Search Documents

By J. Mark Gronseth

The instantaneous shut in pressure often times is not a well defined feature of pressure-time records from in situ stress determinations by hydraulic fracturing. As the applications of in situ stress data become more sophisticated, the grea5er the need for an unambiguous method with which to identify the instantaneous shut in pressure becomes. Controlled experiments suggest that the instantaneous shut in pressure should be equated with the pressure at the inflection point of the pressure-time record following shut in. A method for determining this value is presented. Often times the minimum instantaneous shut in pressure determined after several pressurization cycles is the best estimate of the stress acting perpendicular to the fracture plane.

Jan 1, 1982

By Norman F. Schulz

The Davis magnetic tube concentrator is a laboratory machine designed to separate a small sample of pulverized magnetic iron ore into magnetic and non-magnetic fractions. It was developed in 1921 by mechanization of a test previously performed manually. (1)(2)(3)(1) No significant changes have been made in the design of the apparatus since that time. The Davis magnetic tube test continues to serve as a practical basis for judging the amenability of an ore to magnetic separation and for controlling magnetic separation plant operations. The apparatus consists of an inclined cylindrical glass tube supported adjacent to closely spaced pointed poles of a powerful C-magnet. (Figure 1). To conduct a tube test, a sample of a suitably prepared ore is poured into the water-filled tube. With wash water flowing through, the tube is oscillated to gradually reject the weakly magnetic ore particles until the desired degree of separation is attained. Both the magnetic concentrate and the tailings may be recovered for examination.

Jan 1, 1963

By M. Khodadazadeh, K. G. van den Boogaart, T. Leißner, L. Tusa, J. Gutzmer, R. Gloaguen, M. Kern

Ore sorting is a technology that is increasingly used to process primary raw materials. Timeconsuming and expensive empirical state-of-the-art test work is carried out to assess whether the use of ore sorting for the enrichment of a particular ore makes technical and economic sense. With the innovative simulation-based approach presented here, it is possible to direct the selection of a suitable sensor based on quantitative mineralogical and textural data, thus avoiding much of the empirical studies. Required data can be collected quickly and cost-effectively using available methods of automated mineralogy. The obtained parameters such as mineral grain size distribution, modal mineralogy, mineral area and mineral density distribution have been utilised in this study to simulate the prospects of success of ore sorting, applying different types of sensors. Empirical tests with commercially available sensor systems have been conducted to experimentally validate the predictions of the simulations. The estimation of the target mineral grade can be further optimised by the use of machine learning algorithms for the integration of automated mineralogy data and sensor data. The approach can easily be adapted to other types of raw materials and thus has great potential to become a key technology for the optimisation of processing experiments. Keywords: Automated mineralogy, hyperspectral imaging, machine learning, ore sorting

Jan 1, 2020

By M. Shamsi, M. Nehring

One of the most challenging aspects in semi-mobile in-pit crushing and conveying (SMIPCC) system design is determining the optimum depth at which to change from a purely truck-based haulage system to a conveyor-based haulage system. We used scenario analysis to determine the optimum transition depth between a truck and shovel (TS) system and a SMIPCC system. Traditional pit-limit algorithms were used to generate the final pit limit on a copper deposit, which was then divided into four pushbacks. The final operating pushbacks (phases) were designed for both TS and SMIPCC. The end depths for each phase are viewed as candidate transition points to switch from the TS to SMIPCC haulage system. Economic calculations were applied for five different scenarios, including adopting SMIPCC from the outset (pure SMIPCC), after the first, second, and third phases, and finally not using the SMIPCC system (pure TS) at all. The analysis indicates that the second scenario, at a depth of 335 m, results in the lowest cumulative discounted cost (CDC). In this case, the CDC is 17.6% lower than that for the pure TS scenario and 10.7% lower than for the pure SMIPCC system scenario.

Sep 1, 2021

By Kourosh Shahriar, Kazem Oraee, Ezzeddin Bakhtavar

"In this paper, a relationship between dependant parameters and the crown pillar thickness is first introduced. This relationship defines geotechnical problems caused by thin pillars and economic considerations created by pillars that are thicker than the optimum size. For this purpose, a dimensional analysis as an effective physico-mathematical tool was used. This technique restructures the original dimensional variables of a problem into a set of dimensionless products using the constraints imposed upon them by their dimensions. A model is hence introduced that calculates the optimum pillar thickness. The relationship introduced here and the method applied can be used by mining engineers in all situations where a combined open-pit and block caving method is deemed to be the most appropriate mining method.INTRODUCTIONMany deposits can be mined entirely with the open-pit method; others must be worked underground from the very beginning. In addition, there are the near-surface deposits with considerable vertical extent. Although they are initially exploited by the open pit method, there is often a ""transition depth"" where decision has to be made about changing to underground methods.Some of the biggest open-pit mines worldwide will reach their final pit limits in the next 10 to 15 years. Furthermore, there are many mines planning to change from open-pit to underground mining due to increasing extraction depths and environmental requirements. In this way, it is likely that block and/or panel caving will enable the operations to continue achieving a high production rate at low costs as an underground method (Bakhtavar et al., 2009).In these cases, it is often necessary to consider a crown pillar beneath the transition depth (open-pit floor) before starting an underground caving stope method (Figure 1).There are generally two kinds of crown pillar: a ""surface crown pillar"" and ""crown pillar between open-pit and underground mining."" In general, they both play the similar role in mining. Since the primary purpose of a surface crown pillar is to protect surface land users, the mine, and those working in it from inflows of water, soil, and rock; it is vital that the surface crown pillars remain stable throughout their life. When a crown pillar could potentially remain between open-pit and underground mining it is specially proposed to prevent water entering from the open-pit floor into the stope, as well as to reduce open-pit wall and floor caving."

Jan 1, 2010

By Lloyd R. Nelson

Selective carbothermic reduction is the preferred method of treatment of electric arc furnace (EAF) dust (listed hazardous waste, K061). The process maximizes the recovery of recyclable constituents by concurrent production of saleable zinc metal (directly condensed from the furnace off-gases), an innocuous, disposable iron oxide-rich slag, and some metallic iron. Results of a mineralogical investigation of a foaming slag produced during selective carbothermic reduction treatment of EAF dusts are presented. Wiistite and tricalcium silicate were identified by reflected light microscopy as the primary crystalline phases contained in a glassy matrix, but this technique failed to reveal any solid phases that could have significantly contributed to foam stability. It was concluded therefore, that the foam had been unstable, and had been primarily generated by copious gas evolution associated with the sudden reduction of the slag by an inadvertent addition of carbonaceous reductant. This is consistent with the susceptibility to foaming, when subjected to sudden excesses of carbon, of the slags produced by selective carbothermic reduction, because they still contain unreduced components such as iron oxide.

Jan 1, 1994

By Charles A. Beasley

Increased technical and legislative analysis by all parties of interest could result in more efficientand better directed regulatory legislation in the mining industry. Efforts to forestall or frustrate legislation through massive lobbying and public relations efforts are seldom effective over time and often lead to more stringent and far reaching legislation than necessary. The Federal Coal Mine Health and Safety Act of 1969 is perhaps an outstanding example of such insufficiences; a future example may well be regulatory surface mine legislation. Although a lack of extensive hard data seldom enables rapid or sophisticated analysis early in the legislative process, even preliminary analysis may be sufficient. Simple statistical analyses of available data, assessment of the legislative rationale, and subjective appraisal of other non-quantifiable constraints to improved mine safety. An average of 115 underground fatalities at an exposure frequency rate of 0.67 can be reasonably expected in the immediate future, under existing levels of technology, degree of regulation, and economic conditions. If gross unrefined estimates of 6 preparation plant, 5 surface, and 30 strip mining fatalities are assumed, the total fatality industry level could be expected to approximate 156 Serious professional, economic, and technical constraints within the the industry probably preclude any major decrease of these accident levels within the near future

Jan 1, 1972

By P. J. Lunder, R. C. Pakalnis

This paper presents the results of research that has been undertaken in order to develop an improved method of determining the strength of hard-rock mine pillars. Pillars are found in various shapes and sizes in all underground mining operations. Prudent engineering design requires that if pillars are to perform as desired, both the pillar strength and the pillar stress must be determined. A detailed pillar stability study has been combined with an extensive database of published pillar case histories (178)resulting in a new “hybrid” pillar strength formula, “The Confinement Formula”, that utilizes classic strength of rock methods combined with empirical methods. “The Confinement Formula” utilizes a “mine pillar friction term” calculated from the average minor/major stress ratio with-in the pillar core. Statistically, the new formula provides better results at predicting pillar strength for the combined database than the best empirically ft pillar methods that currently exist. “The Confinement Formula” allows for the determination of the strength of mine pillars with an increased level of confidence over previously applied methods.

Jan 1, 1997

By Monika Patrycja Polak - Micewicz

This paper presents an approach for estimating the fatigue life for the base of powered roof supports (shield) manufactured by the FAZOS roof support company. FAZOS?s powered roof supports are designed to operate on an inclined coal seam in full caving with a medium, strong roof strength. This shield support is utilized in conjunction with a shearer and face conveyor for a complete longwall mining system. To design shield support, it is essential for contractor to know the physical (hardness, toughness, etc.) and mechanical properties of material (tensile strength, Young?s modulus, etc.) used for the shield support as well as the geotechnical properties of the mine site. The fatigue strength of the shield support material depends on the mean stress, alternating stress, cycle frequency, transport dimensions, mine environment and other factors. In order to estimate the fatigue life for a powered roof support system, it is assumed in this paper that the support must keep the roof stable in the mine under variable load cycles. The approach selected in this study contains Goodman?s model (Goodman, 1899) for all blocks in the design housing which is subjected to sinusoidal load. On this basis, the degree of fatigue damage was calculated and compared to the results of experimental tests. It will be shown that there is a significant detrimental effect on the fatigue life of the base of the powered roof supports due to geometrical notches. The Ramberg-Osgood model and damage accumulation rule (Palmgren-Miner) (Miner M., 1945) were used and numerical analyses were conducted, utilizing ANSYS finite element software. These analyses play a very important role in longwall casing design. The proposed method allows assessment of the yield state and forecast of the structure cracking, taking plastic strains occurrence into account. The presented method is universal and can be applied for fatigue life estimation of other subassemblies of powered roof supports. The final portion of the paper presents results of variable amplitude loading simulations on the S355N and S690Q steel used to make powered roof supports. The results of the physical tests were compared with the results from finite element methods. The proposed approach to calculate fatigue life gives the best correlation between the experimental results and calculated values of fatigue life for the powered roof support base. Finally, the design process uses a simple approach to predict fatigue life in a short time, reducing design costs and providing longer service life for roof supports.

Jan 1, 2012

By M. Arlandi-Rodríguez, and A. García-Berrocal, A. Alonso-Jiménez, C. Lopez-Jimeno

Spain is a major producer of dimension stone, which is one of the most important industrial sectors in the northwest of Spain. This justifies the maintenance of these industries, although the technical and environmental requirements for their continuity are increasingly demanding. The main target of this paper is to present a new methodology in order to obtain k-ratio stress values on the basis of flat jack measurements and finite element numerical back- analysis with Rocscience© RS2 software. Continuous iterations were performed to try to find a relationship between the k₀ and the measured stress in the tunnel roof and sidewalls. It focuses on technical aspects of the method for designing mine chambers in the slate industry that were previously mined by open pit methods. The size of the chambers impacts the operating cost, and the dimensioning of a correct support ensures better efficiency and safety. Correct knowledge of the k₀ therefore is critical for the design of the support. The proposed new method entails a simplification of the classical procedure for estimating the k-ratio.

Sep 1, 2022

By A K. Ghosh, J Chung, E Topal, M Asad

"Many open pit (OP) mines with considerable vertical extent are approaching the end of their life-of-mine; some of them are seeking the opportunity to make the transition from OP to underground (UG) mining. The decision on the best location for transition from OP to UG mining should be addressed at the strategic mine planning stage. Conservatively, the transition to UG mining is considered near or after the exhaustion of the reserve within the ultimate pit.However, if UG is evident and exclusively viable from the inception, defining the best location for the transition through a conservative approach may not be an optimal option to explore. This clearly establishes the need for a mathematical model that aims to maximise the project value and considers OP and UG mining with crown pillar (CP) requirement simultaneously. Underground mine layout varies from one UG mining method to the other, and consequently the variation in the location of transition is eminent. Thus, focus on the selection of UG mining method must be a part of this analysisThis paper presents an implementation of an integer programming (IP) based mathematical model that evaluates the changes in mining layout and the project value under possible variation in the transition point from OP to UG mining for stoping and block caving methods. An IP problem is a mathematical optimisation or feasibility method in which some or all of the variables are restricted to be integers. The outcome of the implementation reflects that mining strategies with OP transition to stoping and block caving methods generated higher values than OP-only mining strategy. The case study not only demonstrates the difference in mining layout for both stoping method and block caving method, but also reflects that a joint consideration of OP mining, UG mining and CP placement helps to achieve maximum project value and resource utilisation.Citation:Darbritz, J, 2016. Remediation of Wall Failure at Kalgoorlie Consolidated Gold Mines' Golden Pike Cut-back 2016, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 96–103 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By Hiroshi Ono

"By newly developed ICP method, trace amounts of As(III), As(V) .,Sb(III) and Sb(V) were precisely determined within accuracy of sub ng/ml. As(III) and Sb(III) were separated from As(V) and Sb(V) by extracting into ·xylene as diethyldithiocarbamate complexes using diethylammonium diethyldithiocarbamate (DDDC), and then back-extracted into nitric acid for a quantitative determiruition by ICP-AES equipped with hydridegeneration system The recoveries of As(III) and Sb(III) were satisfactory throughout the extraction with 0.04mol/l DDDC in xylene from lmol/l hydrochloric acid solution and the back-extraction with 7 mol/l nitric acid. As(V) and Sb(V) were reduced to As(III) and Sb(III) by ascorbic acid and potassium iodide, and their quantities were determined as mentioned above. The detection limits were found to be 0.58ng/ml for As(III), 0.63ng/ml for Sb(III) using 50ml of a sample. The proposed method was applied to analysis of the real sample.Introduction In drain, arsenic(AS) concentration is prescribed below 0.lmg/l, so As must be removed. As is existed at .the form of As(III) or As(V) in solution. For t1Jeir difference of chemic;µ property, it is not easy to remove As in solution. So it is an urgent necessity to develop for determining concentration of As(III) and As(V). Antimony( Sb) has resemblance .chemical property to As. So Sb was experimented the same as As.The separation and determination of As(III) and As(V) have been carried out using several methods, such as ICP after copreclpitating separation, HPLC, direct hydride generation atomic absorption. However these methods have some problems. One of main problems is that HPLC and direct hydride generation atomic absorption methods are influenced by coexisting elements."

Jan 1, 2000

By B. K. Slone

The depth at which it becomes more economical to use slope access as opposed to box-cut access for near-surface coal reserves, termed "transition depth," can be established for a given coal property by considering cost estimates for those parameters that determine respective access method. Fourteen parameters that influence access cost were identified and ranges determined. A Transition Depth Formula was developed to permit determination of the better method of accessing a reserve, given such information as highwall slope, road width, total bench width, pit dimensions, road grade, belt component costs, pumping costs, and cost of overburden removal and reclamation. In most cases, in Appalachia, studies indicate that the transition depth ranges between 20 and 30 m.

Jan 1, 1998

By Donald R. Williamson

Statistical studies at Cyprus Pima Mine indicate that samples from 22 blastholes are necessary for determining average copper grades, within a desired range of precision, for mine-model blocks by arithmetic averaging. The average number of holes in such blocks is 14. Many considerations show that more holes will not be drilled for sampling. A way to determine block grades more reliably than by" arithmetic averaging was sought. Thus far arithmetic averaging has proven to be the best procedure for the particular operation characteristics despite the small number of samples. It naturally follows that expenditure of great effort in sampling blasthole cuttings is unwise.

Jan 1, 1977

By F. E. Senftle

Introduction The usual laboratory methods of uranium analysis are either tedious, time-consuming chemical procedures or elaborate physical methods requiring sensitive equipment. There is thus an urgent need for a method of estimating the uranium content of ore samples by approximate analysis in the field. When a new property is being developed, it is desirable to know, with the least possible delay, the uranium content of channel samples in order to guide the diamond drilling and digging operations. Prospectors, too, require approximate analyses of their hand specimens to evaluate their discoveries. To satisfy the demand for these types of analyses, several field procedures have been tried. Two general plans can be followed. One is fast but will yield only a rough estimate. The other is slightly longer but, if done carefully, will give an assay probably within 10 per cent of the true value. For field operation it is necessary to strip the more accurate laboratory methods of analysis of all refinements because of the limited equipment and skilled techniques at hand. Most of the corrections normally applied, with the exception of that for equilibrium, will not alter the gross analysis to any appreciable extent. When uranium atoms in pitchblende disintegrate, they break down into other radioactive elements, and eventually the number of elements being formed is equal to the number breaking down. The ore is then said to be in equilibrium. Certain geological processes, however, such as leaching, may selectively remove some of these elements and hence reduce the radioactivity of the ore sample. The ore is then said to be out of equilibrium. The field analysis may then be in error by as much as 50 per cent since the apparatus is calibrated with standards that are in equilibrium. However, such a large error due to loss of equilibrium is the exception, and in most cases uncorrected field types of analyr.is are justified.

Jan 1, 1949

By B. A. Slaker

The ability to detect and quantify ground movements in underground mine workings is of the utmost importance to the safety of miners and continuity of operations. Rib sloughage is one of the most common forms of underground deformation. Remote sensing techniques, such as laser scanning, can be used to quantify this rib sloughage, by recording precise, timelapse point clouds of mine workings. In order to determine sloughage volumes and locations, two sets of laser scans were performed 42 days apart at a working section of an underground limestone mine. During this period, significant sloughing and scaling occurred, allowing for differentiation between the initial and final point clouds. Volumetric changes of 2.3-2.6 m3 were detected on rib faces during the time-lapse study. In addition, displacement in the mine roof was, as expected, not detected, suggesting well surveyed scans and an appropriate scan resolution.

Nov 1, 2013

By Cynara Christ Klippel

Devido às exigências de teores de fosforo cada vez menores no aço, o processo de desfosforação tem ganhado destaque nas indústrias. Para aproveitamento das melhores condições termodinâmicas a etapa mais eficiente para o processo de desfosforação ocorre no ferro-gusa. Esse trabalho utilizou quatro misturas iniciais de composição definida com base na literatura, juntamente com o ferro-gusa para ser simulado o processo de desfosforação. A simulação foi feita através do software de cálculos termodinâmicos FactSage e através dos resultados obtidos do programa foram feitos cálculos para avalição da eficiência do processo. Além disso, também foram feitos cálculos baseados na literatura para comparação de resultados e estudo mais aprofundado dos resultados. Os resultados obtidos comprovaram a teoria inicial de que menores temperaturas favorecem o processo.

Aug 17, 2017

By Breno Totti Maia

A principal ferramenta de controle do processo BOF reside na regulagem dos parâmetros de sopro de oxigênio. As condições ótimas desse processo envolvem diversas variáveis, como vazão de oxigênio, distancia banho lança (DBL), número de furos para a saída de oxigênio na lança, entre outros fatores. Através de uma análise visual da penetração do jato e do volume movimentado, foram analisados os comportamentos para cada configuração de sopro entre diferentes combinações de bicos multifuros (3 a 6 furos), para uma distância banho lança (DBL) e vazão constantes. A análise dos parâmetros de interação entre o sopro e o banho líquido composta pelas frações de metal e escória, representados respectivamente por água e óleo de parafina é o principal objetivo deste trabalho. Foi necessário desenvolver nova metodologia para a determinação da penetração assim como proposta de nova fórmula e ajuste da constante empírica, fator K. As maiores penetrações foram alcançadas com os bicos de 3 e 4 furos. Para a configuração de 6 furos, foram encontrados os menores valores de penetração e maior volume de zonas de baixa movimentação em relação aos parâmetros estabelecidos.

Aug 17, 2017

By Roberto Carneiro da Silva, José Geraldo da Silva Moreira, Eder Quental de Araújo, Patrick Petronio de Castro Andrade

Os fornos de reaquecimento são equipamentos comumente utilizados na indústria siderúrgica para aquecimento de produtos intermediários produzidos pelo processo de lingotamento. A operação correta desses equipamentos pode ser medida através de sua produtividade, seu consumo específico e seu rendimento metálico. Isso se torna ainda mais desafiante quando se trata de fornos multicombustível, e de uma siderúrgica integrada de grande porte como é o caso da Gerdau Ouro Branco, que possui 5 fornos de reaquecimento para atender a 5 diferentes laminações onde a disponibilidade de gases combustíveis é variável para cada forno. Dessa forma, esse trabalho traz uma metodologia de otimização capaz de determinar qual a melhor mistura de combustíveis e Poder Calorífico Inferior do Gás Misto (PCIGM) para operar os fornos de reaquecimento em diferentes situações e necessidades operacionais e de produção.

Aug 1, 2019

By Verônica Scarpini Candido

O estudo da composição mássica de cerâmicas vermelhas é de extrema importância para a produção de peças com propriedades tecnológicas aceitáveis. Nesse contexto esse trabalho tem por objetivo determinar as propriedades tecnológicas de cerâmica vermelha para fabricação de blocos de vedação. Dois tipos de argila foram usados, argila forte e fraca, para a confecção dos corpos de prova que foram moldados por prensagem uniaxial. Após essa etapa foram determinadas a absorção de água e a resistência em flexão. Os resultados mostraram que a massa composta por 50% de argila forte e 50% de argila fraca apresentaram os melhores resultados de resistência à flexão. Assim, o estudo mostrou que todas as massas estudadas atendem aos requisitos mínimos exigidos por norma e que a massa composta pela mistura das argilas apresentou o melhor desempenho mecânico tecnológico.

Oct 30, 2017