Search Documents

By S. J. Stokowski

Abstract An extensive drilling and laboratory testing program indicates that a construction aggregate resource is present within the Oligocene Sombrerito Formation limestone, southwestern Dominican Republic. The first part of the testing program included the collection, photographing and geologic logging of diamond drill cores to allow lithologic subdivision of the strata into potential quarry layers. The primary lithostratigraphic units are: I- (youngest) approximately 10 m of white, dense marine limestone II-approximately 5 m of white, interbedded dense and chalky marine limestone III-more than 2 m of tan, chalky, calcitic dolomite. Unit I is often altered by lateritic weathering and/or dolomitization. Unit II is often altered by dolomitization. The cores were individually crushed by quarry layer into coarse and fine aggregate sizes for chemical and physical analyses: specific gravity and absorption, MgSO4 soundness, sand equivalent, Atterberg limits of the minus #40 mesh fraction, and LA degradation. The unaltered portion of Unit I is suitable for all construction aggregate uses. Unit II is best suited for crushed stone base. Each of the non-weathered units decreases in coarse-aggregate yield and quality with depth and diagenetic dolomitization. Dolomitization typically causes about 5% lower yield of coarse aggregate, a sand equivalent of about 20 units below the original value an increase in absorption of about 3%, an increase in the LA of up to 13%, and a decrease in the average five-cycle MgSO4 soundness of about 17%.

Jan 1, 1991

By Seedsman R. W

Good roads are essential in moving men and materials to and from the underground workplace. Coffey Partners International Pty Ltd (Coffey) has recently completed a underground coal industry funded project on underground mine road construction and maintenance. This paper discusses practical approaches to construction and maintenance of underground mine roads using transferrable civil technologies and innovative techniques. Mine pavements are generally low-cost (relative to civil roads), constructed to varying standards using locally available materials to best meet the mobility needs of the mine. Performance of pavements is thus largely dependent on the environmental conditions, quality of the available road making materials, maintenance policies and available resources. The paper will detail `what causes bad roads?' in various underground environments, available management strategies, construction and water control techniques, road maintenance and vehicle considerations.

Jan 1, 1995

By G. C. Hodgson

Specification and Tests of Rope Wire Chemical Analysis: The range in composition of steel used in the manufacture of wire rope is as follows: Carbon 0 4 to 0.9 per cent Manganese 0 4 to 0.8 Sulphur Not above 0.04 Phosphorus Not above 0.04 The carbon and manganese content are varied according to the gauge of wire to be drawn and the tensile strength required. Generally speaking, best results are obtained from heats where the melt is not of too large a tonnage. The amount of reduction and patenting of the wire is left to the wire maker, who thus has a free hand in meeting the balance of the specification.

Jan 1, 1931

By A. Bruynesteyn

Many papers 'have been publihed on the role of the bacterium.Thiobacillus ferrooxidans in the oxidation of reduced sulfur compounds, and years of research have established the following environmental factors, which influence biological oxidation. 1. Oxygen is required for the oxidation of reduced sulfur compounds to the sulfate form. Sufficient oxygen. is available from the air, consequently, it is of importance to get the air to the bacteria. 2. The bacteria are active in the pH range 1.4 3.5. Maximum activity occurs at pH 2..0 - 2.8. 3. -In order to allow the bacterial populations to expand, certain essential nutrients must be available. Nitrogen has to be supplied for the production of body protein, and ammonia is the source most readily accepted by the bacteria. Carbon dioxide is the only utilizable source of carbon and the small amounts available in air are the primary source of this element. Small amounts of phosphate, manganese,, potassium,. calcium. and magnesium are also required. These trace minerals are available from the water and host rock in sufficient quantities. 4. Water is required as a carrier for the oxygen carbon dioxide and other nutrients, as-well as a solvent for the metallic sulfates produced. The bacteria are motile and the water allows the bacterial populations to spread:: bacterial activity ceases if the equilibrium relative humidity drops below 100%. 5.-optimum bacterial activity occurs at temperatures of 34 - 35°.C (93 -.95° F). All activity ceases above 45° C. At lower temperatures, activity its dramatically decreased, but there is still a significant amount at 10 - 11° C.- Thiobacillus ferruoxidans has been isolated from a mine with a year round temperature of 3° C. 6. Unpublished results from our laboratory show that biological leach ore oxidation takes place during the rest periods at the same rate as during the wet leaching periods providing there is a film of moisture remaining around the particles. Optimum conditions can be readily achieved in the laboratory, but application of our laboratory knowledge to commercial leaching dumps is riot as simple. Attempts to achieve improved environmental conditions for the bacteria in leaching dumps would require substantial capital investment and careful planning of leaching operations. This paper

Jan 1, 1972

By Martin D. Larisch

The construction of diaphragm walls and most large-diameter bored piles (piers) is often carried out under drilling support fluids to temporarily stabilise the excavation prior to concrete placement. In most cases such fluids are either mineral-based slurries (bentonite) or polymer support fluids. The working mechanisms of these two fluid types are fundamentally different. Designers need to consider possible fluid-related impacts on the permanent design performance of the project-specific deep foundations as well as for the temporary excavation stage during construction. Robust design methods for bentonite slurry-supported excavations have been developed in the last few decades and the working principles and associated risks of such mineral-based slurries are understood reasonably well. However, such meth-ods have not been developed in detail for polymer-based drilling fluids. This document provides a brief overview of the main characteristics of bentonite- and polymer-based drilling fluids as a guide for construction practitioners and design engineers alike. The paper also high-lights some common construction risks related to casing installation and the selection of suitable fluid systems for different ground conditions. Typical defects caused by the incorrect application of drilling support fluids, and their pro-active mitigation, are discussed, too. In addition, the basic concepts of sta-bility calculations for bentonite fluid-supported deep excavations are briefly introduced and their ap-plicability for other fluid types such as polymer-based support fluids or water are reviewed.

Nov 1, 2022

By Jim Slatter, Ben Collingwood

"It is well known that the adoption of an appropriate construction methodology is critical to quality outcomes for bored piles (drilled shafts). Many case studies have been published documenting quality issues that have arisen due to a range of causes involving ground conditions, ground support, drilling and cleaning techniques, groundwater, concrete properties and concreting methods, amongst other things. Despite the body of published information, pile defects remain common in practice. The authors share over 40 years’ experience in the Australian piling industry and have participated in many hundreds of projects involving bored piles in design, construction and testing roles. It is the authors’ experience that many defects are caused by conditions or practices that are known to be problematic, but that are often not recognised or addressed at the time of the works. This paper provides an overview of industry practices and key factors relevant to quality outcomes. The authors draw upon their own construction experience, published case studies and guidelines, and observations from independent pile testing activities they have been involved in across the Australian piling industry. The intent of the paper is to provide a consolidated review of typical industry practices and to highlight key areas in which construction quality can be enhanced.INTRODUCTIONThere are many published studies of cases where bored piles have been constructed and found to have concrete defects. The authors have had personal involvement in many cases where the outcomes and learnings are not publically available. The nature and cause of defects is always dependent on site and project specific factors, and therefore methodologies and materials that produce satisfactory outcomes in certain circumstances may be problematic elsewhere. The process of bored pile construction encompasses the following key areas:??excavation and ground support;??pile preparation and cleaning;??pile reinforcement and fitments.??concrete supply and mix performance;??concrete placement methodology;Each of these elements is equally important and can influence construction quality in completed piles. In the authors’ experience, it is often a combination of seemingly minor issues that leads to significant defects in piles. Conversely, attention to detail in all aspects of bored pile construction is required to produce outcomes of a consistently high standard."

Jan 1, 1900

By F. E. ROGERS

CUSHMAN TUNNEL No. 2 is adjacent to the Hood Canal, near potlatch, Wash. It is 17 ft. inside .diameter, about 13,000 ft., or two and one- half, miles in length, and is a part of the second unit of the Cushman power project. It connects Cushman ' Dam No. 2 and the penstocks that lead to the power house on the beach about 400 ft. vertically below the outlet of the tunnel. One shaft, 190 ft. deep, and two adits between 300 and 400 ft. long, were provided to speed up driving operations. his arrangement gave 6 working headings, which were operated 24 hr. daily. The shaft provided a manway, cageway, and skipway.

Jan 1, 1931

A poured slag bottom is universally considered to be the best type bottom for copper reverberatory furnaces. It is impervious to molten matte and ready for immediate use.When molten slag is not available a monolithic silica bottom is the second best; such a bottom has been adopted at Mount Morgan. The laying of such a bottom is a phase of smelter construction on which so little real information is obtainable that a day to day record of such a recent example as Mt. Morgan's 19 ft. x 40 ft. reverberatory may be of interest. The work was done under the direction of E. Pesout, of McGill Smelter, Nevada. PREPARATION OF THE BOTTOMA 26-inch bed of closely packed firebrick with sand-filled joints was first laid on the clean, dry concrete foundation and the whole dried out by small fires maintained on the brickwork for several days. Ninety tons of silica sand was meantime thoroughly dried and stored in clean drums. This sand must be low in FeO and CaO and contain about 95% Si02 , the majority of which should be present as tridymite. This form of silica shows little expansion at high temperatures, for it is the form stable between 870° and 1470° C.Its presence thus minimises disturbance to the bottom by the expansion which, during the burning in, would mark the transformation of quartz to tridymite.

Jan 1, 1939

By Brian Wilson, Megan Atkinson, Richard Diggle, Nathan Sweeney

"Ruskin Dam, located near Mission, British Columbia, was constructed in 1929 and 1930 and comprises of a concrete gravity dam structure founded on bedrock. At the right abutment, which consists mostly of dense to very dense sands and silt, the dam abuts against overburden soils, and connects to a cutoff wall system consisting of sloping concrete slabs. Significant seepage and piping issues were encountered during first filling of the reservoir in 1930. In 2012, BC Hydro, the owner of the dam, awarded a contract for the construction of seepage control measures at the right abutment, including construction of a plastic concrete cut-off wall extending upstream of the dam, a plastic concrete seepage training wall extending downstream of the dam, tie-in of the new cutoff wall to the dam, consisting of jet grouting of the soils adjacent to the dam to allow for the construction of the special cutoff connecting the cutoff wall to the dam, and construction of additional jet-grouting ground improvement downstream of the dam.Integral to the upgrade was the requirement for the special tie-in cutoff wall, consisting of a highly flexible, impermeable membrane to connect the concrete dam to the new, 1 m thick plastic concrete cutoff wall. The tie-in extends vertically into bedrock through the dam and jet grout columns constructed adjacent and beneath the overhanging portion of the dam at the right abutment. The membrane is required to survive the anticipated earthquake induced deformation between the dam and the abutment soils.This paper describes the processes used to develop a material suitable to meet the specified flexibility and permeability criteria, as well as the innovative construction techniques utilized to construct the slot and place the bituminous material within it. The final dimensions of the slot were in the order of 7 m long by 25 m deep by 0.17 m wide. The bituminous material was placed under a head of water which was required to maintain stability of the slot, and was placed at temperatures in excess of 120 degrees Celsius."

Jan 1, 2017

By Mirko Martini, Marcelo Benaglia, Andrea Codalli

Riachuelo Lot 3 forms part of a sanitation programme being implemented in Argentina to relieve the Riachuelo river basin from its current contamination. The programme, by far the most important in its kind in the country during the last decades, will expand the sewage capacity of Buenos Aires and will benefit an area of 4.3 millions inhabitants by intercepting a number of waste water discharges and conveying them to a new treatment plant prior to final discharge into the Rio de la Plata. The project foresees amongst other works the construction of an onshore 48 m deep shaft at the outlet of the treatment plant plus a 4,3 m inner diameter outfall tunnel of 12 km length. The last 1.5 km of the alignment is fitted with 34 vertical risers jacked from inside the tunnel to allow the discharge and dilution of the treated effluent into the Rio de la Plata. This paper describes the peculiarities and challenges, both in terms of design and in terms of construction, of the outfall tunnel, which was entirely bored under the Rio de la Plata using a 5.2 m cut diameter Tunnel Boring Machine (TBM). On one hand, the tunnel segmental lining was designed to work in tension during the system flow rate peaks while on the other the tunnel excavation faced a variety of complex conditions, such as crossing water bearing permeable soft ground formations and advancing at face pressures in excess of 3,5 bars for the entire route.

Jun 13, 2021

By Ehsan Alavi, Eren Kusdogan

The City of Toronto’s Coxwell Bypass Tunnel is currently being constructed by North Tunnel Constructors ULC, a joint venture of Jay Dee Canada, C&M McNally Tunnel Constructors and Michels Canada. This project includes construction of approximately 10.5 km of 6.3 meter finished diameter rock tunnel, five 20 meter diameter storage shafts and eleven tunnel connection drop shafts, along with associated deaeration and adit tunnels. This paper describes progress on the project to date and reviews the risk mitigation measures utilized on the project to move the project forward through tough geological conditions during shaft excavation and tunneling phase of the project.

Jun 13, 2023

By Geoffrey D. Collins

This paper deals with the construction of the Effluent Outfall Diffusers which form part of the outfall for the Deer Island sewage project. The work was executed 15 km out to sea in Massachusetts Bay and required the drilling, installation, grouting and accurate determination of the actual position of 55 riser shafts in 33.5 m deep water. Although not strictly a "foundation", the contractor's approach to the installation of the diffusers was a logical development from many marine foundation projects executed by the Contracting companies over the last decades. The only previous application of this design of outfall had been in Australia where offshore oil drilling techniques had been adapted for use in riser installation.

Jan 1, 1994

By C. R. Stephan

Explosion-resistant seals in underground coal mines isolate the environment within the sealed area from the active workings of the mine. The current United States Title 30 Code of Federal Regulations (CFR) requires these seals to be constructed of solid concrete blocks. The CFR also allows for alternative methods or materials to be used to create a seal if they can withstand a static horizontal pressure of 138 kpa (20 psi), provided the method of installation and the material used is approved in the ventilation plan. The purpose of this report is to identify those explosion-resistant seals that have been tested and meet or exceed all the requirements of the CFR.

Jan 1, 1997

By K. V. Lindell

Introduction This paper describes a recent innovation in the design and construction of mine headframes. A reinforced concrete headframe was built by using sliding forms. A concrete headframe of conventional design was originally considered, but investigation of this project showed that it was doubtful if the bearing strength of the soil was sufficient to support the great weight of a structure of this type. In addition, the slope and the fractured condition of the serpentine bed-rock did not permit satisfactory piling. A conventional steel headframe with storage bins was then designed, but, due to the steel situation, delivery promises were set back many months. The concrete headframe was again investigated, and a design was adopted incorporating a circular headframe lower in height than that first considered, with skips discharging into a smaller surge bin. The upper section of the shaft collar was strengthened to result in a stable structure which would be supported by bed-rock, as well as by the concrete and steel lining of the shaft itself.

Jan 1, 1948

By Dan Brown

Improvements in construction equipment and techniques in recent years have made possible the use of drilled shaft foundations in diameters and lengths not previously considered practical or feasible. Many highway bridge and other structures are now routinely founded on drilled shafts which are 2.5 m to 3.0 m (8 to 12 feet) in diameter and extending over 60 m (200 feet) in depth below grade. There are unique challenges associated with constructing such large and deep cast-in-place foundations and engineers should be aware of the special needs associated with site investigation, construction specifications, material requirements, and quality assurance. This paper outlines a number of special considerations for these foundations, along with strategies that may be employed to improve the reliability and quality of large drilled shaft foundations.

Jan 1, 2008

By Dan Brown

Improvements in construction equipment and techniques in recent years have made possible the use of drilled shaft foundations in diameters and lengths not previously considered practical or feasible. Many highway bridge and other structures are now routinely founded on drilled shafts which -are 8 to 12 feet in diameter and extending over 200 feet in depth below grade. There are unique challenges associated with constructing such large and deep cast-In-place foundations and engineers should be aware of the special needs associated with site investigation, construction specifications, material requirements, and quality assurance. This paper outlines a number of special considerations for these foundations, along with strategies that may be employed to improve the reliability and quality of large drilled shaft foundations.

May 11, 2007

By Rudy Scarabelli, John R. Wagner

At one time explosives were the only economical means of rock tunnel excavation. Except in relatively long tunnels in the right rock explosives are still the cheapest means of rock excavation where they can be used. Today the most economical means of rock tunnel excavation is increasingly not the choice of the contractor. A good part of our work is for public agencies in urban areas and the public today is increasingly less tolerant of the disruption caused by our efforts. Owners in many cases have to direct their engineers to write specifications which severely restrict noise and vibration levels during construction. Sometimes specifications allow drill-and-shoot for starter tunnels only or even eliminate powder by fiat. Recent advances in the use of explosives such as sequential firing have made blasting more palatable to the public but are not enough in all situations. Thus the roadheaders on construction projects. In recent work I have seen the Alpine Miners, a Paurant Miner and the Robbins Mobile Miners used in several rock formations and now believe this type of equipment has a place in the tunnel constructor's choice of equipment. Rudy and I have not attempted to present a formula for choosing the best alternative excavation method in any given case because, of course, of the variables involved. We have simply tried to describe our experiences on a particular project and hope our observations will be of some value to tunnel constructors.

Jan 1, 1987

The principal dirnensions of the chimney were fixed as follows: Height from formation to coping, 328 ft. 8 in.; inside diameter concrete shell, 13 ft. Gin.; inside diameter of the 4~-in. brick lining. 11 ft. (j in. ; shell thickness above flue inlet at a point 39 ft. above formation, 1 ft. 8in.; shell thickness at coping, 6 in. That is, the inside of chimney is cylindrical, wldst the outside is gradually stepped inwards with of 1 in. and less until the shell is 6 in. thick only at the top. With these dimensions in mind, it will be seen that some close thought was necessary to ensure a satisfactory of fonn which could be kept rigid and plumb to a height and at the same time provide safe working conditions for the labourers employed.FOUNDATIONSThe spread base of the chimney is 45 ft. in diameter, and foundations were carried down to a depth of 8 ft. 6 in. below natural surface into good hard clay which was known to be the best foundation obtainable in the vicinity being capable of withstanding, when dry, a load of 3 tons to 4 tons per square foot, whereas dead load is 1A tons per square foot and the maximum load expeeted under the most severe wind condition is 2 tons per square foot to ensure the foundation being kept dry and unaffected by ground water, the site was surrounded by a ring drain at a distance of six feet from edge of concrete foundation and at a minimum depth of one foot below bottom of concrete. Open-jointed pipes were laid in the bottom ofthe drain and graded to a pipe drain with outfall clear of the site.

Jan 1, 1924

By J. A. MacLellan

"CONSTRUCI'ION OF SHERRITT'S CONCENTRATORSSherritt Gordon is operating two mills north of the 56th parallel, and is presently engaged in building a third. The author was closely involved in the design and construction of all three of these concentrators.The Lynn mill is the oldest of these three concentrators-it is a 4,000 ton per day nickel-copper plant built in 1953. The Fox mill is a 3,000 ton per day copper-zinc concentrator built in 1970. The Ruttan mill will be a 10,000 ton per day copper-zinc plant scheduled to go on line in July 1973.LYNN MILL The Lynn mill including the crushing, concentrating, drying and load out plant is about 69,700 square feet or 17.4 square feet per ton per day. '!his plant was originally built in 1927 at Sherridon, 150 miles south of Lynn Lake, as a 2,000 ton per day copper-zinc plant. In 1952 the plant was moved by tractor train to Lynn Lake. The whole plant was re-oriented within the original perimeter walls as a 2,000 ton per day nickel-copper plant. This plant was expanded to 4,000 tons per day by the addition of t1-Jo rod mills and a 5-1/2 short head crusher in 1959.The Sherridon mill processed its last ore in Sherridon in September 1951 and the first load of nickel concentrate was loaded at Lynn Lake on November 9, 1953 when the railroad arrived at Lynn Lake.The site for the Lynn Lake mill was cleared of overburden in the summer of 1952 and foundations for structural steel and SO!l8 equipment foundations were poured the late summer and fall of 1952 • Steel was erected from January to June 1953. Most of the equipment came in from January to March of 1953 by tractor sleighs. Sane sleighs upset but no equipment was lest through the ice."

Jan 1, 1972

By Vijayakumar Viramuthu, Martin Heinrich

Tower of Lot L, L1 & M, Kuala Lumpur City Centre when completed would stand 700 m tall. This Mega tall Skyscraper would merely be less than 500 m away from the world tallest Twin Tower, the Petronas Twin Tower. From June 2018 to February 2020 BAUER (MALAYSIA) SDN. BHD. constructed 225 nos bored piles with diameters of 2.0 m and 2.5 m for this tower. To comply with the depth requirement of the initial design and the need to have the pile toe 2.0 m above competent bedrock, the drilling equipment was required to be able to achieve a maximum drilling depth of 150 m. Actual piles constructed on site were deeper than 120 m. These dimensions caused superlative challenges which included but were not limited to controlling the open borehole stability over time with polymer, installing 70 t heavy steel cages and pouring up to 550 m³ concrete continuously in conjunction with installation of 88 t heavy kingposts into workable fresh concrete. The piling works were executed with one BAUER BG 48 and one BG 72, the biggest drilling rig globally available.

May 1, 2022