Search Documents

By Elisiane Maria Berton

Neste trabalho propõe-se o estudo do efeito do processo de SHTPN (Tratamento térmico de solubilização após nitretação por plasma), e do tratamento térmico de têmpera e revenido sobre a microestrutura, dureza e resistência à corrosão do aço inoxidável ferrítico AISI 409. Por meio do SHTPN obteve-se uma camada martensítica de nitrogênio na superfície do aço. Após o SHTPN as amostras foram temperadas de 950°C e revenidas nas temperaturas de 200, 400 e 600°C. A resistência à corrosão foi avaliada por meio da técnica de polarização cíclica e a dureza através de ensaios Vickers. Verificou-se que o SHTPN afetou significativamente a dureza do aço e o tratamento de têmpera refinou e melhorou a distribuição da martensita de nitrogênio. A camada martensítica formada apresentou espessura da ordem de 660 ?m. Os resultados indicam que é possível obter uma camada martensítica com dureza de 620 HV e aumento da região passiva, bem como do potencial de nucleação de pite quando comparado à condição não tratada (ferrítico). O melhor resultado de corrosão foi obtido para a amostra revenida na temperatura de 200°C.

Aug 8, 2018

By Marcos Felipe Macêdo Cardoso

Com o aumento dos investimentos energéticos na região amazônica, surge a necessidade de recapacitação das linhas de transmissão existentes, a fim de mitigar as interrupções de fornecimento de energia para os grandes centros urbanos. Dentro deste contexto, as ligas termorresistentes possuem alta capacidade de transmissão de eletricidade, propondo-se avaliar a influência do tratamento térmico sobre as propriedades da liga Al-0,05%Cu-[0,35-0,45]%Fe modificada pelo teor de 0,15%Zr. Os lingotes foram obtidos por fundição direta em coquilha metálica, usinados e envelhecidos artificialmente por 04 (quatro) horas a 150ºC e comparado seus resultados para a mesma liga sem tratamento. A influência do tratamento térmico foi avaliada através da caracterização macroestrutural, elétrica (ensaio de resistividade) e mecânica (ensaio de tração). Foi selecionado o diâmetro que apresentou os melhores resultados nos ensaios, para realização dos testes de termorresistividade, segundo o Protocolo COPEL e a Norma ASTM B941-10. O tratamento térmico provocou ligeiro aumento nos valores de condutividade elétrica e limite de resistência à tração (LRT), sem alteração da macroestrutura. Como destaque, o diâmetro 3,0 mm apresentou os melhores resultados de LRT e condutividade, cujos fios foram caracterizados como termorresistentes com e sem tratamento térmico segundo o Protocolo Copel, e somente os fios com tratamento térmico segundo a norma ASTM B941-10.

Oct 30, 2017

By Pedro Henrique Teshima Shioga

Quando processos de engenharia de superfícies multifuncionais que combinam fases de propósito orientadas são aplicados a substratos moles, uma combinação de alta resistência ao desgaste, suporte de alta carga e baixos coeficientes de atrito podem ser obtidos. Neste estudo, os efeitos de diferentes camadas nitretadas no comportamento tribológico de revestimento Diamond-Like-Carbon (DLC) depositado sobre aço SAE 1040 são investigados. A nitretação foi conduzida sob diferentes temperaturas e misturas de gases para criar três camadas de nitretos distintas: duas camadas de compostos com predominância de fases e e ?’ e uma camada de difusão. Todas as superfícies foram então revestidas com DLC, depositado via Plasma-Enhanced-Chemical-Vapour-Deposition (PACVD). As fases de nitreto foram analisadas utilizando difração de raios-X e a topografia da superfície foi analisada por interferometria de luz branca e microscopia eletrônica de varredura. O comportamento tribológico foi investigado utilizando esfera e plano com movimento alternado com carregamento incremental até a falha do filme DLC. Os testes tribológicos indicaram que o melhor desempenho foi alcançado por uma específica combinação de dureza, rugosidade superficial e tipo de nitreto. A melhor capacidade de mancalização entre o revestimento DLC e o substrato mole foi alcançada quando a camada de nitretos constitui-se apenas de uma camada de difusão.

Aug 16, 2017

By Eduardo R. Rodrigues, Ankur Narang, Roberto Federico Ausas, U. T. Mello, Jose Maria Segura Serra, M. R. Lakshmikantha, Ignacio Carol, Kamal C. Das

"Modeling of big faults or weak planes of strong and weak discontinuities is of major importance to assess the Geomechanical behaviour of mining/civil tunnel, reservoirs etc. For modelling fractures in Geomechanics, prior art has been limited to Interface Elements which suffer from numerical instability and where faults are required to be aligned with element edges. In this paper, we consider comparative study on finite elements for capturing strong discontinuities by means of elemental (EFEM) and nodal enrichments (XFEM) for Geomechanical applications. For general fracture scenarios, Oliver et al. (2008) have demonstrated advantages of EFEM over XFEM for including: (a) ease of modeling in any standard finite element code due to the possibility of static condensation, (b) higher accuracy in some cases for coarse meshes, and, (c) a reduced computational cost. However, there has been no work that considers cohesive fractures in Geomechanics. We present a numerical analysis based on a linear constitutive model and linear triangular elements for the bulk and a linear constitutive behaviour for the fault for a representative set of fault planes in a circular tunnel made in rock mass. In the numerical examples we consider both well-traced and bad-traced meshes. We focus on traction profile analysis for both EFEM and XFEM, since that is crucial to understand the cohesive fracture behaviour specially rock joint. Therefore in each case, shear, normal and stress ratio are compared across the two methods along the fault plane. This is the first such work that compares XFEM and EFEM behaviour for Geomechanics problems.For the considered class of problems and the sharp penalization approach without regularizations adopted, it can be observed that accuracy and robustness of EFEM may strongly depend on the fault orientation with respect to the element edges, while, XFEM is independent of fault alignment with element edges. It has been also observed that, with mesh refinement model, stress oscillation completely removed with XFEM however EFEM fails to provide oscillation free results with finer mesh in case bad-traced model. We also performed error analysis and found that in case of bad-traced mesh the average error in the XFEM is 84% smaller than of EFEM and for XFEM the error goes to zero with increasing mesh resolution, while for EFEM the error increases with mesh resolution. Thus, we experimentally demonstrate that, XFEM performs better than EFEM in terms of accuracy and rate of convergence with marginal increase in computational cost. This work hence provides novel insights on the application of XFEM and EFEM in Geomechanics."

Jan 1, 2015

By EFFC/DFI Concrete Task Group

Concrete technology continues to advance rapidly and modern mixes with five components – cement, additions, aggregates, (chemical) admixtures and water – often have characteristics which differ significantly from the older three component mixes – cement, aggregates and water. Recent trends have favoured higher strength classes and lower water/cement ratios, resulting in greater dependence on admixtures to compensate for reduced workability and to meet the (often competing) demands for workability in the fresh state and setting time. The application of testing methods which reflect the true rheological properties of the concrete has not developed at the same rate as the mixes themselves and it is still not uncommon for the slump or flow table test to be used as the only acceptance test for fresh concrete.A joint review of problems in bored piles (drilled shafts) and diaphragm walls cast using tremie methods by both the European Federation of Foundation Contractors (EFFC) and the Deep Foundations Institute in the United States (DFI) identified a common issue. The review determined that many of the problems were caused by (or in part due to) the use of inadequate concrete mixes with inadequate workability, or insufficient stability or robustness of the mixes. It further identified the primary causes as inadequate concrete specifications and inadequate testing procedures. The consequences of these problems are often significant and it has been recognised that spending more time and money on getting the concrete right is the most cost effective approach.A joint Concrete Task Group was set up by EFFC and DFI in 2014 to look at this issue and this guide is the output from that Task Group. A research and development project, funded by the Sponsors of this guide, is being carried out by the Technical University of Munich in conjunction with the Missouri University of Science and Technology. This project includes desk studies, laboratory testing, and onsite testing at worksites in Europe and the US. The research work will be completed during 2016.

Jan 1, 2016

By G. Zeng

Although the solubility of oxygen in zinc electrolyte is less than 9 mg/L, the effect on deposit stability and zinc-dust consumption can be significant. Sodium sulfite is used to deoxygenate the electrolyte. The effect of the sodium-sulfite concentration on cobalt removal is investigated. The results show the reduction of sulfite to elemental sulfur that adhered to the zinc dust surface forming a passivating layer, and small amounts of sodium sulfite have no effect on cobalt removal. The optimum amount of sodium sulfite is 100 mg/L. It is an important consideration in purification circuits to use sodium sulfite as an additive to cobalt cementation.

Jan 1, 2005

By Carle Hayward

IN reheating quenched steel to remove part of the hardness, the softening effect has generally been considered to be a function of temperature and time. The temperature effect is well known, and long before pyrometers were heard of the blacksmith was able to do a good job of tempering, by rule-of-thumb methods and experience in judging temperatures. Modern conditions, which demand steel that will withstand the severest tests, require that the heat treatment he carried out with every possible precaution to secure the best results obtainable. Pyrometers and heat-treatment furnaces of many types are on the market and improvements are continually being made so that it is now possible to regulate the temperature in heat treatment very accurately. There is -still a question regarding the time that the steel should be subjected to treatment. It is customary with all operators to insure the desired tem-pressure throughout the specimen and it is generally supposed that a longer treatment of a hardened steel produces a further softening but there are few published figures showing the exact effect of time of treat-ment at constant temperature. A search of the literature disclosed several brief statements that the tempering effect was a function of both time and temperature, but in no case were any figures given. The opinion is very generally held that the well-known tempering colors are accurate indicators of the degree of tempering. This is disputed by Brearley (The Heat Treatment of Tool Steel, page 102) who states: It has been said that the result would be the same in respect to both hardness and other properties whether the colors were obtained by a shorter heating at a higher temperature or a longer heating at a lower one. This, to say the least, is a very doubtful conclusion, and is certainly not borne out by mechanical tests on oil-hardened and tempered motor car steels, which, after tempering for periods varying from 15 min to 2 hr., show no very great differences. The present investigation had for its object the obtaining of some definite data regarding the effect of time, which might serve as a guide to those engaged in the heat treatment of steel. The Rhode Island Tool Co. cooperated by furnishing the steel and machining the test specimens.

Jan 2, 1917

By O A. Aladejebi, S Mitra, T Singh, D O’Dea, S, T Honey

Granulation of the iron ore blend and the additives is the foremost step in the agglomeration of iron ore fines to achieve a permeable bed during sintering, which is crucial for sinter productivity. This study investigated the granulation of four types of blends to determine the impact of granulation on bed permeability. The blends were granulated in a rotating drum at various moisture contents and their JPU permeability was measured at each moisture content in a permeability pot (diameter 95 mm and height 500 mm) at various flow rates. Several independent experiments were carried out to investigate the changes in permeability when mixtures of different particle size range (-1 mm and +1 mm) were introduced into a packed bed with a larger particle size range (-6.3 mm to +4.0 mm). The results revealed that the addition of particles in the -1 mm size range had a more pronounced negative impact on permeability compared to particles in the +1 mm size range. This can be attributed to the relatively higher energy losses (mainly inertial) associated with the presence of -1 mm particles in the mixture. The findings were used to quantify the granulation process based on the -1 mm particle size fraction in the granulated mix and their utilisation (denoted by UI-1 mm). For achieving optimal permeability in a specific blend, it was found that a UI-1 mm (utility index of -1 mm particle size) ranging from 0.82 to 0.92 was required. However, exceeding a UI-1 mm value of 0.95 resulted in weaker granules prone to deformation and led to decreased bed permeability. The study also showed that the UI-1 mm was highly dependent on the water addition per kg of -1 mm in dry feed and suggested adding ~80 to 110 mL of water per kg of -1 mm in dry feed to attain the best possible permeability. Additionally, the research proposed a mechanism involving the melting of granules at high temperatures and highlighted the influence of -1 mm particles on bed permeability during the sintering process.

Sep 18, 2023

By K. Sasaki, Y. Oriia, Shigeto Kuroiwa, H. Miki, Yuji Aoki, T. Hirajima, G. P. W. Suyantara

The effect of a sulfite reagent on the floatability of chalcopyrite and enargite was investigated in this paper. The flotation tests using single and mixed minerals were performed under various concentrations of sulfite. The flotation tests using a single mineral showed that the sulfite reagent depressed the natural floatability of both minerals at pH 9. Surprisingly, enargite was floated after the addition of potassium amyl xanthate (PAX) following the sulfite treatment, and the floatability of chalcopyrite depressed under a similar condition. X-ray photoelectron spectroscopy analysis results showed that the sulfate species increased after the sulfite treatment on both minerals. However, the addition of PAX removed this sulfate species and rendered the enargite surface hydrophobic. This phenomenon was not observed on the chalcopyrite surface. FTIR analysis and PAX adsorption studies were performed to support this finding. The flotation of a mixed mineral was in agreement with the flotation of a single mineral, indicating a possibility for selective flotation of chalcopyrite and enargite using the proposed method. Keywords: Flotation, chalcopyrite, enargite, sulfite, potassium amyl xanthate

Jan 1, 2020

By Brahm Prakash, R. Schuhmann

Chemical conditions for flotation and nonflotation of cassiterite and fluorite with oleic acid as collector and with alizarin dyes as modifying agents were studied by means of small-scale, vacuum-flotation tests. Artificial cassiterite was prepared for these tests by high-temperature methods, especially by crystallization from borax melts.

Jan 1, 1950

By Narasimhan K. S, Sastri S. R

A typical high silica low grade magnesite from the Salem area of Southern India, was used in studies to develop a suitable flotation system involving commercially inexpensive sodium oleate as the collector together with other reagents which can give a product of the required grade with an acceptable recovery. It was found that the presence of metallic ions such as Cu+, Fe+++ or Ca++ introduced by the addition of their salts, or by their formation with the addition of hydrochloric acid to react with magnesium and calcium carbonate in the me, can act as effective depressants for silica. The addition of 'hydrochloric acid' was found to give best results.

Jan 1, 1980

By Yuzura Sato

Viscosity has been measured for various molten binary alloys of nickel with iron, cobalt and chromium in order to clarify the behavior of viscous flow of molten nickel alloys. The entire concentration range for iron and cobalt and 0-67at% of chromium content were studied. The measurement method was an oscillating cup viscometry using an alumina crucible that was precisely machined. The temperature was up to about I 880K for all the measurements. The results represented good Arrhenian relationship although some measurements included overcooled temperatures. The isothermal viscosities increased monotonously with an addition of iron and chromium into nickel. The addition of cobalt increased after stationariness. The isothermal viscosities showed concave curves. Activation energies increased monotonously by adding all the elements into nickel. These phenomena were considered to be related to the thermodynamic properties 'such as the heat of mixing and the structures of mixture melts.

Jan 1, 2003

By Yuzuru Sato

Viscosity has been measured for various molten binary alloys of nickel with iron, cobalt and chromium in order to clarify the behavior of viscous flow of molten nickel alloys. The entire concentration range for iron and cobalt and 0-67at% of chromium content were studied. The measurement method was an oscillating cup viscometry using an alumina crucible that was precisely machined. The temperature was up to about 1880K for all the measurements. The results represented good Arrhenian relationship although some measurements included overcooled temperatures. The isothermal viscosities increased monotonously with an addition of iron and chromium into nickel. The addition of cobalt increased after stationariness. The isothermal viscosities showed concave curves. Activation energies increased monotonously by adding all the elements into nickel. These phenomena were considered to be related to the thermodynamic properties such as the heat of mixing and the structures of mixture melts.

Jan 1, 2003

By Md. Maniruzzaman

The quenching performance of a liquid quenchant can be controlled by controlling the agitation in the quench tank. Without agitation, a vapor layer or bubbles form at the hot part surface and the natural convention of the quenchant limit the heat extraction rate at the quenched part surface. Resistance to the heat extraction rate can be reduced by breaking the vapor layer or by inducing a turbulent convection at the part surface through agitation (Le. forced circulation of the quenchant). To determine the effects of agitation on the quench performance of a mineral oil based quenchant, the CHTE quench probe system was used with AISI4140 steel probe tip. Quenching performance of the oil is evaluated by computing the effective heat transfer coefficients of the steel probe as a function of surface temperature using Lumped Parameter Analysis. In addition, computational fluid dynamics (CFO) simulation of the quench tank with an impeller type agitator has been done to understand and predict the fluid flow pattern in the tank. CFO simulation also provides insights for determination of optimal location of the impeller and the quench probe tip. Keywords: CHTE Quench Probe, agitation, CFD simulation, liquid quenchant, 4140 steel

Jan 1, 2003

By J Zhang, O Ostrovski, C Zhang D Cai, Q Wang

The conventional CaO-SiO2-based mould fluxes are not suitable for high-Al steel casting because of the strong reaction between silica in the flux and aluminium in the steel strand. In the process of casting of high-Al steel, flux composition changes; with the decrease of the silica concentration and increase of alumina. Knowledge and understanding of the effect of the Al2O3/SiO2 ratio on flux structure and properties are useful for flux design for the high Al-steel continuous casting. This paper investigated the effect of the Al2O3/SiO2 ratio on structure, viscosity, phase composition of fluxes quenched at different temperatures and heat transfer of CaO-Al2O3-SiO2-B2O3-Na2O-Li2OMgO- F fluxes. It was found that flux melting temperature increased with the increase in Al2O3/SiO2 ratio. Viscosity of the flux melts increased significantly with the increase of the Al2O3/SiO2 ratio from 0.7 to 1.2, reaching the maximum value, and then decreased with further increase of the Al2O3/SiO2 ratio. Raman spectroscopy analysis revealed that the change of the Al2O3/SiO2 ratio led to the change of aluminate and silicate structural units. The turning point for viscosity was attributed to the change in the degree of flux polymerisation. X-ray diffraction (XRD) analysis showed that increasing Al2O3/SiO2 ratio increased crystallisation tendency of the fluxes. Heat transfer measurement by infrared emitter technique (IET) revealed that increasing Al2O3/SiO2 ratio led to the decrease in heat flux which is correlated well with the increased crystallinity of the flux. The results suggested that the flux with Al2O3/SiO2 ratio 4.3 is the best candidate among the studied CaO-Al2O3-based mould fluxes for casting of high-Al steel.

Aug 21, 2024

By A Batnasan

The main techniques for removing phosphorus as an impurity element in iron ores are physical separation (eg magnetic separation, flotation) and chemical separation (acid leaching, alkaline leaching and bioleaching) processes. When phosphorus occurs in iron ores as phosphate minerals (eg apatite), physical separation techniques are available to remove the gangue minerals from iron ores. On the other hand, chemical separation techniques are suitable for reducing phosphorus levels when phosphorus is associated with iron oxides and hydroxide minerals (eg hematite and goethite) in iron ores. In this study, the dephosphorisation behaviour of high‐phosphorus iron ore was investigated using a combined alkaline roasting and water washing route. Roasting experiments were conducted in a laboratory electric muffle furnace using various concentrations of sodium hydroxide (0–50 g/kg-ore) at different temperatures (100–800°C), varying prolonged roasting times (0–2 h), and different particle size fractions (-45 – -250 μm) of iron ore. Subsequent water washing experiments were employed at various pulp densities (30–1000 g/L) and different times (30 s – 60 min) at ambient temperature. Hematite and goethite were the main minerals in the high-phosphorus iron ore identified using X-ray diffraction (XRD) analysis. The iron ore assaying 63.40 mass % Fe (total), 0.240 mass % P, 4.53 mass % SiO2, and 4.87 mass % Al2O3 were determined using X-ray fluorescence (XRF) analysis. The results showed that the dephosphorisation rate of the iron ore was reached 40 per cent under roasting with 50 g/kg-ore NaOH at 300°C for 2 hours followed by water washing for 30 s with a pulp density of 300 g/L, reducing phosphorus level from 0.240 mass % to 0.142 mass %. At the same time, the iron grade was reduced from 63.4 per cent to 59.5 per cent, caused by an iron loss. Results suggest that the phase transformation of goethite induces the dephosphorisation of high-phosphorus iron ore under alkaline roasting conditions

Aug 22, 2022

By Shenghua Yin, Xun Chen, Rongfu Yan, Zepeng Yan, Wei Chen

The application of cemented paste backfill (CPB) with alkali-activated slag and phosphogypsum (ASP) can contribute to the sustainable development of the mining industry. The effects of PG content, NaOH content, solid content, and waste rock-rod milling sand (W/R) ratio on workability, unconfined compressive strength (UCS), and setting time of ASP-CPB were investigated in this paper. The results showed that the workability of ASP-CPB decreased with PG content and NaOH content. Compared to OPC-CPB, ASP-CPB exhibited better workability and higher long-term (7 days and 28 days) strength at predetermined backfill formulations and curing times. The mid-term strength of ASP-CPB first increased and then decreased with PG content, while the short-term strength (3 days) decreased gradually due to the influence of soluble acidic impurities. Excessive NaOH will harm the strength of ASP-CPB, possibly due to the swelling effect of the reaction products (ettringite and sulfate). Strength and setting time increased and decreased with solid contents, respectively. Moreover, the compactness of the mixture has an important effect on strength and workability. The workability and strength of ASP-CPB reached the minimum and maximum values at a W/R ratio of 5:5, respectively. Pollutant index detection indicated that most of the pollutants in ASP-CPB leachate met the discharge standard, which proved that ASP-CPB is an effective method to recover PG. The results of the research will provide theoretical guidance for the efficient recovery of PG resources and support the achievement of safe, clean, and efficient mining.

Nov 17, 2023

By A Takahashi, Y Uchisawa, M Hayashi, T Watanabe, M Susa

Owing to the deterioration of iron ore, the Al2O3 concentration in iron ore increases, and thus it is important to investigate the effect of increment in Al2O3 concentration on the microstructures of iron ore sinters. During the sintering process, a melt is present in the sinter for only a few minutes, and therefore the microstructure of the sinter doesn’t reach thermodynamic equilibrium. Nevertheless, the formation process of the microstructures can be interpreted and predicted to some extent from the equilibrium phase diagram. This study investigated the liquidus isotherm in the CaO-SiO2-Fe2O3- 5 mass% Al2O3 system at 1240°C in air and the phase equilibria of silico-ferrite of calcium and aluminium (denoted by SFCA) and SFCA-I by XRD (X-ray diffraction analysis) and electron probe micro analyzer (EPMA). The following results were obtained: 1. The ferrite melt region with a high Fe2O3 concentration shifts to the lower Fe2O3 side than the liquidus isotherm in the CaO-SiO2-Fe2O3 system. 2. The compositional region of SFCA extends in the CaOꞏ3Fe2O3-4CaOꞏ3SiO2 direction than the silico-ferrite of calcium (denoted by SFC) composition region with a 0 mass% Al2O3. 3. SFCA-I is observed in the present system, which suggests that the increment in the Al2O3 concentration contributes to the stability of SFCA-I. These results imply that an increment in Al2O3 concentration in iron ore leads to a decrement in the volume fraction of the bonding phase and that the fraction of the SFCA phase increases, and those of 2CaOꞏSiO2 and slag phases decrease in the bonging phase. The SFCA-I phase is also precipitated from the slag with an Al2O3 concentration around 5 mass%.

Jun 19, 2024

By S. B. Kang

Magnesium has poor ductility at temperatures lower than 225°C and, as a result, Mg alloy sheets are produced via fairly complex thermomechanical processes consisting of numerous sequential steps of hot (warm) rolling with low reduction and intermediate recrystallization annealing operations. In context of the present study, a simple technology for the fabrication of magnesium sheets by hot (warm) rolling was applied to various magnesium alloys. The misch metal addition in those AZ alloys was done to evaluate the deformation behavior. Tensile tests were carried out for those AZ alloys after applying different heat treatments. The precipitation of ß phase (Mg17Al12 phase) induced different microstructures with various cooling method from solution treatment temperature, and also with various annealing treatment temperatures.

Jan 1, 2006

By Michael J. Friedel

The permeability and flow capacity in unsaturated media is investigated by the Bureau of Mines for application to in situ copper leach mining at the Cyprus Casa Grande mine site. Moisture retention properties are derived and combined with scanning electron microprobe data to characterize the mineralogy, texture, pore size, distribution, and permeability of the host rock. Finite element modeling is used to derive a saturated permeability, ambient degree of saturation, and assess various injection-recovery schemes. Recommended design modifications for optimization of solution distribution and maximum recovery from the rock matrix requires either (1) the injection pressures on the order of 1500 psi and recovery wells operating in a suction mode, or (2) performing permeability enhancement, through rubblization. By producing a maximum block diameter of 4 m, injection pressures can be reduced to 500 psi with improved recovery and containment of solutions.

Jan 1, 1991