine emergency management and rescue practices in German underground coal mines and compares them to those used in the United States. The German mining industry has developed these practices over more than 100 years, and they have successfully managed numerous fire, water inundation and ground control emergencies using these techniques. The authors interviewed German mine emergency professionals about rescue team and emergency operations. These operations were then analyzed to determine which of these German principles would be of interest to United States mine rescue teams. Implementing these programs into United States mine rescue and emergency operations was analyzed. INTRODUCTION Coal mining has become much safer industry than it has been in the past. Advances in safety and health regulations and company polices have improved working conditions for miners all over the world. Even with these advances there is still a need for continued attention to safety and health. It is also important for mine safety professionals to observe practices and procedures in other countries and cultures and learn what and how to apply this knowledge in their own systems. Coal mine rescue has been an integral part in improving coal mine safety. Mine rescue procedures have evolved with time, experience and technology development. Today, coal mine rescue teams are still needed and must be continually trained and prepared for any mine emergency. Although it is hoped that improved mine safety policies and practices will eliminate coal mine disasters in the future, accidents remind us that disasters can still happen today. In May 2014, Turkey experienced a severe coal mine disaster where 301 people were killed [G.Tuysuz, 2014]. Our industry must learn from these incidents, focusing on disaster prevention and making improvements in mine rescue operations. Mine rescue procedures differ from country to country due different regulatory environments and different historical evolution of emergency response. Sharing practices and procedures from one country to another enables learning from different experiences and cultural backgrounds. Sharing is also a way of preserving information, identifying and learning best practices."

Jan 1, 2015

By C. Aimone-Martin, C. Dowding, M. Jern, J. Gjødvad

This article compares percentages of compliance for six national standards to demonstrate how these standards vary on-site in a real project. This, to the best of the authors' knowledge, has not been accomplished before. Different standards not only vary in allowable amplitudes of induced vibrations but also in how they are measured (transducer location, transducer orientation, frequency content of vibration, etc.). Thus it is not straightforward to compare the permissible values of induced vibrations with each other. This challenge of comparison is overcome in this project by instrumenting a structure with multiple transducers according to different national standards and comparing the degrees of compliance. Compared herein are compliance with standards used in United States of America, Germany, Great Britain, France, Austria, and Sweden. Averages of the percentage of compliance and ratios of measured vibration amplitudes for all six national standards are compared both in tabular and graphical form for 20 blasts at the Aitik mine northern Sweden. It is the largest open pit mine in Europe and blasts are atypically large with more than 1000 kg charge per hole and several hundred holes per blast, lasting 3-5 seconds. Results show that percentages of compliance can vary by as much as 2 to 75 % for these blasts at this structure. The overall project is a cooperative effort between EFEE (European Federation of Explosives Engineers) and ISEE (International Society of Explosives Engineers), supported by more than 17 persons from 8 different countries. At the present the experts are the four authors of the present paper and Dr. Robert Farenfield, Dr. Nathan Rouse, Douglas Rudenko, Brent Meins, Kenneth K. Eltschlager, Karin NorénCosgriff, Travis A. Davidsavor, Vitor Luconi Rosenhaim, Johannes Kutschera, Bernard Thierry, Thomas Moser, Cory Loukedis, and Keith Best. The project began with a literature study and a survey including an evaluation of the answers provided by members of EFEE. Results were presented at the ISEE conference in Denver 2020 as well as the EFEE conference in Helsinki in 2019 (Gjødvad & Jern, 2019; 2020). The second part of the project was initiated in May 2021 with installation of 7 seismographs from two different manufactures, 3 cracs gauges and 2 microphones on a building at the Aitik mine in northern Sweden. The third part of the project has moved to the United States. Two residential structures adjacent to quarries are being monitored in Michigan and Ohio. Installation and monitoring began in March 2023 and are expected to continue for 6 to 12 months. In addition to the objectives of phase two the 2023 study includes calculations of global wall strains from measured velocity time histories and measurement of response of existing cracks to vibratory and climatological effects

Jan 1, 2024

By N. Naude, L. S. Leal Filho, M. P. Tshazi

In this paper, the authors performed experiments in the Denver and Leeds laboratory flotation devices at the University of Pretoria at various particle sizes to evaluate the performance of the devices. Quartz was used in a single mineral system at discrete sizes fractions, -25 μm, +25- 45 μm, +45-75 μm, and +75-106 μm. Hydrodynamic analysis, based on dimensionless power and Reynolds numbers, indicated that the Leeds cell required higher power input to achieve comparable flow conditions. Specifically, the Leeds cell exhibited an average power number of 1.03, whereas the Denver cell averaged 0.77 within the same impeller speed range of 1000 rpm–1500 rpm. For comparative flotation performance, impeller speeds were calibrated, resulting in operating speeds of 1200 rpm for the Denver cell and 1400 rpm for the Leeds cell. The cells performed similarly at two coarser-sized fractions. However, some deviations were observed in the finer particle size range. The -25 μm (fine) fraction initially achieved a recovery of only 15%. An additional reagent dosage was required to enhance the recovery of this fraction significantly. These findings highlighted the influence of particle size on flotation recovery. For all experiments, the Denver laboratory flotation cell outperformed (defined by higher recovery) the Leeds device, while still operating at a lower impeller speed. This advantage can be attributed to its impeller-stator design and air dispersion features, effectively overcoming slurry resistance and resulting in superior flotation performance compared to the Leeds cell.

May 27, 2025

By Ernest Y. Baafi

This paper describes the results of a series of comparative studies in which polygonal, IDS, and kriging were compared for their local estimation accuracy. The specific objective of this study was to determine the impact that the particular nature of the mineralization has on the results of such comparative studies. The study was performed on simulated coal deposits and the evaluation parameter chosen was the coal thickness. For this study, many conditionally simulated deposits having different degrees of seam thickness continuity were first developed. Each simulated deposit covered an area of 30,000 ft x 30,000 ft which was, in turn, subdivided into 100 mine planning blocks of 3,000 ft x 3,000 ft in size. Thickness estimation was made for these mine planning blocks using surrounding DDH assays. In all cases tested, e.g., from a perfect continuity to a complete lack of continuity in coal seam thickness, kriging gave the best estimates among the three, followed by IDS and polygonal methods. As expected, the relative efficiency (i.e., superiority) of kriging over other estimators was highly dependent on the nature of mineralization.

Jan 1, 1982

By B. S. Ignasiak, B. N. Nandi, D. S. Montgomery

The growing need to measure the extent of weathering of coking coal in storage and in transit prompted the comparison of the dilatation of coking coal on heating, which is known to be a sensitive index of oxidation, with the composition and volume of the gases produced by a mild pyrolysis of the same coal. It was found that the pyrolysis method had the advantage in that it could be used to study coking coals in advanced stages of oxidation, when the swelling properties had been largely destroyed. Of the various constituents in the pyrolysis gas, the most sensitive indication of coal oxidation was the volume of carbon monoxide evolved per gram of coal. For the coals examined, this index appeared to be at its best when the temperature of pyrolysis was approximately 35oC.

Jan 1, 1970

By M. J. Collins, L. C. Trytten, K. R. Buban, I. M. Masters

Both pressure leaching of zinc concentrate, in an autoclave, and atmospheric leaching, in stirred tanks, have been employed in the expansion of zinc production at plants employing roast-leach-electrowin technology. These direct leaching methods result in the conversion of the sulphur in the feed to the elemental form, rather than to sulphur dioxide, decoupling zinc production from acid production. Atmospheric and pressure leaching methods are also readily implemented over a wide range of production rates. In choosing the best technology for expansion, capital and operating costs, zinc recovery, byproduct quality and the compatibility of recycle streams with the existing refinery must be compared. Leach testwork with several zinc concentrates using both methods has been performed by Dynatec. Recent results are presented, along with a discussion of their implications for process selection.

Jan 1, 2000

By Harpal Parmar

This paper evaluates dynamic methods of pile capacity prediction by comparing their results to static load test results. Dynamic and static pile load test data were assembled from four southeastern states of the U.S. End-of-drive and restrike capacities were evaluated using the Pile Driving Analyzer (PDA) and by wave equation (WEAP) analyses. These were compared to static (Davisson criterion) loads. The best comparison was obtained for restrike PDA results; restrike wave equation analyses values also compared well. The end-of-drive results for both methods-showed relatively poor comparisons. The PDA was recognized as an important tool to measure energy transferred to the pile; this transferred energy was recognized as an uncertainty when conducting wave equation analyses. A statistical analysis showed restrike capacity results to be associated with higher precision and accuracy as compared to end-of-drive methods. The authors believe that restrike dynamic testing is essential to establish long term static soil strength and that it will lead to accurate and cost-effective design of piles.

Jan 1, 1996

By M Jahani, M Taji

For suitable production planning in an open pit mine, and also to carry out the optimisation process during the mining production cycle, prediction of fragment size distribution is required prior to carrying out the blasting operation. For this purpose, many prediction models, such as empirical models, were presented. The proficiency of these models differs in various conditions and mines. Therefore, in this paper the most important models, including SveDeFo, Kuz-Ram, CZM, Modified Kuz-Ram in 2005, Kuznestsov-Cunningham-Ouchterlony (KCO) and also Gheibie et al, were examined by the information of 20 blasts in Gol-Gohar iron ore mine. Fourteen images were taken on average for each blast. For image processing analysis Split-Desktop software was used. After examination, it was understood that none of the available empirical fragmentation models had presented acceptable performance, except the Kuz-Ram model for magnetite ore, which had somewhat acceptable results. However, this model for blasting patterns in hematite presented unsuitable results. Examination and comparison of two important distribution functions, Rosin-Rammler and Swebrec, were carried out and it was observed that the performance of Swebrec for fines was far better than Rosin-Rammler. This result for the upper part of fragment size distribution curve, coarse, is the reverse.CITATION:Jahani, M and Taji, M, 2015. Comparison of empirical fragmentation models at the Gol-Gohar iron ore mine, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 707–714 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015