Search Documents

By W. Dingley, G. R. Hoey

"Thirteen Canadian sulphide ore mines were surveyed for corrosion control. The mines visited were a small, yet representative, proportion of this segment of the Canadian mining and metallurgical industry. Information on metallic corrosion and methods used to control it in underground workings and mills was gathered (a) by discussing corrosion problems with company personnel, (b) by examining equipment and structures during under-ground and mill tours, (c) by photographing corrosion sites, and (d) by collecting and analyzing mine water samples.The corrosion survey, which is summarized in the re-port, leads to the following general conclusions. Mine environments are corrosive, particularly when the mine w1a-ter is acidic. Because of a lack of good corrosion control measures, excessive deterioration of equipment due to corrosion occurs in mines. Mill environments are also corrosive, but in some cases good preventive measures are being taken to effectively control corrosion losses.Ways to reduce corrosion losses in sulphide ore mines and mills are discussed. The main areas for more corrosion research and development are selection of materials of construction, protective coatings, cathodic protection, inhibitors, equipment design, and mining and milling practices."

Jan 1, 1971

By G. J. Biefer

"Fatigue and corrosion fatigue measurements were carried out on five commercially available metals -four steels and an aluminum alloy -which are used as structural materials in mine shaft conveyances. In the corrosion fatigue measurements, drain waters collected in the shafts of three different Canadian mines were used as corrodents. The mine waters had been selected on the basis of their relatively large differences in acidity and/ or composition.It was found that the corrosion fatigue strengths of the four steels were similar, despite their differences in tensile properties, and that the type of water used in the tests had little effect on the results. Mild steel showed the highest and most consistent values of the damage ratio (ratio between the corrosion fatigue and the plain fatigue strengths at 107 cycles). The corrosion fatigue behaviour of the aluminum alloy (ASTM Type 6061-T6) was found to differ markedly in the three mine waters. A high damage ratio (i.e., superior performance) was shown in a mine water in which the corrosion attack was uniform; much lower damage ratios were shown in waters which produced localized corrosion attack. Corrosion rates were too low to be deter-mined conveniently by conventional weight-loss methods, but calculations from polarization curves provided a rapid demonstration that corrosion rates were distinctly lower in the mine water which produced high damage ratios."

Jan 1, 1967

By F. L. Wolf

THE catenary system of line construction possesses so many desirable characteristics from the operating standpoint that it has wide application for all types of electric traction. Many steam roads are electrifying sections of their lines, and in most cases are operating both steam and electric locomotives over the same track. This' means that the overhead catenary system is subjected to the severe corrosive action of locomotive smoke, and data concerning the resistance of various alloys to this form of corrosion are very desirable from every point of view. Reliable and specific information and data on the subject of corrosion due to steam and smoke from locomotives are extremely meager and, on this account, extensive service tests, together with accelerated tests, have been made on a number of commercial metals and alloys. The observations and data recorded in this paper are the result of a, preliminary test which was started in 1923 and which has been carried on to the present time. The recognition of the need for even more detailed and accurate data has resulted in the undertaking of another test which has been in progress for about a year. The result of this test will be published in due course. Some years ago The Ohio Brass Co. was asked by one of the large steam railroad companies to furnish data on construction details for a catenary system which it was considering for one of its divisions. The selection of, materials which would give the necessary physical characteristics as well as withstand the severe corrosive action of locomotive gases caused electrical railroad engineers considerable concern. At that time, there were available no specific or authentic data on these important questions: no systematic investigation of the problem appeared to have been made, even though its importance was generally recognized. Such observations as had been made were crude in that they had been limited largely to visual inspection which too frequently is most misleading. However, the scattered information which was collected gave important clues as to how best to start an investigation.

Jan 1, 1930

By AIME AIME

METALLIC corrosion, which results from the chemical affinity of different metals for non- metallic elements, should be considered from both the kinetic and static viewpoints. From the stand- point of statics the metals may be arranged in the order of their affinity for oxygen, chlorine or any other acid- forming element. They may also be arranged in the order of the magnitude of the heat of combination of their corresponding compounds. It is misleading to talk about some metals as "noble," because these relations are all relative; and the order varies for oxygen, chlorine or whatever the element may be. A third way to arrange the metals is by their solution pressures. These three methods indicate that one metal is better under one set of conditions, but not so good under other conditions. Considering the problem from the standpoint of kinetics, the thing which saves most metals is what may be called the sluggishness of reactions. Using organic substances as an example, we know they will all oxidize, but fortunately they do so rather slowly. An increase in temperature always means an increase in the reaction rate, and preventing corrosion at high temperatures is a greater problem than at low temperatures. A second consideration is to avoid all sub- stances which might provoke catalytic action, and as it is generally impossible to foresee what substances might do this, the thing is to avoid all substances other than the main constituents of the alloys. A third consideration is to avoid local electrolytic action, which again indicates the advisability of avoiding the contact of differing substances.

Jan 1, 1926

By George Oprea, Tom Troczynski, Joe A. Rigby, Waiman Lo

The refractory lining of the tuyere line in Peirce Smith converters have usually much shorter life in service than the rest of the lining, above or below it. There are already recognized chemical, thermal and mechanical factors which contribute to the wear of the lining. Our study presents the experimental results on microstructural changes occurring on these tuyere line bricks in a nickelcopper converter. The experimental bricks, after use at the tuyere line, were investigated using SEM/EDS and XRD techniques, to identify the mineralogical changes due to interactions with the nickel-copper matte or fayalite type slag at the process temperatures. The microstructural changes were correlated with physical and mechanical properties of the brick before and after use and a wear mechanism was suggested. Although the matte does not theoretically react with the mineralogical components of the brick, a partial oxidation of the Ni-Cu sulphides was identified using a line analysis by SEM/EDS in the densified layer at the hot face, which allows for mineralogical changes at the matte-refractory interfaces, with a high probability of microcrack formation due to the thermal cycling during use. These microcracks were also identified to open through inter-granular fractures parallel to the hot face, which appeared to be the main cause of lost lining during use. The reactions between the fayalite slag and refractory brick could eventually play a role in chemical dissolution of the brick only in the superficial layer at the hot face, as no slag components were identified deep into the brick.

Jan 1, 2009

By C. Blawert

The corrosion properties of the skin and the bulk of semi-solid processed and high pressure die cast AZ91 alloy were studied in 5% NaCI solution by (a) analysing the corrosion morphology, (b) measuring electrochemical polarization curves, (c) performing electrochemical impedance spectroscopic measurements, and (d) immersion tests at constant pH-values. Using XRD, LM, SEM and EDX to evaluate the microstructure of skin and bulk specimens, the corrosion results were related to the microstructures of the particular alloys. However, microstructure and corrosion performance were found to be similar for both production processes, and only slight but distinct differences were found. Generally, the skin corrosion properties are inferior to those of the bulk, with the exception of the high pressure die cast AZ91 alloy, where the finer microstructure of the skin layer exhibits a better performance as showed by impedance studies and confirmed in long term immersion tests.

Jan 1, 2004

By C. Blawert

In previous studies of various HPDC magnesium alloys we found that the corrosion properties of the skin are inferior in comparison to the bulk, However, this is surprising as one would expect better corrosion properties for the finer microstructure of the skin, In a more detailed study using 2 and 6 mm thick sections from HPDC AZ91 step plates, the corrosion results of the original skin, the slightly removed skin and the bulk were compared, Indeed, the corrosion measurements including potentiodynamic polarization, long term polarization resistance measurements and electrochemical impedance spectroscopy (EIS) revealed a lower corrosion resistance of the original as-cast skin. An explanation for this corrosion behavior was found, on the one hand, in the microstructure concerning especially the amount and distribution of the 13-phase and, on the other hand, in the composition, including the distribution of the most important alloying element Al and of some impurities such as Fe.

Jan 1, 2005

By David Schlain

IN 1942 the Bureau of Mines began to develop the Kroll process for use in the large-scale production of titanium. Titanium and titanium alloys are now commercial metals. These metals are relatively expensive, but It is now evident that they will have important industrial uses and that in many instances these will be related to their remarkable corrosion resistance. This bulletin presents the known corrosion properties of titanium and its alloys in useful form. In marine environments titanium is highly resistant to corrosion and does not pit, or undergo crevice corrosion, stress corrosion, or corrosion fatigue. Titanium is also highly resistant in many salt solutions, including most chlorides. It is very resistant to corrosion in nitric acid solutions. It is also resistant to white fuming nitric acid. However, it may react violently with red fuming nitric acid. In phosphoric acid solutions titanium has rela¬tively good resistance to corrosion, but it has less resistance to sulfuric acid and still less to hydrochloric acid solutions. Titanium corrodes very rapidly in hydrofluoric acid Solutions. It is very resistant to corrosion in many organic chemicals. However, it has only moderate resistance to formic acid solutions and poor resistance inn oxalic acid solutions. Titanium does not corrode in dichloroaretic acid but, corrodes rapidly in 100 percent trichloroacetic acid at 100° C. Titanium is resistant to barium, calcium, magnesium, ammonium, and sodium hydroxides. Titanium is inert in wet chlorine, bromine, or iodine gases. However, in dry chlorine gas titanium reacts rapidly enough to ignite. It also reacts rapidly with dry bromine gas, but, it is resistant to dry iodine gas. When titanium is exposed to red fuming nitric acid solutions with high nitrogen dioxide content and low water content, it corrodes, undergoes stress-corrosion cracking, and becomes pyrophoric. This occurs more readily with some titanium alleys, such as titanium-8 percent manganese. A fresh titanium surface immersed in water or in an aqueous solution and in contact with an oxygen-rich atmosphere under sufficientt pressure is unstable and will ignite spontaneously. Inherently an active metal, titanium has a tendency to become less active in environments containing oxidizing agents such as air, oxygen, chlorine, or ferric, cupric, or platinic ions. Titanium is more noble than most structural metals in roost, environments and its excellent corrosion resistance is generally not, affected by contact with these metals. However, some of the other metals corrode faster because of contact with titanium. Titanium undergoes anodic polarization readily, so that even when it is the less noble member of a galvanic couple it may corrode less because of the contact. Titanium alloys often have corrosion properties and electrochemical characteristics similar to those of commercially pure titanium. Titanium alloys containing noble metals, zirconium, molybdenum, vanadium, tantalum, or copper sometimes have better corrosion resistance than pure titanium.

Jan 1, 1964

By Darina Manova

Plasma assisted surface modification methods have been used to nitride stainless steels in order to enhance hardness and therefore the lifetime of industrial components. Nevertheless, the corrosion resistance is not always preserved since it is very sensitive to the process parameters, either in implantation or in thermochemical diffusion techniques. AISI 316L stainless steel was plasma nitrided using three different techniques: Low Energy Ion Implantation (LEII), Plasma Immersion Implantation (PI3) and conventional DC pulsed plasma nitriding (DCPN). For each method several parameters were tested and some of them were selected to achieve the so called S phase of about 3 µm thickness and no nitrides precipitation. The nitrided layer was characterized with OM and SEM. Hardness was assessed on the surface with Vickers indenter and 25 g load. XRD was performed to characterize the S phase and to detect other phases if present and electrochemical corrosion tests were carried out in 3.5% NaCl solution. Although the S phase thickness in the three groups of samples was comparable, hardness was not and neither was the corrosion resistance. The PI3 samples were the hardest with the best performance in corrosion experiments, resulting in a higher breakdown potential and lower currents.

Aug 8, 2018

By C. Juers

Laboratory chromate coating was applied on AM50 and AZ91D alloys and compared to phosphate-permanganate one. Evaluation of the corrosion behaviour was performed using electrochemical DC and AC methods in ASTM water D1384-87. This electrolyte was chosen because it was moderately aggressive and found to give generally good correlations with long period exposure results in atmospheric conditions. Electrochemical impedance spectroscopy was used to determine more accurately the corrosion rates from the analyses of the high frequency capacitive loop. Anodic polarization was applied in order to evaluate the pitting resistance of the different coatings. These results were correlated with weight loss data evaluated from experiments performed by immersion tests in ASTM water D1384-87 and climatic cyclic chamber tests.

Jan 1, 2006

By J. van der Merwe, D. Tharandt

The corrosion behaviour of 304L stainless steel laser-cladded with various amounts of ruthenium (Ru) was evaluated in solutions of sulphuric acid and sulphuric acid plus sodium chloride at 25°C and 45°C by open-circuit potential and cyclic potentiodynamic polarization tests. In general, the addition of Ru to the stainless steel increased its corrosion resistance in 1 M H2SO4, as well as in 1 M H2SO4 plus 1 wt% NaCl. This was observed for a number of parameters such as corrosion rate, corrosion potential, open-circuit potential, and current density. However, increasing the amount of Ru added beyond a certain level did not result in further improvement in corrosion protection. For each environment there is an optimal Ru concentration for the best corrosion protection. For example, in 1 M H2SO4 at 25°C, 2.44 wt% Ru shows the least active surface in terms of corrosion. Further research into ruthenium coatings on stainless steels is recommended.

Jan 1, 2015

By Rodrigo Perito Cardoso

Low-temperature nitriding of stainless steels is applied to obtain wear resistant surfaces without losing its corrosion resistance. The treatment consists in introducing nitrogen into the steel surface avoiding chromium nitride precipitation. The corrosion resistance of martensitic stainless steels is expected to be improved if the treatment parameters are correctly selected. It can be related to ?Fe2-3N and a'N phase formation on the treated surface. In the present work the influence of the pretreatment and treatment temperature on corrosion resistance of plasma nitrided AISI 420 steel samples is studied. Annealed, as-quenched and 400ºC-tempered samples were nitrided at 300, 350, 400, 450 and 500°C, for 6 h at 600 V. The pressure was 3 Torr and the gas mixture was composed of 70%N2, 20%H2 and 10%Ar, at a gas flow rate of 3.34×106 Nm3s-1. Plasma was generated using a square-wave pulsed DC power supply and the sample temperature was controlled by the duty cycle. The modified layers were characterized by optical microscopy, X-ray diffraction and microhardness measurement. The corrosion resistance was studied by electrochemical characterization, by means of Open circuit potential and Anodic polarization curves. The maximum surface hardness was achieved at 400°C. This temperature seems to be near the limit temperature for low-temperature treatment aiming to improve or at least to keep unaltered the corrosion resistance in relation to that verified for non-treated steel samples. Results confirm that the pretreatment and treatment temperature significantly affects the corrosion resistance of the treated surface.

Aug 8, 2018

By Gabino Preciado, Louis Sandbak

Corrosion has long been identified as a potential risk to the long-term ground support stability due to degradation of internal ground support elements such as rock bolts but also to surface support from mesh, straps, bolt plates, and ancillary support of utilities such as hangers. The emphasis is to understand the corrosion mechanisms on the primary ground support elements and any supplemental steel or arch sets. The water and chemical processes from oxidation(rust), stress corrosion cracking, and even the electrical charge created during these reactions contribute to the corrosion of the steel support elements. The main goals are to mitigate the effects of corrosion and to be able to predict those areas of high water or high sulphide for potential rehab maps. It is also essential to identify and classify the visible corrosion as part of damage mapping and provide bolt testing to those areas of suspected internal damage from corrosion. This is important to get an estimate of the support longevity or expected life before rehab to minimize the overall cost of the operation.

Feb 1, 2024

By A. -M. Lafront

The corrosion resistance of die-cast and freely-solidified and electromagnetically-stirred thixocast AZ91D alloy has been studied using electrochemical noise technique in a 0.05M NaCI solution at pH 6.1 and 25°C. Specimens polished at different depths were immersed for a period of 75 min in order to assess the influence of the microstructure on corrosion kinetics and morphology. At depths between 10 and 50 µm (skin), all specimens showed general non-uniform corrosion with the lowest corrosion resistance. Between 100 and 200 µmn (interior skin), the observed corrosion was accompanied by superficial undefined pits due to metastable pitting. The corrosion form for 100-200 µm gave the best corrosion resistance. Stable pitting corrosion was observed beyond 400 µm deep on the bulk specimens. The skin of all thixocast specimens prepared billets showed a more corroded surface than that of die-cast. The interior skin as well as the bulk specimens showed better performance than that of the die-cast specimens.

Jan 1, 2007

By R. F. Lynch, F. E. Goodwin, A. F. Skenazi

"The Gal/an alloy has been developed for continuous galvanizing of steel. The choice of the eutectic zinc-aluminum alloy with addition of misch metal gives a coating with specific characteristics as far as structure, analysis, surface chemistry and surface morphology are concerned. The performance of the uncoated Galfan coating is superior when compared to conventional galvanized particularly for corrosion resistance and ductility. For coil coating applications, these two assets are of the utmost importance but in order to benefit from these two advantages, good paint adherence and high resistance to edge creep and blistering have to be obtained. Despite Galfan's unique features compared to other zinc based or aluminum zinc based coatings, existing pretreatments and painting conditions are used with only minor modifications in order to assure good adherence and edge creep resistance. With compatible processing, Galfan can outperform galvanized and Galvalume as a substrate for coil coating as is demonstrated with various test results.IntroductionThe technical and commercial development of Galfan, a 95% zinc-5% aluminum-0.1% lanthanum-cerium hot-dip coating for steel, has been rapid. From its identification as a promising coating in late 1980, it has evolved from a research product to a fully commercial product with over 100 000 metric tons of coated sheet produced to date, and another 90 000 tons, at minimum, scheduled for 1986. The great majority of tonnage produced to date has been coil coated for use in building panel , appliance, and similar applications. Much technical work has been done to determine the suitability of Galfan for these applications and the proper way of processing sheet for best results. The present state of knowledge is discussed in this paper, along with some recent applications which are given asexamples"

Jan 1, 1987

By John L. Hatton

The author will introduce and describe the nature of Fiberglas-Reinforced Plastics. Successful applications of corrosion-resistant structures will be shown and described, including pipe, ducts, tanks and other equipment. These structures are generally designed to handle corrosive liquids and gases and have proved both satisfactory and economical in service in various industries in Canada. The specification of structures will be discussed in relation to materials, construction and workmanship, physical properties and methods of testing.

Jan 1, 1970

By S. H. Ash

NINE-TENTHS of the total anthracite deposits of North America are in Pennsylvania. Corrosion of pumping equipment by acid mine waters has been experienced at tremendous cost by mining companies in the anthracite region of Pennsylvania, for many years in many ways. The design and specifications of the large centrifugal pumps as provided in the proposed mine-drainage system (7-35, 45, 46, 48, 54, 64, 70, 71)° make it imperative that a metal or alloy be recommended that has the highest corrosion resistance and, at the same time, acceptable properties suitable for general workability (welding and machining). This report presents data on the corrosive and erosive effects of acid mine waters in the anthracite region on metals and alloys for pumping equipment and drainage facilities necessary to remove or control this water.

Jan 1, 1955

By Bill Birch, Toby White, Ian Brown

costs/benefits of electronic detonators and measure their effects on primary crusher productivity. 9 blasts (3 shock tube blasts, 6 electronic blasts). Measured electricity consumption & primary crusher throughput. Change to Electronic Detonators resulted in a 7% reduction in primary electricity costs and a 15% increase in primary crusher productivity.

Feb 1, 2020

By J. A. Bullington

Mr. Chairman and Gentlemen: Some of you men may know who are familiar with what we have been doing in the C. F. & I. the last three years, that we have revamped our entire method of cost accounting from the pit bosses' report through to the final report of the president. The basic ideas involved in our cost system are not ours. They were given us by one of the best management and industrial engineering concerns in the country-at least they have that reputation. All I can do now is to try to pass on to you some of the ideas we have from various sources and the methods we have used in teaching those ideas to our coal men on cost accounting. This will not be a technical paper. I tried to put it in language we could all understand, and I hope I will be talking the same language that you gentlemen talk when you think about the cost of your coal in your own mines. Accounting of all kinds is classed as overhead expense, and as overhead expense we must justify its cost by the service it gives the rest of the organization. That brings us up to the problem of making the cost department pay its own way, just the same as the power plant has to pay its own way, and we have gotten away from the old idea of cost accounting in that it is sufficient within itself. The cost sheets are only so good as they enable the operating man to reduce his costs. The cost sheets are only just so much work for the cost department, and if they do not help the operating man to control his costs, we figure that is so much work wasted. The cost department works for the operating department.

Jan 1, 1931

By Ronnie Melker, Joel Webster, Daniel Belardo, Thomas Hyatt

Quality assurance of drilled shafts is highly dependent upon the construction practices used during the excavation and concrete placement process. When performed under slurry, challenges are presented in maintaining borehole stability and placing a uniform and continuous concrete column. An integral part of the construction operation is to evaluate the as-built integrity to verify the drilled shaft is capable of safely transferring the required loads to the subsurface. One such case is exemplified by a project involving the expansion of an existing public transit rail line. The expansion required the construction of a new bridge bent supported by seven 5-ft diameter drilled shafts of various lengths. The specifications for the project required both Cross-Hole Sonic Logging (CSL) and Thermal Integrity Profiling (TIP) for drilled shaft integrity evaluation. Both of these post-construction non-destructive tests (NDT) are designed to detect anomalies or the presence of regions with reduced concrete quality. However, the implementation and methodologies of performing each of these NDT methods are significantly different. Cross-Hole Sonic Logging uses ultrasonic signals emitted from a transmitter in one access tube to a receiver in another access tube. Thermal Integrity Profiling measures elevated concrete temperatures during the curing process using embedded thermal wires. Both test methods require different access details and therefore have different costs associated to the contractor or owner to perform. This paper provides a detailed comparison of these NDT methods as performed on these seven drilled shafts. The associated financial and time costs to perform each method are compared and the results are discussed in detail. INTRODUCTION Drilled shafts are a fundamental deep foundation element that can be designed to resist large bending moments as well as to transfer large compressive axial loads through weaker upper soils to competent soils or rock below. Often times when the upper soils are very soft, lateral support by casing or slurry, or a combination of both, may be used to hold back the softer soils from collapsing into the hole before concrete has been placed. Due to the blind nature of drilled shaft construction and the qualities issues that may arise during the placement process, it is essential for design engineers to specify non-destructive testing (NDT) to assess the quality of the as-built drilled shaft. CSL and TIP testing are two NDT methods designed to detect areas of lower quality concrete or soil inclusions throughout the length of the drilled shaft and determine its overall quality. Each method uses different technologies and methods to achieve the results required to determine the as-built condition of the drilled shaft.

Jan 1, 2019