Search Documents

By S. Ramatsoma, D. N. C. Phillpotts, B. Whitehead

Changes in flotation performance have been correlated to changes in froth structure, velocity and stability. Literature has shown that when the aeration rate is varied for a specific float cell, the recovery of the valuable mineral reaches a peak which also coincides with a peak in the air recovery – a measure of froth stability. Peak air recovery optimisation methodology is a way to use direct readings of physical phenomena by froth cameras to optimise the metallurgical performance of a flotation plant. The aim of this paper is to show the transient nature of the peak air recovery value and the variety of conditions required to attain the peak air recovery on an industrial flotation plant with tight base-layer control of the feed and internal conditions. Industrial site tests that were conducted under controlled conditions showed different peak values at significantly different corresponding aeration rates during normal operation. The measured peak air recovery points corresponded to maximum PGM recovery during normal flotation, as expected. This dynamic nature of the peak air recovery point conditions has not previously been discussed in literature and indicates the need for online measuring equipment and informs the design of process control algorithms required to exploit the phenomenon for optimisation. Keywords: Froth flotation, flotation control, flotation optimisation, peak air recovery

Jan 1, 2020

By F. Charette

Instrumentation has been developed that can monitor the strain applied to a D-Bolt up to 7.5% elongation. The technology far exceeds the limit for foil resistance strain gauges. In the laboratory the instrumentation has provided insight into the fundamental behaviour of the D-Bolt following yield. Currently the instrumentation is undergoing field trials at a number of Canadian Mines. Discussion on field results is provided with regards to significance, reliability and temperature effects.

Aug 1, 2013

By Todd Minoski, KRISTIN FLOYD, Michael Murphy, VASU GANGRADE, Gamal Rashed, DYKE MARK VAN, Brent Slaker

Underground stone mines frequently operate on multiple mining horizons or are required to undermine or overmine old workings. In these situations, the effects of pillar columnization and interburden thickness on the stresses surrounding mine workings are poorly understood. Many old workings were not designed to consider the effect on future undermining or overmining and, as a result, are laid out on irregular patterns and with pillar sizes that are difficult or impossible to replicate on adjacent levels. Additionally, as depth increases, even a consistent gridded mine layout may result in poor columnization due to the need to increase pillar sizes. Rules of thumb and past practice for designing multiple levels may often be effective. This paper explores the effect that multiple-level stone mining has on stress redistribution through the discussion of two case-study mines and associated numerical modeling to provide additional insight into situations which may cause concern.

By A. A. Remes

High precision on-line particle size distribution measurement of mineral slurries has recently be-come available. It provides new tools for the development of monitoring and optimization methods for mineral grinding and separation circuits. The paper presents the development work at the Kemi chromite concentrator plant of Outokumpu Tornio Works in Northern Finland. The Kemi concentrator processes annually 1.2 Mt of chromium ore. The products are upgraded lumpy ore and metallurgical grade concentrate. The concentrate is produced using gravity separation methods, preceded by a rod mill - ball mill grinding stage. The separation process performance is strongly dependent on the particle size distribution of the grinding product at the Kemi plant. Particle size distribution has a significant effect on the concentrate grade and recovery. Currently a new laser diffraction based on-line particle size analyser is used for monitoring the grinding product. The analyser system allows the measurement of the whole cumulative particle size distribution simultaneously. It provides a wealth of new measurement information for process control. A monitoring and optimization scheme for grinding and gravity separation based on the particle size information is presented. The goal is to minimize the production of fine slime, and subsequently to improve the concentrate quality and minimize chromite recovery losses. Data-based recursively identified linear PLS process models are developed for optimization purposes. The preliminary results of the monitoring system operation in on-line use are presented.

Jan 1, 2014

By James JV, Petho SZ

The South Deep surface shaft system is being sunk to a final depth of 2750 in below surface and on completion will be the deepest single drop haft in the world. The shafts will intersect the target reef horizon at 2650 to below surface. In order to negate the requirement for a shaft pillar, which would he extremely large at this depth, the reef horizon in the vicinity of the intersection is currently being mined. A high quality crushed waste/classified tailings backfill is being placed in the longwall stoping panels around the shaft intersection area. This kill limit closure and ride which following shaft reef intersection could have a detrimental effect on the long term shaft stability. This paper discusses underground instrumentation results and numerical modelling exercises carried out to confirm that the shaft system will he stable throughout the life of the mine. Instrumentation projects include closure and ride measured between backfill paddocks and haulage leveling exercises carried out to determine the far field rockmass response to mining with stiff backfill.

Jan 1, 1998

By L. Xingwana

"The purpose of this study is to understand how ore loss and dilution affect the mine call factor, with the aim of subsequently improving the quality of ore mined and fed to the mill. It was necessary to know the relationship between ore mined and delivered for processing in order for the mine to operate efficiently. A review of the literature suggested the mine-to-mill integration approach as a standard intervention to address declining mine call factors. A case study was undertaken at a gold mine in the Free State on the influence of the fragment size distribution on ‘free gold’, the effect of ore loss and dilution on the mill efficiency, and time tracking of ore movement from source to the plant. The study revealed that fragmentation, underground accumulation of ore, and dilution have a significant influence on the mine call factor and mine output. It was difficult to quantify the total ore loss due to the time lag between mining and milling, which is extremely variable, when estimating the mine process inventory. However, it was possible to estimate the total dilution with some degree of precision by analysing the daily blast and head grades. It is therefore recommended that mines accept that some gold loss and dilution will always occur during blasting and transport of broken ore, and this loss must be minimized.IntroductionThe mining of high gold grades is obviously very beneficial for the economic viability of an operation, but optimum recovery of the product is required to maximize profits (Chapman and Bindoff, 2010, p. 13). Although integrating these two requirements is very difficult, due to the various activities occurring between mining and processing, it is indispensable. The main driver of this integration is the impact that different ore types and characteristics have on head grade. According to Isokangas et al. (2012, p. 871), mining and processing operations involve a series of well-defined sequential stages that are complementary in an efficiently operating mine, with the performance of one operation affecting that of another. An attempt to optimize each function separately without considering the whole extraction process will not result in the optimum efficiency of the entire mine. Several researchers have developed a proven methodology for revealing these inefficiencies (Dance et al., 2006, p. 1)."

Jan 1, 2016

By K. Mirkhani, P. Gebski, W. Ying

The campaign life of an industrial metallurgical vessels strongly relies on the quality and quantity of the refractory lining. An operating furnace or converter refractory lining can be assessed either by thermal modeling or by acousto ultrasonic-echo (AU-E) technique or a combination. AU-E is a Non-Destructive Testing (NDT) stress wave propagation technique that has been utilized on a wide variety of smelting vessels for over 12 years with good success. AU-E can determine the thickness of remaining refractory lining, estimate the thickness of build-up or accretion, detect and locate metal penetration and impregnation into the lining, and identify hydrated or cracked areas of refractory. This paper details the AU-E principles, equipment and recent improvements to the data analysis to further improve speed and accuracy. In addition, the paper discusses the AU-E accuracy and limitations through a diverse and vast array of practical examples including a comparison with thermal modeling and physical measurements.

Jan 1, 2011

By Bruce Macdonald

Operational monitoring of slope stability can be achieved by space based InSAR monitoring platforms. Natural and man-made rock slopes are monitored using a novel stack-based InSAR method that exploits both persistent point scatterers (PS) as well as coherent distributed scatterers (DS) such as areas of pavement and sparsely vegetated surfaces. The new method, Homogenous Distributed Scatterer (HDS)-InSAR identifies InSAR targets by using adaptive multilooking of statistically homogenous pixel neighbourhoods combined with thresholding the differential temporal coherence of each target candidate with respect to its surroundings. HDS-InSAR preserves PS and therefore forms a direct generalization to our proven DualScale-PSI method. The density of HDS exceeds that of PS by more than an order of magnitude often providing essentially continuous coverage over urban and industrial landscapes featuring a mix of infrastructure with mostly bare soils or rock surfaces. The improved coverage enables better definition of surface motion and underlying geology, which will lead to superior interpretation of the geophysical mechanisms causing the surface deformation, e.g. through improved integration with 3D deformation modeling. We illustrate the performance of our new HDS-InSAR method compared to DualScale-PSI using displacement results from Vancouver, Canada; Bingham mine, USA; and the Palabora mine, South Africa.

Jun 1, 2012

By Allan Gebhard

The purpose of this paper is to summarize the role of water resource monitoring in mining activities and to discuss the considerations that go into designing and implementing a monitoring program. The design of a monitoring program is invariably based on sound engineering and scientific judgement since no design formulas exist that can be universlly applied to the monitoring of all activities. As discussed in this paper, however, a methodology of designing a water resource monitoring program does exist. In order to cost-effectively monitor the water resource impacts of mining activities, the following three monitoring related items should be understood: 1. the role of water resource monitoring in the planning, construction, and operational stages of mine development, 2. the available water resources monitoring methods and the proper role of each method in the various scages of mine development, and 3. the strategies that should be followed in designing and implementing a water resource monitoring program.

Jan 1, 1976

By M. Hopf

Numerous developments and improvements have been made to tap-hole designs. On the other hand, there are very specific designs in operation that have endured for many years without any modification. Nobody likes design changes because of risk - the risk of atypical wear, potential hazards, and costly repairs entailing enormous production losses. So the philosophy ‘never touch a running system’ is maintained, because among other things there is no efficient working monitoring technology for tap-holes. In the past few years a couple of new technical solutions have been investigated and developed. Not all theoretical solutions are possible in practice. However, metallurgists are inventive, and the last word regarding efficient working tap-hole monitoring technologies has not yet been spoken.

Jan 1, 2014

By M. U. Oko

"Monitoring of all the waste streams from Falconbridge's Sudbury Operations to determine whether they meet the required standards, has been performed for many years. By 1969, however, the number of samples being collected had become so large that a complete revision of the existing systemwas necessary. Sites previously designated by name only, were numbered, clearly marked on the ground and on maps which were circulated to all concerned. The types of pollutants analyzed were determined and specified for each sampling location and a chemical analysis report form was designed. The sampling schedule has been computerized to produce a periodic listing of the samples to be taken and the analyses required.An area map showing sampling sites, chemical analysis report form, spill report and a computer print-out example are shown and explained.EVOLUTION OF FALCONBRIDGE'S WASTEWATER. MANAGMENT SYSTEMFalconbridge Nickel Mines employs some 4500 people, operates nine mines, four mills and a smelter in the Sudbury basin. The operations are geographically fragmented into four widely separated locations, the Falconbridge operations east of Sudbury and the Onaping operations in Levack Township being the two largest of the four. The Lockerby area located to the west and the Lindsley Mine just north of Sudbury are now under development. The magnitude, the diversity and nature of the operations are such that constant vigilance is needed to prevent inadvertent damage to the environment. The purpose of this paper is to describe the information system used to monitor and control waste-water disposal on Falconbridge's properties to help ensure the maintenance of effluent standards satisfactory to the Ontario Water Resources Commission (OWRC) and to the Ontario Department of Health."

Jan 1, 1971

By T Vijayakumar, Vipul Dobhada, Rajesh Patel, Swarnadip Dey, Naveen Babu D

The most challenging scope of any bridge project in marine or inter tidal zone is to construct sub structure like well Foundation, group pile, pile cap etc. Similarly, it also affects the marine environment/ecology to a great extent. Understanding the level of difficulties and aiding to provide an environment friendly solution, various options are analysed to overcome these and found mono pile to be the best alternative in this context. Generally, the foundation type of any bridge constructed in river, marine or intertidal zone in India is preferred for group piles. For the first time, monopile is being accepted as the foundation of bridge in India at Mumbai Coastal Road Project. The diameters of the monopiles used in this project are 2.5 m and 3.2 m. Hence, the challenges involved in monopile construction and experiences to overcome it are worth to share. Here, a brief discussion on environmental, geological issues and the needs of monopile as the foundation of bridge has been discussed. Furthermore, the monopile construction stages and confirmation of monopile capacity through different load tests have been elaborated.

Sep 1, 2022

By B Besa

Australia is a world leader in the design and operation of mines accessed by the decline method. Literature indicates that a number of metalliferous underground mines using the decline system are also increasing steadily. This increase has generated a great deal of interest in underground haulage systems in future due to the huge costs involved in the development of declines. Studies have also shown that the current method of accessing orebodies by the conventional decline method has proved to be expensive, especially for narrow vein deposits. This is because decline development costs are influenced by mine planning and design parameters as well as available haulage systems that the mining engineer can choose from. The current access method suggests that more waste material is being extracted because of the size of decline openings adopted (5.5 mW and 5.5 mH). Also the conventional 1:7 decline gradient and turning radius of 20 m makes decline lengths, as well as the duration of development, excessively longer. This paper discusses results of a mine design case study with monorail technology as a method of accessing and developing the decline. The proposed system is economical, has high advance rates and offers a significant reduction in capital expenditure. The study compares costs, development metres and the duration of decline development using the monorail system with the conventional (truck haulage) access method. Results obtained indicate that the monorail technology has the potential to reduce the decline length by over 62.6 per cent and decline costs by 63 per cent for the case study. The monorail system also reduces the total capital development costs by 22 per cent for the same case study. Due to rapid development resulting from increased advance rates and the shorter decline length coupled with smaller decline openings, the time to access the deposit reduced by 71.8 per cent. This case study demonstrates that the economics of narrow vein deposits can be improved significantly by using the monorail system of decline development.

Jan 1, 2008

By Braden Lusk

Vibrations as a result of blasting practices in mining engineering are a complex phenomenon controlled by many variables. Mine blast vibration modeling and prediction is becoming more important as a consequence of interactions by mining activity with an ever closer public. Many communities (all over the world) close to mining activity often complain about airblast and vibrations produced from blasting activity. It is important for the mining industry to have tools and understandable methodologies to model and predict blast vibration. These tools can then be used to predict and control vibration at neighboring structures.

Jan 1, 2013

By K. Verghese

Neutron capture prompt gamma-ray analysis provides the best method for on-line analysis of the elemental composition of large volumes of bulk material. This paper summarizes the Monte Carlo models which simulate the radiation transport within two such analyzer systems; namely, the borehole configuration and the conveyor belt configuration. The models are useful in the design optimization of the analyzer systems, in minimizing the amount of experimental calibration data for calibrating these analyzers, and in investigating the detection sensitivity for different elements. The computational scheme in these models is made extremely efficient by the use of various powerful variance reduction methods and by efficient data management. Experimental verifications of the two models carried out in the laboratory indicate very good agreement with the Monte Carlo results.

Jan 1, 1984

THE first session of the Institute was held on Tuesday evening, September 16th, in the William Molson Hall, of McGill University, Dr. T. Sterry Hunt, Chairman of the Local Committee of Arrangements, in the chair. Dr. Hunt introduced Monsieur S. Rivard, Mayor of Montreal, who spoke as follows : GENTLEMEN: We welcome you with pleasure to our city, and we are proud to find that you have deemed it worthy of your visit. I understand that your association was founded in 1871 with some thirty courageous members, and that so valuable has it been esteemed, and so attractive was it found, that nearly one thousand have now enrolled their names as members and associates. But we must regard your profession as dating back to the stone age and mingling therewith ; how remote that is none of us can tell. Much of civilization is due to the discovery of metals, and the magnitude of our works to their widespread abundance. If you have not accomplished what the alchemists aimed at, which was to turn the ruder materials into gold, you manage, by your subtle skill, to turn stones into gold value. Europe has long since been-dug into and perforated with shafts and galleries in search of metals, and great wealth, and power, and comfort have arisen there-from ; but by an increase of knowledge, and more than European enterprise and energy, America is following rapidly in the race, and by means of natural advantages of a geological character has out-stripped the Old World. We are pleased to see you, gentlemen, as an evidence of the unity of this continent. Maps may have various delineations, but the veins and arteries of commerce and the nerves of science knit all together into one social organism with the same vital functions. We live here on the margin of the world, and can claim but a modest share in. the great works of modern times, but such as we have that can interest you we gladly offer for your observation.' Our Victoria Bridge may he considered appropriate, for without mining engineers to precede the civil and mechanical, no bridge would be there to-day. In truth, the same may be said of all works of metal, and of all that are executed by tools and machinery made of metal. The Mont

Jan 1, 1880

Jan 1, 1880

By John A. Church

Jan 1, 1880

By James P. Kimball

Sulphur is always present in mineral coal of every variety. In the oxidized state it may exist as sulphuric acid in combination with a base. In the unoxidized state it exists in combination with iron as bisulphide of iron. It is also supposed by some chemists to exist in unknown combinations with the organic elements of the coal. This supposition requires the demonstration as a fact that certain coals yield more sulphur than what may exist in a free state, or what belongs to recognized combinations, not only with the accompanying iron but with other inorganic bases abundantly occurring in coals, but which unfortunately are very rarely estimated. This practically as well as theoretically important question it is at present impossible to decide, simply for want of available thorough ultimate coal analyses including the ash. Such analyses, at the best imperfect, are luborious and intricate, and therefore seldom made, the much simpler proximate analyses, so-called, being resorted to by most chemists for technical purposes, and commonly substituted for more scientific work even in the laboratories of government surveys. And it is unfortunate enough that few ultimate analyses are extended to the composition of the ash, much less to its relation to the original constitution of the coal. Sulphur chiefly occurs in most coals in the form of yellow pyrites (pyrite) and white pyrites (marcasite), both minerals, characterized by differences in crystalline form and in physical properties as well as in color, but having the same chemical composition (FeS2). No coal is entirely free from one or both of these dimorphous forms of bisulphide of iron. It may be disseminated through the mass so as to be invisible, in plates or scales between the laminæ of the coal, or in conspicuous segregations or nodules, sometimes of considerable dimensions. Coals greatly differ as to the proportion of sulphur which they contain. They also differ as to the relative proportion in which its several forms of combination occur. Such qualitative and qnantitative disparities arc scarcely, if at all, more marked in separate coal seams of a uniform type than in different parts of one and the same coal seam, whether it be considered locally as constituted of several

Jan 1, 1880

By S. Fisher Morris

The New River coal-field embraces that portion of the Appalachian coal formation which lies on the waters of the New River, principally in Fayette and Raleigh counties, West Virginia, covering a strip of territory about forty miles in length along the line of the Chesapeake and Ohio Railroad from Quinnimont to Kanawha Falls, where the New River empties into the Kanawha, the railroad following the banks of the river the whole distance. (See map.) Between Kanawha Falls and the Valley of the Ohio lies the great Kanawha region, and these two coal-fields possess a greater variety of coal than can be found in any other portion of the country, enabling them to furnish the best fuels for any of the various demands of manufacture or domestic use, the Kanawha region possessing many varieties of gas, hard splint, and cannel coal, and the New River region bituminous and semi-bitnminous, steam and coking coal. The New River, in its westward course towards the Kanawha, has cut its way entirely through the Sera1 conglomerate or No. XII of the Pennsylvania Reports, the Umbral red shales of No. XI appearing at the foot of the mountains at the eastern end of the region at Quinnimont, one of the upper ledges of the Conglomerate forming the summits; while at the western end, at Kanawha Falls, the top of the Conglomerate is nearly down to the level of the river, a portion of the " Lower Productive Measures" forming the greater portion of the mountains. These mountains rise abruptly from the banks of the river to a height of from 800 to 1200 feet, leaving only here and there narrow strips of bottom land, a few acres in extent; and as the measures consist principally of hard sandstones, shales, and conglomerates lying ill a nearly horizontal position, the mountain-sides are very precipitous, with many long and high cliffs, which, with the great height of the mountains, give the country a very rugged appearance. Along the sides of these mountains fronting on the New River and its many tributaries there are exposed the outcroppings of several veins of bituminous and. semi-bituminous coal, varying in thickness from a few inches to over four feet, five of them being workable, or

Jan 1, 1880