Search Documents

By Mark Colwell

This paper summarizes the results of a research project whose goal was to provide the Australian coal industry with a longwall installation roadway (faceroad) design methodology that could be utilized by suitably qualified colliery personnel. This goal was achieved in 2012 and the design methodology (and software package) is referred to as Analysis and Design of Faceroad Roof Support (ADFRS). The intended benefits to underground operations, in the provision of this information and resource, are a safer and more productive workplace.

By Mark Colwell, Christopher Mark

This paper summarises the results of a research project whose goal was to provide the Australian coal industry with a rib support design methodology and software tool that could be utilised by suitably qualified colliery staff. The project was primarily funded by Australian Coal Association Research Program (ACARP) and further supported by several Australian longwall operations. The outcome of the project is a design methodology and software tool called, Analysis and Design of Rib Support (ADRS). ADRS is an empirical technique, which recognises that several geotechnical and design factors affect ribline performance and in addition that operational and safety issues essentially dictate the level of performance required. Therefore, the design recommendations associated with ADRS are specific to the Australian coal industry; however the procedure(s) for data collection and analysis could be applied to other countries' 'underground coal industries. Case history data were compiled from 34 longwall and two bord and pillar operations resulting in 204 case histories with each case history data set being defined by approximately 130 individual data fields. In addition monitoring (incorporating stress cells and extensometers) was undertaken at 10 collieries to assess and quantify the effectiveness of different rib support patterns and hardware on rib performance. The monitoring sites allowed for an improved understanding of the mechanisms of rib failure and degradation in terms of its interaction with the installed support and at the various stages of the mining cycle. The design methodology deals with both mains development and gateroad development specific to Australian longwall mines. This paper focuses on longwall gateroads subjected to abutment loading and in particular the travel road which becomes the tailgate of the subsequent panel. The statistical analyses associated with these cases suggested that the level of rib support should be based primarily on the development height and the pillar stress level. The ADRS software guides users through the design process, allowing them to develop rib support plans based on sound science and a broad base of in-mine experience To the best of the authors’ knowledge ADRS is the first systematic rib support design technique to be developed for any country’s underground coal industry. The development and use of empirical models in mining have substantially contributed to improving safety and productivity. ADRS further demonstrates that empirical techniques are particularly relevant and beneficial in dealing with the complexities of geotechnical design associated with underground coal mining.

Jan 6, 2008

By R. Venugopal

Hydrocyclones have been used extensively for more than 100 years to classify mineral slurries for recirculation in grinding circuits. Sometimes hydrocyclone classification is carried out in more than one stage to improve the efficiency of classification. Factors affecting separation efficiency include fluid velocity, density, and viscosity as well as the mass, size, and density of the particles. The geometric configuration also affects its efficiency; it includes parameters like cyclone diameter, underflow and overflow diameter, position of vortex finder, height of the cyclone, feed inlet geometry, and diameter etc. Besides changes in the basic parameters some modifications in cyclone has also been introduced from time to time which have affected its efficiency, some of these are :-(i).Introduction of magnetic force along with the centrifugal and drag force to control the flow of the magnetic particles inside the chamber.(ii). Introduction of sparger, air is introduced in the chamber in the form of bubbles, to control the flow of fine particles and hydrophobic particles. (iii). Introduction of dilution technologies for the dilution of thickened underflow. (iv).Introduction of new model. In spite of wide use and simple geometry, the real working principle of hydrocyclone chamber is extremely complex because of the swirling turbulent flow inside the device. In order to get more knowledge about hydrocyclones and to increase its efficiency, past 10-15 years simulation techniques are being developed. The simulation models also enabled a deeper insight into the static and dynamic behavior of hydrocyclones. Therefore, more emphasis on simulations by methods like Computational Fluid Dynamics (CFD), Finite Element method (FEM) is given. Overall, a status review of the work carried out on the analysis of hydrocyclone performance, modeling approaches and its contribution in the efficiency of mineral processing operation is highlighted.

Sep 1, 2012

By C. Patrick

Longwall face-to-face transfers can cost over $100 per minute in lost production potential and $100,000 for personnel and supplies. Such high cost makes extensive planning and control of the transfer process a critical necessity for the economic feasibility of longwall operations. This paper reports operations research techniques used for the analysis and modeling of longwall face-to-face transfers. Transfer data has been collected from companies who operate over 30% of the total U.S. longwall faces. Comprehensive sequence networks of existing longwall transfers were developed; simulation models of transfers under varying conditions were generated; and, the economics of general transfers and time-cost tradeoffs in the transfer procedure were investigated.

Jan 1, 1993

By P. Cowx, L. Els, P. Smith, R. Nordhagen

"Tapping operations at ferroalloy smelters generate a significant amount of fume. Effective capture of fumes is required to meet the obligations of environmental, as well as occupational, legislation.A study was completed on an existing fume extraction system at a ferromanganese furnace tapping area. The area under consideration included the tap-hole, launder, and ladle area. The study consisted of site test work as well as computational fluid dynamics (CFD) modelling to identify and evaluate solutions.Site test work and observations during furnace operation provided a baseline of system performance as well as input parameters for CFD modelling. Gas flow rates and energy contents from each extraction area were measured. Photographs and video footage were taken to evaluate areas of fume leakage.The CFD study was firstly validated against site observations to ensure the accuracy of input parameters. Thereafter several modification concepts were modelled and suitable combinations were investigated to ensure robust solutions. The following concepts were considered:•,Air curtains•,Ladle hood aspect ratio and position•,Increase of ladle extraction volume•,Extension of the length of the tapping garage structureThe paper presents the results of a performance test on a working ferromanganese tapping area fume extraction system and the results of CFD modelling as compared to site test results. Upgrade options are evaluated and an integrated robust upgrade of the system described."

Jan 1, 2014

By Michael Oakland

This paper will discuss the design analysis of sheet pile cofferdams for static and dynamic blast loads. Following construction of the new Willis Avenue Bridge across the East River between Brooklyn and Manhattan, in-river piers No. 9 and No. 10 from the former bridge were demolished, partially by explosive charges. The blast at Pier 10 was conducted first and though the demolition charge was relatively small, it gave confidence that the sheeting could be designed to resist the blast load. This paper primarily summarizes our analysis and performance of a sheet pile cofferdam at Pier 9 used to withstand the larger blast loads, contain the blast debris, and allow excavation of the pier below the existing river bed mudline. The program NLFlex was used to predict stresses and deformations of the cofferdams under dynamic blast loads, using simplified equations to estimate the underwater blast pressures. Specifically, the analysis focused on the stresses in the struts, waler beam, sheet pile interlocks and connection of the sheeting to the waler beam. Design included allowing plastic deformations and limited rupture of the sheet pile interlocks under the blast loading. Comparisons are made between stresses assessed by the dynamic finite element modeling and empirical relationships used within the industry. The performance of the system after the actual blast is discussed as well as details of the performance of welded vs. bolted connections within the system.

By John Mould, Gordon Chen, Michael Oakland, William McElwee

"This paper will discuss the design analysis of sheet pile cofferdams for static and dynamic blast loads. Following construction of the new Willis Avenue Bridge across the East River between Brooklyn and Manhattan, in-river piers No. 9 and No. 10 from the former bridge were demolished, partially by explosive charges. The blast at Pier 10 was conducted first and though the demolition charge was relatively small, it gave confidence that the sheeting could be designed to resist the blast load. This paper primarily summarizes our analysis and performance of a sheet pile cofferdam at Pier 9 used to withstand the larger blast loads, contain the blast debris, and allow excavation of the pier below the existing river bed mudline. The program NLFlex was used to predict stresses and deformations of the cofferdams under dynamic blast loads, using simplified equations to estimate the underwater blast pressures. Specifically, the analysis focused on the stresses in the struts, waler beam, sheet pile interlocks and connection of the sheeting to the waler beam. Design included allowing plastic deformations and limited rupture of the sheet pile interlocks under the blast loading. Comparisons are made between stresses assessed by the dynamic finite element modeling and empirical relationships used within the industry. The performance of the system after the actual blast is discussed as well as details of the performance of welded vs. bolted connections within the system. IntroductionThe Willis Avenue Bridge is one of the major access ways from the Bronx into Manhattan. The location is shown on Figure 1. The original bridge constructed in 1901 was a swing bridge over the East River. The bridge was in disrepair and outdated with regards to its ability to handle the flow of traffic resulting in numerousaccidents.In 2007, Kiewit Constructors Inc./Weeks Marine, Inc., A Joint Venture was selected to construct a replacement bridge. The $612 million project included construction of a new bridge just to the south of the original bridge. The most notable aspect of the construction was floating and lifting the new 350 ft. long swing span in place as a single piece. However, another significant challenge was using blasting to demolish two of the abandoned piers which were within the East River. The blast would be near existing structures in both Manhattan and Brooklyn and would be within 30 ft. of the new bridge."

Jan 1, 2017

By R. A. Ford

The paper outlines: methods used for the determination of wear metals in motor and transmission oils; contaminents in motor, transmission and crusher lubricating oils; and viscosity determinations. Case histories and costs are presented to illustrate the value of an oil analysis program. Introduction NORANDA MINES LIMITED (BELL COPPER DIVISION) is located on the shores of Babine Lake, approximately 450 miles north of Vancouver, British Columbia. Access to the mine is by road from Topley, B.C., about 40 miles away. When a preventive maintenance analysis program was first considered, it was obvious that if samples were to be sent out for analysis, results would not be available for at least a week, due to the distance from any commercial laboratory. The assay laboratory was asked to investigate the possibility of determining wear metals on site. A limited program was started soon after production commenced, and this has now grown to include all large mobile equipment as well as crushers and grinding mills. The laboratory also now determines viscosity, fuel dilution, dirt and abrasives, glycol and water. All these results are ready within two days. This paper will outline the methods used, data interpretation, several case histories and the benefits from such a program.

Jan 1, 1977

By M. D. Schlesinger

Mercury exists in coal at very low levels; the structure of coal, the vapor pressure of mercury, and its almost universal occurrence introduce unusual problems into the analytical methods. Round-robin analyses by several laboratories, each using its own techniques, indicate that the average mercury content of coal is about 0.2 part per million. Some western coals are as low as 0.05 ppm.

Jan 1, 1971

By M. Firdaus, M. A. H. Shuva, M. A. Rhamdhani, G. A. Brooks, S. Masood, M. A. Reuter

Declining grade of primary ores and resource efficiency have led us to process more alternative metal resources such as e-waste. One of the processing routes for extracting valuable metals from e-waste is through the black copper smelting. However, the underlying knowledge of the thermodynamics behaviour of the valuable metals contained in e-waste during smelting are limited which prevent us from developing an optimised process to recover all the metals. These different metals clearly will have different favourable conditions for their extraction. To illustrate this, the distribution behaviour of germanium (Ge) and palladium (Pd) between liquid copper and ferrous-calcium-silicate slag during black copper smelting was analysed. It was demonstrated that oxygen partial pressure and slag composition affect the partitioning of these metals to the copper phase and the favourable slag chemistry for recovering these metals is opposing. Considering the available thermodynamic data of these metals, an analysis for the optimum conditions is presented.

Mar 1, 2017

By Leonardo Camilo dos Reis, Edmilson Fernandes Dadomi, Claudio Silva de Paulo

In the hot strip mill production, one of the factors that may affect the productivity is the occurrence of failure due to the geometry of the strip at the exit of the rolling mill, because the tip of the strip can turn-down or turn-up. This study had the objective of evaluating the behavior of the strip when leaving the working rolls, through numerical simulation, aiming to know the influences of the main variables that govern the formation of the turn-down. The methodology consisted in performing the computational simulation of the strip mill and to vary the operational and geometric parameters that could influence the process. The results showed that the rolling of hot strips of HSLA material with final thickness varying between of 3 to 6 mm and a reduction of 6.6% to 11.0% in the last stand of a hot strip mill, tends to bend towards the roll with larger diameter, higher friction coefficient , higher temperature and lower limit of material flow. It was observed that the variation in diameter is the main factor that contributes to the formation of the curvature of the front-end of strip. Based on these results, several measures were implemented in the industrial line, with a significant reduction in the occurrence of turn-down.

Oct 2, 2019

By Robert J. Timko, Edward D. Thimons, Robert L. Derick

In early June, 1986, a fire of unknown origin erupted in one of several main entries of a coal mine located in southwestern Colorado. The fire was aggressively fought with high- expansion foam. As a result of several strategic decisions, the fire appeared to be held in check. Unfortunately, sufficient quantities of foam were unavailable and as soon as the foam was depleted, control of the fire was lost. To prevent further damage and the possibility of an explosion, all entries to the mine were sealed. This paper recounts activities from the discovery of the fire to the initial reentry of the sealed mine including location of the fire, the decisions made to best combat it, and the steps taken to rapidly and securely seal the mine when this became necessary. The mine operator requested the Bureau's assistance in obtaining and analyzing mine fire gases taken from sampling ports placed through the mine seals. This report describes how samples were taken and what gases were analyzed. In addition, this work describes the initial exploration of the sealed mine by personnel using oxygen breathing apparatus.

Jan 1, 1987

By Frederick B. Kuhnow

Harmonic energetic delamination of T2 building is being considered for demolition at a formerly known atomic lab. The T2 building is within a containment structure that is under a negative pressure of -49 Pa (-0.2 inches of WC) so that no remaining radioactive material is leaked out. The T2 containment enclosure is a portal frame-type system that spans east/west over 35.05 m (114’-11 7/8”) and spaced 2.9 m (9’-6”) apart. The west side of the portal frames is supported by a 64 cm (2’-1”)thick concrete wall which is backfilled to the west and open to the T2 basement to the east. The east side of the portal frames is supported by a 61 cm (2’-0”) thick concrete wall that is backfilled to the east and open to the tank farm vaults to the west. A concrete slab-type footing supports both the east and west walls. Transverse walls provide lateral support for the walls as part of the original design. The west wall has an elevated slab that provides further stiffening of the concrete wall between the transverse walls.

Jan 1, 2017

By Ihsan Berk Tulu, Ted Klemetti, Deniz Tuncay

"The Analysis of Retreat Mining Pillar Stability (ARMPS) program was developed by the National Institute for Occupational Safety and Health (NIOSH) to help the U.S. coal mining industry to design safe retreat room and pillar panels. ARMPS calculates the magnitude of the in-situ and mining-induced loads by using geometrical computations and empirical rules. In particular, the program uses the “abutment angle” concept in calculating the magnitude of the abutment load on pillars adjacent to a gob.In this paper, stress measurements from U.S. and Australian mines with different overburden geologies with varying hard rock percentages were back analyzed. The results of the analyses indicated that for depths less than 650 ft, the ARMPS empirical derivation of a 21° abutment angle was supported by the case histories; however, at depths greater than 650 ft, the abutment angle was found to be significantly less than 21°. In this paper, a new equation employing the panel width to overburden depth ratio is constructed for the calculation of accurate abutment angles for deeper mining cases.The new abutment angle equation was tested using both ARMPS2010 and LaModel for the entire case history database of ARMPS2010. The new abutment angle equation to estimate the magnitude of the mining-induced loads used together with the LaModel program was found to give good classification accuracies compared to ARMPS2010 for deep cover cases.INTRODUCTIONIn the early 1990s, the Analysis of Longwall Pillar Stability (ALPS) was introduced by Mark (1990) as a chain pillar design software and was generally accepted and used by the U.S. coal mining industry. Following the success of ALPS, the National Institute for Occupational Safety and Health (NIOSH) developed the Analysis of Retreat Mining Pillar Stability (ARMPS) program for designing retreat mining pillars using a similar approach as ALPS (Mark and Chase, 1997). The Australian mining industry also recognized the success of ALPS, and Colwell, Frith, and Mark (1999) calibrated the program to Australian conditions. The ALPS and ARMPS programs draw their strengths from the large databases that are used to calibrate them (Mark, 2009). However, following the Crandall Canyon Mine collapse in 2007, NIOSH had to reconsider the pillar design criteria used in deep-cover retreat mining (Mark, 2010). The ARMPS overburden load prediction algorithm was improved to more accurately predict the loading of narrow panels with high overburden depths by implementing the pressure arch concept, and this new version is called ARMPS2010."

Jan 1, 2019

By Ihor Kunasz

The high lithium demand forecasted for some high tech applications and batteries for electric and hybrid-electric vehicles, in particular, has sparked increased exploration for lithium, particularly for lithium- and potassium-bearing brine deposits. The latter have generally followed the Canadian Institute of Mining, Metallurgy and Petroleum (CIM) NI 43-101 guidelines on resource reporting, formulated for hard rock deposits (metals and industrial minerals). While a number of the requirements can be appropriately applied to brines, brines are fluids and require a specific analysis leading to a distinct set of reporting requirements. Brines cannot be considered industrial minerals because the various elements occur as ions in a dynamic fluid, rather than being chemically bonded in a solid. Although chemicals are produced from brines, brines have no relation to industrial mineral deposits. This article analyzes the recently released (Nov. 1, 2012) document CIM Best Practice Guidelines for Resource and Reserve Estimation for Lithium Brines, in light of the practical knowledge available from existing brine operations. It recommends modifications to the guidelines, which, if applied in their present format, will result in overstating resources and reserves and mislead potential investors. The CIM Best Practice Guidelines for Resource and Reserve Estimation for Lithium Brines document is generally descriptive and does not fully address the methodology for brine resource or reserve definition. Lithium and other elements (potassium, magnesium) are contained in a fluid, the hydrologic characterization of which should be the principal focus of a brine exploration program. The fundamental requirement in defining lithium brine resources and reserves in a salar is the identification and definition of those formations ? the aquifers ? that will yield brine in a usable quantity to a well, because brines can only be extracted by pumping wells. Fine-grained sediments will never, as required in the summary Table 1, have ?reasonable prospects of economic extraction,? cannot be considered and, therefore, need not be tested. However, the guidelines recommend the collection of solid samples and a high-core recovery for laboratory testing of various sediments instead of focusing on the brine.

Oct 1, 2013

By Zach Agioutantis, Christopher Mark

"Thirty years ago, the Analysis of Longwall Pillar Stability (ALPS) inaugurated a new era in coal pillar design. ALPS was the first empirical pillar design technique to consider the abutment loads that arise from full extraction, and the first to be calibrated using an extensive database of mining case histories. ALPS was followed by the Analysis of Retreat Mining Stability (ARMPS) and the Analysis of Multiple Seam Stability (AMSS). These methods incorporated other innovations, including the Coal Mine Roof Rating (CMRR), the Mark-Bieniawski pillar strength formula, and the pressure arch loading model. They also built upon ever larger case history databases and employed more sophisticated statistical methods.Today, these empirical methods are used in nearly every underground coal mine in the US. However, the piecemeal manner in which these methods have evolved resulted in some weaknesses. For example, in certain situations, it may not be obvious which program is the best to use. Other times the results from the different programs are not entirely consistent with each other. The programs have also not been updated for several years, and some changes were necessary to keep pace with new developments in mining practice.The Analysis of Coal Pillar Stability (ACPS) now integrates all three of the older software packages into a single pillar design framework. ACPS also incorporates the latest research findings in the field of pillar design, including an expanded multiple seam case history data base and a new method to evaluate room and pillar panels containing multiple rows of pillars left in place during pillar recovery. ACPS also includes updated guidance and warnings for users and features upgraded help files and graphics.INTRODUCTIONPillar design is one of the fundamental elements of mining engineering. Pillars are necessary to control the great weight of the overburden during all phases of underground mining. Without stable pillars, ground control is impossible."

Jan 1, 2018

By A. K. Kyllo

A study has been carried out on the dusts from Hudson Bay Mining and Smelting's Flin Flon copper smelter. The aim of the work was to determine the mechanisms of dust formation and the deportment of the various constituents. The work concentrated on the copper converters, but the electrostatic precipitators and baghouse also clean the reverberatory furnace off gas, so some mixing will have occurred. The dust composition was found to vary with distance from the furnace, and to be made up of three major components: solidified droplets, unreacted flux, and condensed particles. The solidified droplets were formed from material ejected from the converter during blowing, while the flux was blown out of the converters immediately after charging. The condensed particles contained the majority of the lead and zinc, as well as the volatile impurities. There was also a significant soluble content of the dusts, increasing with distance from the furnace. The condensed material may be separated from the remainder by a simple washing and sizing technique.

Jan 1, 1996

By Jason Baird, Braden Lusk, Dominique Nolan, Allen Stults

Conical shaped charges have been used to penetrate rock for many years now. Examinations have been made looking at shaped charge liner geometry, material, and standoff, as well as explosive composition, confinement and initiation. Most of the testing conducted towards penetration rather than cratering has fallen within the realm of the petroleum industry and as such been confined to specific rock types, with test apparatus that include simulated down hole (subterranean) environments. The testing conducted within this experimentation is conducted at ground level, in small scale samples, using a single standoff, against multiple rock types. The data collected from that testing is examined here and relationships between physical properties of the rock and the liner are analyzed. The analysis of that data raises the possibility of a relationship that may lead to new empirical methods of penetration prediction in rock.

Jan 1, 2012

By I. Cotman

Dimensional stone processing has become an important part of the world extractive industry, and today?s total stone block yearly production is estimated to be around 134.000.000 tons and is still growing by an average yearly rate of approximately 20%. In future, the same production will become an important part of the mining industry and presently, in some countries it represents even the main mining output. New environmental regulations, together with landscape and nature conservation requirements, create a number of difficulties in setting up new open pit dimensional stone quarries. As a result, many dimensional stone producers have recently started to apply underground techniques in order to produce the ornamental stone blocks intended for further processing. Underground production of stone blocks requires special mining methods and so far it has not been a cost-effective excavation method for all types of rocks. Presently, this type of stone excavation is generally applied in sedimentary and marble deposits because the rock has small to no mineral quartz content. When starting a new underground dimensional stone mine, it is necessary to analyse the impact of all primary factors which are crucial to set up a technically and cost effective advanced underground dimensional stone mine. The role of physical and mechanical properties of the rock, geological conditions, mineralogical composition, micro-tectonic state of the site, rock mechanic conditions on the site, durability and saw ability of the stone are decisive factors in foreseeing the future methods of extraction. The laboratory research work as well as the field work, is very important in decision-making aimed to choose the future excavation method. Also of equal importance is the serious market research, because it renders the indication of selling price potential. Having obtained the results from both types of research, mining engineers can design the mining methods which optimize financial return to the mine. The practice approved by 15 years of testing in the underground limestone quarry of Kanfanar gives future producers very useful advice and general data to facilitate the process of exploration intended to establish new similar underground quarries.

Aug 1, 2013

By Shi Yuan

Molten copper was deoxidized using a one-end-closed yttria-stabilized zirconia (YSZ) tube. A thin layer of porous Ni-Zr02 cermet electrode was deposited on the inner wall of the YSZ tube. The outer surface of the tube was in contact with the melt and the inner surface with a flowing reducing gas. Without applying external EMF, the melt was deoxidized by short-circuiting the melt with the cermet electrode. The deoxidation process was analyzed and the rate controlling steps were identified. These experiments were also conducted at different temperatures to evaluate the effect of temperature on the deoxidation kinetics.

Jan 1, 1994