Search Documents

By Philip D. Anderson, Ralph Hultgren

Heat contents of extremely pure iron were measured over the range 300"to 1433"K, using a diphenyl ether calorimeter. Results from three samples containing widely differing impurities agreed with one another and with Previously reported results at higher temperatures (1184 ° to 1809°K) by Olette and Ferrier. From these data a table of heat contents of iron has been Prepared which is believed to be more accurate than those previously available. CP values have been derived which are consistent with these heat contents, with the best experimental Cp data, and with the thermodynamic conditions of equilibrium between bcc and fcc iron. The opinion is expressed that low-temperature extrapolations of presently known Cp values for y-Fe are not reliable. It would seem that the thermodynamic properties of iron, which is by far our most important metal, should have been well established long ago. This is not the case, however. As discussed by Olette and Ferrier,' there is objection to every earlier heat content measurement. While the best true Cp determinations agree well at temperatures below the Curie point, there is wide divergence at higher temperatures. Several investigators have examined available data and attempted to calculate thermodynamic functions for iron that are consistent with the two equilibrium temperatures of bcc and fcc iron. The two primary efforts were those of Austin' in 1930 and Darken and smith3 in 1948. The recommended values differ considerably; integration of Austin's Cp values leads to a heat content at 1100°K which is 300 cal per g-atom higher than the value recommended by Darken and Smith. The compilation of Fisher4 in 1949 was based on the selection of Austin. In 1956, Weiss and Tauer obtained yet another set of values by resolving Cp values into components due to dilation, lattice vibration, electronic excitation, and magnetism. The magnitude of contribution by each component and its dependence on temperature was estimated by semiempirical means. Their values are not self-consistent in that they do not form smooth curves when plotted vs temperature; moreover, their calculations cannot easily be repeated since they do not give the values of some of the parameters used. Clearly, experimental values for iron were in a most unsatisfactory state. The presently described measurements of the heat content of iron were therefore undertaken, covering temperatures as high as 1433°K. While the work was in progress, the high-temperature (1193" to 1789"K) heat content measurements of Olette and Ferrier' were published; in the region of temperature overlap the present results agree with Olette and Ferrier well within experimental accuracy. It is believed that the present results, combined with those of Olette and Ferrier, provide for the first time a reliable set of heat contents of iron from room temperature to the melting point. From these data, guided by available Cp measurements, it proved possible to derive Cp, entropy, and free energy function values for @-iron from room temperature to the melting point, and for y- iron in the temperature region of its stability. Exhaustive study led to the conclusion that extrapolations of y-iron functions to room temperature were not reliable enough to be useful; hence these have been omitted from the tables. EXPERIMENTAL Materials. Three samples of extremely high purity iron from different sources, containing widely different impurities, were measured. The first of these, designated "Chipman", was kindly supplied by Dr. K. K. Kelley of the U. S. Bureau of Mines from a lot which was made many years ago by Dr. John Chipman of the Massachusetts Institute of Technology. The second, designated6'Teddington", was supplied by the National Physical Laboratory, Teddington, England, from a lot zone-refined by them. The third sample, designated "Irsid", was supplied by the Institute de Recherches de la

Jan 1, 1962

By J. R. Vilelia

IN accordance with the custom of this society, we are gathered here, as we have every year since 1924, to honor the memory of the eminent American metallurgist and teacher, Professor Henry Marion Howe. Unlike many of the distinguished metallurgists who have preceded me as a Howe lecturer, I cannot bring to you reminiscences of his personality, for it was not my privilege to be associated with Professor Howe, or to be directly one of his students. Yet, Professor Howe and Professor Albert Sauveur, through the medium of their books, were my first teachers of metallography, as they have been of almost all American metallurgists of my generation. As a teacher, and for many years the acknowledged leader of American metallurgists, he exercised a profound influence in the growth of our science and was held in honor by the men of science of his time. I can speak no words of technical appreciation that will add luster to his fame, for by his prophetic vision, his teachings, and his researches he stands among the immortals in the memory of all metallurgists. In 1926, the third Howe Memorial Lecture was presented by Professor William Campbell' of Columbia University, who entitled it "Twenty-Five Years of Metallography." He took as a starting date for his chronology the turn of the century, which coincided with his arrival from England to work in association with Howe at the Columbia School of Mines. In that informative lecture Professor Campbell enumerated the important advances in metallography achieved during the first quarter of the century, and, it now appears, may have established the custom of reviewing such progress every twenty-five years. The scope of Professor Campbell's lecture was as broad as his metallurgical knowledge, for it embraced a wide portion of the field of metallography, both ferrous and nonferrous. Twenty-five years later, the Howe Memorial Lecture Committee saw fit to assign to me the honor of writing a lecture that would commemorate the work of Henry Marion Howe and would at the same time constitute the 25th anniversary of the lecture by Professor Campbell. The Committee suggested that this lecture might properly be called "Twenty-Five More Years of Metallography," a suggestion that I have adopted. I must confess, however, that I have not followed the precedent established by Campbell and have narrowed the scope of this lecture to an appraisal of those achievements which in my opinion have contributed most to the progress of microscopical metallography during the past twenty-five years. Progress in Metallography The metallographic methods most widely used today, with the exception of the electron microscope, were firmly established more than twenty-five years ago. In general, our specimens were prepared for microscopic examination in those days in much the same manner as they are today. It is true that new details of technique have been introduced from time to time, and that superior equipment is available today, but on the whole, these improvements have been in the nature of refinements, often a matter of personal preference, and none can be considered essential to the attainment of the ultimate goal of the art and science of metallography, which is to reveal the structure of metallic specimens with unequivocal clarity so that they may be interpreted correctly. Mechanical metallographic polishing, which was the only method available in 1926, is still universally practiced and still consists of abrading the metallic specimen with a series of abrasives of increasing fineness until a specular surface is attained. We have now the alternative method of electropolishing, but it is not widely used because, except in a few special cases, its results are inferior to those of competent mechanical polishing. Likewise, most of the etching reagents preferred today were in common use more than twenty-five years ago and were applied in the same manner as they are today. Valuable improvements have been made in the optical and mechanical performance of metallurgical microscopes, but there was no dearth in those days of excellent instruments equipped with achromatic and apochromatic objectives capable of yielding micrographs comparable in quality with the best that we can make today. In fact, it would be a difficult task for any metallographer today to make optical micrographs at magnifications in excess of 3000 diameters that would surpass those made by Lucas more than twenty-five years ago. One of these is shown in Fig. 1. Yet, it is unquestionable that on the whole, the micrographs appearing in the metallurgical literature today are vastly superior to those

Jan 1, 1952

By L. T. Sanchez, W. T. Rogers

This paper presents the results of a production experiment evaluating the effect of the use of oxygen in the bessemer converter with respect to its relation to blowing time, amount of steel scrap or cold pig iron which can be melted and teeming temperatures of the molten steel. THE simplest and probably the most efficient and economical means for producing steel from molten pig iron is the bessemer converter. This process is essentially a mechanism for bringing oxygen into contact with the molten metal thereby oxidizing the elements silicon, manganese, and carbon. The source of oxygen is that contained in the air and is limited by that amount. In theory, there is an intermediate chemical reaction due to the mass action of iron and air which is represented by the equation: 2Fe + O2- = 2Fe0 The FeO then becomes the oxidizing agent and reacts with the silicon, manganese, and carbon to produce silicon dioxide (SiO,), manganese oxide (MnO), and carbon monoxide (CO), in the order mentioned. The balancing of the various chemical reactions shows that in the ordinary bessemer process more than sufficient oxygen is delivered to satisfy these reactions, which indicates that a further increase in the oxygen content of the air would serve no useful purpose. In spite of this reasoning, however, it will be demonstrated that when melting stelel scrap, commercially pure industrial oxygen introduced into the normal air blast will permit the melting of a larger proportion of steel scrap than is possible with air alone and also will increase the production rate by a substantial reduction in blowing time. It will also be shown that when melting cold pig iron, it is possible to melt up to twice as much pig iron with the use of oxygen as can be melted without added oxygen with a nominal increase in blowing time. At the plant where this study was made, oxygen is purchased from a nearby supplier and piped directly into the plant. It is supplied to the bessemer converter by being introduced directly into the blast line through an automatic control system which may be adjusted by the bessemer operator or "blower." Normally, iron is supplied by five blast furnaces to an open hearth shop containing twelve 165-ton capacity stationary furnaces and a bessemer converting shop having three 30-ton converters. The molten metal from the blast furnaces is allocated to one shop or the other in a manner to best provide for maximum production. At various times, it is desirable to direct the maximum amount of available blast furnace production to the open hearth shop. This has the effect of reducing the production of the bessemer shop. When this condition exists, it is desirable to supplement the reduced iron charge at the bessemer with steel scrap or cold pig iron to the maximum possible extent in order to maintain high total ingot production. This condition becomes aggravated when one of the blast furnaces is taken out of production for any repair job and particularly for extended periods such as when relining is necessary. The purpose of the investigation and experimentation with oxygen was to determine whether or not it would contribute to increased flexibility in the use of the raw materials, molten iron, steel scrap, and cold pig iron. In addition to the effect of oxygen on flexibility of operation, it was also necessary to determine the relation of its use to production rate or "blowing time," final finishing temperature of the steel or "teeming temperature," and steel quality.

Jan 1, 1953

By J. Chipman

There is no better way of paying tribute to the memory of a scientist than by developing and carrying forward those ideas which he has contributed to science and which are for us the very essence of his immortality. For a lecturer who has not had the great privilege of stdying under Professor Howe or 'ven of knowing him in person, these ideas must be transmitted through the printed word. It is our great good fortune that Professor Howe left to us a rich heritage of publication, not only in his classic monograph on the "Metallography of Steel and Cast Iron" but in a wealth of earlier hooks and papers in the transactions of this Institute arid of other scientific and engineering bodies. An outstanding characteristic of this published record is the great breadth of interest and of vision which it portrays. His was riot a narrow specialization in only the scientific aspects of ferrous metallographg. On the contra1y many of his important contributions had to do with a far broader field of metallurgicial endeavor. He insisted that his students be well grounded in 1 he fundamentals underlying the whole field and not led into the narrow groove of specific applications. Among his first major publications we find papers on copper smelting, extraction of nickel, the efficiency of fans and blowers, thermic curves of blast furnaces, the cost, of coke, and the manufacture of steel. These are the papers of a metalhurgical engineer and it was among engineers that Henry Marion Howe made his early and well-merited reputation. These early engineering contributions display very clearly the strongly sctientific inclination of their author. The classic work on "The Metallurgy of Steel" published in 1890 contains a thorough and critical discussion of all that was known at the time concerning the alloys of iron and of what we would now call the physical metallurgy of steel. In addition it describes steel-making processes in use and some that had become obsolete, and points out in critical fashion the reasons for success and failure. Steel mill design and layout were included as well as some pertinent discussion of refractories. The book is indeed an embodiment of one of Howe's outstanding characteristics—breadth. It is both the science and the engineering of steel production as known in that day. One of Howe's earliest technical papers was entitled "What is Steel?" That was nearly seventy-five years ago when many new processes and new kinds of steel were being developed. The time was ripe for such a question and the answers which Howe was able to give were helpful in understanding the phenomena of heat treatment. Twenty-five years ago Professor Sauveur repeated the question as the title of the first Henry Marion Howe Memorial Lecture. It seemed to him that this question, "What is Steel?," had served as Howe's motto throughout the remainder of his life. Today I shall present for your consideration a question of another sort: "What is Sletallurgy?" Perhaps it is not too much to hope that in the answer we may obtain a clearer and possibly broader view of the nature of our science and our profession. The time is ripe for giving careful consideration to what we mean by metallurgy. If our Metals Branch is to become in fact an American institute of Metallurgical Engineers, it is essential that we understand what is meant by metallurgical engineering. I am convinced that the best interests of the profession have not been served by a narrow interpretation of these terms. We must now place emphasis on the breadth of metallurgy as a science and as an engineering profession. With its usual brevity and wit. Webster's dictionary definesmetallurgy as "the science and art of extracting metals from their ores, refining them and preparing them for use." I shall riot assume that the words "science" and "art" and "metal" are so well understood as to require no defining but others among our contemporaries are better qualified than either your lecturer or the dictionary to present the broad meanings of these terms. When we say that metallurgy is among the oldest of the arts we are not classing it with painting or sculpture or music but rather with the making of tools or weapons or the building of bridges or chariots or cathedrals. In short we are saying that metallurgy is among the oldest of the engineering professions. The question " What is metallurg ? " has been one of rather more than ordinary concern to those of us who have the task of developing a curriculum for the education of students in this field. This development has been going on in a number of universities over a period of some years. but there seems to be as yet no unanimity as to what such a curriculum should contain. I believe there is fairly complete agreement that it must be founded upon sound

Jan 1, 1950

By AIME AIME

BEFORE proceeding with the papers scheduled for the ore and foundry session*, the teller's report on the election of officers for the ensuing year was presented, a; follows: Chairman. G.C. F. MacKenzie; vice-chairmen, C.S. Robinson, J. T. MacKenzzie, C. E. Meissner; executive committee, A. L. Field, R. F. Harrington, E. F. Kenney lit. Waterhouse announced that the fall meeting will be devoted to alloy steel. This meeting will be held in Chicago the week of Sept. 22 in connection with the National Metal Congress. He also announced that oxygen in steel will be the central idea of the meeting which will be held in New York next February. The first paper, entitled "Sintering Limonitic Iron Ore at Ironton, Minn.," was presented by Perry G. Harrison (T. P. 284), the author. Sintering was first un¬dertaken in 1024 to treat Cuyuna range iron and manganiferous ores low in silica and high in moisture and containing objectionable qualities of fine... A Dwight-Lloyd machine was first installed. This machine was replaced by a larger one having a width of 72 in. The power cost was decreased from about $11.22 per ton of sinter on a 42-in. machine to about X0.14 for the 72-in. machine. The tons of sinter per man-shift was increased from 11.86 to 16.77. Improvements embodied in the larger plant reduced the cost of sintering to $0.41. The analyses of iron ore and manganiferous ore and the sinter produced from these materials was used to show the increase in value at the mine resulting from sintering. Crude iron ore actually unsalable was increased in value f.o.b. mine from a theoretical figure

Jan 1, 1930

By F. N. Speller

ASIDE from the Tuesday symposium on gases in metals, the Iron and Steel Division swung into action for the first time on the third day of the meeting with a discussion of iron and steel alloys. Dr. E. S. Davenport opened the discussion on Wednesday morning by presenting the paper written by himself in association with E. C. Bain and W. S. N. wiring on the equilibrium diagram of iron-manganese-carbon alloys. A written discussion by Mr. Scott showed qualitative agree- ment, but some quantitative disagreement. Messrs. Marsh and Sisco discussed the paper at length, pointing out non- agreement of certain conclusions with the phase rule. Dr. Krivobok, although differing with the authors on some points, stated that in his opinion the information collected would be valuable in the practical use of these alloys.

Jan 1, 1932

THE annual meeting of the Lake Superior Mining Institute was held on Sept. 7 and 8, Crystal Falls and Iron Mountain, Mich., being the principal centers of activity. Members of both institutes began assembling early, and by the evening of Sept. 6, some 60 had already arrived at Crystal Falls. The greater number arrived the following morning, however, and after the usual formalities of registration were attended to, the party were loaded into automobiles and set out on a tour of inspection of the mines near Iron River; some properties were passed through, and some were briefly visited to permit the inspection of any unusually interesting piece of equipment or detail of practice. The last stop of the morning was at the Caspian, Iron River, where the entire party was entertained at luncheon at the Caspian Club House. Both the food and the company were excellent, and as the weather was superlatively good (though the natives of the district modestly declared it was only ordinary autumn weather) the lunch was served on the lawn at the rear of the club, where the green turf, abundant flowers, and music by the band, added to the charm of good fellowship. The degree to which mining men have become addicted to golf was indicated by the large number of plus fours in evidence, whose wearers appeared just before lunch and disappeared immediately afterward.

Jan 1, 1928

By A. B. Kinzel

THE year 1936 has been an eventful one in the iron and steel industry. Renewed industrial activity has brought with it many new problems. These problems have generally involved the question of increasing capacity without sacrifice of economies and quality developed in the less active previous years. The nature of the iron ore used and the effect of its porosity and other physical characteristics on the capacity of the blast furnace has been reviewed by the U. S. Bureau of Mines. The whole question of handling raw materials and methods of charging furnaces has been intensively studied, with the result that capacity has been in- creased without affecting the quality of

Jan 1, 1937

By AIME AIME

THE week, of April 5 will long be remembered by those that attended the Birmingham meetings of the Open-Hearth and Blast Furnace committees of the A.I.M.E. Iron and Steel Division. Birmingham iron and steel own received the 450 delegates with open arms; described and discussed their southern metallurgical practices and problems and compared experiences with their northern brother metallurgists in two days of technical sessions on Wednes-

Jan 1, 1937

By John Johnston

THIS necessarily brief sketch will attempt to summarize the high lights of perhaps the best meeting so far held by the Iron and Steel Division. All sessions were well attended and the discussion was vigorous and of a high order. The technical sessions opened. on Tuesday morning. "Precipitation Hardening of Copper Steels" was discussed by Cyril S. Smith and Earl W. Palmer, and dealt with steel with a 1 per cent copper content. Discussion brought out that there were no fabricating difficulties, but that the surface might be somewhat checked due to intergranular penetration of copper which could be easily taken care of. Probable advantages of steels of this type for high temperatures were pointed out. "An Improved Nickel-chromium Hardened Chilled Cast Iron," by J. S. Vanick, described a wear-resistant cast iron and evoked a lively discussion.

Jan 1, 1933

By Clyde E. Williams, JAMES L. GREGG

THIS review of the past year's progress in iron and steel metallurgy presents examples of only a few of the interesting or important accomplishments made in the United States. In the field of iron ore concentration increased attention was given to the study of the more difficultly separated wash ores and some progress was made in tabling. One difficulty with the table, in concentrating iron ore where the percentage of concentrate in the feed is large, has been the removal of fine silica from the thick layer .of concentrates in the cleaning zone. One company has -Made an important contribution toward the solution of this problem by an extension of the well-known plateau principle. By a special riffling of the plateau section of the table, the concentrates are crowded together. This action forces the fine silica to the top of the bed in the cleaning zone, whence the cross-flowing currents of water -can wash it into the middling product. Some work has been done on the application of froth flotation to the concentration of iron ores. Laboratory experiments were made at the Colorado School of Mines in which hematite was, successfully floated. Using oleic acid as a frothing and collecting agent and sodium carbonate as the conditioning agent, a high recovery of rich ,concentrate was obtained. A laboratory flotation unit is in use at Taconite, on the Mesabi range, and a commer-

Jan 1, 1932

By G. B. WATERHOUSE

THE year 1929 was exceedingly busy and prosperous for the iron and steel industry in the United States. The lake shipments of ore were approximately 65,000,000 tons, steel ingots produced were about 57,000,000 tons. Plants were very active. operating for many months well over their rated capacity, slowing down during the last quarter following the severe break in the stock market. The ore tonnage mentioned above was the greatest ever shipped by lake from the Lake Superior region. The trend at the ore mines has been to supplement manual labor by mechanical appliances as much as possible. Mining methods have been greatly improved along the lines of safety as well as to increase the percentage of ore recovery. Crushing and grading of iron ores continued to gain in popularity inasmuch as remarkable blast-furnace operations and records were obtained with sizing and uniformity of raw materials. Progress was made along other lines. The Bradley process for the separation of manganese osicle and iron oside from siliceous manganiferous iron ore was cleuelopecl; also considerable work was clone on a process for the beneficiation of the Cuban laterite ores. Sintering of ores and concentrates increased in popularity. A new analytical method for the deter- mination of sulfur in iron ore was worked out which reduced the time required appreciably. The ore re- serves of the Lake Superior district continued to receive considerable attention and played an important part in the recent mergers which have taken place in the iron ancl steel industry.

Jan 1, 1930

By Clyde E. Williams

THIS review of the progress made in iron and steel metallurgy during the past year is confined to developments in this country. It attempts to give examples to illustrate progress made rather than to appraise results. As a result of the gradually diminishing supply of rich iron ores and of predictions made as to the probable life of the iron-ore reserves of the Lake Superior District, attention of iron and steel executives was directed to the question of beneficiation of iron ores. Laboratory and plant-scale experimental work was conducted on the wash ores .of Minnesota and an investigation, was, begun on the Old Range low-grade ores.

Jan 1, 1931

By Horst Konig

This paper illustrates that, with the application of new processes, smaller steel plants using local raw materials can be economical and advisable. It also introduces the problems connected with the direct reduction processes, which use non-coking coal or gas as reducing agents, and which are employed in connection with conventional reduction to produce excellent results. Electric smelting is also discussed, and some practical examples of operating plants are given.

Jan 1, 1970

By Juergen Antrekowitsch, Stefan Steinlechner

"Waelz oxide from steel mill dust recycling is usually sold to the primary zinc industry, where it is first charged to the roasters to eliminate the remaining fluorides and chlorides. This limits the overall amount of secondary materials which can be used because of different operating problems in the roasters. Another option, in the case where the halides are low, would be direct leaching with low or medium concentrated sulphuric acid. Unfortunately, because of the carryover of some steel mill dust, iron is also present in the Waelz oxide, reaching contents up to 5 wt.%. Since the objective is to treat the solution more or less directly by electrowinning, with only a few simple preliminary purification steps, iron in the solution is a very important factor. Various trials have been done to investigate the dissolution behavior of the iron contained in the Waelz oxide. Although the zinc extraction should reach a maximum, all other elements, especially iron, should be low. This paper describes the results of our research in this area and offers possible options for Waelz oxide utilization. There is also a focus on how other elements, present in the material, influence the dissolution behaviour of zinc and iron, and whether a loss of zinc is unavoidable, if low iron dissolution is required.INTRODUCTION One of the most important secondary zinc resources is the zinc oxide originating from steel mill dust recycling. For the treatment of high zinc containing steel mill dusts, the Waelz kiln process is the so called “best available technology” and it dominates the industry, with roughly a 90% market share. The product Waelz oxide contains mostly zinc oxide, but it also contains lead compounds and halides due to evaporation with the zinc. In addition, it contains iron and some slag compounds due to mechanical carry-over. The presence of halides limits the use of the material as an alternative concentrate for primary zinc electrowinning. Such halides can be reduced to a certain extent by washing and/or solvent extraction (see following chapter). Although lead is not troublesome and theoretically represents a second recoverable valuable metal, iron is unwanted and causes additional problems during leaching. Even though Waelz oxide is generally a highly welcome input material in primary zinc metallurgy, due to its high zinc content, it still contains halides, and in the majority of cases, the oxide must first be treated in a roasting process. Different circumstances, like accretion formation because of the lead and halogen compounds as well as unwanted cooling effects in the roaster, limit the amount of Waelz oxide which can be substituted for the primary concentrate. Another, even more limiting factor, is the allowable concentrations of chlorides and fluorides in zinc electrowinning, the last step in the primary zinc processing route (Ruetten, 2011)."

Jan 1, 2016

By G. W. Josephson

WHILE methods of utilizing blast-furnace slag have been developing, a great deal of literature on the subject has accumulated, but no comprehensive summary of information that would be helpful to engineers, contractors, architects, chemists, and others in under-standing and more successfully using this byproduct of the iron and steel industry has been published in the English language. The National Slag Association recognized the need for such a publication, and the Problems Committee of the Association under-took in 1943 to accumulate the necessary material. Over a period of several years this committee compiled pertinent information in manuscript form, and in 1948 the Bureau of Mines and the National Slag Association made an agreement whereby the Bureau was to prepare the data for publication as a cooperative bulletin of the Bureau of Mines and the National Slag Association.

Jan 1, 1949

By W. H. Caruthers

ECONOMIC utilization of all by-products has long been the goal of American industry. One of the first groups that was popularly supposed to have achieved its aim was the meat-packing industry, which reputedly found a use for everything except the squeal of the hog. To the metallurgist, slag has always been the principal wasted by-product, representing a loss not only of material, but of heat. Slag does not possess many qualities that appeal to man's imagination or suggest a romantic influence on the daily life and progress of a community or nation. It is a bulky product, and space for its disposal within reasonable hauling distance of a smelter is not always available; the iron-ore smelter especially has been wont to find space for slag disposal at a premium. Therefore, the success that has been attained in recent years in finding a use for iron blast-furnace slag is notable. It has become a vital economic factor in the construction industry in areas where it is available. Its use may suggest further possibilities of an economic outlet for the slags from nonferrous smelting as well.

Jan 1, 1940

By J. E. Rehder

IN A DISCUSSION of use of any material of ?construction in the mining industry, two points of view must 'be kept in mind - that of the producer or manufacturer of mining and metallurgical equipment, and that of the maintenance and operating staff of the mining plant. In the first case, the choice of material of construction is up to the manufacturer and the user of the equipment has little direct say in the matter. However, if materials are badly chosen and the equipment does not function properly, wears out rapidly, or costs too much, repeat orders ?will likely go to a different manufacturer, so that, in the end, the consumer or mine operator does have the final voice. In the case of materials for maintenance work and plant operations, however, .the mill personnel have direct control over purchases and it is then that a well-balanced knowledge of materials, their properties, and their costs, can be directly useful. With all materials of construction, the final criterion is unit cost versus service performance, so that the lowest possible total operational cost will be obtained. Sometimes this means using the cheapest material available, sometimes the most expensive, but in any case careful analysis of service performance, replacement cost, and material cost is essential to determining the material that produces lowest total cost.

Jan 1, 1956

During the hydrometallurgical processing of the major base metals Cu, Zn, Ni and Co, the presence of iron is normally a serious complication, and iron separation from the pay metals usually constitutes one of the main challenges for the metallurgist. There are many instances, however, where the presence of iron is beneficial, or is even required. Two cases are presented where iron is required during the processing of base metals. The first example deals with the use of ferric sulphate to oxidize sulphides, more particularly copper and zinc sulphides, under atmospheric conditions. The results presented confirm that ferric ion leaching is efficient, particularly when the oxidant is regenerated during the process. The second case is the use of iron to solubilise refractory cobalt oxide minerals; examples, including pilot plant results, are presented for various ores from Africa and Central America. In both cases, this paper reviews the basic concepts involved and provides details of their application.

Jan 1, 2006

By J. A. Finch

For base metal sulphides, iron rejection starts in mineral processing. This review focuses on the changes in plant practice specifically to improve iron sulphide rejection by controlling contaminant ion effects and discusses selected innovations in mineral processing that can be expected to play a role in iron control. One change to control contaminant ions is size reduction (the use of stage grinding and inert stirred milling) and another is system chemistry (order of reagent addition and exploitation of the flexibility of sulphoxy species). Plant examples illustrate the successes, and indicate that there are several options available. The general innovations consider the new tools for measuring gas dispersion properties and quantifying froth characteristics from images. Examples of their application to improve concentrate quality illustrate the potential. Other innovations adapt geostatistics to model variations in ore flotation response to provide feed forward control and rigorously apply the statistical experimental methodology in plant test work. An example from one concentrator shows that significant improvements to reduce the iron content of concentrates can be achieved by applying these basic principles.

Jan 1, 2006