Search Documents

By Wenbin Liu

A novel route for rapid synthesis of ultrafine WC-Co cemented carbides with homogeneous binder phase distribution is reported. The composite powder is produced by in situ reduction-carbonization reactions by using WO2.9, Co3O4 and carbon black as raw powders. The reaction equilibrium and phase stability are studied by thermodynamic calculations. The WC-Co composite powder is condensed by spark plasma sintering (SPS) to obtain the cemented carbides bulk. The sintering temperature is lower than that in the conventional sintering methods by 1500C, while the sintering time is remarkably reduced by 3-5 times. The high performances of the hardness and the fracture toughness are obtained. The experimental results confirm that the present processing scheme of in situ reduction-carbonization reactions and subsequent SPS sintering is an efficient way to prepare WC-Co cemented carbides, and is apparently superior to the conventional long-period techniques of preparing composite powder and cemented carbides bulk.

Jan 1, 2008

By Herman D. Mendoza

A rapid recovery/recycling process was introduced utilizing the surface-chemical properties of finely dispersed mercury and alumina (Al2O3) fibers in aqueous environment. The conventional method of amalgamation or .ball milling. involves the mixing of a substantial amount of mercury to collect free gold during the grinding stage. In effect, a portion of the mercury is transformed into minute droplets that readily float and disperse in the amalgamation effluent. The fine droplets of mercury in the dispersion readily attached onto the positively charged macroscopic alumina fibers (i.e. = pH 9.8) at conditions pH 3 to 10. When an effluent from settling procedure after an amalgamation-grinding stage is passed through a column-bed packed with alumina fibers, maximum collection of negatively charged finely dispersed mercury occurred at pH 3 to 6. The collection/attachment efficiency was 99.5%. The collected droplets of mercury, which are left in the column-bed of alumina fibers, were subsequently rinsed with alkaline solution at pH 10 to 11.5. At these conditions, both mercury and alumina fibers carry negative surface potentials and resulted in the partial detachment of mercury from the alumina fibers. The detachment efficiency was only 30-35%. The attachment/detachment mechanisms in this study were analyzed using the DLVO theory.

Jan 1, 2003

By A. V. Deforest, A. R. Anderson, C. W. MacGregor

ONE of the important problems in the design of structures and machine parts subjected to rapidly applied loads is the determination of the strength and ductility of the material itself under such conditions. Realizing the need for such information, many investigations have been carried out in the past. Most of these experiments have been made using notched bars in bending either with the Charpy or Izod impact machine. While yielding valuable data on the effect of notches in the energy absorption of the material and on the condition of heat-treatment, this form of test does not lend itself readily to a determination of fundamental stress-strain relations. For this and other reasons, more attention has been paid recently to the tension impact test. An extensive literature already exists on the subject and only those investigations somewhat closely related to the present paper will be mentioned. For a more comprehensive list, the reader is referred to the Symposium on Impact Testing of the A.S.T.M., 1938. The work of Mann,1 Clark and Dätwyler,2 Nádai and Manjoine,3 Winlock and Leiter,4 Deutler,5 and Brinkmann,6 however, deserve especial mention. In most of the previous investigations on the subject, when stress-strain relations were obtained under high rates of loading, it was the common procedure to determine stresses based on the original area and strains based on the original length. Stress-strain curves were then constructed by [P OL, plotting So = Ao as a function of eo = Lo] where A o and Lo refer to the original area and gauge length, respectively. At present there exists a paucity of true stress-strain data in the impact problem. The advantages of constructing so-called true stress-strain curves in order to reveal the fundamental physical properties of the material for the tension test were discussed recently by one of the authors' It was shown that the true physical behavior of the material in the tension test could best be represented [by plotting the average true stress, S = P as a function of e = q' = log o = log Log] where P, A, L, S, e, and q' refer to the load, the cross-sectioned area while the load P is applied, the actual gauge length, the average true stress, the true strain and true reduction in area, respectively. Besides giving a better physical representation, the method has certain additional advantages in that the stress-strain curve so plotted becomes a straight line from the maximum load point to fracture. The construction of such- curves, however, while comparatively simple for the slow rates of loading customarily used in the tension test, presents certain difficulties for tensile impact in that both loads and diameters are required throughout the test. The continuous measurement of test-piece

Jan 1, 1941

By A. V. Deforest, A. R. Anderson, C. W. MacGregor

ONE of the important problems in the design of structures and machine parts subjected to rapidly applied loads is the determination of the strength and ductility of the material itself under such conditions. Realizing the need for such information, many investigations have been carried out in the past. Most of these experiments have been made using notched bars in bending either with the Charpy or Izod impact machine. While yielding valuable data on the effect of notches in the energy absorption of the material and on the condition of heat-treatment, this form of test does not lend itself readily to a determination of fundamental stress-strain relations. For this and other reasons, more attention has been paid recently to the tension impact test. An extensive literature already exists on the subject and only those investigations somewhat closely related to the present paper will be mentioned. For a more comprehensive list, the reader is referred to the Symposium on Impact Testing of the A.S.T.M., 1938. The work of Mann,1 Clark and Dätwyler,2 Nádai and Manjoine,3 Winlock and Leiter,4 Deutler,5 and Brinkmann,6 however, deserve especial mention. In most of the previous investigations on the subject, when stress-strain relations were obtained under high rates of loading, it was the common procedure to determine stresses based on the original area and strains based on the original length. Stress-strain curves were then constructed by plotting [So = ooT as a function of eo =o] where A o and Lo refer to the original area and gauge length, respectively. At present there exists a paucity of true stress-strain data in the impact problem. The advantages of constructing so-called true stress-strain curves in order to reveal the fundamental physical properties of the material for the tension test were discussed recently by one of the authors? It was shown that the true physical behavior of the material in the tension test could best be represented by plotting the average true stress, [S = P] as a function of [e = q' = log A-le = log Lo] where P, A, L, S, [e], and q' refer to the load, the cross-sectioned area while the load P is applied, the actual gauge length, the average true stress, the true strain and true reduction in area, respectively. Besides giving a better physical representation, the method has certain additional advantages in that the stress-strain curve so plotted becomes a straight line from the maximum load point to fracture. The construction of such curves, however, while comparatively simple for the slow rates of loading customarily used in the tension test, presents certain difficulties for tensile impact in that both loads and diameters are required throughout the test. The continuous measurement of test-piece

Jan 1, 1941

By G. Bonin, R. P. Preston

"This paper presents a series of case studies where spherical camera photographs were used to generate 3D shaft models using photogrammetric methods. The shaft models were, checked for accuracy by comparing them to overlapping laser scan data, provided survey data or idealized shaft models. Short lengths of model were found to more accurately reproduce the shaft surface, with a best observed accuracy of 8 mm. Longer models encountered errors with accumulated errors as exhibited by slight deviations from vertical or slightly conical model shape. At present, the models are considered acceptable for general documentation and gross change detection. INTRODUCTION Shaft inspections are required by mining regulations in many jurisdictions and are commonly completed by trained mine personnel via visual inspections. This can be time consuming and prone to errors due to lapses in attention and the rapid travel rate required to inspect an entire shaft in a reasonable amount of time. Similarly, because of the time requirements, there can be impacts on other aspects of mining as a result of occupying the shaft for inspections. Spherical cameras with supplemental light systems offer a modern addition or alternative to conventional inspections. These cameras can be lowered relatively quickly to collect high definition, fully illuminated videos of the shaft that can be reviewed in detail later while the shaft returns to service (Gillis et.al., 2019). The use of cameras offers a further opportunity for valuable survey data generation from the same original data stream. The video data can be processed into three-dimensional (3D) models using Structure-from-Motion (Westoby et al., 2012) based photogrammetric methods. Depending on the quality of the source video and availability of survey control (required for all photogrammetry models) these models can be very accurate. Shaft surveying can be conducted with traditional theodolite methods but such surveys are time consuming and limited in their data density. Similarly, scans can be completed using conventional terrestrial laser scanners, but this requires a significant number of distinct setups to provide sufficient overlap between scans. Work is being conducted both on the laser scanning (SLAM, Durrant-Whyte & Bailey, 2006) and photogrammetry fronts towards kinetic scanning (Benecke, 2017) systems. The major advancement which is permitting these kinetic systems is Inertial Measurement Units (IMUs) which can provide localization in GPS denied environments and reduce errors associated with the open traverse format associated with shaft scanning."

Jan 1, 2019

By J. Botha

There are many underground mining software tools available to plan and schedule the development of underground mines. A shortfall of these tools is the optimization of the underground equipment and strategy in order to maximize the development rate. This paper will illustrate how the SimMine® software was used to maximize underground development at Petra Diamonds' Cullinan Diamond Mine. It will also determine the effect of various development strategies and equipment capacities on the underground development rate and pinpoint potential bottlenecks in the mine development cycle.

Jan 1, 2010

By Eugene P. Pfleider

The mining industry of the World, and particularly of the United States, has made a complete reversal from underground to surface mining methods since the turn of the 20th Century. This has occurred even as average ore grades were decreasing and strip ratios rising. In the early 1900's there were over 100 underground mines producing from the three iron ranges of Minnesota -- today there are hone. Practically all of our coal prior to 1930 was mined underground; today over one-third is from surface operations and that percentage is increasing. Although world mining has hot changed to surface techniques as rapidly as has the U. S. Industry, the shift is escalating and will approach our figures shortly. A comparison of World and U. S. production figures are shown in Table 1, taken from the AIME Surface Mining volume, and the trend rates for the U. S. are depicted in Fig. 1.

Jan 1, 1968

By Zay Jeffries

Rearmament superimposed on buying sprees by the public, caused a general shortage of metals in 1911. and the rare metals were no exception; they also shared with the more common metals the uncertainty of future demand. In general, the apparent undersupply of metals is a favorable condition for the realization of sleeping possibilities of the rare metals, especially if the supply can he made sufficient to take care of the possible new demand. Many changes in metal usage in 1941 were forced because of shortages. When such changes are in the direction of the economic trend there is a speeding up in the tempo of the inevitable change, but when the forced changes are against the economic trend they are likely to be shortlived. In any event, the latter is not a solid foundation on which to build a future business.

Jan 1, 1942

By L. Y. Zhang

The current status of metal hydride alloys for NiMH batteries was systematically reviewed. Extensive application-oriented research and development has successfully made the NiMH battery an important part, with growing potential, among rechargeable batteries. The rare earth based metal hydrides (AB5) have been considered the best alloy material for use in the negative electrode in NiMH batteries. However, being in demand for high performance electronic markets, the still young NiMH industry is facing serious technical challenges in developing better products. Among all the efforts to respond to the challenges, advanced AF3, alloys are in great demand: the capacity enhancement race requires new or improved alloys possessing higher volumetric capacity; price competition mandates MH materials with low cost; high performance under severe service environments calls for alloys with high corrosion resistance when subjected to electrochemical cycling; and finally, high power service requires the negative electrode to deliver current at high rates.

Jan 1, 1997

By John R. Goode

"The year 2011 witnessed a major surge in rare earth prices as China, supplier of +95% of the world’s rare earths, reduced export quotas and increased export taxes and duties. In response, companies around the world are scrambling for alternative sources. In Canada too, there is a race to be the “first” rare earth producer. Something that is not generally realized is that Canada has a long history of rare earth production and was a major supplier from the early 1960’s to 1990. At one stage, Canada was said to be supplying more than one third of the world’s yttrium and probably supplied even more than that. Five decades ago, thorium was a key element in many non-nuclear applications and Canada became a major supplier of thorium from the late 1950’s to 1968, first as a by-product of uranium and then as a co-product of rare earths. This paper reviews the development of Canada’s original rare earth and thorium production facilities, which were located in the Elliot Lake uranium camp in Northern Ontario. The uses of these elements, geology, mineralogy, markets of the time, and processing are all discussed. Some of the lessons learned from these pioneering operations might be useful in today’s race to develop the next generation of rare earth production plants.INTRODUCTION The rare earths and thorium were first identified in the early 19th century but were little more than curiosities for the next century. However, in the mid-1960’s the invention of rare earth-based phosphors for the cathode ray tube in colour television sets launched a major demand for certain rare earths. The use of thorium as an alloying agent in aircraft and missiles grew rapidly in the late 1950’s. In the same period, demand for uranium for both weapons and power production soared. Also in the late 1950’s, the Elliot Lake uranium-thorium-rare earth deposits (also known as the Blind River deposits) were discovered. This conjugation of events led to uranium production in the Elliot Lake camp, quickly followed by the co-production of thorium and, later, the rare earths. Uranium production in the Elliot Lake camp continued from 1955 to 1996. Thorium was produced continuously from 1959 to 1969. Rare earths were produced, intermittently, from 1965 to 1990. Complete production records are not readily available for thorium and the rare earths but unquestionably Elliot Lake production made a significant contribution to world production. This paper is intended to present as much of the information that is available."

Jan 1, 2012

By A. Bhagavatula, M. Rezaee, M. J. Kiser, R. Q. Honaker

"A field study of the coal preparation plant fleet in the eastern United States was undertaken to determine if quantify of rare earth elements (REEs) present in the product streams are large enough to justify further concentration. Representative composite samples were taken from the clean product, coarse refuse, and fine refuse streams from 20 coal preparation plants. Each stream was then separated into various size and density classes and analyzed for ash and REE contents. The large database showed that coarse refuse contained the largest amount of REEs, although the ratio of heavy to light REEs was greater for the clean coal products. The concentration of REEs was also compared to that typically seen in the earth’s crust. This enrichment ratio ranged from approximately 1.5 to more than 4.0 as the ash content varied. The database also showed that a linear correlation existed between La and Ce for many REEs of interest, although there were several notable exceptions for some of the high-value REEs. INTRODUCTION Worldwide energy demand is expected to grow by as much as 37% by 2040 according to the International Energy Agency (2014). This growth, coupled with a decrease of the reliance on coal to generate energy, means that it is more important than ever for countries to secure the materials necessary to meet its energy projections. For the United States, the U.S. Energy Information Administration (EIA) predicts that total domestic electricity use will increase roughly 25%, from 3,836x109 kWh in 2013 to 4,797x109 kWh in 2040 (EIA, 2015). In the EIA’s reference case, coal’s contribution to electricity generation drops from 39% in 2013 to 34% in 2040. On the other hand, renewables share of electricity generation grows from 13% to 18% for the reference case. Compared to its current state, renewable energy electricity production is predicted to grow as little as 50% to as much as 121% over this time period, depending on the economic case being examined. This growth will largely be seen in the wind and solar sectors (EIA, 2015). The focus on viable renewable energy resources will be crucial to the future of fueling American growth. Many of the renewable energy technologies, such as wind turbines and photovoltaic films, rely on materials and supply chains outside of the United States. The lack of a reliable and low-cost domestic supply could pose a threat to the growth of the renewable energy markets in the United States. This potential vulnerability recently led the United States Department of Energy (DOE) to create a Critical Materials Strategy Report. In this report, 15 elements were identified as critical for the continued growth of the renewable energy market. Eight of these elements were rare earth elements (REEs). Five REEs (dysprosium, neodymium, terbium, yttrium and europium) were identified as highly critical and vulnerable to shortages (Bauer et al., 2012)."

Jan 1, 2016

By S. Hlajoane, L. S. Mokhahlane

The demand for rare earth elements has increased around the world due to their application in a variety of technological advancements. Previous studies have evaluated the potential of the rare earth elements and yttrium (REY) hosted within the Permian coal deposits of the main Karoo Basin (MKB) in Southern Africa. However, not a lot of scientific research has gone into the Triassic coal deposits. The Triassic coals in South Africa were the first coals to be exploited for their thermal use in the 1880s, but the discovery of the higher rank and more abundant Ecca coal deposits led to the Triassic coals remaining largely unexplored. The demand for rare earth elements has sparked interest in these coal deposits as potential sources for valuable minerals. Late Triassic coal deposits in Lesotho have previously not been well documented and these low-rank coals can be a potential source of rare earth elements. This study aims to characterize and evaluate the potential of REY in the Taung coal deposit, southwest of Lesotho. Coal and associated argillaceous samples from the Taung coal deposit were analyzed using microscopic petrography for coal characterization and an inductively coupled plasma mass spectrometry (ICP-MS) to determine the amount of rare earth elements. Taung coal is classified as middle medium rank D bituminous coal. The total REY content in Taung coal and its associated rocks range from 162.9 ppm to 855.1 ppm, which is significantly higher than the upper continental crustal (UCC) average. The average critical REY concentration of samples from the Taung coal deposit is 189.4 ppm, which is three times higher than that of the Chinese Bayan Obo deposit. Samples classified as very promising and promising because of their outlook coefficients, are found to contain up to 77% of critical REY. It is envisioned that the area could be a prime deposit for these REY.

Nov 6, 2024

By F. Dutoy, M. B. Stella, C. F. Carrozza

Rare earth elements (REEs) are indispensable components in the manufacturing of high-tech devices, renewable energy technologies, and defence applications. As global demand for these elements continues to rise, there is a pressing need to optimize extraction processes for both efficiency and environmental sustainability. This study explores approaches to rare earth extraction using Ionquest® 801 and integrates a predictive modelling to enhance process understanding and optimization. We conducted a screening test varying pH process to evaluate the best extraction efficiency. Starting pregnant leach solution (PLS), solution was prepared in the lab with the following rare earth elements: La, Ce, Gd, Dy, and Υ, at 0.02 M for each element. The data obtained were used to develop empirical and mechanistic models to predict rare earth extraction yields and flowsheet. Further tests were performed by mixing specific concentrations of different extractant and/or phase modifier. Our experimental results demonstrated the effectiveness of the proposedextraction methods, highlighting improvements in both yield and selectivity. The developedmodels successfully captured the complex relationships between process parameters and extraction efficiency, providing valuable insights for process optimization.

Nov 6, 2024

By Y. Mudryk, D. Paudyal, K. A. Gschneidner, V. K. Pecharsky, M. Khan

"Rare earth intermetallic compounds are utilized commercially as magnetic and battery materials, electron gun electrodes, etc. Several of these intermetallics will be briefly discussed. There are many other rare earth intermetallic compounds which are not utilized industrially but have unusual properties which are of fundamental interest and may have future technological applications. Several of these materials are discussed as well.INTRODUCTIONTens of thousands of rare earth intermetallic compounds exist, but physical properties (primarily their magnetic behaviors), other than their crystal structures have been measured for only a small percentage of these materials. Among these are the commercially important compounds: Nd2Fe14B, and the SmCo5 – Sm2Co17 family – well known high strength permanent magnets; (Tb0.3Dy0.7)Fe2, Terfenol-D, a giant magnetostrictive material; LaNi5Hx a critical component of the rechargeable Ni metal hydride batteries; and LaB6 an electron emitter. There are, however, many other intermetallic compounds which are not utilized industrially, but none-the-less, exhibit interesting, and sometimes, exotic physical properties which are of fundamental interest and may have some future technological significance. These include: the giant magnetocaloric effect compounds Gd5Si2Ge2 and La(Fe13-xSix)Hy; the RCu and RAg families of ductile intermetallics; the mixed intra-lanthanide (R,R')Al2 compounds in which magnetic transitions disappear and reappear as one R is substituted for by R'; and GdNi which exhibits large dilations along two crystallographic directions and a larger contraction in the third direction at the Curie temperature resulting in zero volume change as GdNi orders magnetically via a second order phase transition.COMMERCIALLY IMPORTANT INTERMETALLICSNdFeB Permanent MagnetsThe Nd2Fe14B permanent magnets were discovered in 1984 independently in the USA and Japan. It is a ferromagnet and with proper heat treatment and processing Nd2Fe14B is the strongest near room temperature permanent magnetic material known today. This intermetallic compound is utilized as a permanent magnet in many applications, such as electric motors (e.g. the modern automobile contains up to 35 electric motors), spindles for computer hard disc drives, microphones and speaker magnets for cell phones and other audio equipment, direct drive wind turbines, actuators, and Magnetic Resonance Imaging (MRI) units. There are two kinds of NdFeB permanent magnets – bonded and sintered. The bonded magnets have a lower magnetic strength than the sintered magnet. The highest strength magnets are obtained by small substitutions of Dy (up to a maximum of 10%) for Nd, because Dy can significantly increase the coercivity and thus the energy product (a measure of the magnetic strength or hardness). The bonded magnets account for about 12% of the NdFeB market (~82 metric kt per year, containing ~20 kt/a of Nd). The NdFeB permanent magnet market is growing at a rate of about 15% per year. (Burzo & Kirchmayr, 1989; Kobayashi & Hirosawa, 2001; Coey, 2011)."

Jan 1, 2012

By Stephen B. Castor

The rare earth elements (REE) which include the 15 lanthanide elements (Z = 57 through 71) and yttrium (Z = 39) are so called because the elements were originally isolated in the late 18th and early 19th centuries as oxides from rare minerals. Most REE are not as uncommon in nature as the name implies. Cerium, the most abundant REE (Table 1), comprises more of the earth's crust than copper or lead. Many REE are more common than tin and molyb¬denum, and all but promethium are more common than silver or mercury (Taylor, 1964). Promethium (Z = 61) is best known as an artificial element, but has been reported in very minute quantities in natural materials. Lanthanide elements with low atomic numbers are generally more abundant in the earth's crust than those with high atomic numbers. In addition, lanthanide elements with even atomic numbers are two to seven times more abundant than adjacent lan¬thanides (Table 1) with odd atomic numbers. The lanthanide elements traditionally have been divided into two groups: the light rare earths (LREE), lanthanum through eu¬ropium (Z = 57 through 63); and the heavy rare earths (HREE), gadolinium through lutetium (Z = 64 through 71). Although yttrium is the lightest REE, it is usually grouped with the HREE to which it is chemically and physically similar. The REE are lithophile elements (elements enriched in the earth's crust) that invariably occur together naturally because all are trivalent (except for Ce+4 and Eu+2 in some environments) and have similar ionic radii. Increase in atomic number in the lanthanide group is accompanied by addition of electrons to an inner level rather than the outer shell. Consequently, there is no change in valence with change in atomic number, and the lanthanide elements all fall into the same cell of the periodic table. The chemical and physical differences that do exist within the REE group are caused by small differences in ionic radius, and generally result in segre¬gation of REE into deposits enriched in either light lanthanides or heavy lanthanides plus yttrium. The relative abundance of individual lanthanide elements has been found useful in the modelling of rock-forming processes. Comparisons are generally made using a logarithmic plot of lanthanide abundances normalized to abundances in chondritic (stony) meteorites. The use of this method eliminates the abundance vari¬ation between lanthanides of odd and even atomic number, and allows determination of the extent of fractionation between the lanthanides because such fractionation is not considered to have taken place during chondrite formation. The method is also useful because chondrites are thought to be compositionally similar to the original earth's mantle. Europium anomalies (positive or negative departures of europium from chondrite-normalized plots) have been found to be particularly effective for petrogenetic modelling. REE were originally produced in minor amounts from small deposits in granite pegmatite, the geologic environment in which they were discovered. During the second half of the 19th century and the first half of the 20th century, REE came mainly from placer deposits. With the exception of the most abundant lanthanide el¬ements (cerium, lanthanum, and neodymium), individual REE were not commercially available until the 1940s. Since 1965, most of the world's REE have come from two hard rock deposits: Mountain Pass, United States, and Bayan Obo, China. GEOGRAPHIC DISTRIBUTION OF REE DEPOSITS More than 70% of the world's REE raw materials come from three countries: China, the United States, and Australia. China emerged as a major producer of REE raw materials during the 1980s, while Australian and United States market share decreased dramatically (Fig. 1). Table 2 gives recent annual production figures along with estimated reserves by country, and Fig. 2 shows loca¬tions of significant REE mining. MINERALS THAT CONTAIN REE Although REE comprise significant amounts of many minerals, almost all production has come from less than ten minerals. Table 3 lists minerals that have yielded REE commercially or have po¬tential for production in the future. Extraction from a potentially economic REE resource is strongly dependant on its REE miner¬alogy. Minerals that are easily broken down, such as bastnasite, are more desirable than those that are difficult to dissociate, such as allanite. In general, producing deposits contain REE-bearing min¬erals that are relatively easy to concentrate because of coarse grain size or other attributes. For more thorough discussions of REE¬bearing minerals see Mariano (1989a) and Cesbron (1989).

Jan 1, 1994

By D. A. Norrgran

The recent development of rare earth permanent magnets has revolutionized the field of magnetic separation. The advent of rare earth permanent magnets in the 1980's provided a magnetic energy product an order of magnitude greater than that of conventional ferrite magnets. This has allowed the design of high-intensity magnetic circuits operating energy free and surpassing the strength and effectiveness of electromagnets. New applications and design concepts focused on the mineral and metal processing industries have evolved. This technology also led to the development of various magnetic separators specifically designed for mineral processing applications. Applications which were not previously considered are now being applied to primary mineral upgrading and recycling and secondary recovery.

Jan 1, 1993

By I. Filippova, L. Filippov

"The by-product potential of light rare-earth elements (LREE, La, Ce, Nd) and rare-metals (W, Nb, Sn) within the St Austell kaolin deposits (UK) is related to the kaolinisation process, which liberates the accessory heavy minerals of the host granite in the clay matrix and allows their separation in the waste streams. As a consequence these minerals are pre-concentrated in the micaceous residue which displays relatively high LREE content (around 170 ppm) hosted by monazite which is mainly distributed (up to 95%) in the -100 µm fraction. A combined gravity/flotation concentration flowsheet, starting with classification of the residue into 3 size fractions (+150 µm, 150-53 µm and -53µm) was developed. This study presents the results of the clay-rich -53 µm size fraction beneficiation by flotation using sodium oleate and hydroxamate as collectors.The effect of dispersant addition during de-sliming operations on flotation efficiency was also investigated. The LREE grade in the floated product obtained with sodium oleate increased from 3370 ppm to 5350 ppm and recovery from 30% to 80% with dispersant which is attributed to clay coating. Comparison of flotation performance and Falcon Ultra-Fine (UF) concentration of monazite to previous results obtained with Falcon Semi-Batch (SB) gravity concentrator on the unscreened raw residue clearly shows that flotation of the fine residue is more efficient than Falcon UF and Falcon SB. Indeed Falcon UF produced high recoveries (87-95%) but with almost no enrichment (1.3-1.4 ratios) whereas Falcon SB concentration of unscreened residue produced higher grades (up to 0.6 % LREE) but with low recoveries (17-22 %). These preliminary results show that LREE can be pre-concentrated suggesting that the micaceous residue stream (and the associated tailings dams) could be considered as a potential resource for these metals."

Jan 1, 2016

By James D. Navratil

Advances in hydrometallurgy require the introduction of new separation and purification processes, but they can be complex, costly and energy intensive. Chromatographic processes have low energy requirements and possess very high separation efficiencies. However, they have not yet made the great industrial impact that might be expected from their benefits. The large-scale and difficult separation of rare earths would greatly benefit from an improved continuous chromatographic operational device. Truly continuous, multicomponent chromatographic separations may be achieved by means of the continuous annular chromatograph. Work has been Initiated at The University of New South Wales involving the improvement and development of such equipment for the separation and purification of rare earths.

Jan 1, 1990

By A. Quilodran, B. Jakovljevic, T. McCallum, P. Wong

"Rare earth separation by solvent extraction (SX) requires multiple separation plants each consisting of many extract, scrub, and strip stages to separate the individual metals. SX modeling advances have brought benefits to circuit design and process optimization by quickly narrowing test conditions without the need for exhaustive laboratory studies. Modeling can be used to optimize circuit configuration, O/A ratios, and acidities, which allows for CAPEX and OPEX savings. A comparison between pilot plant data and the results expected from modeling is presented for rare earth separations with CYANEX® 572.INTRODUCTIONRare earth separations can be difficult due to limited separation between the elements (Xie, Zhang, Dreisinger, & Doyle, 2014). This requires relatively complex solvent extraction circuits utilizing multiple extract, scrub, and strip stages as well as multiple SX configurations to achieve the desired metal purities. Designing rare earth circuits can be complex, and significant time and testing may be necessary to determine the required staging and optimal conditions.Circuit modeling for rare earth separations has been introduced to the industry using CYANEX® 572 extractant (Soderstrom, McCallum, Jakovljevic, & Quilodran, 2014). CYANEX® 572 is an acidic organophosphorus extractant formulation which has a weaker ligand-metal complex strength than that of the traditionally used phosphonic acid extractants. This allows efficient extraction while requiring a significantly lower acid concentration for stripping (Wang, Li, Zhao, Dong, & Sun, 2015). The reduced acid requirement in strip is expected to provide OPEX savings.The modeling can be utilized to quickly determine the required acidity and organic/aqueous (O/A) ratio for a given separation. It is also expected to reduce CAPEX requirements as optimal staging can be determined, and implemented.CYANEX® 572, combined with modeling, was utilized to produce a purified dysprosium (Dy) stream. To achieve this separation, multiple SX circuits were designed and operational conditions specified to separate Dy from the mixed rare earth chloride feed."

Jan 1, 2016

By AIME AIME

TWO papers, "Calcium, Strontium, and Barium Metals," by Charles Hardy and Paul M. Tyler, and "The Mining of Gems and Ornamental Stones by American Indians," by Sydney H. Ball, were presented before the Rare Minerals and Metals group at its session Tuesday afternoon in the Auditorium. Donald M. Liddell, chairman, presided. Mr. Tyler summarized the first paper, outlining the uses, history, occurrence, manufacture, production and trade, markets and prices of the three metals. In discussion, in response to the chairman's query on "what are they doing in Russia with calcium, strontium, and barium," Guy C. Riddell replied that nothing is being done on a production basis. The great rare metals plant in Moscow is active, however, on other elements. "They are making radium chloride, uranium oxide, vanadium, cadmium, tungsten, molybdenum, selenium, antimony compounds; and mercury, nickel and arsenic are under production at interior plants. The rare metals plant is busily conducting research on beryllium, rhenium, lithium, bismuth, strontium and zirconium. These are the main rare metal activities. Much hard-alloy work. for cutting and facing, is under way:

Jan 1, 1933