Search Documents

By S. Fabich

Since the very beginning of Polish copper mining, special consideration of sink shaft techniques through highly saturated Cenozoic rocks was required. Shaft freezing has been chosen as a method to consolidate these rocks. Due to the rock mass structure and water inflow potential, shaft sinking without freezing was considered dangerous. In the course of time, rock mass freezing technology and experience were evolved and this technology became safer and more reliable. New techniques appeared not only in the technical method of freezing, but also in the matter of designing. Computer aided techniques allow engineers to make a detailed analysis and view of freeze wall development. Nevertheless it is important to determine basic thermal rock properties. In this paper, the evolution of knowledge and engineering experience taken in Polish copper mines and current knowledge level in that matter were shown.

Aug 1, 2013

By H. Colijn

The problem of the freezing of moist raw materials, such as concentrates, in railroad cars during winter shipment has been a continuing source of both economic and operational trouble to the industry and to the railroad companies. The difficulties center around the discharging of frozen cargoes into the plant materials handling system. Because of cargo freezing, appreciable delays in car-dumping schedules occur each winter and cause additional expense for demurrage charges and for slowdown of plant operations. In one plant during one winter, a car dumper rated at 40 cars per day could dump only 3 cars per day in bad weather. Delays became so serious one winter, that 500 cars held in the yard became so badly frozen, that they were sent to the southern part of the United States to thaw after they accumulated an average of two months demurrage charges. These delays in car unloading become critical if unit or integral train concept is applied to the movement of raw materials. Anticipated savings in transportation costs through better equipment utilization are largely based on rapid loading and unloading cycles of whole trainloads. If freezing problems cannot be adequately solved, unit train operations cannot be operated to achieve the potentially large reductions in transportation costs. The freezing problem may tend to become even greater in the years ahead, because the unit train concept will allow the trains to run faster and consequently the heat loss will be accelerated due to the larger heat transfer coefficient. A compensating factor, however, will be the shorter travel time. Further, the sources of raw materials being mined are located farther north than before and the ambient temperatures during transit are going to be lower.

Jan 1, 1976

By T. R. Braithwaite

The brief comments made in this chapter deal mainly with shaft sinking, but don't assume that freezing techniques apply only to shaft sinking. They can be used on tunnel work, on such things as liquid gas storage in sediment, and I think you will probably see other applications for it as we go along. The method was first developed in 1883 and was used to sink shallow shafts through water-bearing overburden in Germany and in England. One of the early shafts was in Germany and was sunk by freezing to 310-ft depth. The project required 17 months for drilling, roughly 5 1/2 months for freezing, and another 7 months for sinking, giving an average progress of 10 ½ fpm. Fortunately there have been numerous improvements and new developments in this technique through the years. With equipment and techniques available today, we can take a 20-ft-diam shaft down through 2000 ft of water-saturated overburden and the time schedule runs roughly 4 months for site preparation, freeze-hole drilling, installing the casings, and setting up the plant; 4 ½ months for freezing; and 6 months for excavating and installing permanent linings. This gives a progress rate of about 140 fpm, on average. I might qualify that a little in that the special linings that are required for some formations can affect the time. If it's straightforward sinking where one can use a heavy concrete lining, up to 630-640 fpm may be achieved in a shaft; but with special cast-iron tubbing or types like that, 5 fpd is pretty good progress, so the lining does affect the time. The freezing method is used mainly for sinking shafts through unstable water-bearing formations which cannot be grouted either effectively or economically and which are too deep to enclose in pile casing. Even with overburden, grouting methods available today can handle roughly 100 lb water pressure; in the range of, say, 100 to 150 ft from the surface, it's very often best to grout 40 or 50 ft. You normally drive a pile casing and go through it. Below that range, freezing is very often the economical

Jan 1, 1970

By W. B. Burchall

Introduction In presenting this paper the author wishes to state that the opinions here given represent only his personal views. A general survey of the subject has been attempted, but such deductions as may have been drawn are not necessarily endorsed by the Company with which he is associated. The aeroplane as an instrument of transport is yet a novelty, for it is only twenty-five years since man first flew. This statement, by itself, may be very deceptive, for compared with the steam locomotive or even the auto-mobile, this infant in industry has made some remarkable showings. The 'actual performance' speed-curve of aircraft plotted over a ten-year period is rising faster than the 'expectancy' speed-curve of 1924 indicated, and it should be noted that, today, the possibilities of 600 miles per hour provoke less scepticism than did the prophecies of 400 miles per hour only a decade ago. Commencing with the remarkable achievement of raising one man into the air, aircraft with an all-up weight of 14 tons are now in daily use on the British airways, and recently a non-stop flight of 5,340 miles was accomplished in an aeroplane, without refuelling. More true than ever is the statement that the records of yesterday are commonplace tomorrow, for new ideas are today seized on and exploited to the utmost once the period of scepticism and doubt has been overcome. In fact, so many new ideas have been brought forward, during the past few years, and applied successfully in our economic life, that one may well ask if today we are not a little too impatient, too exacting in demands, forgetting that real worth-while progress -is attained by no short-cuts.

Jan 1, 1933

By H. F. Yancey

One of the important duties of the Bureau of Mines is to sample and analyze coals and to publish the results of such analyses for the information of producers, consumers, and the general public. Numerous publications containing such analyses have been Issued from time to time. Although the chemical properties of a coal as revealed by its proximate and/or ultimate analysis and heating value aid one considerably in visualizing its probable behavior and in determining its usefulness and value for a specific purpose, they do not furnish complete information. The physical properties of a coal, such as its ability to retain its original form without undue breakage or degradation in size under the various conditions of storage and usage, are also of importance in determining its suitability, technically or economically, for a given purpose.

Jan 1, 1932

By T M. Nester, D J. Reardon, A N. Page, B J. Barsanti

The load capacity of a friction bolt has long been regarded as 4 t/m of embedment for ground support design analysis and supported by in situ pull test results. In recent years, the authors have observed lower pull test results or inconsistent results which were rarely sighted in the early 2000s. The lower pull test results indicated in some cases that reliable friction bolt capacity (≥90 per cent of results) is closer to 3 t/m of embedment with some geotechnical engineers adjusting the ground support parameters in the design work accordingly. This can be in contrast with other mines which reliably obtain 4 t/m (or greater) using the same suppliers bolt in similar ground conditions. This raised several questions: • What is the effect of poor installation (bolt twist or bolt hole deviation)? • Does the performance of friction bolts vary in different rock masses? • Does bolt performance vary between suppliers? • What effect does increased jumbo feed/percussion/rotation settings have? • Have the bolt dimensions or steel strip width changed? • Have the physical bolt properties changed? • Have the steel properties changed? This paper was aimed to answer as many of these questions as possible and discuss each variable in detail. This project included friction bolt trials at various mine sites across Australia, multiple friction bolt manufacturers, steel manufacturers and laboratory analysis. The paper also includes discussion on what the authors consider best practice for pull testing. It should be noted, the terms ‘friction stabiliser’ and ‘split set’ used in this paper are used in a generic manner and is not linked to any specific ground support supplier. Whilst its acknowledged within the industry the term split set and friction stabiliser is used interchangeably, the authors acknowledge that the term split set is a trademark of Split Set Mining Systems and has been used in context in this paper.

Nov 29, 2022

By John P. Turner, Benjamin J. Turner

"Tieback anchors are now used routinely for landslide stabilization in the USA and abroad. It is generally understood by design engineers that friction loss over the unbonded length of a tieback anchor is inherent to the system, and such loss is permitted as long as it does not exceed a certain threshold, typically 20 percent of the post-tensioning load. However, recent experience from projects utilizing tieback anchors with unbonded lengths in excess of 150 feet has demonstrated that this criterion may be difficult to achieve, particularly in certain ground conditions. Furthermore, anchor friction loss, even if below the 20-percent threshold, has important implications for the stability of the slope that are often ignored in practice. This paper presents the results of a study in which friction loss is quantified from load test data for projects in a variety of ground conditions by means of a “wobble coefficient.” Factors that may influence the wobble coefficient are examined, and recommendations for addressing this issue in practice are presented. A recent instrumented load-test program for a landslide stabilization project in Southern California is examined, demonstrating that with appropriate monitoring controls, uncertainty with regard to friction loss can be minimized. IntroductionSteel-strand tieback anchors have been used by the geotechnical community to support shoring systems for many decades, and more recently as a means to stabilize landslides. For strand encased in grease-filled plastic sheathing, which is intended to allow the strand to elongate freely, some load can still be transferred by friction between the strand and the grease and between the grease and sheathing. The sheathing then transfers load to the surrounding grout and, in the case of ground anchors, to the surrounding soil or rock. The resulting decrease in load over the length of the unbonded zone is known as “friction loss.”A widely used criterion for ground anchor acceptance based on load testing is that the measured anchor elongation must achieve a minimum value of 80 percent of the theoretical elastic elongation, or in other words the actual elongation can be up to 20 percent less than the theoretical value. This ensures that the majority of the load applied at the anchor head is reaching the bond zone behind the assumed failure surface, since load shed within the failure mass does not contribute to stability. This criterion acknowledges that friction loss is an inherent feature of the anchor system which cannot be eliminated completely, only minimized."

Jan 1, 2017

By von Wielligh. L., D. G. Hattingh, M. N. James, W. Thomas

"SynopsisThe process of joining materials by friction is based on generating the heat necessary to create a solid-state mechanical bond between two faying surfaces to be joined. In simple terms, the components to be joined are subjected to frictional heating between rubbing surfaces, causing an increase in interface temperature and leading to localized softening of interface material, creating what is described as a ’third body’ plasticized layer. This plasticized zone reduces the energy input rate from frictional heating and hence prevents macroscopic melting. The plasticized layer can no longer transmit sufficient stress as it effectively behaves as a lubricant (Boldyrev and Voinov, 1980; Godet, 1984; Singer, 1998; Suery, Blandin, and Dendievel, 1994). The potential for this solid-state frictional joining process to create high-performance joints between, for example, dissimilar materials with limited detrimental metallurgical impact, and reduced defect population and residual stress level, has had a very significant impact on fabrication and repair in industrial sectors such as transport. This paper presents a brief overview of the advances made within the family of friction processing technologies that could potentially be exploited in the nuclear industry as alternative joining and repair techniques to fusion welding.Modern friction processing technologies can be placed into two main categories: those that make use of a consumable tool to achieve the intended repair or joint (friction stud and friction hydro-pillar processing) and those making use of a non-consumable tool (friction stir welding). The most mature friction joining technology is friction rotary welding, where a joint is formed between original parent materials only. A new addition in this category is linear friction welding, which opens the potential for joining complex near-net-shape geometries by friction heating. The continuous innovation in friction processing over the last 25 years has led to the development of a number of unique processes and applications, highlighting the adaptability of friction processes for specialized applications for high-value engineering components.IntroductionAssessing the potential for using alternative joining and repair techniques for specific applications in a given industrial sector is informed by an appreciation of the current size and potential growth in that sector. Power generation by nuclear fission has been out of favour over the past few years, due to several high-profile nuclear incidents, e.g. the Fukushima Daiichi nuclear disaster, as well as concerns over disposal of nuclear waste and spent fuel rods. However, due to rapid increases in the demand for electricity, coupled with many fossil-fuel fired plants reaching end-of-life, there is renewed interest in installing additional nuclear capacity."

Jan 1, 2015

By R Varden

Friction rock stabilisers, commonly termed ‘Split Sets’, friction rock bolts, or continuous friction coupled bolts are the most widely used rock bolt in the Australian underground metalliferous industry. Historically, they were used for temporary reinforcement, mainly within ore development. However, their use as primary reinforcement has grown with the demand for higher development rates at lower costs. The introduction of galvanisation has increased their longevity and pattern bolting in conjunction with weld mesh, specifically made for use in development headings, has allowed the use of friction rock stabilisers to increase rapidly with development jumbo’s undertaking the installation. The installation of friction rock stabilisers appears to be deceptively simple, particularly when compared to resin encapsulated bolts. The friction rock stabilisers capacity is a function of the borehole parameters, rock mass quality/strength, the bolt dimensions and steel quality, and lastly and perhaps the most important the operator skill levels. However, as in industry we are still seeing common occurrences of friction rock stabilisers not reaching their design pull test capacity. Pull testing the friction rock stabilisers is used to verify the installation of the design capacity. It involves loading the collar of the bolt with a hydraulic ram until the design load is reached or the bolt slips. Pull tests often show failure rates of 20 per cent or higher. This is despite over 40 years of use and with millions of units installed annually. Such high failure rates would suggest there remain issues with the quality of installation. Ground support quality assurance and quality control (QAQC) programs are needed in combination with operator training to ensure that pull test failure rates are kept as low as practical. However, there are times when despite the QAQC being completed the pull test failure rates increase quite suddenly. When this occurs, it is important to conduct a thorough investigation. These investigations often show there are several factors that are not obvious to personnel installing the bolts. To complete a useful investigation, it must also be done methodically, working through the entire process that includes less obvious factors such as steel quality and the calibration of the hydraulic pull test kit. The aim of the paper is to give mine practitioners an understanding of the complexities of friction rock stabilisers, what QAQC requirements they should be doing on-site, what can go wrong during installation and, if necessary, a process of how to conduct investigations into high friction rock stabiliser pull test failure rates.

Mar 29, 2023

By Farzad Khodabakhshi, Adrian P. Gerlich

"In this article, cold spraying process was utilized to coat the surface of AZ31 magnesium alloy with a layer of AA7075 aluminum alloy. Thereafter, friction-stir processing (FSP) was employed to enhance the microstructure and consolidate the deposited layer. The grain structure and phase morphology were studied along with indentation hardness before and after cold spraying and friction stir processing. The magnesium substrate had an initial hardness of 74 HV which increased to 102 HV after FSP due to refinement of grains to <2 µm. The aluminum coating layer, provided improved surface hardness up to 160 HV, which further increased to 173 HV after FSP was applied.INTRODUCTION Cold spray is a material deposition process which can be used for surface modification, since it deposits material on a metallic substrate with little heating by way of high velocity ballistic impacts. Using cold spray technology, it is possible to deposit a wide range of coatings with various thicknesses by controlling the characteristics of the feeding powder and metal substrate, gas temperature, gas pressure, powder feeding rate, nozzle geometry, and gun traverse velocity. This process has been recently employed for surface modification in various aircraft and automobile structural applications. This has led to a broad range of research using this process for production and modification of different metallic and non-metallic systems. In the present study, cold spray process was used to deposit a uniform layer of aluminum-zinc alloy (AA7075) on the surface of AZ31 magnesium alloy. This coating was subsequently treated by way of friction-stir processing (FSP) as a new post-spraying modification technique to enhance the structural homogeneity and densification of the coated aluminum layer. This method utilizes a non-consumable rotating tool with a specially designed shoulder and pin that is plunged into the surface of metal to be modified and then moved along the direction of interest. The localized frictional heating between the rotating tool and workpiece leads to softening of the materials around the pin, and material extrusion through a complex flow of material from the advancing toward the retreating side the tool. To the author’s best knowledge, only a few reports discuss the modification of a cold sprayed deposit by FSP process. The microstructure and mechanical properties of the cold sprayed layer and substrate before and after FSP modification were examined using optical observations (OM) and indentation hardness testing. Furthermore, the AZ31 alloy substrate alone was treated with FSP as well, for the aim of comparison to the processed coating."

Jan 1, 2017

By Farzad Khodabakhshi, Adrian P. Gerlich

"Multi-pass friction stir processing (FSP) was performed to fabricate a new Al-Mg-Graphene nanocomposite. Microstructural developments and distribution of graphene were studied by using electron backscattering diffraction (EBSD) and transmission electron microscopy (TEM) analysis. In the stirred zone (SZ), grain structure was refined down to about 2 µm attributing to the operative dynamic restoration mechanisms and the locking effect of graphene phase. As a result, the yield strength of Al-Mg alloy was improved more than two times due to incorporation of graphene nano-sheets. Also, the indentation hardness resistance of nanocomposite was increased up to ~60%.INTRODUCTION Aluminum-matrix nanocomposites have garnered significant in recent years due to their superior performance and potential advantages for several industrial applications including the automotive and aerospace sectors. Among various reinforcing nano-materials, carbon-based structures featuring sp2 or sp3 hybridization bonds have been found to offer considerably improved physical and mechanical properties. Such carbon allotropes form at micro- and nano-scales including; graphite, carbon nano-tube (CNT), nano-fiber, and graphene. The potential of two-dimensional (2D) carbon materials was introduced in 2004, with the development of graphene as an alternate 2D allotropic form of the carbon structure with a honey-comb lattice at the atomic-scale. It has been shown that it is currently among the strongest materials ever tested with an intrinsic tensile strength of 130 GPa and Young’s modulus of 1000 GPa, and also offers unique thermal and electrical properties.To fabricate metal-matrix nanocomposites reinforced by graphene nano-sheets with typical metallurgical processing techniques, some attempts have been reported in the literature for various solid-state techniques including; hot rolling, mechanical alloying, and friction stir processing (FSP) of pre-cast plates or surface dispersed graphene oxides. The main challenge in those methods was to facilitate the considerable high temperature and pressure for attaining a uniform dispersion of the nano-sheets during the consolidation process. In most cases, significant difficulties have been reported in obtaining a uniform dispersion of graphene within the metal matrix. Among various techniques for production of metal-matrix nanocomposites, FSP has attracted significant attention as a method of surface modification since it was first reported by Mishra et al. In this process, a non-consumable rotating tool is plunged into the surface of material for the aim of microstructure modification. Extreme material plasticity is induced without melting as a result of friction between the tool and workpiece. Frictional heating and severe plastic deformation induced by the FSP process enables metal matrix nanocomposite fabrication by softening the base material and mechanical stirring to disperse the reinforcing nano-materials into the matrix."

Jan 1, 2017

By Open-Hearth Steel

I received a telegram yesterday from Mr. J. H. Nead saying that he regretted circumstances had come up which prevent his attending the meeting, but that arrangements have been made and Mr. T. S. Washburn, of Inland Steel, will act as the Co-Chairman in his stead. We are sorry, of course, that he cannot be here at this conference. We have, therefore, asked Mr. James J. Bowden, chief metallurgist of Republic Steel Corporation, Cleveland, to act as Chairman and Mr. Tom Washburn to act as Co-Chairman. I will turn the meeting over to these gentlemen at this time.

Jan 1, 1940

By John Loop, W. A. Gibbins, Donald D. Hogarth

"Introduction Background The Frobisher voyages of 1577 and 1578 were organized by the Cathay Company for the express purpose of finding and mining gold ore. Since publication of the Baffm expedition of Charles Francis Hallill, the location of Kodlunarn or Countess of Warwick Island, the headquarters of Frobisher&apos;s third (1578) voyage, and focal point of the largest Arctic voyage of all time, has been known to the world. Through Hall we also know the location of the Countess of Warwick Mine on Kodlunarn Island. However, the exact locations of the other mines are not known. Of the ""ore"" we know little. Pieces of the original ""black stone"", once as large as ""a half-penny loaf&apos; have now disappeared altogether. Specimens collected at random from the repository of shipments in England and from loose rock on Kodlunarn Island were termed, respectively, ""hornblende pyroxenite"" and ""amphibolite"" and from a locale about 200 yards from Kodlunarn as (hornblende) ""pyroxenite""121. However, it is uncertain whether these specimens are representative of Kodlunarn or of the other mines, although Blackadar131 notes that, in the northern trench of Kodlunarn, biotite gneiss contains lenses and bands of amphibolite. The ""gold"" itself is even less well defined. It has long been accepted that gold was virtually absent in Frobisher&apos;s ore. The ""gold"" has been termed pyrite, biotite and both biotite and pyrite together. Even t h e word "" marquesset"" , which appears and reappears in contemporary descriptions, is nebulous and is defined as ""a stone participating in the nature of some metal, yet in so small quantity, that the metal cannot be melted from it"" (0.E.D., definition of 1616)."

Jan 1, 1999

By J. P. Nicoud

"The Frog&apos;s Leg project is located in the Kundana mining centre 22 kms West of Kalgoorlie, in Western Australia. The Mines and Resources Australia (MRA) Dioro Exploration Joint Venture has had considerable exploration success centred on the high grade Frog&apos;s Leg discovery. A gold resource of 930,000 ounces has been defined. At Frog&apos;s Leg there have been three discrete resource domains recognised - Supergene, Contact, and Quartz Lodes. This paper describes the metallurgical test work undertaken.The selection of the drill core was a joint effort by the MRA Senior Geologist and Mineral Engineering Technical Services (METS) to ensure the samples were representative of the ore body. Optimisation of gold recovery was essential as both the Contact and Quartz Lodes have exceptionally high percentages of free gold as well as significantly higher grades than the typical open pit ores found in Western Australia. The metallurgical scope of work included documenting all of the metallurgical test results, establishing the comminution characteristics, determining the percentage of gravity recoverable gold, evaluating the cyanide leach characteristics and determining the tailings characteristics. These studies were used as the basis of flow sheet design to treat both ores and to discuss the advantages and disadvantages of alternative flowsheets. Investigations also included toll milling options at various plants as well as second hand and transportable plants. Considerable technical effort has been put into ore characterisation by way of test work aimed at managing the process risk at each stage of project development, including mitigation. MRA also carried out detailed mineralogical analysis of the ores."

Jan 1, 2005

"The most common comminution testing methods and the associated analytical procedures provide average values and do not capture the variability in breakage behaviour of ore particles. Therefore, plant designs and process performance predictions use only average values; hence, the inherent variability that exists within an ore domain translates into variation in process performance. This paper discusses the drawbacks of using the average approach to impact comminution testing and plant design. It considers breakage intensity from a single-particle testing perspective. To clearly delineate breakage behaviour of each broken particle, an experimental technique using the JK Drop Weight Tester (JKDWT) has been developed by which actual comminution energy per particle and breakage intensities were measured directly. Four different ore types in ranges of -45+37.5mm and -22.4+19mm were tested at three energy levels of 0.1, 0.25, 0.5 kWh/t and six energy levels of 0.5, 1.0, 2.0, 2.5, 3.0 and 4.0 kWh/t, respectively. Sieved results of individual particles, notionally, t5, t10 and t50 showed the presence of large variability in their breakage behaviour, which was not captured by the standard JK impact breakage testing approach. In addition, the original JKMRC model is modified by introducing a third parameter, ‘Emint10’ which describes the minimum energy required to produce the minimum percent t10 for a given ore type and its significance is tested statistically. These results suggest that the analysis of breakage variability may lead to more robust plant designs. Perhaps, the most useful insight from this work is to extend single particle breakage model developed by JKMRC to a comminution percentile envelope which may provide a more detailed picture of ore breakage variability. INTRODUCTION Rock consists of mineral grains, pores, voids and cracks that may differ markedly in size/density which make rock a heterogeneous material by nature. The degree of heterogeneity in rock affects its breakage characteristics where these variations increase local differential strain and stress within a stressed rock (Scholz, 1968) and it depends on many factors such as rock genesis, alterations, etc. One important aspect of this heterogeneous feature is presence of a large amount of experimental scatter in rock breakage results when considered from a quantitative perspective (Bieniawski, 1967; Liu, Roquete, Kou, & Lindqvist, 2004)."

Jan 1, 2018

By H J. Dalstra

High-grade iron ore may be derived from banded iron formation (BIF) through four fundamentally different processes:1. syngenetic precipitation of chert free BIF,2. residual enrichment by removal of gangue minerals from BIF to form bedded (residual) ironore,3. mechanical erosion of iron oxide and chert from bedded iron ore or BIF and re-deposition andupgrading as detrital iron ore, and4. chemical removal of iron from BIF and precipitation elsewhere as a secondary (channel) irondeposit.Finally, the BIF itself may constitute iron ore if a high-grade concentrate utilised for pellets or sinters can be derived from it through mechanical (industrial) separation of iron oxide by means of crushing/milling and mineral separation.Historically, exploration for high-grade BIF hosted iron ores was focused on the residual (bedded) deposits and driven by supergene concepts. Exploration for detrital and channel type iron ores was mostly secondary to exploration for bedded deposits, but recently, a more focused exploration effort has led to the discovery of enormous moderate to low iron grade deposits in the Pilbara region of Western Australia. Exploration for high-grade iron ores using syngenetic concepts has been limited,but together with exploration using hypogene concepts offers the best hope of fi nding concealed deposits. Exploration for BIF sources suitable for concentrate ores commenced in the ‘old’ iron ore provinces after the high-grade resources were depleted and has only recently gained importance in Australian BIF provinces, mainly as a result of high iron ore prices in the last decade.

Jul 11, 2011

By B Young

Variable bench heights, interaction with underground workings and a steeply dipping orebody are challenges faced daily by geologists at Xstrata Zinc’s Black Star Open Cut (BSOC) Zinc/Lead/Silver mine in Mount Isa, Queensland.BSOC has been in operation since late 2004 and was developed to extract the surface extents of the Zn/Pb/Ag mineralisation mined in the underground lead mine. To date many large scale stopes and extensive development drives have been intersected and successfully mined. The stratigraphically hosted orebodies strike in a north-north westerly direction, dipping ~75&#176; west. Ore production from the pit is currently at 4.5 Mt/a.Historically, sampling was conducted using a multiple spear technique from blasthole cuttings. This method proved to be relatively reliable when blasting benches at a consistent height, but a requirement to vary bench heights to safely collapse and then mine through underground workings reduced sample representivity to unacceptable levels.The purchase and commissioning of a production rig which had been converted for reverse circulation (RC) has allowed for the flexibility of a small rig, with the capacity to easily drill 48 m holes while ensuring sample quality. Sample quality is not the only benefit of introducing RC grade control. By collecting grade control data well in advance, informed decisions can be made by planning, drill and blast and mining departments weeks beforehand, rather than hours before firing. Additionally, seeking operational value to offset higher drilling costs has proved positive with benefits including increased confidence in orebody wireframes, accurate tonnage and grade for proceeding five benches along with the ability to representatively test metallurgical response&#160;on a tight grid spacing.

Aug 22, 2011

By E. J. Y., G. J. McLachlan, E. Amini, Koha

Inferring individual component flotation rates from recovery-time data of ore complexes is important in optimising and designing minerals processing plants. However, existing two-component first-order flotation models are computationally intensive to solve using conventional non-linear least squares regression. In this paper, a Convolutional Neural Network (CNN) is used to approximate the inverse function which predicts the two-component first-order model parameters using recovery-time data. This paper compares the accuracy and computation speed of the proposed CNN against traditional non-linear least squares regression on 1 million generated data based on a known two-component firstorder kinetic model. It is shown that using a CNN is possible to approximate the inverse function for the non-invertible two-component model with recovery-time as an input matrix for convolution operations. The CNN method is 450 times faster to compute than the Trust-Region (TR) non-linear least squares regression algorithm. However, the CNN model is less accurate compared to the TR algorithm overall. Keywords: Flotation kinetics, convolutional neural network, inverse problem, modelling and simulations

Jan 1, 2020

By Norman O. Lotter, Virginia Lawson, Mika Muinonen, Dominic Fragomeni, Jorge F. Oliveira

Development of metallurgical flowsheets from drill core to production of finished metal involves two main domains: process mineralogy to sample the ore and develop a successful flowsheet producing saleable concentrate; and extractive metallurgy to convert that saleable concentrate to finished metal. Effective flowsheet development for a new or brown-field concentrator and processing facility is essential to project schedule and return on investment. Over the last decade in particular, the integration of geology, mineralogy, sampling, and mineral processing have empowered the development of an improved practice in flowsheet development. The use of geometallurgical units as a basis for best-practice sampling delivers representative study material to the laboratory. Modern automated mineralogy characterises the whole rock assembly and paymetal mineral hosting, to address downstream process implications. Batch scale flotation testing then uses this information to design and perform well-focused strategies. At early stages of the project, the Extractive Metallurgy team is engaged to determine processing constraints or other economic drivers in conversion of the saleable concentrate into finished metal. The team evaluates available technologies, assesses the impurities and key properties of the given concentrate. In many cases, changes to mineral processing flowsheet are required to maximize value per tonne of concentrate. Site conditions, availability of infrastructure, energy and power all play an important role. Modern metallurgical simulation tools such as FactSage™ and METSIM™ can quickly define the appropriate test program for each process. Bench scale testing and appropriate scale of piloting can confirm simulations and provide design criteria. A case study demonstrates how effective use of these tools and a multidisciplinary team can accelerate flowsheet development, while reducing costs and ensuring that the designed processing facilities maximize project value with minimum risk.

Jan 1, 2014

By A Gustafson, D Johansson, K Jonsson

The underground mining process, from in situ characteristics of the unmined rock mass to the final mill product with fully liberated minerals, consists of a chain of unit operations. Some of them influence fragmentation while fragmentation impacts others. From a production point of view, fragmentation is a key parameter for the proper functioning of many unit operations and affects total production; it influences the ability to load, haul and crush the rock later in the process. Fragmentation varies because of rock mass strength, the presence of joints, the chosen explosive, specific charge (kg/m3) and quality of drill holes. The efficiency and result of unit operations such as drilling, blasting, loading and crushing depend on the rock properties, which vary throughout a mine. Generally speaking, operations are not well adapted to the actual rock properties, leading to a non-optimised flow in production. This paper presents the initial part of a project that will build knowledge on the impact of fragmentation on each step of the production chain in an underground mine. It identifies the key parameters of fragmentation, which influence the overall energy consumption and productivity in a mining operation through interviews, mine visits and a literature review. In the subsequent stages of the project, a number of field tests in the case study mine will address important segments of the production process where fragmentation is a major obstacle to improvements. Optimising the entire process, rather than isolated unit operations, will lead to increased productivity, decreased amount of interruptions and lower energy consumption.CITATION:Gustafson, A, Jonsson, K, Johansson, D and Schunnesson, H, 2016. From face to surface – a fragmentation study, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 555–562 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016