Search Documents

By J. F. White

An experimental study was undertaken to evaluate the feasibility of a selective chloridizing roasting pre?treatment process for the elimination of impurities from zinc feed?stocks prior to recovering zinc by conventional unit operations. In this investigation, a number of chemistries that might serve as a basis for such a pre? treatment process were examined. A variety of chloridizing agents were admixed with EAF dust to promote the selective removal of lead and cadmium by the formation of volatile metal chlorides, he results of the experimentation firmly establish that selective chloridizing roasting is a technically feasible means of eliminating lead and cadmium from EAF dust. Excellent extraction efficiencies were accomplished with a number of chloride additives; as high as 98 percent lead extraction and 88 percent cadmium extraction were attained with minimal zinc losses, Continuous pilot?scale tests reinforced the trends established by laboratory?scale experimentation, Attempts of chlorine elimination using pyrohydrolysis were less successful. The extent of chlorine elimination was found to be highly dependent upon EAF dust sample type and treatment temperature.

Jan 1, 1996

By Neel Gupta, Brijes Mishra

Coal mining activity disturbs the natural equilibrium of in situ stress state such that the induced stresses deform the surrounding rock mass. Although the installation of roof supports typically prevents rock deformation, rock mass failure may still occur in bolted roof. The erratic failure of rock mass after few days to months and years of excavation is the result of time-dependent deformation of roof rock under constant surrounding stresses. In the current research, the triaxial laboratory creep experiments proved that Marcellus shale exhibits time-dependent deformation under constant stress that was smaller than the failure strength. However, unlike conventional experimental results, the time-dependent deformation did not depend on the level of constant stress. The often-neglected initial state of specimens and intrinsic heterogeneity highly influenced the time-dependent failure of Marcellus shale.

Jul 27, 2021

By Kenneth Gavin, Weichao Li, Paul Doherty

"The lateral load capacity is one of the most important issues to be considered in designing piles to resist berthing loads, ship impact forces and for monopiles used in the offshore wind sector. A number of semi-empirical design approaches are available to calculate the ultimate soil resistance and assumed soil reaction profile along the piles’ embedded depth. In order to investigate the response of monopiles to lateral loading, a series of field experiments were conducted on instrumented steel pipe piles. Two lateral loading tests were performed on model piles with a diameter, D, of 340 mm and embedded depth, Lem, of 2.2 m, giving a Lem/D ratio similar to those adopted in the offshore wind sector. The piles were driven into dense sand at the University College Dublin geotechnical test bed site in Ireland. 10 pairs of strain gauges were installed on each model pile along the embedded depth at 10 levels to capture the load transfer and bending moment within the piles. The deflection and rotation at the model pile head were measured by Linear Variable Differential Transformer (LVDT) and inclinometers. The tests results were used to perform a detailed evaluation of current design methods. In the final section, discussion on the determination of the ultimate lateral load capacity for monopile design was conducted. IntroductionA pile’s lateral load capacity is determined, for design purposes, by two conditions: 1) the ultimate lateral load, Fu, divided by an appropriate safety factor; and 2) the load according to the maximum lateral deflection that the support structures can sustain. In view of the first condition, design methods to calculate the ultimate load were developed for piles used in the offshore oil and gas sectors, which tend to be much more slender than monopiles used in the wind industry. The purpose of this study was to investigate whether these design methods provide reasonable estimates of ultimate capacity, for short rigid monopiles.The methods to determine the ultimate lateral load generally follow three steps: 1) determine the ultimate soil resistance, Pu, along the pile embedded depth; 2) adopt the most appropriate soil reaction profile, Pz, along the piles embedded depth when the pile subjected to the ultimate lateral load condition (four of the most popular ones are depicted in Figure. 1); and 3) ensure equilibrium of lateral forces (see Equation 1, symbols are listed at the end of the paper) acting on the pile and bending moments (see Equation 2) about a point in pile is employed to determine the ultimate lateral load."

Jan 1, 2015

By Frederick Laist

THE object of the construction and operation of the 80-ton leaching plant was to test out the leaching of sand tailings on a large scale and, if possible, determine a definite method of operation, and the best construction for the larger unit which is now being built. It was also of importance to obtain some practical data as regards cost items. The 80-ton plant was not expected to be a commercial success. A leaching process on such low-grade material necessitates the treatment of a very large tonnage.. Such a cost item as labor, for instance, is entirely out of proportion in such a small plant. The amounts of acid, salt, scrap iron, and fuel for roasting, however, are the same per ton in an 80-ton plant as in a 2,000-ton plant. These costs were definitely established. Also the percentages of extraction and grade of tailings were definitely determined for a large-sized unit. Following will be found the description of the plant, the method of operation and the results obtained. A -general view of the plant is given in Fig. 1. The bins consisted of one coal bin with a capacity of 30 tons, one salt bin with a capacity of 20 tons, and a "mill tailings" or feed bin which held 70 tons. The coal and salt bins were placed with their floor level even with the firing floor of the roasting furnace. The feed bin, to give it greater capacity, discharged about 12 ft. below this point, to a 12-in. conveyor belt, which, in turn discharged into a pug mill. This fed another conveyor belt, which discharged into the top hearth of the furnace. The furnace was an ordinary six-hearth MacDougall roaster, .20-ft. in diameter. It was equipped with two fire boxes, on opposite sides, the flames entering on the third hearth. An induced draft was obtained with a Buffalo blower, worked as an exhaust fan. Just above the top hearth was an annular flue around the whole circumference of the furnace. Slots at intervals of about 18 in. led from this flue down into the top hearth. The slots were 2 in. wide by 6 in. long. This annular flue proved rather unsatisfactory, as it tended to fill up with flue dust and choke the slots, thus cutting down the draft. The volume of gas through

Jan 8, 1914

By G. Laird, N. B. Gray, N. Lawson

"Photographic, video, laser, hot film and conductivity methods are used in the experimental study of gas-liquid flows. A discussion of their capabilities and limitations are given in this paper illustrating the wide range of phenomena that can be studied. Most of these methods are limited to physical models at room temperature with transparent fluids, although they can be extended for use with opaque and hot fluids. A number of these techniques have been used by the GKW CRC in studies on industrial plants and their usage is increasing although a number of technical difficulties still need to be overcome. An in-depth discussion of the laser doppler anemometry (LDA) and particle image velocimetry (PIV) methods is given with experimental results on the flow field of an air plume in water based on advanced development of the techniques and studies carried out at the GKW CRC. The LDA method provides high resolution data on the velocity profiles, while the PIV method provides an overall view of the complex flow structure occurring at the gas-liquid regions. These two methods complement each other in providing experimental data for validating numerical models and exploring the complexities of multi phase flows.IntroductionThe injection of gases into melts is an important operation in the metallurgical industry. It is used in converters, anode furnaces, blast furnaces, ladles, bath smelters, zinc fumers and many other smelting processes. In many of these processes, the gas is injected into a molten bath resulting in the formation of bubbles that promote reaction, mixing, alloying and heat transfer. The study of gas-liquid systems presents enormous challenges to the researcher due to the complexity of the mathematical and physical modelling which require innovative numerical and experimental skills."

Jan 1, 1996

By Isaac A. Zlochower, Michael J. Sapko, Eric S. Weiss, Kenneth L. Cashdollar

This paper describes dust explosion research conducted in an experimental mine and in a 20-L laboratory chamber at the Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH). The primary purpose of this research is to improve safety in mining, but the data are also useful to other industries that manufacture, process, or use combustible dusts. Explosion characteristics such as the minimum explosible concentration and the rock dust inerting requirements were measured for various combustible dusts from the mining industries. These dusts included bituminous coats, gilsonite, oil shales, and sulfide ores. The full-scale tests were conducted in the Lake Lynn experimental mine of NIOSH. The mine tests were initiated by a methane-air explosion at the face (closed end) that both entrained and ignited the dust. The laboratory-scale tests were conducted in the 20-L chamber using ignitors of various energies. One purpose of the laboratory and mine comparison is to determine the conditions under which the laboratory tests best simulate the full-scale tests. The results of this research showed relatively good agreement between the laboratory and the large-scale tests in determining explosion limits. Full-scale experiments in the experimental mine were also conducted to evaluate the explosion resistance characteristics of seals that are used to separate non-ventilated, inactive workings from active workings of a mine. Results of these explosion tests show significant increases in explosion overpressure due to added coal dust and indications of pressure piling.

By H. W. Smith, R. D. Fournier

This paper presents the results of an investigation of a full-scale rod mill. Appropriate numerical techniques are developed for the experimental determination of the parameters of a dynamic mathematical model from steady state data. The results confirm that this full-scale rod mill behaves similarly to laboratory-scale ball mills for which results have previously been obtained. It is noted, however, that although the model presented is adequate for predicting over-all particle size distributions, the size distributions of individual components of a multicomponent ore cannot be predicted.

Jan 1, 1972

By G. Viramontes-Gamboa

Approximately 70% of world copper reserves consist of the mineral chalcopyrite, and much international effort has focused on its study. Ultimate objectives include the development of environmentally friendly alternatives to smelting, and technologies to treat low-grade ores, for which concentration and smelting are economically unviable. Unfortunately, chalcopyrite leaching is inefficient in H2S04-Fe2(S04)3-FeS04 solutions, which is considered to be the most desirable oxidizing medium for leaching of copper sulfides, since the chemistry is well known, corrosion of industrial equipment is negligible, subsequent copper recovery by SXlEW is well established, and environmental impact is minimal. The main reason for this inefficiency is the self-passivation of chalcopyrite. We have devoted considerable effort in the understanding of this phenomenon, and have developed a predictive electrochemical methodology capable of establishing a priori the precise range of potentials within which chalcopyrite leaches and where it is passivated. Since potential control is a critical parameter in chalcopyrite leaching, this experimental methodology can be very useful for establishing the best conditions to leach chalcopyrite. In this paper, the scientific foundations of this predictive experimental technique are presented, and its practical application is demonstrated by comparing its predictions with leaching experiments from the literature.

Jan 1, 2007

By WenCai Li, Yong Ren, Shuai Niu, Xin Hong

"Temperature measurement is very important in metal smelting process. Many devices are used to realize non-contact temperature measurements. Compared to conventional thermocouple, infrared temperature measurement has it's unique advantages. However, using an infrared temperature measurement at the top of the furnace can not obtain the desired optical signal because of disturbance from slag layer, high-temperature gases and other effects. A real time thermometry system with dual-wavelength radiation was presented to get optical signal emitted from molten metal through bottom-blowing nozzle. Taking into account the advantages and disadvantages of bottom-blowing devices, a MHP (Multiple Hole Plug) bottom-blowing device was used, through which the optical signal was transferred to the infrared thermometer by use of optical fiber. After conversion and analysis in real-time, the result was displayed and recorded in computer. After calibration, it could be a good predictor of temperature trend in a metallurgical process. IntroductionAt the refining stage of steelmaking, in order to achieve predetermined chemical composition and temperature, high-temperature molten steel is refined in a furnace such as converter. Because the refining process involved with chemical components and reaction velocities in the furnace rely on the temperature of steel, it is necessary to know the temperature accurately in real time during the process. And temperature measurement is also helpful for the end-point judgment. The temperature in the refining process changes quickly, for instance, in a converter, 300t molten steel is processed in only about half an hour.At present, traditional way of temperature measurement is using a thermocouple probe mounted on a lifter called a sub-lance. The thermocouple is immersed in molten steel and its temperature is measured during the short period until the thermocouple is fused. Accurate and reliable temperature can be obtained by this method, but in consideration of the discontinuous measurement and the costs, missing the end-point temperature may sometimes occur.According to the above background, a method in which a temperature-sensing element such as a thermocouple is immersed directly in molten steel is not suitable for the continuous temperature measurement because materials having such stability are not available. Therefore, radiation thermometry is promising. There have been some reports on radiation thermometry through an observation nozzle through the bottom or side of a refining furnace [1, 2]."

Jan 1, 2014

By Jian-hua Ren, Guang-liang Wu

A lot of dust is produced in iron and steel enterprises, giving rise to serious environment pollution, with which all countries are trying to find methods to deal. The influence of relevant technological factors on dephosphorization was investigated in laboratory, and the effect laws of that were analyzed. The results demonstrate that, in the given conditions of the best slag-metal proportion for hot metal dephosphorization is 1:10, and the optimum temperature is 1350 , The phosphorus distribution ratio of dephosphorization agent containing converter dust of 30% has the maximal value, with dephosphorization rate reaching 85%. Under the optimal conditions, premelting dephosphorization agent can significantly improve the ability of dephosphorization, dephosphorization efficiency increasing to 92%. Therefore, the dust can substitute the oxidant and fixative of dephosphorization agent, be used in hot metal dephosphorization, to enhance the efficiency of utilization.

Jan 1, 2016

By Y. Long

The deep-hole surface blasting technique is a prime method of iron ore mining. Blasting fragmentation is one of the important economic indicators that measures the blast method to obtain the iron ore. To improve the efficiency of the blasting method and further reduce the cost of the subsequent processing of iron ore, this paper summarizes measured data gained from a certain amount of blasting test conducted in an iron ore mine in Guangdong province, China. According to the data analysis, there are differences on iron ore blasting fragmentation by different indicators of deep-hole blasting, such as decoupling coefficient of charge, contact state between charge and borehole wall, and change of detonation position in charge. These factors were compared in terms of relevance and impact. Research shows: under certain rock conditions, the decoupling coefficient of the charge has a best range related to blasting fragmentation. Since the detonation position in charge determines the direction of propagation of the explosion stress wave through ore and rock, bottom initiation and mid initiation will help to improve the iron ore blasting fragmentation in joints fractured rock and ore. The research conclusions have important application value for program design of iron ore surface blasting and to guide other types of rock surface blasting.

Aug 1, 2013

By J. Z. Yuan

The purity of rectorite is only about 70% after preliminary mineral processing, which has limited its application. In this research, different pulp densities, different dispersants, different dispersing methods and purification flow sheets were used to purify rectorite. The results show that it is possible to obtain high pure rectorite clay with the purity above 90% and concentrate yield between 24.9% and 29.4% by the purification process with composite dispersants, stirred mill grinding dispersion and so on. The obtained high pure rectorite can be further used in rectorite nanocomposites.

Jan 1, 2014

By Harri J. Lehto, Marja I. Oja

"The purpose of grinding circuits is to produce a particle size distribution that has as much as possible the wanted particle size class. In practise, however, the production of the wanted size class is not at all as simple as it sounds. In the case of industrial minerals for example the end user may give very tight specifications for the particle size distribution and for the chemical composition of the product. This leads in many cases to a very demanding grinding process, if we want to reach and maintain these specifications. In other words, the required size distribution is not necessary the best possible for the chemical composition.Screen models aim to predict the size distribution and flow of the products when a feed size distribution, feed tonnage, and grade efficiency curve are known. The approach used in this study was to select the most suitable empirical model for classification. Suitability of the existing models has been evaluated and accuracy compared. The tests showed that best grade efficiency model was the Rosin-Rammler model.The performance of a screen was evaluated in order to minimize the amount of fine material in the screen overflow. The experiments were carried out using Derrick single-deck screen, first alone with recycling and then in the closed circuit with a rod mill using two different scales. The separate screen tests showed the expected behaviour of the grade efficiency curves. In the pilot tests the Leonard screen efficiencies stayed almost constant. This suggests that the screen works better in a milling circuit. However the loading of the screen turned the product of the mill coarser that helped screening. The grade efficiencies obtained from the pilot tests had the same general shape. The regression analysis of the pilot test runs did not give an acceptable correlation for the parameters. This suggests that pilot tests cannot be directly used to scale or to optimise industrial milling circuits. However they can be used to predict the trends of behaviour of an industrial circuit."

Jan 1, 2003

By Harri J. Lehto, Marja I. Oja

Empirical models used for predicting the performance of screens on the basis of capacity, cut size, water split and grade efficiency curves were evaluated. This paper reports experimental results obtained with single-deck Derrick screens. The performance of the screen was tested with limestone in a separate screen set-up, in a pilot plant and in industrial scale test runs. The results of pilot plant experiments showed that the measured water split was higher than the measured bypass. This is an indication to that water flow does not entrain the same proportion of all fine particles present in the feed which is advantageous for screening. The experimental design for the industrial test runs was made on the basis of the pilot plant tests. Suitability of the existing models has been checked and accuracy compared. The tests showed that best grade efficiency model was the Rosin-Rammler model. An empirical model for the evaluation of the model parameters as a function of pulp density of the feed and the load of the screen is suggested.

Jan 1, 2003

By Yi Luo

Bolting the mine roof is one of the noisiest underground mining operations. The main contribution to the noise is the drilling of the roof bolt holes, especially drilling in hard rock. Previous research shows that the specific energy consumed in drilling bolt holes is inversely proportional to the bite depth (i.e., penetration per drill revolution). Less specific energy at a reasonably high bite depth means less energy is wasted in the drilling process for producing heat, bit wear and noise. Therefore, proper control of the drilling operation to achieve a reasonably higher bite depth can reduce drilling noise from its sources as a proactive noise control approach. In order to explore the feasibility and develop the proactive technology for reducing drilling noise, drilling tests have been conducted in laboratory settings. The preliminary results show that significant reduction in noise dose can be achieved by drilling in medium hard rock with uniaxial compressive strength of about 276 bars (4,000 psi) and at a reasonably high bite depth of about 4.6 mm/rev (0.18 in./rev). This paper presents the findings from laboratory experimental studies.

By L C. Taylor

Both the U. S. Navy and the U. S. Army are interested in knowing more about the loading applied to vehicles which are unfortunate enough to encounter a detonation of a buried mine in the course of performing their normal duties. The Dynamic Effects Laboratory at the University of Maryland has been involved in small scale testing for ten years to assist the Navy and the Army in understanding the loads that are applied to personnel carriers when a buried explosive detonates beneath them. This paper describes results from small scale tests conducted to determine the loading mechanisms on target plates when subjected to loading due to the detonation of a buried mine in saturated sand, dry sand, and water. Transparent target plates were utilized in order to determine the loading process beneath a floor board on armored vehicles. Various charge sizes were scaled in the laboratory accordingly to a standardized full size threat encountered in the battlefield. Tests were conducted in saturated sand, dry sand, and water keeping the stand-off distance of the target and the depth of burial of the charge constant. In the case of water impacting a transparent PMMA plate the crack propagation was recorded and the crack velocity is determined. Additional tests were performed in saturated sand by varying the stand-off distance of the target but keeping the depth of burial of the charge constant. The small-scale test results could be scaled to full scale by using verified scaling laws.

Jan 1, 2016

By A. P. Liu

Semi-industrial test on fine products of Meishan dressing plant was carried out with type RP80/25 high pressure roller mill produced by Homburg Corporation of Germany, and the influences of such factors as energy consumption, water containing, throughput and circulating load on rolling effect were investigated. Closed circuit experiment result showed that Meishan iron ore could be suitable for powder grinding with high pressure roller mill, and energy consumption of the operation was declined by 25%~30%, which was favorable for energy-saving, increasing production efficiency and improving grinding effects. According to above experimental results, this paper put forward the technical proposal of application of high pressure roller mill in Meishan, and pointed out some technical problems which needed to be settled urgently in technology disposal.

Jan 1, 2014

By Heng Yi

The salt lake brines that lithium is extracted from have high chloride levels making the brine very corrosive to stainless steel extraction column internals. This is a significant problem in column scale-up to industrial production. Two types of corrosion-resistant ceramic internals, the hybrid ceramic internal and ceramic plate, were designed and tested under pilot conditions for future industrial application in this field. The hydrodynamic results (Yi et al. Ind Eng Chem Res 56 (4):999–1007 (2016), [1]) show that holdup of hybrid ceramic internal is higher than that of ceramic plate by around 50%, while Sauter mean diameter when using the hybrid ceramic internal is smaller than when using the ceramic plate by around 30%. This results in a larger mass transfer area, hence better mass transfer efficiency for the hybrid ceramic internal. Axial dispersion and mass transfer parameters are also examined (Yi et al. Ind Eng Chem Res 56(11):2049–3058 (2017), [2]). The results show that the column with hybrid ceramic internals has 50% lower axial dispersion coefficient and 50% higher mass transfer coefficient, leading to higher mass transfer efficiency. The transfer unit height of the column using hybrid ceramic internals can be as low as 0.2 m, showing very good efficiency. This is promising for near-future applications. Two-phase computational fluid dynamics (CFD) models have been developed for the two columns with ANSYS FLUENT commercial software. CFD successfully predicts the higher holdup and lower axial dispersion coefficients for the hybrid sieve plate pulsed column as measured in the experiments, and the cause for the difference in performance has been explained with information from CFD.

The rate of liquid copper deoxidation during top blowing of reducing flames has been investigated using a high capacity thermogravimetric unit at 1200 °C. For 1 kg copper samples, it was observed that the rate of deoxidation was proportional to the flow rate of the reducing reagent (H2 or CO). Under similar experimental conditions, it was found that H2 is more effective than CO even though both have similar thermodynamic potential to deoxidize liquid copper. The rate of deoxidation of liquid copper with reducing 0 2/CH4 flames was measured for 0 2/CH4 molar ratios of 1.5 to 2. The deoxidation rate depends on the 0 2/CH4 ratio and decreases as it approaches the stoichiometric ratio (02/CH4 = 2). Estimation of the rate of deoxidation of liquid copper with top blowing flames based on the thermodynamic composition ofH2 and CO in the product gases, agrees well with measured values.

Jan 1, 2007

By Ali Montaser

This paper presents an experimental study conducted to facilitate the use of RFID on construction job sites. The study focuses on deployment settings to provide data acquisition with higher accuracy for indoor location sensing. It provides extension to the state-of-the-art in this field as it addresses the impact of metal media proximity to RFID tags, the reasonable duration for data capturing, number of RFID tags employed and the distance between them. Low cost passive RFID tags were used in the experiments where each tag is used as a reference point with a known location. Five hundred and forty (514) experiments were conducted in lab environment using a 3m by 3m test bed that is dynamically rearranged to generate 15 test beds and a total of 67713 data sets were collected and analyzed. The collected data were captured from nine locations for each test bed at four time intervals. Received Signal Strength Indicator (RSSI) was used as the main attribute for signal measurement to process the captured data. Results of the data analysis performed are studied under four main categories: duration, number of tags, locations of tags and metal interference. The best duration was found to be the 15 second in the test bed with the least number of tags; as the short amount of time to capture data did not allow creation of a lot of interference among the emitted signals. Within each test bed, errors occurred most at points where the received signals were not well distributed in a 360 degree vicinity of the data capturing point. It means that the center point of each test bed resulted in lowest errors and the points located on the extremities led to the highest errors. Finally, metal objects were found to have major impact on the accuracy of the captured data; to the level where reliable values for errors could not be calculated in the test beds attached to metal objects. In summary, the results of the experimental study and related findings are expected to provide guidelines to the users of RFID technology for localization in building construction.

Aug 1, 2013