Search Documents

In 2005, CANMET-MMSL used its pool of expertise in ground control, open pit and underground mine engineering, mineral processing, information technology and applied mineralogy to launch a mine-to-mill research project. The objective of the project was to optimize the distribution of rock breakage energy among blasting, crushing and grinding activities, thereby maximizing the efficiency of energy utilization within comminution processes. Tests were designed to demonstrate that this approach could reduce energy consumption, thus contributing to the reduction of green house gas (GHG) production in the Canadian mining industry. The project was accomplished in collaboration with DynoConsult and Dyno Nobel Canada Inc., a world leader in commercial explosives. Data analysis from 12 blasts (six with electronic and six with pyrotechnic detonators) in three different geological formations of a quarry (soft, medium and hard rock) shows that electronic blasting technology increases rock fragmentation by 15% (in hard rock) to 20% (in soft rock). A more uniform rock fragment size distribution is also obtained. The impact of the improved quality blast product on downstream processes of the quarry is a productivity increase of 5% in rock excavation and transportation, an energy reduction of 10% at the primary crusher and an increase of 15% of the primary crusher throughput. Extended to the Canadian mining industry, such results would represent a GHG emission reduction of about 0.05 Mt/y. A soft-sensor prototype, based on primary crusher data (i.e., energy consumption, throughput, feed and product size distribution) and a simplified computerized process model, was developed for on-line measurement of the rock operating work index. Additionally, 385 rock samples and specimens were collected and prepared to determine the tensile and compressive strength of the rock material, to evaluate the aggregate crushing work index and to examine the development of micro- and macro-fractures by means of binocular and SEM microscopy. Blast-induced rock damage was evaluated at the end of the laboratory-testing program. Even though a reduction of rock hardness of around 30% was observed after blasting, the impact of the blasting method (i.e., use of electronic or pyrotechnic detonators) on the induced rock damage could not be observed. It is either absent or not perceptible with the accuracy of the measuring techniques and the number of samples analyzed.

Jan 1, 2008

By M Bilodeau, G Caro, R Beaudoin, D Labrie

In 2005, Dyno Nobel Canada Inc, DynoConsult and CANMET-MMSL used their pool of expertise in blasting, ground control, open pit and underground mining, mineral processing, information technology and applied mineralogy to launch a research project aimed at evaluating the role of electronic detonators in the development of a sustainable energy-efficient rock reduction process. The overall objectives were to improve health and safety in a mining environment and reduce energy consumption and greenhouse gas (GHG) production in the Canadian mining industry. The study was conducted in a quarry located in Nova Scotia, Canada, with the objective of taking advantage of the higher accuracy and flexibility of electronic detonators towards improving blast efficiency and measuring its impact on productivity in a quarry environment and energy savings. Optimising the blast sequence was the first aspect to be considered before starting to look at designing bigger blasts and achieving productivity improvements, without creating additional environmental concerns, as the quarryÆs location was representing a challenge in itself in the surrounding community. The use of high-speed cameras (500 fps) was an improved means of analysing blast dynamics during the firing sequence. Seismic monitoring and linear superposition techniques were also applied to validate the sequences to be tested in all three specific geological areas. The combination of field measurements allowed to identify the optimal blasting sequences that would then be delivered accurately with the electronic initiation systems. The data from 12 blasts (six with electronic detonators and six with pyrotechnic detonators) carried out in three different geological formations (soft, medium and hard rock) showed that the electronic blasting technology could increase rock fragmentation by 15 to 20 per cent. A more uniform distribution of rock fragment size was also obtained. Blast improvements on downstream processes resulted in a five per cent productivity increase in rock excavation and transportation, a ten per cent energy reduction in primary crushing and a 15 per cent increase in the primary crusher throughput. A prototype soft-sensor based on primary crusher data (eg energy consumption, throughput, feed and product size distribution) and a simplified computer process model were developed for online measurement of a rock operating work index. Furthermore, rock samples were collected and specimens were prepared in order to determine the tensile and compressive strength of the rock materials, evaluate the aggregate crushing work index and examine the development of micro and macro-fractures under binocular and scanning electron microscopy (SEM). Blast-induced rock damage was evaluated at the end of the laboratory testing program. A reduction in rock hardness by about 30 per cent was observed after blasting. However, the impact of the blasting method (eg using electronic versus pyrotechnic detonators) on the induced rock damage was either absent or not perceptible within the measurement technique accuracy and the number of samples analysed.

Jan 1, 2007

By Dalzell R. W

A Conveyor Belt Fire Test Program was initiated in 1985 by the Approval and Certification Center (A&CC), Mine Safety and Health Administration (MSHA), U.S. Department of Labor. The purpose was to evaluate the effect of entry air velocities on the burning properties of mine conveyor belts and assess fire test data from large- and small-scale tests. Belts meeting the fire-resistant standards of MSHA and agencies of other countries were tested in small- and large- scale fire tests.

Jan 1, 1988

By Raymond J. P. Brouzes

INTRODUCTION [A Decade After the 1972 Stockholm Conference] The UN-sponsored Stockholm Environmental Conference held just over 10 years ago was the first successful attempt to achieve global recognition of environmental issues. Indicative of the lack of concrete involvement in environmental protection to that time was the fact that only 15 nations had a department or ministry responsible for environmental affairs compared to today's 143. Many governments were uncertain of what were the most serious or pressing problems in their country. There was obviously a need to both identify those issues and to determine how to manage them once identified. At the same time, the public at large was becoming more critically aware that environmental protection had been neglected by government and often ignored by industry. It soon became evident that large amounts of money would have to be spent to redress some of the more evident problems. However, many developing nations were reluctant to slow down the much-needed industrial growth by imposing costly environmental controls on industry. In fact, some waived environmental control altogether as an incentive to attract industry. In some sectors, it was often stated that industrial development and environmental protection were mutually exclusive activities. The need of an awareness, commitment and dedication by all sectors of society to protect their environment was just beginning to develop, replacing the rather simplistic view that all environmental problems were caused by greedy industry.

Jan 1, 1984

By Richard A. Hunnisett

Silica sand is one of the world's most plentiful resources and is a basic necessity in our way of life. The end uses of silica sand are an integral part of our homes, transportation, and places of work. The environmental legislation enacted in the early 1970's, coupled with the oil embargo and higher than normal inflation, have had a very real impact on the industry and its primary consumers, the foundries and glass producers. The present environmental laws directed at air and water pollution and the working environment can, in most cases, be met, but not without large capital expenditures for equipment. These expenditures must reduce the funds available for expansion and modernization of existing processes which are necessary if the costs to produce industrial sand are to remain at acceptable levels. The concern for the future is the enactment of more stringent laws, and the available technology and equipment to economically comply with them.

Jan 1, 1978

By N. L. Piret, R. J. Wesely, A. E. Melin, A. D. Zunkel

At the end of the sixties new iron precipitation techniques as jarosite, goethite or hematite brought about the new generation of electrolytic zinc plants, thereby terminating the multitude of existing neutral leach residue treatment schemes. Since the eighties, increasing environmental impact considerations urge the conversion of these contaminated waste generating precipitation processes to techniques which either produce environmentally acceptable residues or minimize their formation thereby generating iron-bearing byproducts. Technologies identified and economically assessed include the hematite process either suitably improved or with subsequent upgrading, the iron extraction process and the direct smelting of neutral leach residue to slag and fumed zinc oxide.

Jan 1, 1993

Major underground gold mine developments are not common in Australia especially when they are totally owned and hence financed by a relatively small public company. Ballarat Goldfields Limited with its Ballarat East Project is such a company. Financing a $20m underground exploratory access programme in a poor economic climate places added importance on the quality of the project. Critical factors such as ore reserves, environment, planning and the development program are of immense importance in devising and implementing a workable finance package that satisfies both the shareholder and the project's needs.

Jan 1, 1990

By R. B. Coleman, T. P. McNulty

HISTORICAL PERSPECTIVE Environmental protection is not a newcomer to the minerals industry, there having been numerous examples dating from decades ago. Sometimes the awareness of a need for preservation or restoration derived from the ethics and principles of the engineers and management responsible for development and operation of a property. On the other hand, pressures to clean up industrial messes frequently were applied by special interests such as farming and ranching, recreational and conservational groups, and local governing bodies. Mineral industry environmental controls in this century have therefore been a patchwork of good intentions and bad, clean operations and dirty ones. The Hoboken siphon converter for converting copper matte while effectively capturing sulfur dioxide at a relatively high concentration was developed in Olen, Belgium in 1928, a full sixty years ago. The alternative was closure of the Hoboken smelter by Belgian government health officials who had become intolerant of sulfur dioxide emissions which were causing serious respiratory ailments in the river valley in which Olen is situated. As early as 1958, the Anaconda Company had a full-time botanist on its metallurgical research staff with the responsibility of learning how to vegetate the extensive tailings deposits at Anaconda, Montana. By that time, considerable progress had already been made in restoration of Silver Bow Creek, which at one time was “dead” for as far as 40 miles down- stream from the point of entry of acid mine drainage in Butte.

Jan 1, 1989

By R. D. Short

Environmental regulations for noise and air pollution are directly affecting the type of equipment and construction techniques being utilized for pile driving construction using diesel hammers in California and elsewhere. Consequently, the cost of construction is increasing and in some cases, the use of diesel pile hammers has been prohibited. Based on the trend in California and elsewhere in the world, environmental constraints are spreading and becoming more restrictive. The City of Tokyo, Japan, for example has banned the use of diesel hammers. Environmental restrictions on diesel hammers can be satisfied by using modern hammers, clean burning fuels, synthetic lubricants and pre-excavation techniques.

Jan 1, 1989

By T. Leftwich, G. Faison, K. Pavlich, R. Borden, S. Pavlou

Recent regulatory and policy initiatives under the Resource Conservation and Recovery Act (RCRA), and the Comprehensive Environmental Response Compensation and Liability Act (CERCLA), will have a significant effect in risk reduction requirements for the mining and minerals processing industry. For example, Congress is considering regulating 20 special wastes from the processing of ore and minerals through RCRA Subtitle D and TSCA. The performance of risk analyses and environmental planning at mining projects is often driven by Federal and state regulatory standards. Recent regulatory and policy initiatives by the Environmental Protection Agency under the Resource Conservation and Recovery Act (RCRA), and the Comprehensive Environmental Response Compensation and Liability Act (CERCLA), will have a significant effect on environmental planning and risk reduction programs for mining and minerals processing. Regulatory programs implemented under other Federal laws including the Safe Drinking Water Act, Clean Water Act, and Clean Air Act will also impact industry practices. This paper provides: 1) a brief overview of mining waste and mining waste management, and 2) a description of these regulatory initiatives and a discussion on the impacts of new requirements on environmental and risk reduction programs in the mining industry.

Jan 1, 1992

By W. F. Riggs

INTRODUCTION Flotation equipment is becoming more definitive in design as well as greater in dimension. The last ten years have witnessed the implementation of large flotation cells ranging in size from 28 to 85 cubic meters. However, small plants still operate with cells as small as 3 cubic meters. These changes have increased the operational sensitivity of the flotation system to the chemical reagents used. No scientific study has been undertaken to develop the relationship between the size of equipment and the response of reagents in the flotation system. Hence, this article is an attempt to present several observations from past experience for the purpose of stimulating future research in an area previously ignored and perhaps subsequently not used to advantage. CONVENTIONAL FLOTATION Recent advances in conventional flotation cell design have been made in two areas: a. Flotation cells are becoming larger, and b. Basic design of flotation cells has changed. They can be classified into two types: deep cell and shallow draft cell. Size and design changes of flotation cells have a greater effect on frother performance than on the performance of other chemical reagents. Hence, the discussion in the following sections is restricted to the impact of frothers in the flotation system. Flotation Cell Size The advent of increasing flotation cell size has resulted in the increase of frother consumption. There appears to be a correlation between reduced horsepower (kilowatt) consumption and increased frother consumption per ton of ore processed in the circuit. This is more prevalent when the frother chemistry remains unchanged. Another reason for increased frother consumption is the increased distance between the rotating central shaft and the lip of the cell for larger flotation machines. Increasing this distance results in increased surface area corresponding to the larger cell size. Reduced power input per ton combined with the need for longer, stronger load support of the froth bubble as a result of increasing cell size has resulted in the development of a new series of stronger and more persistent frothers. By the same token, these newer, stronger frothers are difficult to control when applied to the smaller cells. This is true even at lower dosages because the break point between too much frother and not enough frother for optimum metallurgy is normally very narrow. This problem is often exaggerated when operators have established an optimum setting for pulp level and air for the particular frother in use. Generally, the tendency is to operate the flotation cells simply by adjusting frother dosage. The increase in frother strength to accommodate the large cells often results in the realization, after a retrofit, that the existing pump box or sump which is still handling the same volume of concentrate is no longer adequate in size. Flotation Cell Design The two most common flotation cell designs installed during the past ten years are the deep cell and the shallow draft cell. The deep cell provides for complete mixing of air and pulp at the bottom of the cell. The shallow draft cell does all the mixing/pumping in the bottom haft of the cell whereas the mixing of the air is performed further up the shaft and is brought into contact with the pulp midway up the vortex. There are many preferences for one or the other. It is the author's contention that both designs have very valid concepts and must simply be suited to the particular situation as required by the operator. The following comments are subjective observations which should be explored in greater detail. The deep cell mixes both air and pulp together at the bottom of the cell requiring a full depth ascending of the homogenized air to the surface to form the froth layer. This design, in combination with charged air, provides for good concentrate grade control under adverse conditions of selectivity, especially when faced with a fine grind and a slime-laden gangue. A selective frother can be applied without a competitive loss in recovery. One of the conditions for good selectivity in this environment is operating at medium pulp solids concentration in the range of twenty-six to thirty-four per cent (26-34%). When a higher solids concentration is used in combination with a coarse grind, it becomes difficult to maintain the same recovery with a selective frother due to higher pulp viscosity. This condition sometimes results in an unacceptable coalescence of the air bubbles as they ascend the full height of the deep cell. The increased pulp viscosity at higher solids concentration can also retard the flotation kinetics. The combination of decreased surface area of dispersed air and slower kinetics can result in reduced recovery causing coarse particles to continue to drop

Jan 1, 1989

By J. F. T. Agapito

The load carrying capacity of oil shale pillars excavated by conventional blasting, presplit blasting, and mechanical mining is evaluated. The study was based on a comparison of in-situ vertical stresses and fractures obtained from overcoring horizontal holes in the Colony Mine, Piceance Creek Basin, Colorado. Results indicate that conventional blasting causes a zone of damage approximately 3 m (10 ft) thick with low stress distributions. Presplit blasting reduces damage significantly, and increases the load carrying capacity in the 3 m (10 ft) thick zone by 5.93 MPa (860 psi). Mechanical mining causes little or no rock damage, and an increase of 9.83 MPa (1425 psi) in strength in the same 3 m (10 ft) thick zone. An example of pillar design is given showing that the use of presplit blasting and mechanical mining techniques can increase the extraction ratio by at least three and five percent, respectively, as compared to conventional blasting. It is speculated that comparable increases in extraction should also occur due to increases in span dimensions.

Jan 1, 1984

By J. Marts

Underground longwall coal mining sections are operated as sealed gobs if the coal is prone to spontaneous combustion. Sealing along the gate roads during longwall face retreat limits the flow of fresh air (oxygen) into the gob and, thus, deprives the spontaneous combustion reaction of oxygen. In a project sponsored by the National Institute for Occupational Safety and Health (NIOSH), researchers at the Colorado School of Mines have used computational fluid dynamics modeling to simulate the flow of gases in sealed longwall gobs. The models were validated using measurements and observations from the field and demonstrate that targeted injection of nitrogen along the gate roads inby the face can be used to control the size and location of explosive methane clouds within the gob and to minimize or eliminate the explosion hazard resulting from the formation of flammable methane-air mixtures.

Sep 1, 2013

By R. H. Grau

Researchers from the National Institute for Occupational Safety and Health have demonstrated that mine-wide ventilation in large-opening stone mines can be improved by using low-pressure, high-volume propeller fans and constructing stoppings in key locations to direct and control airflow. In light of these findings, a comparative study was conducted to determine if a portable diesel-powered propeller fan could per-form more efficiently for dust dilution and transport than an axial vane fan for localized ventilation. The objective of this study is to evaluate both fan types for ventilation efficiency at an underground dump/crusher facility in a limestone mine. Results showed an improvement with the propeller fan to dilute both the respirable dust and the respirable silica dust around the dump/crusher facility. Overall, an average reduction of 20% in respirable dust and silica was observed at the dump/crusher location with the propeller fan.

By O. Rielo, P. Katsabanis

Traditionally fine aluminum is not used in dry commercial explosives due to the hazard associated with aluminum dust explosions during mixing. An industrial process has been developed which enables the safe use of paint grade Aluminum with ANFO. The addition of fine aluminum particles resulted in increased velocity of detonation of ANFO compositions. Velocities of detonation, in 52mm (2 1/16 in.) diameter confined charges were 20% higher than velocities of detonation of straight ANFO. The detonation performance of fine grained ANFO was not benefited by Al at the diameter tested. Furthermore use of larger Al flakes resulted in decreased velocities of detonation. The results are compatible with the experience of Al addition to high explosives. Tests were also conducted using bio-diesel, finding no substantial difference in the performance of AN fuel explosive compositions which used bio-diesel.

Jan 1, 2009

By C. Acuña

The case is presented that the key role of frother is control of bubble size in the pulp zone. Compared to water alone, the addition of frother produces a narrower distribution and finer bubble size. An empirical model is presented for bubble size as a function of frother type using a normalized concentration. The model provides a benchmark for assessing operations. There is no agreed upon mechanism of how frothers act to reduce bubble size. Prevention of coalescence is a common explanation and this action is illustrated. The case against the 'coalescence' model alone is presented and a breakup mechanism is introduced based on pilot cell and single bubble studies. Phenomena associated with bubble shape, velocity and surface flows are used to illustrate the force associated with surface tension gradients. Breakup mechanisms resulting from this force are proposed. The concept can be extended to high salt concentrations which also promote small bubbles.

Jan 1, 2007

By Jie Zhu

Coal bumps are a special form of release of geologic strain energy that has already been one of the most dangerous hazards to underground mining safety in China. A number of coal-bump models have been developed to quantify coal failure under assumption that a bump is a kind of non-gas induced outburst. However, some technical experts in charge of micro-seismic and gas monitoring have found unusual gas emissions before and after bump, which suggests that it is possible for gas to trigger coal bumps. Considering the coal reservoir as geological body composed of the coal matrix and gas, a new model based on Lippmann?s bump model is proposed to understand the initiation of coal bumps. The redistribution zone from excavation of a roadway has been calculated and analyzed regarding its relation with mining depth. It is shown that high gas pressure may push the coal seam to overstep the critical state due to extension of the plastic disturbed zone, and this is harmful to the stability of coal seam. This model successfully explains the bump phenomena of the Xinzhouyao mine at shallow depth.

Aug 1, 2013

By C. Ramasamy

The tariff reductions on imports, as a part of on-going liberalisation process in India, has fueled competition within and outside India and has, in turn provided an opportunity to reach global markets. This change calls for quality upgrades and cost-competitiveness without impairing the environment. In this context, gas based processes, contributing to improvement in quality and environment as well as processes where controls are applied when gases inimical to environment are involved, are discussed in a remelt/cast-house scenario. The impact of such processes on fabrication cost of sheet ingot is seen alongwith consumption and cost of materials and compared with a world class standard plant in North America.

Jan 1, 1996

By D. Pawelus, J. Butra, R. Debkowski, M. Szpak

Impact of horizontal stresses on stability of underground workings in mines is a very important issue in underground mining. Identification of the initial state of stress in the rock-mass should be one of the main actions taken into account while designing and carrying out the mining activity in underground mines. The paper presents the tests on three dimensional stress pattern in Polish copper mines, owned by KGHM Polska Miedz S.A. Group, carried out in 2012. The research program covered 7 measuring stands in two mines; their average depth was about 1000 m. The main aim was to identify the values and directions of horizontal stresses in order to optimize the extraction and to improve the safety. The overcoring method with the use of CSIRO HI type probe was applied. The paper also describes the measuring technique which was developed for the purpose of specific mining and geological conditions of KGHM mines, taking into consideration the natural hazards encountered there as well as technical and operational capabilities with regard to drilling equipment. The experience gained during the underground measurements and the issue of making such measurements in underground copper mines in Poland are presented in the paper. The stress patterns obtained during the underground measurements are of application importance for the process of designing the spacing of mine workings and improving their stability and mine support selection.

Jan 1, 2015

By C. Zangerl, H. Lechner

"Large scale rock slides in deeply incised Alpine valleys are common hazards that can endanger human life, settlement areas and critical infrastructure such as highways, railways and reservoirs (Bonzanigo et al., 2007). In order to perform reliable forecasts of the behaviour of rock slides influenced by large dam reservoirs the geometry, the kinematics, the deformation behaviour and the hydrogeological situation need to be understood profoundly. Based on generic rock slide models the influence of the rock slide geometry on the stability as well as the impact of the buoyancy forces and water load of the reservoir at the toe of the slope are the main focus of this study. Various assumptions of hydraulic conductivity, groundwater conditions of the rock slide and impoundment depth of the reservoir are analysed using limit equilibrium approaches.Generally, deep seated rock slides are characterised by deformation along one or multiple shear zones where most of the measured total slope displacement localizes. Many large rock slides, especially those observed in foliated, mica-rich crystalline rock masses (e.g. paragneisses, mica schists, phyllites), do not fail suddenly or reach high velocities. Instead, many of them move slowly and reach velocities of centimetres per year or even less. Some show episodic accelerations, sometimes reaching alarming levels, but then subside to non-critical levels again. However, there is a potential that deep-seated rock slides fail rapidly, develop into far-reaching run-out rock flows, and cause catastrophic events. Whereas the role of triggers in promoting phases of acceleration is often understood, the same cannot be said regarding the kinematics and dynamic processes by which the rock slide mass decelerates, re-stabilises or accelerates to a catastrophic degree once the trigger impetus has been removed. Thus key questions of the presented work concern the geotechnical, geometrical and hydrogeological conditions under which a slowly moving rock slide is triggered to accelerate to irreversible, maybe dangerous velocities. The development of the sliding zone is generally influenced by pre-existing discontinuities such as brittle fault zones, shear and tensile fractures, foliation and bedding planes. These geological structures determine the geometry of the sliding zone which can either be rotational or translational. During the gravitationally induced failure process the geometry of the rock slide undergoes a change.Several observed post-failure geometries in metamorphic rocks show a concave topography in the middle to upper part of the rock slide and a typical convex or bulge-like topography at the toe of the slope (Zangerl et al., 2012). Whereas the sliding zone of the upper part of such a rock slide mass is rather steep and planar, the inclination of the sliding zone at the toe can be close to zero and act against the driving forces (Alonso et al., 2010). A shear zone that meets alluvial deposits at the foot of the slope encounters a stabilizing impact on the mechanical behaviour. This buttressing effect of alluvial sediments has a remarkable influence on the slope stability."

Jan 1, 2015