Search Documents

By C. Özgen Karacan

This study presents the results of core-log analyses from the exploration boreholes, the analyses of face advance rates, and the results of downhole monitoring studies performed in gob gas ventholes for calculation of changes in hydraulic properties in the longwall overburden at a mine site in southwestern (SW) Pennsylvania section of Northern Appalachian Basin. In the ?rst part of the study, coal measure rocks in overburden strata were analyzed and the locations where possible fractures and bedding plane separations would occur were evaluated. In the second part, the hydraulic conductivities were computed by two different slug test analyses methods using the water level changes measured in gob gas ventholes as longwall face approached. Hydraulic conductivities were analyzed with respect to the changes in overburden depth, the locations of the borehole, and mine face advance rates. These data were used to interpret the potential productivities of the gob gas ventholes as a result of fracturing and changes in hydraulic conductivities. The general results showed that the probability of fracturing and bedding plane separations in the overburden increase between strong and weak rock interfaces. Also, the probability of bedding plane separations increases as the interface is close to the extracted coal seam. Evaluation of slug tests showed that the hydraulic conductivity developments in the boreholes and their potential production performances are affected by the underground strata and the roof materials. In situations where the roof material is stiff and thick, the development of high permeability fractures around the borehole will be less. Results also indicated that borehole location with respect to face position affects the fracturing time and permeability evolution as well. Greater overburden depths generally cause earlier fracturing as longwall face approaches, but eventually result in lower hydraulic conductivities and potentially less effective boreholes. Increasing mining rates also resulted in generally lower hydraulic conductivities in the overburden. The results of this study were intended to improve the interpretation of gob gas venthole performance and to provide better siting of these boreholes.

Jan 1, 2009

By Henry G. Granger

I. INTRODUCTION. REPEATED failures in attempts to work gold-bearing gravels by means of suction-dredges have created the impression that this method is impracticable. The suction-dredges have failed from three special causes excessive wear and frequent breakage of pump-shell, runners and liners; inability to dredge compact gravel which would ,not. readily move towards the intake; and, most important of all, closing. of the suction-pipe by stones too large to enter it. In my opinion, all three causes of trouble may be remedied: the first, by making stronger the parts most liable to wear and breakage; the second, by means for loosening the gravel at the intake; and the third, by sufficiently... Increasing.. the diameter of the suction-pipe. In suction gold-dredges, this diameter has not usually exceeded 10 or 12 in.; whereas there are few profitable gold-fields which can bee considered dredgeable, in which stones more than' 12 in. in diameter, are-.not frequently encountered. II. AN EFFECTIVE SUCTION-DREDGE. In harbor-operations, much larger stones are handled by suction-dredges.., The large dredge of the Henry Steers Contracting Co. worked for nearly four years at League Island, Philadelphia, where it sucked up, passed through the pump, and forced through 3,700 ft. of discharge-pipe; gravel containing boulders up to 200 lb. in weight. This was done with no bad breaks and few shut-downs. The cutter; and liners were the only parts liable to damage, and these were easily replaced with brief interruption of work. The chrome-steel liners are said to have lasted from six to nine months. I am informed that this dredge worked continously for nine

Apr 1, 1909

By E. A. Sobering

Hydraulic filling or sand filling is a system used to fill underground excavations with a dense pulp. Milltailings are commonly used. The resultant fill, after being placed and de-watered, is known as hydraulic fill. These fills have been effectively used to (a) provide immediate support of the workings place during stoping; (b) .facilitate the recovery of pillars; (c) limit surface damage by subsidence; (d) permit the mining of parallel hanging-wall orebodies; (e) stabilize the ground in mines, thereby reducing the rock burst hazard; (f) control and prevent mine fires; and (g) solve tailings disposal .problems. The various uses of hydraulic filling have been developed during the last ninety years. In 1864 it was employed only to control surface subsidence. Since then, this system has been successfully applied to meet specific ground support problems. Methods of handling mine-fill derived from a source outside the stope include transportation ?Of the material by hand, mechanical, pneumatic, and hydraulic means, or a combination of these methods. The hydraulic method has many advantages not found in the others; a significant advantage is the low compressibility of the material when compared to other mine-fill material. The hydraulic filling operation includes the .preparation and transportation of the pulp. The underground practices in .placing the fill vary from mine to mine. The chief reason, formerly, for using hydraulic fill was the exceptional support it provided, but recently it has proven an important means of reducing mining costs. This is especially true where labour is a large part of an alternative method, or where timber consumption is greatly reduced. The indirect benefits of hydraulic filling are probably as important as the direct benefits, and few important disadvantages exist.

Jan 1, 1956

By Tim Deans

This paper will address methods to manage hydraulic hose and coupling inventory so that parts will be available to build assemblies for the vast majority of equipment with as little inventory as possible. Topics also to be covered will include some basic hose assembly tagging techniques that will help keep equipment running by tracking problem hoses and building ?band aid? kits, having problem hoses premade in stock, and inventory usage tracking (one of the biggest problems for any inventory manager is knowing which couplings have been used so they can re-order). Cradle to grave tracking of hydraulic and industrial hoses insures reliable service of vehicles and ethical disposal of old hoses and couplings. With accountability for disposal of hose products that may contain chlorine (neoprene tube material in some hydraulic hoses) and carbon black that will be scrutinized more closely in the future, a proactive approach should be adopted in order to minimize maintenance facility problems.

Aug 1, 2013

By P. Kostuik

"Recent interest in the pipeline transport of solid mate-als has been sparked by the idea that, in an inflationary onomy, pipeline costs are more stable than the costs of any other transport systems. Pipelines have proved over 1e years to be dependable, records indicate that main-•nance and operating costs are comparatively low, and 1eir amenability to automation is of considerable im->rtance.The concept of hydraulic hoisting of solids from under-round, or cross-country hydraulic transportation of con-~ntrates and ores, is currently of prime interest to the ining industry. In general, this paper deals with a preliminary investi-ation of energy losses incurred while transporting a rela-vely heavy, crushed mine product, namely magnetite, oth vertically and horizontally. The basis and validity of everal equations derived by other experimenters to com-ute these losses is discussed. A theoretical analysis of ydraulic hoi:,,ting is made, and, based upon test results, calculation of horsepower requirements for hoisting an re under a given set of conditions is presented. Results indicate that:n vertical transport, the friction head losses are identical to those of clear water, and the total energy requirement for hydraulic hoisting then becomes a function of height of lift, concentration and specific gravity of the solids being hoisted. .-In horizontal transport, friction head losses can be calculated with reasonable accuracy using Bonning-ton's correlation curve. Losses computed utilizing Durand's correlation (K = 85) result in estimates which are too low by 10 to 30 per cent, an<l those calculated using Newitt's correlation (K = 1,100, K = 66) give friction loss values which are too high by 10 to 30 per cent . . -The theoretical horsepower (RMS-hp.) required for hoisting hydraulically is approximately half of that required for conventional double-drum skip hoisting."

Jan 1, 1966

By D. Hu, L. Matzar, J. Hampton, M. Gutierrez

Nanodarcy permeability is common in many oil- and gas-bearing formations requiring unconventional stimulation technologies, such as hydraulic fracturing (HF), which can connect the isolated hydrocarbon-rich pores with a wellbore through induced fracture networks. Even though a dense induced fracture network is capable of accessing economic amounts of hydrocarbons, much of the rock between and very close to the fracture network is still un-accessed and contains extremely low permeability. Inducing fracture networks into brittle rock can create large amounts of micro failures in surrounding regions that are not connected to the wellbore, as can be seen in Fig. 1(a) from the very wide acoustic emissions (AEs) cloud associated with a narrow fracture generation. It is possible in certain types of rock to increase the effective matrix permeability in localized regions based on the damage associated with the surrounding hydraulic fractures and subsequent high stress concentrations along localized pre-existing potential failure zones. To study this problem, laboratory HF tests were performed at true-triaxial stress state in brittle crystalline rock while monitoring AEs. The AE associated with HF was analyzed for source parameters using the moment tensor inversion method called Simplified Green’s Functions for Moment Tensor Analysis (SiGMA). Using the moment tensor for each individual AE event, the mode of failure was determined. Crack slip directions and crack face normal directions were also found, along with the relative volume of individual micro failures as well as a damage parameter. The associated source parameters were used to classify differing regions of damage in the sample induced from HF and correlate these regions of differing damage to the effective drainage region. Shown in Fig. 1(b) is a near-wellbore (NWB) region that contained three times larger average relative volumetric deformation of individual tensile AE events than the average tensile AE event volume from the entire sample. Because of the large difference in micro fracture volumetric deformation for the NWB region compared to the entire sample, predictions of HF induced damage must be included in reservoir drainage predictions.

Jan 1, 2015

By JESSICA W. A. AZURE, Samuel Frimpong, AZUPURI G. A. KABA, FORSYTH A. KADINGDI, PROSPER E. A. AYAWAH

This study developed machine learning (ML) models for predicting rock formation reactive forces experienced by a hydraulic shovel bucket during excavation. To do this, rock formation in the form of muckpile was modeled as granular ball elements in three-dimensional particle flow code (PFC) using linear bonding logic. A typical field-size hydraulic shovel bucket modelled in AutoCAD was used to excavate the rock formation and the three-dimensional shovel bucket resistive forces required to cut through the rock formation were measured and recorded. The experiments involved different muckpile height, bulk densities, repose angles, and average fragment size. Six ML algorithms, artificial neural network (ANN), K-nearest neighbor (KNN), linear, random forest (RF), regression tree (RT), and support vector machine (SVM), were evaluated on their ability to predict the shovel bucket resistive forces. The input variables used for the prediction of the resistive forces were the muckpile bulk density, angle of repose, height, and fragment size. The results showed that the ML techniques are useful and reliable methods of predicting rock formation resistive forces based on the rock formation properties. This research is a preliminary step towards developing reliable models for accurate prediction of excavation forces/torques which could potentially enhance hydraulic shovel process automation.

Sep 27, 2021

By JESSICA W. A. AZURE, Samuel Frimpong, AZUPURI G. A. KABA, FORSYTH A. KADINGDI, PROSPER E. A. AYAWAH

The efficient and effective utilization of hydraulic excavators relies on, among other factors, a better understanding of the formation resistance during the excavation process. Studies on hydraulic shovel excavators have focused on optimizing the digging process by considering the reaction of the boom, stick and bucket, and analyzing the resulting moments at the shovel’s front-end joints. These studies failed to understand resistive forces from a statistical viewpoint. The purpose of this paper is to develop machine-learning models capable of predicting the formation of resistive forces during shovel excavation. The shovel’s excavation was simulated in the PFC 5.0 environment using a typical field-size hydraulic shovel bucket to generate the shovel contact forces required to overcome formation resistance

By Dengfu Chen, Mujun Long, Youguang Ma, Xin Xie, Xing Zhang, Leilei Zhang

"Processing parameters of a submerged entry nozzle (SEN) affect significantly on the patterns of fluid flow and temperature distribution in beam blank continuous casting mold with double SEN s. Effect of the geometry structure and immersion depth of double SEN s on the fluid flow in beam blank continuous casting mold was studied by water modeling. Results showed that, the optimal nozzle inner diameter was 40mm, and immersion depth was 70-90mm. The mold surface fluctuation, slag distribution, impact depth and removing rate of inclusion particles were discussed under different processing parameters of double SENs. As the results indicated, slag distribution was more non-homogeneous with a higher casting speed. The results provided basic data for the design and optimization of SENs used in beam blank continuous casting mold.IntroductionNear-net-shape casting has the distinct advantages of less rolling procedures, higher metal recovery and lower energy cost. Therefore, in the recent decades, one of the recent trends in the steel making process is moving toward near net shape casting. in which beam blank casting is a typical technology. The schematic section of beam blank is shown in Fig 1."

Jan 1, 2014

By Dwayne D. Tannant

This paper presents a new mining concept for oil sands called ?hydraulic underground mining of oil sands? or HUMOS. While this mining method is still at the conceptual stage it has great promise to allow extraction of bitumen from areas that are currently uneconomical or technically infeasible using surface mining or steam assisted gravity drainage. HUMOS is founded on a combination of recently proven technologies such as directional drilling, water jet cutting of oil sands, slurry transportation, cold water extraction of bitumen, and thickened tailings. One key component in the mining concept is the caving of oil sands and the creation of an underground cavern. Scaled-down physical models will be designed and built to demonstrate water jet cutting, cave development, and insitu primary bitumen separation. These will be used as a &apos;proof of concept&apos;. On-going research will establish and prioritize issues that need to be resolved, outline key areas where further research is needed, foster establishment of research teams to divide and conquer the important questions, and create framework for future coordinated research efforts.

May 1, 2001

By Carl W. Volz

NORWAY&apos;S metallurgical development, which has extended over many centuries, is intimately associated with that country&apos;s unique topography and climatic conditions. It is a rugged mountainous country, with a most irregular shore line, bordered by thousands of islands forming a natural protection for shipping. There are an endless number of lakes, and innumerable rivers and waterfalls, many fed by glaciers and melting snow. Rainfall is abundant. Though half of the country is north of the Arctic Circle, it is warmed by the Gulf Stream, so that the average temperature is about 45°, or 20° higher than other parts of the world in the same latitude. A sub-

Jan 1, 1935

By Max Hebgen

Within the State of Montana the streams rise in the high mountains at. an elevation of from 5,000 to 8,000 ft. These streams leave the State line both east and west at elevations from 3,500 to 2,400 ft. It is, therefore, apparent. that all these streams have an average fall of 3,000 ft. within the confines of the. State, and many opportunities are presented on all streams. for the development of power, by taking advantage of the natural fall. It is probable that 1,000,000 h. p. can :be developed in the State of Montana. I. NATURAL FEATURES OF STATE AFFECTING POWER DEVELOPMENT. The main. range of the Rocky mountains, forming the Continental Divide, cuts the State of Montana into two parts. The eastern part is drained by the Missouri river and its tributaries, the Madison; Jefferson, Gallatin and Yellowstone, rivers. The western part is drained by tributaries to the Columbia river, the Clarks fork and the Kootenai river. The Clarks fork in turn is formed by the junction of Missoula and Flathead rivers, the latter, draining Flathead lake. The western part of the State. is mountainous and the eastern part is comparatively level. As a natural result the rivers in the western part are capable of generating large amounts of power, while in the eastern part of the State natural power sites are much fewer and farther apart. It also follows that in the mountainous districts large amounts of power are required for the mining industry, while in the eastern part of the State, which is principally devoted to agriculture, power is required in smaller quantities. ?

Jan 8, 1913

By Zengjie Wang

Investigation on hydrochloric acid leaching of the ilmenite from Panzhihua, China was carried out to prepare synthetic rutile. The leaching parameters were optimized to obtain high content of TiO2 in the products. The experimental data suggest that an optimum leaching can be realized with 30% acid, a solid/liquid ratio of 1/4 at 95°C for 4h, and ore ground for -400 mesh size. After the acid leaching, an additional alkaline leaching process using hot NaOH solution was performed, and then the products was in grain form followed by heat treated at 900°C for 2h in order to extract Si and increase the particle size of synthetic rutile. The final product has a high content of TiO2 (about 95%), a low content of chlorine consuming elements (total CaO+MgO =0.07%) and a suitable particle size distribution for chlorination process.

Jan 1, 2008

By E Yll÷, O HyvSrinen

Outokumpu has developed a new chloride leach process, called HydroCopper«, to treat copper concentrates. Chalcopyrite is quite refractory in leaching and in sulfate milieu an autoclave of high temperature and pressure is required. However, in the HydroCopper«-process copper sulfides can effectively be leached in atmospheric pressure using strong, aggressive chloride solution and copper (II) ions as oxidant. Copper is precipitated from the purified pregnant leach solution as copper (I) oxide, which is filtered and reduced by hydrogen gas to metallic copper powder, which is melted and cast into copper product. Sodium chloride formed in precipitation is decomposed in a chlor-alkali electrolyser, the products of which are circulated back to the process: sodium hydroxide to copper (I) oxide precipitation, chlorine gas to leaching and hydrogen gas to the reduction of copper (I) oxide. During 2003 - 2004 the performance of the HydroCopper«-process was confirmed in a demonstration plant processing one tonne of copper per day. It has been found to be applicable for different kinds of concentrates and can also tolerate a wide range of impurities. A significant advantage of the process is that gold can be leached as a chloro-complex and recovered with active carbon. HydroCopper« can economically recover copper from concentrates and process to a cast copper product. The best utilisation of the process is in most cases achieved when the plant is situated at the mine site. Higher recoveries are attained by the optimisation of the whole operation chain from the mine and the concentrator to the HydroCopper« plant.

Jan 1, 2005

By W. Rubarth

The kaolin losses in hydrocyclone classification are determined by the fines, which are discharged together with the water to the underflow. This paper presents an improved technique of water injection to the conical part of the cyclone applied especially for small cyclones in kaolin preparation. In small hydrocyclones water, injection is a sensitive process. Therefore, the process was stabilized by controlled water injection dependent on the measurement of the underflow shape. Three applications of this innovation are presented. In the first case, the water injection is applied for the separation stage in dilute suspension where the final product is produced in the overflow of a 50mm hydrocyclone. The underflow contains sand and residual kaolin. For a higher kaolin recovery, the underflow is usually treated downstream in washing cyclones. The wash water injection results in a 45 ? 50% - reduction of the kaolin fraction <25µm in the underflow. Thus, water injection to the classifying cyclone leads to a separation comparable with a downstream washing stage. An additional hydrocyclone stage can be deleted. The second application refers to a classification in dense suspension. Here, the underflow of the last hydrocyclone stage was directed to a washing in a 50mm hydrocyclone. The additional injection of 3L/min water in to the conical part of the cyclone reduced the kaolin losses by half.The third application was executed in the washing stage equipped with 75mm hydrocyclones where the underflow is directed to flotation. Using the water injection the kaolin recovery in this stage was increased by approximately 20%. Keywords: hydrocyclone, classification, kaolin beneficiation, water injection, underflow washing

Sep 1, 2012

By K. Cole, D. Mesa, P. Brito-Parada, M. R. van Heerden

Turbulence in mechanical flotation cells, achieved via an impeller, plays a key role in keeping particles in suspension, dispersing air bubbles, and promoting particle-bubble collision. However, studying the hydrodynamics of a flotation cell is not a simple task, due to the complex nature of flotation systems which are opaque, turbulent, multiphase and polydisperse in terms of particle and bubble sizes. In this paper we study the impact of impeller design modifications on the hydrodynamics of a continuously overflowing bench-scale flotation tank. To this end, two different impeller designs, with and without a stator, were assessed using Positron Emission Particle Tracking (PEPT). This allowed the authors to determine, for the first time, the effect of an impeller design on the behaviour of both hydrophobic and hydrophilic particle tracers. It was experimentally observed that the use of a stator modifies the hydrodynamics within the flotation cell, distorting the lower mixing loop that is characteristic of axial impellers. The role of the stator in dissipating turbulence results in reduced particle velocities outside of the impeller-stator region. These results have important implications for flotation cell design and are discussed in the context of the impact that different designs have on particle movement, flotation hydrodynamics and, ultimately, flotation performance. The data set generated is also extremely valuable for modelling and validation purposes. Keywords: Flotation, flotation tank, impeller design, rotor, stator, PEPT, hydrodynamics

Jan 1, 2020

By Kevin Galvin, James Dickinson

"The Reflux Flotation Cell (RFC) consists of an inverted fluidized bubbly bed, located above a system of parallel inclined channels. This novel arrangement enhances the hydrodynamics of flotation in a number of ways. Firstly, the free-surface of the flotation cell is enclosed via a fluidized bed distributor, ensuring uniform application of wash water to promote desliming. Secondly, foams can be variable in their stability and lack permeability. Hence this system is preferably operated in the absence of foam, instead opting for a bubbly zone of high bubble volume fraction through the use of a very high gas flux and/or wash water flux. Discharge of the product proceeds upwards through a central port of narrow cross-sectional area. Thirdly, the system of inclined channels increases the segregation between the bubbles and the water, ensuring the bubbly zone remains contained within the upper vertical zone, and the liquid flux reporting to the overflow is low. The expanded operating regime of the RFC was investigated by covering a very broad range of gas fluxes, up to 5.5 cm/s, and wash water fluxes, over 2 cm/s. Both laboratory and pilot plant performances were quantified by the recovery of hydrophobic particles and rejection of the hydrophilic particles, using model and industrial coal feeds. The new system hydrodynamics was found to offer significant advantages in flotation kinetics, desliming, and particle recovery across a broad particle size range. Bubble interfacial flux reached as high as 600 m2/m-2s-1. The upper system consists entirely of a high volume fraction of bubbles, which provides a "safety-net" to protect against the detachment of coarse particles, and a highly permeable zone for counter-current washing of the flotation product. Under relatively extreme conditions selective stripping of the product is observed, resulting in grade recovery values beyond those achievable using the tree flotation method."

Jan 1, 2014

CSIRO Minerals, in association with the AJ Parker CRC for Hydrometallurgy, has an active program of hydrometallurgical research in which physical and computational modelling are used to better understand and improve a range of different unit operations. The modelling is based on flow simulation (Computational Fluid Dynamics or CFD), but incorporates other physical and chemical phenomena of importance, such as droplet break-up and coalescence, species transport and reaction. This paper reviews some of the major projects that have been undertaken at CSIRO Minerals and will illustrate the critical importance of hydrodynamics to the performance of unit operations and the improvements that can be made to performance using such modelling techniques. Unit operations that are discussed include solvent-extraction, gravity thickeners, flotation cells, bio-heap leaching and stirred tanks.

Jan 1, 2005

By C. E. Jordan

The U.S. Bureau of Mines investigated flotation hydrodynamics to improve the recovery of coarse phosphate. Fluid velocity profile measurements were used to characterize the hydrodynamics within commercial phosphate flotation cells and laboratory flotation cells. The effects of agitation, aeration, and pH on coarse phosphate recovery were measured in the laboratory flotation cells and correlated with the hydrodynamics measurements. Test results revealed that the agitation energy and aeration level had a significant effect upon flotation response. By optimizing these two parameters, 92 pct of the phosphate was recovered in a rougher flotation concentrate grading 28 pct P2O5?

Jan 1, 1994

By P. Songfack

In this work, the slurry flow in the ball mill is solved with Navier-Stokes&apos; equations and the marker and cell technique (MAC), which tracks the fluid-free surface. Considering different planes in the radial and axial directions, this numerical approach leads to the direct calculation of the slurry velocity profile, mill holdup, and volumetric flow in the ball charge and pool. The MAC technique takes as input, the results of a direct three-dimensional simulation of the motion of grinding media, and in turn, provides a detailed knowledge of the hydrodynamics of slurry flow through the porous structure of ball load. This technique is a new approach to the mass transport problem that overcomes the limitations of indirect studies such as residence time analysis and holdup measurements.

Jan 1, 1994