Search Documents

By M. Mpofu, G. Stenzel, F. Magweregwede, B. Maphalala, T. Kgarume

Surface coal operations in which mining activities are conducted above old underground workings experience hot holes after drilling. In a coal mine, hot holes are defined as shot holes, which after being drilled have an in-hole ambient temperature of 40°C or above or show a temperature increase of 3°C or more during monitoring. Hot holes and other cavities, such as cracks, pose health and safety risks to workers, such as exposure to hot air and high concentrations of noxious gases released from these holes. In addition, workers may be exposed to premature detonation of explosives caused by in-hole temperature increases and chemical reactions. To this end, Coaltech Research Association commissioned a project to develop a Best Practice Guideline for the management of hot holes. This paper is a compilation of the activities conducted in the development of the Best Practice Guideline between 2021 and 2022. The activities included a review of standard operating procedures and hot-hole temperature-measuring and -monitoring devices, and the assessment of current hot-hole procedures at selected mines. The results indicated that management of hot holes requires a focus on pre-emptive risk assessment of mining blocks, identification of hot holes using the correct temperature-measuring devices, and continuous monitoring of hot holes from the time of drilling until just before blasting. Hot-hole management accessories, such as polyvinyl chloride sleeves, were found to be effective in insulating the hot-hole emulsion from the rock mass temperature, thus preventing the potential for premature detonation.

Sep 9, 2024

By W. Pulles

Mining can adversely affect water quality and poses a significant risk to South Africa?s water resources. Proactive management of environmental impacts is required from the outset of mining activities in order to reduce this risk. Major strides have been made over the last 7 to 8 years, by both the Department of Water Affairs & Forestry (DWAF) and the mining industry, in developing strategies and management plans for the effective management of water within the industry. This has largely been achieved through the development of joint structures where problems have been discussed and addressed through cooperation. This process, which was started around 1991, has continued through to the present time. The mining sector management strategy has been developed at a number of different levels as follows: ?A detailed Management Plan, that sets out strategic objectives, broad strategies and functional and organizational arrangements. ?Operational Guidelines, that define and document specific operational procedures. ?Technical Guidelines, that define and document best practices for pollution prevention and impact minimization from mining operations. The Technical Guidelines consist of Best Practice Guidelines (BPGs) and Regulations.

Jan 1, 1999

By Brian E. Perrine

Underground mining requires a variety of specialized equipment. With ever-changing mining conditions and methods, some mines have had to resort to purchasing existing industrial equipment and adapting it for underground use. Since this equipment is not made for underground mining or their specific task, the result is often lost time, money, and sometimes an unsafe working condition. One such application is the setting of a CAN. A CAN is a type of cylindrical secondary roof support made from a cement composite and encased in steel. The CAN has become popular because of its simple one-piece design that can handle heaving and sagging better than other available designs. ?Because of this exceptional ability to sustain load through extended convergence and displacement, the CAN is one of the most robust and stable standing supports in use today.?It also promotes better air flow due to the size and shape of the CAN. CAN size and weight have increased over time to handle more difficult mining conditions. Significant down time and inefficiencies with existing CAN setting machines at Twentymile Coal were directly due to the item in use not being designed to be task-specific. They were undersized with very limited movement. The miners had to take extra steps and precautions when setting CANs. Maintenance delays were significant. Twentymile Coal Company realized that they required a safer, more reliable and more efficient machine to handle and set CANs, and looked for a partner to develop a new design-specific machine. They worked jointly with J.H. Fletcher® engineering and sales to design and manufacture a machine specifically made for setting CANs. The objective was to produce a machine that would handle the conditions and methods that the mine required for setting CANs during longwall retreat. The resulting design had to be safe, stable, have a wide range of motion, be ergonomic, simple to use, and easy to maintain. The machine also had to improve efficiency. The resulting machine has been operating for approximately one year at Twentymile Coal and has been proven to improve safety, reliability, and efficiency. In conclusion, with the task-specific CAN Manipulator, the mine is able to better plan daily tasks with the knowledge that the machine will be available throughout a shift, and the employees will be safer because of the machine?s ergonomics, stability and safety. This has resulted in better productivity and a safer environment.

Jan 1, 2013

By H. B. Lumsden

This paper is intended to deal merely with the commercial development of some of the principal non-metallic mineral resources in the three prairie provinces- Manitoba, Saskatchewan, and Alberta. Coal is not included in this summary. Building Stone First and foremost, mention may be made of the building stone now being produced at Tyndall, Manitoba. This is a mottled limestone and is declared by experts to be one of the finest building stones in America, both as regards durability and appearance. It has been used very extensively both for exterior and interior work, not only in western Canada, but also in the principal cities as far east as Montreal. The stone is the "'Upper Mottled Limestone", which forms the summit of the Trenton (Ordovician) strata in the Lake Winnipeg basin. Quarries are at present being operated at Garson and Tyndall . The area where this stone is known to be available extends in a north and south direction for a distance of three miles, and the main productive ridge is probably about one half mile wide. The outlook for the future of the industry is extremely promising, as the stone is becoming increasingly popular in Eastern Canada, more particularly for interior work.

Jan 1, 1928

By A Lechner, T Baumgartl, S Arnold, P Audet

When revegetation is a part of a rehabilitation strategy at mine sites in arid and semi-arid environments, its success can be strongly affected by the availability of water prior or during the time of seed dormancy, germination and early growth of seedlings. The semi-arid and arid environments of northern Australia are characterised by highly variable and erratic rainfall and hence the actual weather conditions at and around the time of germination and seedling emergence play a critical role in determining the success of plant establishment and the type of plant community that may develop.Using available climate data, an analysis has been undertaken and a set of indices has been developed which describe the suitability of the climatic conditions for rehabilitation. In total, eight sites from Queensland and one site from New South Wales, Australia have been analysed. It could be determined that regular rainfall and relatively short periods of water-deficit are key characteristics of climate suitability. A comparison of the locations studied allowed the separation into suitable and susceptible locations in terms of the availability of water, amount of rain and duration of drought between rain events.In our experience, specific estimates of climate suitability are rarely incorporated into the design of mined land rehabilitation programs. We consider that the regional intensity, seasonality and extremity of climate represent an overarching component of landscape complexity, which in turn will influence the development of post-disturbance ecosystems in these regions. This paper presents the outcome of climate analyses paired with the development of suitability indices. A conceptual framework is presented explaining the suitability matrix and its incorporation as a prognosis tool to achieve greater certainty for success in rehabilitation development.CITATION:Baumgartl, T, Arnold, S, Audet, P and Lechner, A, 2014. Development of climate-based suitability indices for the improvement of success in rehabilitation, in Proceedings Life-of-Mine 2014 , pp 483–490 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By M. A. Bussell, G. S. Camm

The study included lode zones at Wheal Pendarves, South Crofty and Rosevale tin mines. Fluid inclusion-containing microfractures are a common feature of the granites and typically show a preferred orientation over quite a large area. The close proximity of a dominant vein or fault controls their density and orientation. They are important pathways for fluids and provide a marker for palaeo-fluid flow. Overprinting provides a reliable representation of the evolution of the hydrothermal fluids in a vein system from early magmatic fluids to late-stage meteoric and basinal brine input. Measurement of microfracture orientation allows estimation of the regional stress regime during a specific hydrothermal event. Since micro- and macro-structures can generally be reliably correlated, these studies assist in modelling the detailed development of complex vein systems. Microfracture density is a good measure of palaeo-permeability, with implications for control of wallrock alteration. The determination of the location and density of microfractures can assist the mine geologist in identifying the location of potentially economic vein structures where macroscopic markers are absent

Aug 1, 1996

By B. Voyzelle

The deterioration of highway and bridge infrastructure has received considerable attention in recent years because of the billions of dollars needed for repair and rehabilitation. A major factor contributing to this problem is the corrosion of steel reinforcement. Reinforcing steels with good corrosion resistance and relatively low price are therefore essential for maintenance, cost reduction and service-life extension of the steel-reinforced structures. This article describes the development of low-alloying steels that offers good corrosion resistance with reasonably low cost. Topics include steel microstructures, mechanical properties, corrosion performance, industrial applications and economic aspects.

Jan 1, 2005

By J. D. Law

The presence of long-lived radionuclides presents a challenge to the management of radioactive wastes. Separation of the radionuclides from the waste solutions has the potential of significantly decreasing the costs associated with the immobilization and disposal of the waste by minimizing waste volumes. Several solvent extraction processes have been developed at the Idaho National Engineering and Environmental Laboratory for the separation of transuranic elements (TRUs), 90 Sr, and/or 137 Cs from acidic radioactive waste solutions. The TRUEX and POR processes for the separation of TRUs, the SREX process for the separation of 90Sr, the cobalt dicarbollide process for the separation of 137Cs and and a universal solvent extraction process for the simultaneous separation of TRUs, 90Sr, and 137Cs have all been developed in centrifugal contactors using actual liquid radioactive waste solutions and simulated dissolved calcine waste solution. In addition, the behavior of metals with each of the solvent extraction processes was evaluated. This article summarizes the most recent results of the each of the flowsheet demonstrations and provides Information on the centrifugal contactor equipment used for the testing.

Jan 1, 1999

By V. A. Zhilina, I. V. Shadrunova, O. E. Gorlova

"The aim of the study is to develop and scientifically justify a new adaptive approach to the separating processes of deep and complex processing technogenic mineral raw materials. Technogenic mineral resources as a waste of mining and processing industry are mostly complex objects that have specific features of material composition and technological properties and make it processing ineffective with traditional schemes of mineral raw materials enrichment. Mineral wastes are regarded in this study as a complex object with a large number of signs in conditions of uncertain environment and object. However, adaptation is regarded as the process management system’ adaptation to the specific the properties of the object and the environment that has several hierarchical levels corresponding to different stages in the management of complex object. An adaptive approach is considered as a methodological basis of multivariate schemes for opening the mineral resources and creating mechanisms that could transfer these potential technogenic resources to the actual that significantly expand the mineral resource base of the country's black, coloured, rare, noble metals and construction materials. In this case, potentially the solution to the most pressing social and environmental problems associated with the adverse effects of past economic activity simultaneously with the commercial objectives. This approach to the wastes mining and related processing manufacturers meets the core idea of sustainable development as the balance of interests of State, society, business, private enterprise and each person in the areas of rational use of resources, economic efficiency and environmental safety. On the example of metal-containing raw materials in the form of slags of ferrous and nonferrous metallurgy, ferrous metallurgy sludge, mature fine tailings, the application of adaptive approach illustrates to the development of technologies of its deep and complex processing as phased, thoughtful movement from a comprehensive study of technogenic raw materials to build optimal topologies of technological schemes for processing the mineral wastes. INTRODUCTION Involving the Russian economy in the system of global economic relations significantly changes the nature of the country's competitiveness in the development of the world market and urgently requires competent management of its own natural and mineral resources. The latter at the present time in real economic processes cease to be a passive material foundation and become the producing basis in the production processes in the status of so-called natural capital. Introduced in the field of economic theory at the end of the 20th century, this term means both the flow of natural services and real natural resources. Consequently, natural objects, which act as natural resources of a certain production, today must necessarily be evaluated in a strategic sense. Modern standards of sustainable development presuppose that the economy should equally be oriented to balance the interests of the state, society, business, individual enterprise and each person in the spheres of rational use of resources, preservation of healthy ecosystems, ensuring well-being, high quality of life and environmental safety of not only the current generation, but also respect for the rights of future generations, that is, intergenerational equality. Most types of minerals are classified as non-renewable resources, therefore resource-saving in the sphere of mineral and raw materials complexes is one of the most important factors-indicators characterizing the degree of approximation to the model of rational subsoil use, and, consequently, sustainable development (State Report, 2017)."

Jan 1, 2018

Future depth and production limitations of an ore hoisting system are fixed by its initial design criteria. There is little scope to extend these limitations once installation is completed. Depth and production rate upgrades from the initial duty to the hoistÆs practical limitations require capital expenditure in stages, each of which can be defined when assessing the initial system design criteria. A means of presenting and assessing the design criteria, the limiting factors in each option and the relative present and future capital costs is necessary to arrive at a solution that delivers the best value to the mine. Application of this technique to recent friction winder installations and upgrades in the Australian mining industry is of particular interest; however, the analysis methods are also applicable to drum hoists. It is usual to specify a minimum hoisting capacity and depth, based on mine ore handling design and production needs. The final hoist depth and production rate are usually a result of the initial hoist design and hence it is useful from the outset to specify a required production versus depth envelope for the mine. Technical solutions can then be modelled within this envelope at their initial and final duties and a comparative analysis made against the cost of installing and progressively upgrading each solution. Understanding the factors that constrain each solution to a maximum production rate at a given depth is important, as the costs of overcoming limiting parameters such as rope tread pressure and motor power can be significant. The task of understanding and evaluating the options open to the hoisting system designer is simplified using this approach. Communicating the results of a multi-dimensional problem such as hoist specification is also made easier using the graphical methods inherent in the analysis.

Jan 1, 2005

By Reginals W. Burroughs

Diatomaceous or infusorial earth, also called diatomite; fossil meal, or kieselguhr, is derived from the lowest form of vegetable life, the unicellular alga:. It consists of the siliceous remains of extremely minute aquatic plants, which exist in both salt and fresh water. Light i~ a prerequisite to their development. These very small particles secrete silica in much the same way that molluscs secrete lime to form their shells. The diatoms at death sink to the bottom of the body of water in which they lived, and the organic matter gradually decays and is washed away, leaving the skeletons. Thousands of years are required by this means to develop bed5 of sufficient thickness to be of commercial value. The siliceous remains vary in size according to the species, but all are very minute and, as a general rule, they can be identified only under a high-power microscope. Over one thousand types have been distinguished and named. They are all composed of a hydrous or opalescent form of silica, with silica content ranging from seventy to ninety-five per cent. Magnified, they present an attractive sight, a very fragile structure with many interstitial openings known as cells. Many of them consist of two parts, defined as valves, held together by means of a girdle. Certain species, belonging to the Pinnularia family appear as a long comb, in half longitudinal section. The spaces between the teeth are the cells. This particular genus is very common in Nova Scotian deposits.

Jan 1, 1928

By K. A. Lewandowski

The efficiency of heap leaching is reduced by poor solution flow characteristics (i.e., channeling and ponding) that result from fines migration. Agglomeration of the ore can immobilize fines, but for agglomeration to be successful in copper leaching, an acid-resistant binder is needed to stabilize the agglomerates. Until now, there has not been a satisfactory method to evaluate whether a binder was effective, other than squeezing a handful to see if it ?feels right.? This paper reports on several procedures that have been developed to quantitatively determine whether a binder gives good performance in an acidic solution. These procedures have been used to identify binders that would be suitable for copper heap leaching.

Jan 1, 2008

By R. S. Archer

IN the microscopic examination of aircraft-engine parts made of heat-treated alloy steels, the writer has been forcibly impressed by the failure of the usual etching processes to disclose any but gross defects in heat treatment. It seemed particularly desirable to bring out the grain size of the steel, which is indicated in the ordinary etching processes chiefly by the change in orientation of structure from grain to grain. After various attempts, a fairly successful method has been found, which is here presented in the hope that it may be of use to those who have occasion to examine these steels in the heat-treated condition. The specimens worked with have been mostly chrome-nickel steels heat treated (that is, hardened and tempered) to a Brinell hardness of around 300. A few experiments with other specimens will be referred to later. Briefly, the method employed consists in etching the steel about 10 min. in a fresh solution of picric acid in ethyl alcohol, and then rubbing off the smudge of carbonaceous matter on moist broadcloth. Different samples of almost identical analysis; heat treatment, and physical properties (including resistance to impact) respond quite differently to this treatment. In some, the grain boundaries are developed quite readily, while iii others, especially ill those whose grain is unusually fine or in which the final hardening heat, has not quite obliterated the previous crystallization, the results are more obscure. The exact time of etching to secure the best results also differs for various samples, and the greatest success is usually attained by a process of "tinkering." Such a process is illustrated in a series of micrographs, the first six of which were taken at a magnification of 300 diameters.

Jan 1, 1919

By D. M. Baird

"Enormous deposits of gypsum of exceptionally high grade are readily accessible in southwestern Newfoundland. Coming large-scale production from one of these is resulting in renewed interest in deposits which have been known for more than a hundred and twenty years. General stratigraphy and structure of the Carboniferous rocks in which the gypsum occurs are de-scribed. The stratigraphic position of the basal gypsum-anhydrite zone is described. This massive evaporite horizon, which reaches a thickness of about 1,0001 feet, appears at Fishels-Heatherton, where it is largely undeveloped, and again on the nose of an anticline east of Flat bay, where a present production of 20,000 to 40,000 tons per annum is soon to be expanded to make it one of Canada's major producers. Detailed descriptions are given of the several types of gypsum, the relation of the gypsum and anhydrite, and the distribution of sodium chloride in the evaporite beds, and the bearing of all these on the origin of the gypsum are discussed. Brief reference is made to relation to world markets, mining and transportation, grade, and reserves."

Jan 1, 1959

By J. Baz-Dresch

A custom-designed shotcrete system, consisting of an 8-m3 (10-cu-yd) transit mixer and a shotcrete spray boon carrier, is used by a two-man crew to transport and place up to 25 m3 (32 cu-yd) of steel fiber reinforced, dry, silica fume shotcrete per 11-hour shift. Shotcrete is custom blended by a local supplier and delivered predampened. Mix design and quality control are performed with a computer program that develops and graphs a properly balanced mix based upon the materials sieve analyses.

Jan 1, 1992

By Andrea Pezza

The steel market is experiencing a difficult conjuncture: on the one hand steel producers minimize their investments while optimizing their over- production, on the other hand suppliers reduce their internal human resources and capacity in order to overcome the instability of the new era. A return to the steel production levels of the past is not expected in the short term. Research, development and plant concept optimization is one recipe to drive the future of the steel business. This article describes a new concept for a VOD plant developed as a result of thorough investigation and assessment of all possible solutions. A joint and tight cooperation with the final customer was necessary to reaching important results. This article consists of the contributions from the plant suppliers in terms of their experience and feedback, as well as the final user’s. The final customer, voestalpine Giesserei Linz GmbH, and the plant supplier, Primetals Technologies, are both worldwide players and highly focused on reaching best quality and innovation.

Oct 30, 2017

By C. I. Garcia, G. Zhou, W. Gao, A. J. DeArdo

The development of X-100 and X-120 linepipe steels was investigated using a series of low-carbon Mo-Nb-B steels. The laboratory steels were vacuum melted and processed using advanced thermomechanical processing (TMP) philosophies. Prior to the laboratory hot-rolling experiments, the grain coarsening temperature, the conventional T95 and T5 start-stop recrystallization temperatures and the transformation behavior of y were studied using a computer-controlled high temperature deformation MTS-458 and a Theta-IV High Speed dilatometer systems. The results from these experiments provided the guidelines for the design of the laboratory hot-rolling TMP processing experiments. The mechanical properties of the experimental steels showed yield strengths in the range 700-850 MPa and CVN impact properties of over 80 J at -20°C. The best balance of mechanical properties was obtained by using CCR+DQ+Tempering treatments. The major microstructural features responsible for the observed mechanical properties in order of importance were: a) substructural refinement associated with lower bainite, b) dislocation strengthening, c) fine recrystallized ferrite, and d) small amounts of retained austenite. Fine Nb(C,N) precipitates formed in ferrite were observed, however their contribution to the strength was minimum. Most of the Nb(C,N) precipitation took place in austenite. This precipitation was used to exert microstructural control of austenite during hot rolling. The physical metallurgy and optimum TMP to achieve the mechanical properties are detailed in this paper.

Jan 1, 2005

By Robert H. Richards

(Pittsburg Meeting, March, 1910.) THIS is in part a review paper, indicating the various steps that have been taken in developing hindered-settling apparatus, some of the standard data that have been obtained, and some of the conclusions one is led to as to the effect of it in improving concentrating-methods and machinery, and in part it brings in some unpublished work. CAUSES OF LOSS IN ORE-CONCENTRATION. In making a study of the separation of valuable minerals from the waste gangue, particularly by water concentrators, it is necessary to define, first of all, what are the causes of-loss that are likely to interfere with the concentration. Having made this definition; we can then study to see in what way the machines make their losses, and plan remedies for them in an intelligent way. Losses may be stated to occur as included grains, as flat or long grains, as fine free mineral, and as absolute slime. We will take, these up one by one, as follows: Included Grains.-Fig. 1 shows by a set of diagrams how included grains may occur: first, where the heavy mineral grains attached to the quartz are of large size; secondly, where they are of small size ; and thirdly, where very fine particles of heavy mineral are included in the quartz. We have to decide in regard to included grains whether they are rich enough to go direct to, the furnace, or poor enough to throw away, or whether they lie between these two points and require recrushing as the only means of severing the values from the waste. This last case is the only one requiring special treatment at our hands. We will therefore consider that next. * By mutual consent, this paper has been presented also before the Colorado Scientific Society, and the Canadian Mining Institute, Montreal.

Feb 1, 1911

By V. Sheikhzadeh, M. Saghaeian, R. Hejazi, P. Ghobadi

Design and selection of equipment for a grinding circuit strongly depends on the mill function, ore properties and requirements of the down-stream circuit. Primary mills usually work in open circuit and size distribution of product would be controlled in the final steps using a classifier like cyclone. Although HPGRs are mostly utilized as pre-grinding mills, it is preferred to utilize them in a closed circuit due to their specific mechanism of comminution. Unique mechanical design of HPGR and its completely different crushing process than tumbling mills needs precise consideration on its circuit design. In this paper, we investigate the impact of different parameters on design of pre-grinding HPGR circuit and selection of the proper classifier. Our study focuses on iron ore properties (e.g. moisture, particle size distribution of feed and product, compatibility and de-agglomerability). We also investigated various options of HPGR circuit according the classifier efficiency and influences on down-stream processes. The optimum operating parameters of HPGR (working pressure, speed and level of hopper) for the selected circuit were also determined based on pilot and industrial data. Our pilot and industrial tests and observations revealed that HPGR should be arranged in closed circuit because of the edge effect, as a negative factor of non-uniform distribution of pressure force along the roller width and presence of non-crushed particles in the mill product. Wet vibratory screen could be the optimum option for screening of its discharge. Fine part of the wet screen discharge could be delivered to the concentration stage without over-grinding in ball mill using a hydrocyclone working in a reverse closed circuit mode. Moreover, our pilot and industrial tests during design and operation of ten HPGRs in various iron ore processing plants proved that higher pressure and lower roller speed in a fixed level of material inside the hopper could give the desired product size distribution.

Jan 1, 2016

By V. V. Musaev, A. M. Klyushnikov, R. R. Galimov

"A study was made of chemical and material compositions of the oxidized gold-bearing ore of the Kochkovskoe deposit. It was demonstrated that examined ore consisted mainly of quartz, carbonate and feldspar with a gold content of 2.2 g/t and a silver content of 6.1 g/t. By means of agitation leaching tests it was founded that about 79-80 % of gold can be extracted from ore using cyanide leaching solutions. The achieved high-speed dissolution rate of gold was due to its presence in a finely dispersed state (less than 2.73 µm), which was confirmed by the research of Uralmekhanobr. It was proposed that the ore can be processed by heap leaching process using cyanide leach solutions. Technological studies on the modeling of the heap leaching process were initially carried out in percolators with a capacity of 5 kg on agglomerated ore. It was preliminary established that agglomeration should be carried out at a cement consumption of 12-16 kg/t, with the moisture content in pellets reaching up to 10-12 %. The best percolation leaching results can be obtained with ore crushed to the size of -20 mm. The maximum extraction of gold to the solution was 79-80 % while the L:S ratio reached 1.2-1.4:1.In cooperation with the research center of OJSC ""Berezovsky mine"" a semi-industrial heap leaching test was accomplished. The result of a test performed was an extraction of 78.5 % of Au and 21 % of Ag from ore to a pregnant solution. This extraction degree was achieved at a L:S ratio 0.9: 1. On the ground of results obtained, a technical regulation was developed for design of the heap leaching plant with the capacity of 500 thousand tons of ore per year.INTRODUCTION The ore of the Kochkovskoe deposit represents an important reserve of gold in the Zabaikal region. Of the upmost interest are oxidized ores, the processing of which can be carried out by heap leaching (HL) with cyanide solutions. The purpose of this work was to study the composition and to develop a technology for heap leaching of oxidized ore."

Jan 1, 2018