Search Documents

By Ralph Monaghan, Arthur Youmans

General principles of scintillation counter-type instruments for radioactivity logging are discussed and the various possible causes for instability are examined. It is shown how instrumentation problems are solved. Means are discussed for minimizing drift and instability due to "fatigue" of the photomultiplier tube and neutron activation of the crystals. INTRODUCTION Neutron and gamma-ray logs made with logging instruments employing scintillation counters are now routinely available from most of the logging service companies. The superior characteristics of scintillation counters by comparison with older types of detectors promises to bring about important improvements in quantitative interpretation of radioactivity logs. Moreover, new types of logs can be made with scintillation counters which are not possible with other detectors. But in spite of the obvious superiority of these counters with respect to efficiency, speed, and versatility, they suffer from a number of inherent difficulties and weak- nesses. Unless these inherent diffi-culties are fully recognized and satisfactorily overcome by sound engineering of the associated instrumentation, scintillation counter logs are particularly likely to exhibit drift and instability of sensitivity. This defect in logs when they are intended for quantitative interpretation is intolerable and more than outweighs any advantages over the older type of instrumentation when the latter is operating correctly. SCINTILLATION COUNTER OPERATION In general all radioactivity logging instruments consist of a detector sensitive to gamma radiation or to neutron radiation coming from the strata. This radioactivity is either due to naturally decaying radioactive elements in the rock, radioactivity induced in the rock by a neutron source in the instrument, or scattering by the rock of neutrons or gamma rays coming from a source in the instrument. In the scintillation counter the gamma radiation or neutron radiation reacts with the scintillation phosphor to produce light pulses. These light pulses are then converted to amplified electrical pulses by the multiplier phototube. Basically the problem of making a good scintillation counter logging instrument is to make the radiation sensitivity of the system as nearly constant as possible. The size of each scintillation counter pulse is dependent on the energy of the individual quantum of radiation being detected. In normal radiation logging, gamma rays of all energies, up to some maximum value, reach the detector. If a suitable scintillator is used, such as a sodium iodide crystal, each gamma ray produces a number of photons proportional to the energy absorbed by the crystal from the impinging radiation. The light flashes are detected by means of a photo-multiplier tube which contains not only a photo-sensitive cathode from which photoelectrons are collected, but also an amplifier, called an electron multiplier, built inside the photomultiplier tube; the electron multiplier usually has about 10 stages, having an over-all gain of perhaps 500,000. In an ordinary gamma-ray log one wishes to detect all gamma rays down to the lowest possible energy; therefore, one wishes only to reject the "noise" pulses which are invariably present due to thermal emission of electrons from the photo-cathode of the photomultiplier. In other radioactivity logs it may be desired to measure the radiation within a particular energy band, or above

Jan 1, 1958

By C. Scala, M. Gondouin

Published laboratory data have established that very significant streaming potentials can exist across mud cakes subjected to pressure differentials such as exist between a mud column and formation fluids. Since shale is similar in kind and in properties to a well-formed mud cake, it appeared possible that streaming potentials might also arise across shales. A practical consequence would be that the streaming potential contribution to the SP would be smaller than might otherwise be assumed since the SP is measured with respect to the "shale bare line". The resultant contribution would be the difference between the streaming potential across the shale and that across the mud cake. In order to investigate this possibility, a laboratory apparatus was devised for measuring streaming potentials under pressure conditions normally encountered in wells. Reported data on streaming potentids across mud cakes were verified. More important, appreciable streaming potentials were found across shale samples. As in the case of mud cakes, the shale potentials varied with the concentration and nature of the impregnating electrolyte. Dependence on pressure was In a different rela-tion than that for mud cakes, possibly because of the lower compressibility of shales. The differences in streaming potentials between the shales md mud cakes were generally small, although they might vary considerably in practice depending on the relative electro-kinetic properties of the particular shale-mud cuke combination. A "poorly eflective" shale with a "very eflec-tive mud cake" would produce the largest negative addition to the electrochemical component of the SP. Results of field experiments with pressurized wells were considered in the light of the laboratory results. INTRODUCTION Field experiments wherein the pressure of the mud column in a borehole was varied have often indicated the presence of a streaming potential, but its magnitude was not easily predictable and its sign sometimes changed from one formation to another in the same well.' In the interpretation of SP logs from standard surveys, nevertheless, the correct value of R,, is very frequently obtained, within the limits of field accuracy, using only the simple electrochemical expression of the SP provided that proper corrections are made for bed thickness, ion activity, etc.' Accordingly, it was apparent that the streaming potential component of the SP in a borehole was considerably more complex than commonly assumed and clarification was indeed necessary The close similarity in nature and constitution of a shale to a well-compacted mud cake suggested that a streaming potential might also exist across shales as pointed out by M. P. Tixier in 1953 and as recently emphasized by Wyllie." e practical consequence would be that the streaming potential across the mud cake would be canceled, at least in part, on electrical logs since the SP is recorded with respect to the shale potential as a base line. This appeared to be a plausible explanation for many of the effects observed but no supporting data were available. In 1955 preliminary experiments at low pressures were conducted in our laboratories which supported the hypothesis of the shale streaming potential and formed the basis for later studies at borehole pressures.* EARLY LOW PRESSURE EXPERIMENTS The early experiments were conducted primarily to determine the possibility of a streaming potential across shales. The shale used was a compact type designated as No. 7 from Reagan County, Tex. (Permian). Cut samples were saturated for over one month in .2 to 2.0-N NaCl solutions. In order to eliminate all electrode polarization effects, a dynamic method was used. A transient pressure of about 1 atm was applied across

By J. E. Drury, W. M. Byers, E. J. Lynch

Measurements made with starch ~~~~s indicate that the Presence of starch serves to depress the streaming potential of a clay mud system. Measurements with pure starch slurries show that the addition of NaCl or CaO reduces the streaming potential significantly. The addition of NaOH, however, causes only a minor reduction in potential even when there are large changes in mud resistivity. INTRODUCTION In their excellent study of the streaming potential, Hill and Anderson' proposed that the presence of conductive solids within the filter medium will reduce the generated potential. This theory was demonstrated with measurements on shaly sandstone cores having various "b" factors; the cores with the higher negative b factors showed markedly lower potentials. (The factor b was originally defined by Hill and Milburn2 in an expression relating the resistivity of a shaly sandstone to the resistivity of the interstitial water: log F, = log F,, + b (log 100R,)'. 'he factor b, therefore, is a measure of the contribution of the conductive solids to the total conductivity of the sample. It has been found experimentally to be directly related to the amount of chemically exchangeable ion per unit pore volume.) In the logical extension of this hypothesis to the streaming potential created by filtration through mud cakes, they suggested that the presence of nonconductive starch in a drilling mud would have the opposite effect; i.e., it would cause the streaming POtential to be increased. The high streaming potentials that they observed with lime muds were attributed to this cause. A cross-plot of some of their results which are relevant to this discussion is given in Fig. 1. The lime-mud curves and untreated-mud curve are taken from curves given in their paper. The gyp-mud line was estimated from their statement that the measured streaming potential for gyp muds in the range of 1.5 to 2.0 ohm-m was approximately 18 mv/1,000 psi. These gyp-mud potentials were the lowest that they reported for any of the bentonitic-clay muds, and were the only ones which were less than the untreated-mud potentials. This very low streaming potential of gyp muds has also been observed in field studies.' By way of comparison, a U. of Texas publication4 gives the approxi-ate compositions for lime and gyp muds shown in Table 1. These materials are added to a bentonitic-clay mud base. It can be seen that both of these muds contain significant amounts of calcium salts and that the gyp mud has the higher concentration of starch. It would appear from this and from the data shown in Fig. 1 that starch may well be the cause of a streaming-potential reduction, rather than a potential increase. EXPERIMENTAL A series of streaming-potential experiments has been performed using a cell of a design similar to that reported by Wyllie.5 Calomel electrodes were used in both the mud slurry and the filtrate. Pressure in the cell was generated with high-pressure nitrogen. The primary objective of the investigation was to determine the effect of starch on the potential. Five different slurries were made which ranged in composition from untreated ben-tonitic mud (Baroid Aquagel) to a pure starch suspension (Baroid Im-permex). The intermediate slurries were prepared by mixing together a 9-lb/bbl clay mud with a 12-lb/bbl starch suspension in the ratios 1:3, 1:1 and 3:1. When starch was used alone, it was necessary to use an 18-Ib/bbl mixture, since leaner mixtures would not form a suitable filter cake. The clay mud used in the experiments was aged for three months before use. In addition to this series of measurements on the starch-clay mud mixtures, other experiments were performed to determine the effect on the potential of the absolute starch and Aquagel concentration, and the effect of adding various chemicals. RESULTS The effect of starch on the streaming potential is shown clcarly in Fig 2. Increasing percentages of starch resulted in n continually decreasing

By R. J. Tailleur, M. Rosenberg

Oil well drilling muds prepared with lubricating aids such as oil, graphite or mica will not produce a sufficiently strong protective lubricant film for the bit bearing surfaces under high load conditions encountered in drilling operations. Consequently, the damage to the bearing surfaces resulting from the absence of such a film frequently results in a shortening of the drill bit life. Several different types of extreme pressure lubricating additives for use in muds have been developed. These arlrlitives are capable of providing a protective lubricating film for bearing surfaces subjected to high load pressures. A modified version of the Timken lubricant tester, an instrument commonly used for testing the extreme pressure lubricating properties of oils, is used for measuring and controlling the lubricating qualities of the mud. Comparison tests made in the laboratory with 55/8-in. tricone bits drilling on steel plates immersed in extreme pressure lubricating muds and conventional muds showed that the bearing life of those bits tested in the lrrbricating mud was three to four times greater than obtained with conventional muds. Drilling tests made with extreme pressure lubricating muds in West Texas increased over-all bit life three to fourfold, reduced drilling torque and wear on drill pipe and drill collars. INTRODUCTION Roller bit cones contain roller, ball and journal-type bearings that are subjected to very heavy loading during drilling operations in which the only lubricant available for these bearings is either water or drilling mud. These bearings must be able to operate satisfac- torily in order for the cutting structures on the surface of the cones to be fully utilized. Frequently, the bearings wear to the point that the cones freeze and the bit must be pulled before the cutting structures on the cones become worn. In some instances the bearings continue to turn with severe wear but the cones, which are held on the bit by the bearings, drop off; and this causes an expensive fishing job. In other instances the bearings wear to the point that the cones pinch in causing an undergauge hole and delays to ream the hole. The advantage of increasing bit bearing life is self-evident. Because of inability to control the internal wear of bits while drilling, it was felt that improvement of the lubricating qualities of the circulating mud would be helpful. However, the often-discussed lubricating property attributed to muds has been a rather vague and intangible one. The literature has implied that the oil-emulsion muds are more effective lubricants than non-emulsion muds. Actually, there has been no direct method of measuring the lubricating property of muds which would indicate that one mud was better than another; there has been no way to determine whether the lubricating property of any mud was adequate. Furthermore, in comparing lubricating properties of muds, two qualities should be considered—the coefficient of friction and the extreme pressure lubricating qualities. For example, graphite can reduce the coefficient of friction, but does not provide a strong enough lubricating film to protect bit bearings subjected to high loads. The primary object of the investigation reported herein was to find a method for prolonging the bearing life of drill bits; and considering the heavy loads used in drilling, it was felt necessary to find both a method of measuring lubricating properties under high load conditions and methods of establishing effective lubrication under these conditions. Extreme pressure lubrication deals with that realm of lubrication where metal surfaces are in rubbing contact with each other under very high pressures. These pressures may be quite high, as for example,

By R. L. Caldwell, E. E. Glenn, L. J. Norton, A. J. D. Straus, S. V. Holcomb, J. Zemanek

A new and unique logging tool, called the Borehole Televiewer (BHTV), has been developed to inspect boreholes and to evaluate formations. Even though geologists and engineers have had only about 3 years' experience with the BHTV, the thinking of many of them has been radically influenced by the fascinating and revealing "log-picture" recorded with the tool. The BHTV fills a need for a logging tool that can produce a direct and descriptive record of the physical properties of the borehole environment. Although primarily developed to evaluate fractured reservoirs, the BHTV has been used successfully to solve a variety of problems related to formation evaluation and borehole inspection. Geologists and petroleum engineers have been confounded for many years by the problems of locating and evaluating fractures. Interpretation of the usual resistivity, acoustic or radioactivity logs, as well as the analysis of cores, for evaluation of fractured reservoirs is extremely difficult and often not definitive. This is understandable since analysis of cores from fractured formations has reported variously: (a) low porosity, (b) no effective permeability, (c) lack of any matrix oil saturation and (d) oil stains on fracture planes as the only indications of potential production.14 In recent years acoustic amplitude logs have been introduced and used with varying degrees of success to locate fractures.8'9'11"13 Conventional amplitude logs at best give only qualitative answers where quantitative ones are desired. The logs reveal nothing of the orientation of the fractures. In addition to these logs, various types of cameras, television, and rubber impression packers have been used for borehole inspection. (See Appendix.) The BHTV logging tool supplies both the quantitative and the orientation answers about fractures. The borehole can be filled with any homogeneous, gas-free liquid such as fresh water, saturated brine, crude oil or drilling muds. This tool takes an "acoustic picture" of the borehole wall. The resulting log is a representation of the borehole wall as if it were split vertically and laid flat. The log is oriented with respect to magnetic north. Any physical changes in the borehole wall are seen as changes in picture intensity. In this way, fractures, deformation or pits are reflected on the log. Tool Description The fundamental parts of the BHTV are shown in Fig. 1. A piezoelectric transducer probes the borehole wall with bursts of acoustic energy. A flux-gate magnetometer senses the earth's magnetic field and provides the means for determining the orientation of the log. A motor rotates the transducer and mag-

Jan 1, 1970

By R. P. Alger, J. S. Wahl, C. W. Johnstone, J. Tittman

To overcome the problems of mudcake and hole irregularities, the new compensated formation density logging device employs two detectors spaced at different intervals from the source. The detector at the shorter spacing is particularly sensitive to the density of material immediately adjacent to the face of the pad. The contribution of this material, which includes mudcake and minor wall irregularities, affects the response of each detector to a different degree. The signals from both detectors are combined to give automatically a density correction which is added to the uncompensated density information from the detector at the longer spacing. Both the compensated density measurement and the amount of compensation are then recorded on the log. With the unwanted borehole effects removed, the measurement is recorded directly in terms of bulk density on a linear scale. INTRODUCTION Formation density is a very useful and diagnostic parameter for formation evaluation. When the matrix lithology is known, porosity is accurately and readily computed from density data.'-" hen the density measurements are used with other porosity-responsive measurements, such as Sonic and Neutron logs, both lithology and porosity may be defined with good accuracy."'" In the past, however, application of density logs was complicated by the need for corrections to obtain true formation densities from the log values. Mudcakes on permeable formations and roughness of the borehole walls have been particularly troublesome since, in each case, the device was prevented from direct contact with the formation. ~ttempts have been made to correct for such conditions by making a simultaneous caliper log, estimating pad standoff, and assuming knowledge of the composition of the intervening materials. While such corrections are frequently accurate, they are not always reliable because of uncertainties in the pad standoff and material composition. A further complication was the necessity for manual conversion of log counting rates to density. The newly introduced compensated formation density logging device (FDC) automatically corrects for mudcake and minor wall irregularities, and provides a log that is scaled directly in bulk density. The purpose of this paper is to discuss briefly the equipment, to explain the theoretical considerations involved in the compensation, and to present field examples of this new log. COMPENSATED FORMATION DENSITY EQUIPMENT The FDC tool incorporates two major advances over previous density logging devices: a second detector, spaced closer to the gamma ray source to provide increased sensitivity to material close to the pad; and the automatic derivation of a corrected formation density from the two counting rates. The arrangement of the source and detectors is shown in Fig. 1. The longer spacing detector is at the same spacing from the source and gives the same response as the single detector in the previous uncompensated device. By appropriate combination of the outputs of the two detectors, the FDC tool is able to compensate in large measure for effects of mudcake and hole rugosity. This is achieved, as will be described later, without specific knowledge of either the thickness or the nature of material between the pad and formation. To obtain corrected formation density, the two count rates are automatically processed by an analog computer in the surface panel. More specifically, the computer derives a value of uncompensated formation density from the long-spacing counting rate, computes a density correction p using both the long and the short spacing count-

Jan 1, 1965

By H. S. Thomsen, W. C. Duesterhoeft, R. E. Hartline

The attenuation and phase shift which formations produce in the electromagnetic field of an induction-type electrical well-logging instrument are great enough to substantially affect the response of the tool to formation conductivity under normal logging conditions. The application of the general equations for the propagation of an electromagnetic field in a conductive medium to the transmitter-receiver coil pair of an induction-logging-tool coil system gives an expression for the response which properly takes the propagation effects into account. A comparison of a calculation of this type with the response computed from the commonly used geometric factor concept, which does not include the propagation effect, leads to a factor Go representing the ratio of the responses computed by the two methods. The value of Go decreases not only with increasing formation conductivity, but also with increasing transmitter-to-detector coil spacing. For a single coil pair with a 40-in. spacing, the value of Go is 0.972 in a 20-millimho/m formation. The value is reduced to 0.915 and 0.812 for conductivities of 200 and 1,000 millimhos/m. As a result, the basic signal generated by the induction-logging coil system is not linearly related to formation conductivity as expected from the geometric factor concept. A uniform conductivity scale can be obtained only by adding a suitable nonlinear element to the recording system. The addition of auxiliary coils, having spacings less than the main-coil span, to achieve focusing results in an even greater departure of the basic signal from linearity with conductivity. The solution of the field equations near the interface between two formations of different conductivity gives the curve shape on an induction logging tool in crossing the interface. The addition of auxiliary coils to achieve focusing can add anomalous character to the curve shape in crossing the interface, which might be mistaken for lithological detail. Preliminary calculations which include the propagation effects in the determination of the conductivity correction for thin beds lead to correction factors which are substantially smaller than those obtained from geometric factor considerations. It is apparent that thin-bed corrections derived from geometric factor calculations are of doubtful validity. INTRODUCTION Although the electromagnetic induction type of electrical well log has been used for a number of years and has gained general acceptance in quantitative well-log interpretation, no technically complete investigation of the mechanism and of its operation has been published. The studies which have been presented are based upon the premise that neither the shape nor the intensity of the induction field of the logging tool is in any way affected by the electrical characteristics of the formation. From the inception of induction logging it has been recognized that under some formation conditions the performance of the instrument could be expected to be substantially different from that predicted by the simplified analysis. This anomalous performance has been called "skin effect" since it is the result of the same phenomenon which causes high-frequency alternating currents to flow only near the surface of metallic conductors. In the range of conductivities encountered in the sediments, the formation actually does not exhibit the sharply defined conducting "skin" shown by metals. The gradual modification of the distribution of the currents in the formation, produced by the induction field of the logging tool, is the direct result of phenomena associated with the propagation of the electromagnetic field through the formation. Therefore, it can be much more appropriately described as the "propagation effect". One purpose of this paper is to review the results of a solution of the equations for the performance of a single transmitter-receiver coil pair induction-logging system which takes into account the propagation effect, showing the manner in which the tool performance established by this analysis differs from that derived from the less comprehensive analyses currently in use. PRINCIPLE OF OPERATION OF THE INDUCTION LOGGING INSTRUMENT The high-frequency alternating current which is maintained at a constant value in the transmitter coil

By W. A. Nagel, R. P. Alger, H. Sherman, J. Tittmann

A sidewall epithermal neutron tool has been developed to substantially reduce environmental effects that have previously complicated neutron log interpretation. Designed for operation in uncased wells, the device provides increased accuracy in both liquid-filled and empty holes. A brief discussion of neutron moderation, diffusion and capture shows that logs using epithermal neutron detection depend on a smaller number of formation-characterizing parameters than those using thermal neutron or capture gamma ray detection. Thus, they come closer to providing an unambiguorls determination of hydrogen content. In this new device a directionally sensitive epithertnal neutron detection system has been incorporated in a side-wall source-detector skid to minimize borehole effects. The effects of variations in borehole size and shape, mud type, temperature and salinity are greatly reduced. Small residual borehole effects are then computationally accounted for in the surface control panel to provide a borehole-corrected neutron log. The log presents a direct recording of neutron-derived porosity on a linear scale. With corrections for borehole effects already applied, this direct recording of porosity simplifies log interpretation. Furthermore, comparison with a linear porosity presentation of a formation density log permits sandstones, limestones and dolomites to be readily identified. Thus, in complex or variable lithology, porosity is determined with greater accuracy and reliability than heretofore. Laboratory data and field results demonstrate the improvements in neutron logging afforded by this new side-wall epithermal neutron logging device. INTRODUCTION The new Sidewall Neutron Porosity (SNP) logging system, designed for use in uncased wells, provides reliability and accuracy never before achieved with neutron logs. The effects of variations in borehole diameter and shape, fluid salinity, mud weight and temperature—parameters that have long complicated neutron log interpretation— are suppressed or corrected for by this sidewall epithermal neutron detection system. Furthermore, to simplify interpretation the SNP log presents a direct recording of computed porosity on a linear scale. The performance improvements achieved by this new system arise primarily from the combination of two im- portant design features. First. though not unique to this new tool, an epithermal neutron detection system is used,',' Epithermal neutron detection substantially reduces the perturbing influences of the thermal neutron absorption properties of rock matrices and water salinity. Second, the neutron detection system is mounted in a directionally sensitive sidewall skid to greatly minimize borehole effects. The purpose of this paper is to explain briefy the advantages offered by the detection of epithermal neutrons, to describe the SNP equipment and the log, to present calibration and correction data and to give examples of interpretation methods made especially convenient by this new system. ADVANTAGES OF EPITHERMAL NEUTRON DETECTION Epithermal neutron detection, of all the neutron methods in current commercial use, provides the simplest determination of formation hydrogen content. Advantages of epithermal neutron detectors, as compared with thermal neutron and gamma ray detectors, are probably best explained by a brief review of the life of a source-emitted neutron. A fast neutron from the source will eventually be cap-tured by the nucleus of an atom. However. before capture is likely to occur, the fast neutron (energy of 100,000 electron volts (ev) or more) will be slowed down until it is in thermal equilibrium with its surroundings. The neutron is then considered to be a "thermal" neutron (average energy of 0.025 ev at 25C). The overwhelming majority of the slowing down thus occurs in reaching epithermal energies (energies just above thermal—0.5 to several ev). After reaching thermal energy. the neutron will "diffuse" through the formation with, on the average, no further energy change until capture. Upon the capture of the thermal neutron, relatively high energy gamma rays arc usually emitted. Hydrogen plays a very important role in the process of slowing down fast neutrons. On the other hand, the absorption effects of water salinity and low concentrations of other strong thermal neutron absorbers—relatively unimportant in the moderation process-—are very important in thermal diffusion, capture and the production of gamma rays. Thus, by detecting only epithermal neutrons with the SNP, spurious effects due to these thermal neutron absorbers are greatly minimized as compared to the effects on tools using thermal neutron or gamma ray detectors. The epithermal neutron detection system affords another important advantage. Log response in various litho-

Jan 1, 1967

By E. R. Atkins, G. H. Smith

Results of laboratory tests are presented to show that lire value of "m", in the Archie expression dernlined by the shapes of the particles in the system. Tile value of m "the shape factor", is constant for a system of particles of a given shape for a range of F - + values. Applying this concept, one can predict F - + relationships for mixtures of particles with different shapes, and these predicted relationships are useful in electric log interpretation. It is suggested that an equation of the form 1/F -10mcan be used to describe the properties of natural formations containing varying amounts of sand and clay. From this work and values of "a" and "m" reported in the literature, it appears that in many cases rocks in the same geological horizon have a common primary porosity but contain varying amounts of a particular clay. It is concluded that the equation can be applied to a rock-water system only when values of "a" and "m" have been established for the particular system. INTRODUCTION The petroleum literature contains many reports of the results obtained by determining formation resistivity factor F and porosity + of rock samples from oil fields all over the world. The usual practice is to use data from a large number of samples from a number of fields to find an average relationship between F and +. Several such average relationships have been advanced. In the absence of data on a particular formation or field, it has been the practice to use the average relationships to give a rough approximation of the F - + relationship. The purpose of this paper is to report on basic relationships that exist between F and + for naturally occurring particles in water solutions. Other workers' have found the same relationships apply to the diffusion of hydrogen through packed beds of dry particles. In the work discussed here, relationships for application to unconsolidated sands or shales containing mix- tures of particle shapes are derived. These relationships, developed for unconsolidated formations, may apply to consolidated formations. EXPERIMENTAL To evaluate F- relationships for unconsolidated rocks, the results of laboratory measurements on simple slurries of clay or sand will be used. Such laboratory studies are concerned with the electrical behavior of water-containing rocks. The wet rock constituents are electrically similar in slurries and in rocks. Archie2 defined formation resistivity factor as All resistance measurements were made using a 1,000-cycle impedance bridge with an oscilloscope as the null detector." The accuracy of this bridge was better than * 0.15 per cent. For the particular apparatus employed, no additional reactance was required to achieve balance for samples with resistances between

By M. L. Millican

The objective of this study has been to develop a method of log interpretation in the Delaware sand whereby the effects of the shale contained within the sand can be recognized and accounted for in a quantitative solution for porosity and water saturation. Both theoretical and empirical considerations are discussed. A simplified interpretation chart is presented which provides a means of amending the conventional porosity resolution of the Sonic log to compensate for the presence of shale. The amount of shale within the sand and its degree of lamination may be inferred from a calibrated gamma ray log. The resulting porosity value may then be used in conjunction with a knowledge of the formation resistivity to determine water saturation. Of added interest, particularly in the Delaware sand, is an approximation of permeability which may be derived empirically from the simplified chart. The discussion is illustrated by field examples. INTRODUCTION The performance of the Sonic log in defining the porosity fraction in clean, consolidated formations is well known, particularly in sandstones that are well compacted and free of shale. An approach to Sonic log porosity determination in shaly sands has been recently developed.' This method involves correcting the Sonic log readings by means of an a factor, where a is the ratio of the pseudo-static SP to, the static SP, and is a function of the amount of shale present. This method is dependent upon a contrast between the salinities of the drilling fluid and the connate water in the formation, inasmuch as this contrast produces the SP effect. In wells drilled with salt mud, the contrast, and with it the means of obtaining the a correction, disappear. In the Delaware basin, the large majority of rotary wells drilled to the uppermost sands of the Bell Canyon group employ salt mud as the drilling fluid. These sands have been the objective of most of the drilling exploration in the basin to date. A comparison of porosity values in these sands, as determined by core analysis, to Sonic log readings has indicated that a correction for the shaliness of the sand is needed. In the absence of an SP curve to determine the correction factor, the porosity resolution of the Sonic log in these sands has been questionable.

By A. A. Stripling

The Cretaceous limestone wells of the Mara/Maru-caibo Dist. of Venezuela are extremely prolific producers. To maintain production on cessation of natural flow, large scale gas-lift operations were commenced involving high production rates on caring Flow. For the design of these gas-lift installations it was essential to have some knowledge of the pressure gradients involved in casing flow, so that the required injection pressures, optimum gas injection raws, etc., could be forecast. This paper presents a method of calculating these annular pressure gradients. Basically the method makes use of an energy balance equation coupled with an empirical energy loss factor derived from field data. The calculations have been put in a form suitable for "punch card-type" calculating machines. A set of gradient curves for Mara/Maracaibo conditions covering flow rates up to 12,000 B/D, and GOR's of 500 to 2,000 cu fd/bbl is presented. From these curves the flowing BHP can be predicted from surface data and the vertical pow performance under varying conditions of gas injection can be estimated. The method has been applied to La Paz and Mam gas-lift operations for over three years and has given consistently accurate results. INTRODUCTION The Cretaceous limestone fields of the Mara/Maracaibo area in Venezuela are characterized by the presence of widely distributed fissure systems. Under these conditions individual wells frequently have extremely high potentials and such wells are generally flowed on the casing-tubing annulus in order to reduce the pressure loss in vertical flow. To maintain production on cessation of natural flow, an extensive gas-lift system was planned. As a first approach to this gas-lift design problem, an attempt was made to construct a set of empirical flowing gradient curves from the available subsurface pressure data. Such a method has been used successfully for tubing-flow conditions in California by Gilbert'. Unfortunately, the empirical construction of casing-flow gradient curves presents additional difficulties, as pres- sure bombs cannot bc run in the casing-tubing annulus against high rates of flow. Thus, the Full flowing gradients cannot be defined by actual measurement and the best that can be done is to obtain spot pressures at the tubing shoe. Under these conditions a vast accumulation of BHP data is required to construct a set of gradients. To the La Paz and Mara fields the majority of the available flowing pressure measurements fall into a relatively narrow GOR range, in the neighborhood of the solution ratio. While there appeared to be reasonable prospects of constructing gradient curves for this limited range, measurements at higher GOR's, which were of major interest for gas-lift operations, were relatively few and the prospects of constructing empirical curves cor~spondingly remote. As an alternative approach, the possibilities of a mathematical analysis of vertical flow conditions were investigated. May and Laird2fV n 1934 presented an excellent analysis of the vertical-flow conditions in the Anglo-Iranian Oil Co.'s fields. Their analysis was based on an energy-balance equation and calculated the losses due to kinetic energy, friction and slippage separately. By combining these losses with the total calculated available energy, the required depth-pressure traverse could be deduced. On applying the method to La Paz conditions, good results were obtained for tubing flow at high tubing-head pressures. However, for lower wellhead pressures (300 psi and under) the discrepancy between calculated and measured values increased appreciably. It was considered that this was probably due to energy losses caused by slippage or liquid hang-up in a continuous gas phase, for which it was difficult to visualize any analytical approach. In 1952 Poettmann and Carpenter4 presented a method of pressure gradient calculation which, while based on an energy-balance equation similar to that employed by May and Laird, made no attempt to evaluate the various components making up the total energy loss resulting from irreversibilities of flowing fluids. Instead, they proposed a method of analysis which assumed that all significant losses for multiphase flow could be correlated in a form similar to that of the Fanning equation for frictional losses in single-phase flow. They then derived an empirical relationship linking measurable field data with a factor which, when applied to the standard form of the Fanning equation, would enable the energy losses to be determined. The total available

By W. A. Hoyer

Neutron activation analysis for mineral identification has attracted the attention of numerous investigators, judging from the publications on this subject in the past few years. 1-9 The appealing aspect of this method of mineral analysis is its proven sensitivity in the laboratory. In principle, activation analysis is one of the few petro-physical methods whereby a direct analysis for a mineral itself is possible in a borehole. The successful application of activation analysis requires the use of particular neutron reactions, measurement of selected gamma-ray energy intervals, and optimum bombardment and detection times. For copper analysis, Labanov et al., 10,11 using a low-energy PuBe source, reported an acceptable logging means. On the other hand, Pradzynski12, in analyzing ores and process tailings, used high-energy neutrons and photons for surface measurements of process samples. The work of Labanov et al. was based on measuring the rate of decay of the activated copper and hence was not as definitive as might be desired. Equipment is commercially available to carry out activation studies in the field 13,14 Gamma-ray spectra can be successfully transmitted over ordinary logging cables and, with borehole high-energy neutron accelerators and lower-energy chemical neutron sources, a variety of neutron activation methods can be studied. The purpose of the study discussed in this paper was to determine the feasibility and practicability of logging for copper using neutron activation techniques and commercially available equipment. The laboratory study showed that Cu could be detected in rock samples in the laboratory by high-energy neutron activation of 63 Cu. In the field, however, due in part to the large volume irradiated, the direct detection of copper using high-energy neutrons was not as promising. Detection of copper by measuring both the direct gamma-ray emission and the excessively strong low-energy gamma-ray absorption appears promising. Copper was not detected either in the laboratory or

Jan 1, 1972

By W. A. Hoyer, G. A. Lock

Laboratory and field tests have shown that it is feasible to log for copper in a qualitative way using the techniques of neutron activation analysis. Laboratory tests showed that the 0.51 and 1.04 mev gamma rays of 62Cu and 66Cu, respectively, could be diagnostic. However, in the core holes, the detection of copper was limited to 0.3% concentration because of interferences from the 18Si and Al gamma rays. Both stationary and continuous logs were made, but only the stationary data yielded a recognizable copper response. This response consists of a combination of two effects-the direct response from copper at 0.51 mev and an increase in low energy gamma ray absorption due to mineralization. Both low energy chemical (PuBe) and high energy accelerator neutron sources were used for the laboratory and field tests, while the same 2 X 5 in. Nal scintillation detector served for all the tests. Potential improvements in copper detection might be possible with solid state gamma-ray detectors which have better gamma ray resolution but much less detection efficiency. This type of activation logging requires complex equipment and trained personnel to conduct field operations and may find application where coring is difficult or prohibitive.

Jan 1, 1973

By J. A. Franklin, E. Broch, G. Walton

To make the best use of rock core, the mechanical character of the rock should be evaluated concurrently with conventional geological observations. The advent of simple techniques, such as the point load 'nutcracker' test, makes field logging of mechanical properties competitive with sampling and testing in the laboratory

Dec 1, 1971

By R. Simard

"Conventional exploration strategies identify many mineral deposits as potentially interesting, although only a few of them turn out to be of economic importance. In the context of exploration for sulphide nickel deposits in the Canadian Shield, a decisional model, based on a statistical study of parameters relative to nickel deposits as well as to barren sulphide occurences, has been developed.Because such geophysical variables as gravimetry, aeromagnetism and topography could be related to the relative importance of nickel-bearing deposits, a statistical analysis of 13 such variables was carried out for 98 targets which were considered promising after conventional exploration. Among these 98 targets are36 sulphide nickel deposits in the Canadian Shield and 62 drill-tested non-economic occurrences. The results of this study led to the development of a linear logistic model that permits evaluation, for each of the targets, of the probability of finding a nickel deposit of potential commercial interest. This decisional model can thus complement conventional exploration strategies.RésuméLes stratégies conventionnelles d'exploration définissent un très grand nombre de cibles comportant un inténet minier potentiel dont seules quelques-unes correspondent à des gisements économiquement importants. Dans Ie cadre de l'exploration des dépôts nickélifères du Bouclier Canadien, nous avons défini un modelé de décision fonde sur l'étude statistique de divers paramètres relatifs tant aux gisements d'importance qu'aux cibles dites stériles.Ayant fait l'hypothèse que certaines variables géophysiques (gravimétrie, aéromagnétisme et topographie) peuvent suffire à fournir des indications sur l'importance relative d'un gisement nickélifère, nous avons entrepris l'analyse statistique de 13 variables évaluées sur un échantillon de 98 cibles considérées comme potentiellement intéressantes par les stratégies conventionnelles d'exploration. Ces 98 cibles se composent de 36 dépôt nickélifères d ‘importance recontrés sur tout Ie Bouclier Canadien et de 62 cibles stériles reconnues par forage. Nous avons défini à l'aide de ces données un modèle logistique linéaire. Ce dernier nous permet d'évaluer pour chacune des cibles les chances de trouver un gisement. Ce modèle de décision peut done s'inscrire comme outil complémentaire aux stratégies conventionnelles d ‘exploration."

Jan 1, 1980

By Emmanuel John M. Carranza, Martin Hale

Abstract- An application of logistic regression to mapping of gold potential in the Baguio district of the Philippines is described. Categorical map data such as lithologic units and proximity classes of curvi-linear features, based on spatial association analyses, are quantified systematically and used as independent variables in logistic regression to predict the probability for presence or absence of gold mineralization. Regression experiments to compare between using all independent variables that are associated spatially with the response variable and using only statistically significant independent variables are performed. The results of the regression experiments are similar; however, the use of all independent variables produces slightly optimistic results but better prediction rates for the known gold deposits in the test district. At least 68% of the ‘model’ large-scale gold deposits and at least 76% of the ‘validation’ small-scale gold deposits were predicted correctly. The predicted geologically favorable zones are also similar to delineated geochemically anomalous zones. The technique presented using logistic regression as a data integration tool is effective for geologically constrained technique of mapping mineral potential.

Jan 1, 2001

By Frank Hirthammer

Productivity, customer relations, and effectiveness of work depend to an ever-increasing extent on a functioning logistics system tailored to the needs of the user. Of course, it is not possible to cover and explain all aspects of the logistical requirements of even a small part of an industry, in a single article. The article speaks specifically about the particularities and differences in the logistical requirements in the explosives sector. Starting with questions of safety, handling and quality up to the legal basis, there are special requirements regarding the logistics in the explosives sector. The results of innovative logistics solutions are presented using three examples from daily work practice.

Jan 1, 2019

A combination of the needs of business, employee desires and safety and health considerations is stimulating increasing attention to the time spent by people at work and the timing of that work. Particularly we are seeing: - innovative work schedules for 24-hour mining businesses; and - response from industry to accommodate the needs, even the desires, of employees in return for systems which are more productive and more capital efficient. There appears to be an evolutionary trend for business management to become more sophisticated and responsive to the need for achieving close to best cost work schedules to sustain continuous improvement. The underlying motivating forces driving this trend for improved techniques in organising attendance at, and time spent at work, is the seemingly inseparable combination of technological advance and ever-increasing accumulation of capital. The mining industry has not remained untouched by this thrust for ever-increasing need for best use of labour, to adopt advances in technology and to provide attractive opportunities for putting accumulated capital to work. An essential component of this on-going thrust is a substantial effort by the mining industry to improve the performance of labour by providing most-productive work schedules.

Jan 1, 1996

By M. Sengupta

Surface mining in arctic regions is characterized by many unique problems. Continuous and discontinuous permafrost (perennially frozen ground) occurs in most of the arctic and subarctic areas. Permafrost presents special problems of slope stability. Stability of permafrost depends on its temperature, moisture content and material type. Permafrost slope fails due to solifluction, disturbance of ice rich slopes, and liquefaction. Drilling and blasting of frozen ground present special problems. Depending on their degree of saturation with water, freezing soils and rocks have a number of important characteristics that affect blasting efficiency. Metals used in mining equipment and mining structures require special selection. At low temperatures many steels lose most of their normal ductility and toughness (resistance to brittle fracture). The paper discusses engineering solutions to unique problems of arctic mining.

Jan 1, 1986

By Justo Germán Ramón Rojas

El presente texto describe la importancia de la gestión de seguridad en valor y ventaja competitiva de la empresa para así disminuir las pérdidas económicas causadas por los siniestros, accidentes y daños a la salud del trabajador. La forma de evaluación de la cultura de seguridad es mediante los indicadores de clima y cultura de seguridad y el trabajo responsable y comprometido del equipo de SSO.

Mar 1, 2013