Search Documents

By H. W. Hitzrot

SEPARATING a mixture of particle sizes of material suspended in a liquid medium is by no means an exact science. Selecting machines for individual classifying operations is even more difficult. The plant operator's own background is of course invaluable, and considerable help may be obtained from technical articles, talks with sales engineers, and handbooks on ore dressing. These several sources of information, however, are difficult to marshal in proper perspective for the major decision on classification units that an operator may be called upon to make. To the present writer's knowledge this assembly of facts is not available in handbooks, and technical papers are scarce on classification equipment developed in the past five or six years. It is believed that this paper will be helpful to users of classification equipment at this particular period in the development of hydro-classification. For easy reference the following classification units now available and in use in metallurgical and industrial operations are listed below, with a brief description of each. Unit-type classifiers, bowl classifiers, and bowl desiltors are all rectangular tanks, slightly tilted, with reciprocating rakes or screws to remove settled sands. The unit-type classifier, Figs. 1 and 2, is available in widths from 14 in. to 20 ft and lengths up to 40 ft. The shallow bowl of the bowl classifier, Fig. 3, equipped with rotating rakes, is superimposed on the lower end of the tank. Reciprocating rake compartments for this design range from 18 in. to 20 ft wide. Bowl diameters vary from 4 to 28 ft. The flat-bottomed bowl of the desiltor, Fig. 4, of relatively large diameter, is equipped with rakes rotating outward and partly over a pit, which is created by extension of the rectangular tank into and under the bowl section. Bowl desiltors are available with reciprocating rake sections 4 to 20 ft wide and bowls from 20 to 50 ft in diam. The bowl desiltor is used for applications beyond the range of the bowl classifier. The hydroseparator, Figs. 5 and 6, is a circular tank equipped with slowly rotating rake arms, set on a slope, with interrupted rake or spiral blades to move the settled solids to a central discharge cone. Tank diameters vary from 4 to 250 ft. Tank depths at center are 2 to 3 ft for small units and up to 25 ft for larger units. Hydraulic classifiers of the sizer and super-sorter types, Figs. 7 and 8, are narrow, deep, rectangular tanks divided by vertical baffles into a series of pockets. Hydraulic water is added near the bottom of each pocket. Perforated constriction plates, spiral flow arrangements, or jets are used to disseminate the water under pressure (hydraulic water) throughout the bed of material in the pocket. Discharge valves on each pocket are operated automatically by a pneumatic mechanism, a pincer-type mechanism, or a pressure control and motor combination actuated by a hydrostatic tube within the pocket. Hydraulic classifiers are available in 4, 5, 6, and 8-pocket units of varying constriction plate areas to suit conditions. There is now a jet sizer of unit pocket design that can be made up in 1 to 25 sections or more to accommodate sizing requirements. The hydroscillator, Fig. 9, is a rectangular tank set on a slope of 3 to 4 in. per ft. A bowl is superimposed on the lower end. The bowl bottom is an oscillating rubber-covered disk, perforated to allow hydraulic water introduced beneath the disk to set up a teeter bed and thus produce an oversize or rake product exceptionally free of slimes, and material minus the mesh of separation. A shallow dam at the periphery of the bowl allows the coarse or oversize fraction to spill over and drop down into the tank compartment, where it is moved up the deck by reciprocating rakes. The material, minus the mesh of separation, overflows a circular and stationary weir which is several inches higher than the dam on the oscillating disk. It is carried off in a circular launder in the usual manner. These units are available in bowl diameters from 4 to 14 ft and with reciprocating rake compartment widths to suit the tons per hour to be handled. Centrifugal classifiers include the solid bowl centrifuge and the cyclone classifier. The solid bowl centrifuge, Fig. 10, consists of a truncated cone fixed to a horizontal shaft and rotating at high speed. An internal spiral rotating at slightly less speed continuously removes solids deposited on the inner surface of the cone, or bowl. Feed enters the cone by means of the hollow center shaft. Overflow leaves through ports at the large end of the cone, and oversize solids, moved by the spiral, exit through ports at the small end. Centrifugal classifiers of this type are available in cone diameters from 18 to 54 in. The cyclone classifier, Fig. 11, is a stationary cone having a cylindrical upper section and a lower cone section. Feed is introduced tangentially into the upper cylindrical section under pressure from a hydrostatic head or by means of a pump. Centrifugal force thus induced effects a classification within the cone, the fine sizes being carried off in the overflow through an opening at the top of the cylindrical section. Coarse solids at relatively high pulp density exit through a control valve at the apex of the lower cone section. Cyclone classifiers are available in 3, 6, 12, 14, 24, and 30-in. diam. The cone classifier, Fig. 12, is a steel-plate cone with sides usually about 60" from horizontal. It contains no rotating mechanism. Feed enters a feed-well at center and classification is effected by gravity and pulp density. Fines are carried off in the flow over a peripheral weir at the top of the cone. Settled solids exit through an opening at the apex. An apex valve actuated through levers and rods by the pulp density in the lower cone section is usually supplied. Diameters are usually maximum at 8 ft.

Jan 1, 1955

By D. C. Seidel, E. F. Fitzhugh

The Colorado School of Mines Research Foundation has developed a hydrometallurgical process for recovering nickel from oxidized ores, including both the iron-rich laterites and magnesium-rich, soft silicates. Known as the HSO-HTCP (Hydrothermal Sulfidization Oxidation-High Temperature Cementation in Pulp) Process, the system consists of feed preparation, sulfidization, oxidation, precipitation (cementation), and calcination and melting. This paper deals primarily with the sulfidization and oxidation phases of the process. Nickel sulfide ores lend themselves readily to concentration before smelting or pressure leaching, but neither of the major oxidized ore types — the iron-rich laterites and magnesium-rich, soft silicates-has been directly concentrated. Upgrading of crude ore in current practice is limited to cobbing lumps of the harder, lower grade rock (protore) from the softer, enriched silicate ore, because only a small percentage of the nickel in these ores occurs in discrete, contrasting mineral particles. There is no apparent mineralogical contrast in the superficial, iron-rich lateritic ores and, in fact, there is no firm assurance that the nickel atoms are within the lattices of the limonite minerals, or else irregularly adsorbed on the limonite. Within underlying, "rotten rock" silicates, occasional veinlets of gamierite and related nickeliferous silicates are found.' The gamierite veinlets, however, are only incidental, and the majority of the nickel atoms occur as erratic replacements of magnesium atoms in the micaceous chlorites of the ore mass. Pyrometallurgical processes account for nearly all the nickel currently being recovered from oxidized ores. Plants in New Caledonia, Oregon, Japan, Brazil and Greece smelt the ores to make ferronickels or a sulfide matte,2 and the ammoniacal leaching3 at Nicaro, Cuba, is preceded by a reducing roasL4 The only fully hydrometallurgical installation has been the politically ill-fated Freeport Nickel Co. enterprise, and this process was limited to lateritic ores.5p6 A hydrometallurgical technique which might handle both laterite and the typically richer silicate ores has been an enticing goal. The technique described here was developed at the Colorado School of Mines Research Foundation, Inc. on behalf of the Republic Steel Corp. It uses sulfur, heat, air and metallic iron to recover nickel from these ores. Inasmuch as the ores are treated as aqueous slurries, the cost of drying a plant feed that normally carried 30% or more moisture is eliminated, and there are no dust problems. Patent applications have been filed by Republic Steel Corp. on the procedures used for getting the metal into solution and on the subsequent recovery without liquids-so l ids separation of the slurry. It is referred to as the HSO-HTCP Process (Hydrothermal Sulfidization Oxidation — High Temperature Cementation in Pulp). THE PROCESS FLOWSHEET The results of various experimental studies have been combined to form the continuous flowsheet illustrated in Fig. 1. This flowsheet serves as a general pattern showing the sequence of the operations which include: (1) feed preparation; (2) sulfidization; (3) oxidation; (4) precipitation (cementation); and (5) calcination and melting. This paper deals primarily with the sulfidization and oxidation phases of the process. Feed preparation: In general, the silicate ores can be considered as earthy rather than hard, and preparation might be carried out before the addition of water in a trommel, or with water in a scrubber or log washer. This breaks up the earthy particles, allowing the hard lumps to be separated by screening. The oversize material from most ores is relatively barren and may be discarded. If there is occasion to control the iron-magnesium ratio in the plant feed, laterite, which normally breaks up readily into fine sized particles, and silicates are mixed in suitable proportions. The fine product slurry from the initial steps is mixed with elemental sulfur and fed to a conventional ball mill, although the amount of actual grinding that takes place is relatively small. The object of milling is to complete the disintegration to natural particle size and to produce an intimate mixture of the ore and elemental sulfur. This pulp, which is almost entirely -200 mesh, has a pH of about 7.0 and normally can

Jan 1, 1969

By M. E. Wadsworth, J. S. Cho

The kinetics of silicate adsorption from aqueous colloidal (SO2 . nH2O) silicate sols on thoria (ThO 2) surfaces were determined at 100, 150 and 200°C in an autoclave system. The amount of chemisorbed silica on the thoria surface was determined by means of infrared spectroscopy. First order kinetics were observed in all cases with the anomalous result that the first order rate constant was found to vary with the initial amount of silica added to the system. These results have been correlated quantitatively by means of a strain model of adsorption involving two types of surface silicate bonding, both of which may be readily observed in the infrared spectrum. Initial adsorption occurs rapidly to produce one type of surface silicate followed by a slow transition to a second type of surface bonding, the latter transition representing the slow step in the adsorption process. Initial interest in silicate adsorption on thoria arose from the dispersive effect silica has on finely divided thoria in aqueous suspensions. Spaepen et al studied the equilibrium adsorption of silica on thoria and noted increased adsorption up to approximately 215°C with a notable decrease in adsorption at temperatures above 215°C. Similar results were observed by Cho and Wadsworth2 who identified two types of surface silica by infrared spectroscopy. At temperatures of 100°C and above, rapid initial adsorption occurred producing a surface species with maximum infrared absorbance at 9.4 After extended periods of time, the 9.4 species converted to a more strongly bonded surface silicate with maximum infrared absorbance at 10.3. The latter was very strongly bonded and difficult to remove by desorption in hot distilled water, while the 9.4 species could be removed more readily by similar treatment. The 9.4 and 10.3-p species were distinguishable from free unadsorbed silica which had maximum infrared absorbance at 9.1 The kinetics of the formation of the strongly chemisorbed silica (10.3) on thoria as determined by infrared examination are presented in this study. EXPERIMENTAL PROCEDURE As a source of silicate, Ludox SM (16.36% SiO2) or Ludox HS (30.25% SO2), DU Pont colloidal silica in aqueous suspensions, was added directly to a thoria slurry made up of one liter of distilled water and one gram of thoria. The thoria used was designated D-16-650 and was received from the Chemical Technology Div. of Union Carbide Nuclear Co. It was prepared by firing thorium oxalate at 650°C. The D-16 thoria had a surface area of 32.4 ± 0.6 sq m per g as determined by nitrogen adsorption.* This thoria 'Determined by Unlon Carbide Nuclear Co., ORNL. had a total adsorption capacity for silicate of approximately 19.4 mg of silica per gram of thoria.1 This amounts to approximately one SiO2 molecule for every surface thoria site. In all cases in this study.

Jan 1, 1963

By M. E. Wadsworth, W. H. Dresher, W. M. Fassell

HIGH temperature-high pressure techniques have long been used to great advantage in the organic chemical industry, the petroleum industry, and the paper industry. Only recently, however, have these methods been used to extract metals from their ores on a commercial scale. The Chemical Construction Corp., together with interested producers of nickel and cobalt, has done much to develop methods of producing nickel and cobalt powders by the use of high temperature-high pressure techniques.' The Howe Sound Co. is currently operating a plant near Salt Lake City in which the new Chemical Construction Corp. technique is applied to cobalt-arsenic sulfide concentrates. In this method the concentrates are leached in a dilute solution of sulfuric acid under air pressure at a high temperature. Near Edmonton, in Alberta, Canada, the Sherritt Gordon Co. is also using the new method in conjunction with its ammoniacal leach process.' National Lead Co., at Fredricktown, Mo., is operating a process similar to that of Howe Sound. In spite of the rapid growth of high temperature-high pressure hydrometallurgical processes, there has been very little work done on fundamental principles involved in this type of process. Conse- quently the literature lacks any significant data in this field. Oxidation of pyrite,3 sphalerite,4 galena," and recently molybdenite" in alkaline solutions has been reported to some extent. This investigation was initiated, therefore, to broaden the application of high temperature-high pressure hydrometallurgy and also to contribute some insight into the basic mechanisms of oxidation in an aqueous medium under these conditions. In addition to the immediate consequences of these processes much valuable information remains to be learned about fundamental reactions when they are carried out at temperatures and pressures slightly higher than those normally encountered. Leaching of molybdenite by alkaline solutions under oxygen pressure has recently been reported in the Russian literature by E. S. Usataya,6 ho found that leaching rate increased with an increase in the pH of the solution—the strongest effects being observed at a pH of 10—and also with an increase in temperature. Usataya also has reported the formation of a protective film on the surface of the molybdenite when the leaching solution was weakly alkaline, neutral, or acidic. He believes that this oxidation process explains the migration of Mo++ in the oxidation zones of molybdenite ore deposits and the subsequent impoverishment of the ores. Equipment: The high temperature-high pressure reaction unit used in this work was especially designed for kinetic studies of this nature, emphasis being placed on accuracy of measurement and precision of control. As details of the unit's construction and operation have been discussed elsewhere,' only basic features and principles of operation will be discussed at this point.

Jan 1, 1957

By G. Mempel, D. C. Yang, D. W. Fuerstenau

This paper describes details of the design and operation of a batch tumbling mill which has been used for a number of years in the laboratories at the University of California. In order that the energy expended for grinding can be measured accurately, this specially constructed laboratory mill has sensitive torque measuring apparatus. Torque measurements are given for a variety of conditions with this particular mill. In recent years, there have been numerous and fairly extensive investigations of grinding in tumbling mills reported in the literature. Most of these investigations have been carried out in mills with widely differing dimensions. As a result, comparison of results obtained from various investigations has been virtually impossible. If similar mills were used by different investigators, a considerable step forward would be taken in grinding research. A specially constructed laboratory mill with sensitive torque measuring apparatus has been used for a number of years in the laboratories of the University of California. The purpose of this paper is to describe details of the design and operation of this batch tumbling mill so that other researchers, who might be interested in obtaining data for intercomparison, could construct a similar device for their own research. Furthermore, since torque instrumentation is quite expensive, torque measurements are given for a variety of conditions with this particular mill so that those who may not wish to duplicate torque measuring apparatus can make reasonably accurate torque estimates merely by duplicating the loading conditions. It is not intended in this paper to present theoretical derivations of energy consumption in ball mills. This has been done e1sewhere.l-3 CONSTRUCTION OF THE MILL In order to eliminate rust problems with wet grinding, the mill and grinding media are made of stainless steel. The mill shell was rolled from 1/2-in. steel plate. The inside dimensions are 10-in. diam and 11-1/2-in. length, similar to the mill used by Charles.4 It is equipped with eight lifter bars (1/4-in. in height) whose dimensions are given in Fig. 1. The lifter bars have been bolted into the shell so they can be removed for experiments without lifter bars; however, all data presented here are for the mill with lifters. One end of the mill is fitted with two 1/2-in. diam removable plugs for filling the mill with liquid for wet grinding experiments. The mill is mounted on ball bearing rollers as can be seen in Fig. 2. The pillow block bearings are single-row self-aligning sealed ball bearings with 1-1/4 in. hole diam. The bearings supporting the mill shell are single row sealed ball bearings with

Jan 1, 1968

By D. J. Freeh, W. E. Horst, R. C. Kellner

This paper is concerned with the description of grinding characteristics in a batch grinding system. A mathematical model was developed and used for simulating the system on an analog computer. A general equation describing the change of selected size fractions with respect to time is presented. The empirical verification of the model is discussed. In order to understand the performance of a grinding system, it would be desirable to have a mathematical description of the system's behavior. The development of a mathematical model to describe the performance of a batch dry-grinding operation was investigated. This is the first step toward reaching the objective of a practical mathematical description of a grinding system that could be employed for process control and optimization of a simple or complex grinding circuit. Although this article is concerned only with batch grinding performance, experimental work is being conducted to extend the model to continuous grinding systems. BASIC PROCESS CONSIDERATIONS In a paper dealing with the probability theory of wet ball milling, Roberts1 correlated the rate of change of oversize material, C, with energy input, E, as follows where the energy input is expressed in power/unit mass and k is a constant for each particle size. Experimental grinding studies were made by Bowdish2 to extend the previous work of Roberts. The work of Bowdish also showed that the rate of breaking of oversize particles in a ball mill is proportional to the concentration of oversize particles present. He further demonstrated that breaking of oversize particles is proportional to the surface area of the balls used for grinding. Rate equations were presented and it was concluded that grinding could be considered as a first order phenomenon according to the rate equation [2] di which is in accordance with Eq. 1. In Eq. 2, the effect of ball area is included in the constant k,. Other rate equations were reported to show the effect of a change in ball area and removal of fines during grinding. Correlation studies made by Arbiter and BhranY indicate a first-order rate equation for quartz; however, their data showed less than first-order rates existed for some of the other materials evaluated. More recently Kelsall4 has shown that the rate of breakage of any narrow size range of quartz could be described by a first-order rate equation. Several other investigators5-7 have described grinding behavior in terms of rate equations or kinetics. In general, the rate equations have been described for each particle size; however, the interactions between sizes and the overall relationships that exist have not been considered, at least not in the form of solving a group of simultaneous differential equations. Extensive work has been conducted by various investigators using a probabilistic approach which has expanded stein's' earlier work. Selection and breakage matrices are incorporated in the probabilistic model as contrasted with the deterministic method presented here. A batch grinding operation may be considered as an unsteady-state process from the standpoint that the conditions within the mill are a function of time. Therefore, a plot of mass fraction of the i-th size versus time would give a set of curves as shown in Fig. 1. In these curves X , represents the mass fraction of large size material, X2 intermediate size, and X3 small size material. An examination of these curves shows a strong similarity to the curves that would be obtained from a chemical reaction of the type9 A?B?C, [3] where A would be comparable to the largest size material being broken to an intermediate size, 3, and

Jan 1, 1968

By R. B. Adair, J. S. Browning

The Bureau of Mines conducted laboratory research to determine the applicability of heavy liquid separation to the evaluation of certain mica ores and plant products. After careful standardization of the particular mica ores and associated gangue, accurate analysis of muscovite content could be obtained from results of heavy liquid separation. Where applicable, the method should be particularly suited to the analysis of ores and control of plant operations wherein savings in time would be of considerable advantage. Specifically, there are many instances where a quick plant control method should enable the production of a more uniform grade of mica concentrate. The laboratory use of various heavy liquids for separating minerals of different specific gravities has been recognized for many years.1-8 Sink-float procedures have proven their utility as a rapid and moderately accurate means for determining the mineral content of ores, test products, and plant products in certain nonmetallic concentrating operations. A standard method of analysis for mica in ore samples has not been published or generally accepted by the mica industry. Recently, the U.S. Bureau of Mines investigated methods for analyzing mica by heavy liquid separation. This report has been prepared to make the methods available to others who may need simple, relatively rapid methods of determining the mica content of ores and plant products. The heavy liquid method of mica determination has recently been adopted by one of the major mica producers for evaluating exploration and mill control samples. DESCRIPTION OF THE ORES AND HEAVY LlQLllD The weathered mica pegmatite ores used in the investigation were obtained from commercial mica op erations in Alabama, Georgia, and North Carolina. The major mineral constituents of the ores were muscovite, quartz, kaolin, and minerals of the feldspar group. The ores also contained minor quantities of biotite, limonite, and tourmaline. A comparison of the specific gravities of the major constituents of the ores (muscovite 2.76 +, quartz 2.65, kaolin 2.61, and feldspar 2.57), indicates that an effective separation of muscovite from the other minerals can be made in heavy liquids at a specific

Jan 1, 1968

By R. W. Smith, R. J. Charles

Fractions of glass particles in the size range 0.5 to 5.0 were prepared by an elutriator that operates in a centrifugal field. Although mean sizes of commercially graded abrasive powders were ten times greater than those of samples prepared by the elutriator, frequency size plots for elutriator samples compared favorably. Efficiency of separation was low and amounts of material recovered by the elutriator were small, but the method should find use in preparation of small amounts of sized materials for laboratory investigations. R. W. SMITH, Junior Member AIME, Research Assistant, Dept. of Metallurgy, Massachusetts Institute of Technology, is presently with Portland Cement Ass'n., Chicago. R. J. CHARLES, Junior Member AIME, formerly Assistant Professor, Dept. of Metallurgy, Massachusetts Institute of Technology, is Research Associate, Ceramic Studies Section, General Electric Co., Schenectady, N. Y. TP 4261B. Manuscript, Jan. 31, 1956. STUDY of light adsorption, reaction rates, electro-phoresis, particle packing, and corrosion is hindered by lack of a suitable method of preparing small amounts of closely sized materials in the micron and submicron range. Most fractionation methods depend on some form of particle movement through a viscous media in which velocity of a par-

Jan 1, 1957

By A. Raja, C. C. Harris

Apparatus for maintaining constant — but adjustable — pulp level and rate of froth removal are described. The results of preliminary experiments into the effect of scraping speed on the rate of solid and liquid recovery with a semi-batch system are presented. Glass spheres restricted to a narrow size range is the solid under investigation. Graphical methods for estimating the mass of recoverable material and the zero error are given. The semi-batch procedure1 is extensively used in laboratory flotation testing, though the method is subject to variability of moderate severity. Raffinot2 concluded from a statistical study of the difference between replicate tests, that the ptincipal source of errot was the test itself and not sampling or chemical analysis. These differences can be ascribed principally to changes in pulp volume and reagent concentration, and uncontrolled rate and depth of scraping. Semi-batch testing has been criticized1 on these grounds as a means of investigating flotation kinetics. This paper discusses and describes modifications to laboratory flotation equipment which reduce the number of manual operations and lead to improved control. Kinetic studies were the primary reason for developing the apparatus described. It should, however be a useful aid in normal flotation testing. Some preliminary results of experiments are presented.

Jan 1, 1967

By E. O. Lilge, H. Siebert

A design of a multiple-bomb leaching unit particularly suited for the study of heterogeneous reactions, i.e. sol id-liquid-gas interfaces at high temperatures and pressures is presented. The component parts and overall design are described and illustrated in detail. The system has been tested by a limited number of experiments and found to work satisfactorily. Heterogeneous reactions at solid-liquid-gas interfaces, at high temperatures and pressures, are studied in either autoclaves1'4 or bombs5'9. Autoclaves are usually fairly large vessels which have a stirring arrangement incorporated in the design. Mechanical design limits the use of these vessels to relatively low temperatures and pressures. They are particularly well suited to rate or kinetic studies. Bombs can be designed to be operated at high temperatures and pressures, and are smaller vessels; because of this, stirring arrangements are not easily incorporated. In this paper a multiple-bomb system is described, that has been designed to incorporate the desirable features of both the autoclave and the bomb. The described unit has flexibility for an over all study of leaching. Most of the component units in this assemblage are standard equipment, designed and produced by well known manufacturers. No claim is made to the design of this equipment, and although described in some detail, this is done merely for clarity in the elucidation of the system presented. The general layout of the multiple-bomb assemblage is shown in Fig. 1A and 1B. The basic units in this system are: 1) 6 stainless steel 100 ml bombs (Fig. 4)

Jan 1, 1964

By K. D. Hester, A. W. Fletcher

A nickel-copper sulphide concentrate was treated in a pilot plant at Warren Spring Laboratory during 1961, by a hydrometallurgical roast-leach-solvent extraction process devised to cleanly separate the metal values and produce acid sulphate liquors containing the metals. It is shown that 86 pct of the nickel and 95 pct of the copper could be leached from the calcine, after a sulphatizing roast on finely ground flotation concentrate. Iron was removed from the leach liquor by limestone neutralization with a small loss of values. Copper and nickel were separated by solvent extraction with naphthenic acid in kerosene after partial neutralization of the iron-free liquors with ammonium hydroxide. Hydrogen sulphide and chlorine were used to remove zinc (and residual copper) and cobalt impurities respectively. The recovery of pure copper and pure nickel, by electrowinning, from the acidic solvent extract strip liquors finally produced, appears technically feasible. An economic analysis of production costs shows that small, geographically isolated, nickel-copper sulphide deposits cannot usually be worked profitably by established processes. The requirements for profitable operation on a comparatively small scale could possibly be met by a flotation-roast-leach process. Two difficulties, obtaining satisfactory extraction of nickel from a sulphide concentrate and separating the copper and nickel in solution, have prevented the previous use of this method. A solution to the first problem, dissolution of the nickel, was described in a recent paper by Thornhill.1 It was shown in this paper that copper and nickel in a flotation concentrate could be oxidized to water soluble sulphates by roasting in a fluidized bed with added salt cake. Workers at the Warren Spring Laboratory have shown that the separation of copper and nickel can be accomplished by solvent extraction using a relatively inexpensive carboxylic acid, naphthenic acid. Moreover, the mineral acid required to strip values from the loaded solvent could be produced, and the metals recovered, by electrowinning; thus the latter section of the process was regenerative. The removal of iron from the leach liquor and the elimination of impurities such as zinc and cobalt before nickel electrowinning would be necessary to complete the flowsheet. The process under investigation could therefore be summarized (Fig. 1) as follows: 1) Flotation to produce a bulk sulphide concentrate. 2) Fluidized bed roasting to sulphate the nickel and copper minerals. 3) Leaching of roaster calcine to extract soluble nickel and copper. 4) Precipitation of iron from the separated leach liquor by air oxidation after the adjustment of pH and temperature. 5) Recovery of copper from the iron-free Liquor by pH adjustment and liquid-liquid extraction. 6) Purification of the copper raffinate by removing zinc and residual copper as insoluble sulphides and cobalt as cobaltic hydroxide. 7) Recovery of nickel from the purified liquor by pH adjustment and liquid-liquid extraction. Laboratory and pilot plant studies detailed below, were carried out at the Warren Spring Laboratory, to test the feasibility of each one of the unit processes and to obtain preliminary plant design data. FLOTATION The ore was an altered basic rock containing concentrations of magmatic sulphides.

Jan 1, 1964

By R. S. Silo

A new process for leaching oxidized copper ore (CuO) is presented. Its principle advantage is that it requires low cost raw materials. For large operations the only materials used are sodium chloride (NaCl) and calcium carbonate (CaCO3). In those operations of medium size, sulfur, which is abundant in the North of Chile, is used. However the process may also be applied to small copper plants provided low cost sulfuric acid is available as a substitute for sulfur. That is, it may be applied to those small capacity plants where large additional installations for the regeneration of the leaching solution are not needed. The method is comprised of six stages, namely: Crushing, Leaching, Washing of the Solution, Precipitation, Regeneration of the Leaching Solution, and Fusion. A flow diagram for this process in a large or medium-sized plant is given. LEACHING This process requires hydrochloric acid as the leaching solution for treating copper ores. This is easily produced from sulfuric acid and sodium chloride as follows: A small excess of NaCl is advisable to avoid the presence of free sulfuric acid. The experiments reported here were performed with 36 grams of HC1 per liter of solution to obtain a free acidity equivalent to 50 gpl of H2SO4 (the usual leaching solution concentration). Hydrochloric acid leaching may be done by either of the usual methods; i.e. percolation or agitation. The method selected depends on the characteristics of the ore. No matter which method is chosen, low pressure air can be used either as an air lift for circulation of the solution, or for agitation of the pulp with "Pachuca" tanks. In either case, there are no problems with respect to oxidation. Leaching by agitation produces good recovery; but at times, the problem of high consumption of leaching solution or the overproduction of grinding slimes which interfere with contact between phases negates this advantage. The percolation method was used in this study. Percolation took place in four 15-liter containers, 11 1/2 in. diam. by 12 in. height, having hemispheric bottoms. Each container was fitted with a wooden bottom having 1/4 in- holes. The air lift was a 3/4 in. plastic tube 10 in. high. Air at 6 psi was supplied from a rotating laboratory compressor. 10 kg of ore were charged to the container and counter-current leaching was used. The leaching solutions were fed through the center pipe in order to use the ascending solutions to reject the air in the charge. The solution circulated through the air lift in order to facilitate the movement according to the increase in density produced by the reaction between the phases present. Specific observations made in this report cannot be generalized because the leaching characteristics are dependent on the nature of the ore used, the method of leaching, and the production of primary or secondary slimes while crushing or leaching.

Jan 1, 1967

By F. W. Bloecher

DETERMINATION of the surface area of finely divided minerals is of interest to mineral engineers engaged in flotation, comminution, and de-watering studies. In the industrial minerals field, many materials are classified as to fineness according to their specific surface (surface area per unit weight). A method of surface area determination has been tested and used in the Richards Mineral Engineering Laboratories at M.I.T. It involves low temperature krypton adsorption measurements using the technique described by Beebe.' During the past fifteen years a number of new surface measurement techniques have been developed. Those that are broadly applicable to materials dealt with by mineral engineers include the permeability method in which a gas or liquid is passed through the sample, and the low temperature gas adsorption methods first described by Brunauer, Emmett, and Teller."" Efforts to make surface determinations from size distribution curves have long been attempted"."." but because of the uncertainty of sub-sieve size distribution and inaccuracies in screen analyses, the method is at best only a rough approximation. The most widely used gas adsorption method utilizes nitrogen gas." Nitrogen adsorption, however, is not particularly suited as a tool for most mineral engineers because the method is not applicable for surface determinations on coarse materials, that is, materials coarser than approximately 150 to 200-mesh. Other gases have been used in mineral engineering studies, particularly ethane."' lo The use of ethane gas, however, involves .a technique that is too sensitive for most mineral engineering work. The permeability method of surface area determination has the disadvantage of not being sensitive enough to detect the surface represented by minute cracks, the so-called internal surface of a particle. The low temperature krypton adsorption method described by Beebe1 utilizes apparatus and techniques that are essentially the same as those used in the ethane adsorption method."1° The surface area is calculated by the B.E.T. method."-' The krypton adsorption technique is particularly suited to the needs of the mineral engineer because: (1) The method can be used for making surface area measurements of rather coarse materials (35 to 48-mesh), as well as extremely fine materials, such as clays or colloidal slimes with specific surface that might be as high as 20 to 30 mb er g. (2) The use of krypton gas offers the advantage of low saturation pressures (2-3 mm) at the conveniently obtained liquid nitrogen temperature. Therefore the krypton vacuum system need not be designed to measure or withstand internal gas, pressures above one atmosphere as is the case with the nitrogen gas method. (3) The krypton technique offers the safety feature of employing liquid nitrogen, as contrasted to the ethane technique in which liquid oxygen is required. Furthermore, ethane vapor pressure at liquid oxygen temperatures is low (about 10 microns), and a high sensitivity McLeod gage is required for pressure readings. (4) The measurement technique with krypton gas is much simpler and faster, and the apparatus is less elaborate than that required with either nitrogen or ethane gases. Apparatus A krypton surface measurement apparatus like that used at M.I.T. is shown in Fig. 1. It is constructed of pyrex glass. A vacuum is maintained by two mercury diffusion pumps in series backed by a mechanical vacuum pump."' The vacuum thermocouple gage is used for checking the vacuum within the system. This type of gage is quite sensitive down to a pressure of 1 micron of mercury," but may be used to indicate pressures much lower than that

Jan 1, 1952

By F. W. Bloecher

S. Mortsell and J. Svenssofi (Royal Institute of Technology, Stockholm, Sweden)—Bloecher states that the apparatus described by him should be a suitable instrument in the mineral dressing laboratories for determining the specific surface of such granular products that are generally investigated. We want to express a somewhat different opinion, as we doubt that the gas adsorption method of surface measurement really is the most suitable method in mineral dressing laboratories. It is well known that the surface area, as measured by this method, does not coincide with the surface area calculated from the size, shape, and number of particles, i.e. the superficial surface of the particles. It can be seen easily from Mr. Bloecher's own determination on ilmenite-leucoxene concentrate that the surface area measured according to this method may be several hundred times larger than the superficial surface. It is supposed that the surface of cracks, fissures, and pores within the particles also is included in the measured surface. However, this is an assumption which scarcely can be proved and certainly has not been proved. We believe that the mineral engineer could better use a method giving the superficial surface of the particles, as in most cases this surface only is of importance to him. Such is certainly the case when calculating the resistance of the fluid flow through granu- lar materials and the capillary forces of such materials, problems which are of great importance in connection with dewatering, filtration, and pelletizing'" etc. The same may also be the case when studying flotation problems, partly since the quantities of the introduced reagents usually are so small that they can only cover the most accessible surface of the particles, and partly since the molecules of at least the collecting reagents are so large that they cannot enter the smallest cracks and pores. As to the surface, which is of consequence in the application of Rittinger's law of crushing, one is inclined to believe, from theoretical reasons and from the work by Gross and Zimmerley, that the total surface here is the most important one. However, it seems as if in that case the superficial surface was as important as the total surface. Other reasons making the gas adsorption method less suitable for use in the mineral dressing laboratories are that the granular materials there very often are too coarse to be measured by this method, that the experimental technique is rather difficult, and that it takes a long time to measure the specific surface of a sample. Besides, the validity of the method must still be considered questionable. It is thus well known that with different gases one usually gets different values of the specific surface of the same sample, which values, even with such an ideal material as metal foils, can differ as much as about 50 pct.'" Still more serious

Jan 1, 1952

By Fred C. Bond, Jen-Tung Wang

Comminution energy is principally energy of deformation before breakage, which appears as heat An empirical equation is presented which covers the entire comminution range. The new strain-energy theory considers comminution from the known principles of mechanics and the reduction ratio. Energy requirements according to the different theories the romnnred. THE present status of the theory of comminution is extremely unsatisfactory. The amount of various ores and rock products crushed and ground annually approaches the staggering sum of perhaps one half billion tons. Yet the basic concepts underlying an operation of such magnitude are unknown, and actual knowledge of what takes place in comminution is almost entirely empirical. The responsibility for this situation cannot be charged to apathy or lack of appreciation of the importance of the problem. Many attempts have been made to evolve a workable hypothesis, but none has been completely successful. General Considerations In order to break rock, it must be subjected to a stress which strains the rock beyond its critical breaking point. The stress imparts energy to the rock, most of which is released in the form of heat when the stress and resulting strain are removed. If the strain induced exceeds the critical strain, the energy is released by breaking; if the induced strain does not reach the critical point, the energy is released with removal of the stress as energy of resilience. Rock is a brittle material and it is assumed that it breaks approximately at its yield point, so that no permanent deformation results from strains below the critical. When rock is broken the total energy input is accounted for by the heat liberated, and by the surface energy of the new surface produced. A small and probably negligible amount is released as noise. Rock is commonly broken under compression and the applied stress is ordinarily compressive. However, for breakage to occur, it is only necessary that the induced strain exceed the critical value, and this strain may represent the resultant of compressive, shearing, and tensile forces. The stress-strain diagram of rocks under compression, and the modulus of elasticity as determined therefrom, should be fundamental considerations in the development of any theories of rock breakage. Crushing in jaw or gyratory crushers results primarily from a squeezing action, and reduction in a hammer mill is the result of impact. The action in rod and ball mills is a combination of impacting, squeezing, and wearing away by attrition, or rubbing. In ordinary crushing and grinding, the forces are applied at protruding points and are not distributed evenly throughout the rock. This is one of the features of comminution which theoretical considerations have not covered adequately. Another feature is the effect of impact velocities, which may greatly influence the total energy required for breakage. Impact velocities may vary from 1 or 2 fps in crushers to 10 or 20 fps for ball mills, and as high as 100 or more for hammer mills. However, according to the findings of geophysicists, the velocity of sound and of compression waves in stone is many times greater; the primary longitudinal compression waves travel at perhaps 15,000 fps, and the secondary transverse waves, which may reach the surface and cause cracks to form thereon, travel at perhaps 5000 fps. When a crack tip forms, the total surrounding stresses are concentrated in this tip, which rapidly extends throughout the rock particle.1 It would seem that the energy required to deform the rock beyond its critical strain, resulting in the formation of a crack tip, represents practically all of the energy required. Most of the primary crack tips presumably form on the surface. A simple method of designating feed and product size is necessary for the evaluation of crushing and grinding results. Taggart's suggestion2 that the 80 pet passing size be used has been found very practical. In this paper, the square opening screen size which 80 pct of the feed passes is designated as the feed size F, and the size which 80 pct of the product passes, or the product size, is designated as P. The reduction ratio at the 80 pet passing size, or F/P is designated as n. The feed and prod-

Jan 1, 1951

By Fred C. Bond, Jen-Tung Wang

Comminution energy is principally energy of deformation before breakage, which appears as heat An empirical equation is presented which covers the entire comminution range. The new strain-energy theory considers comminution from the known principles of mechanics and the reduction ratio. Energy requirements according to the different theories the romnnred. THE present status of the theory of comminution is extremely unsatisfactory. The amount of various ores and rock products crushed and ground annually approaches the staggering sum of perhaps one half billion tons. Yet the basic concepts underlying an operation of such magnitude are unknown, and actual knowledge of what takes place in comminution is almost entirely empirical. The responsibility for this situation cannot be charged to apathy or lack of appreciation of the importance of the problem. Many attempts have been made to evolve a workable hypothesis, but none has been completely successful. General Considerations In order to break rock, it must be subjected to a stress which strains the rock beyond its critical breaking point. The stress imparts energy to the rock, most of which is released in the form of heat when the stress and resulting strain are removed. If the strain induced exceeds the critical strain, the energy is released by breaking; if the induced strain does not reach the critical point, the energy is released with removal of the stress as energy of resilience. Rock is a brittle material and it is assumed that it breaks approximately at its yield point, so that no permanent deformation results from strains below the critical. When rock is broken the total energy input is accounted for by the heat liberated, and by the surface energy of the new surface produced. A small and probably negligible amount is released as noise. Rock is commonly broken under compression and the applied stress is ordinarily compressive. However, for breakage to occur, it is only necessary that the induced strain exceed the critical value, and this strain may represent the resultant of compressive, shearing, and tensile forces. The stress-strain diagram of rocks under compression, and the modulus of elasticity as determined therefrom, should be fundamental considerations in the development of any theories of rock breakage. Crushing in jaw or gyratory crushers results primarily from a squeezing action, and reduction in a hammer mill is the result of impact. The action in rod and ball mills is a combination of impacting, squeezing, and wearing away by attrition, or rubbing. In ordinary crushing and grinding, the forces are applied at protruding points and are not distributed evenly throughout the rock. This is one of the features of comminution which theoretical considerations have not covered adequately. Another feature is the effect of impact velocities, which may greatly influence the total energy required for breakage. Impact velocities may vary from 1 or 2 fps in crushers to 10 or 20 fps for ball mills, and as high as 100 or more for hammer mills. However, according to the findings of geophysicists, the velocity of sound and of compression waves in stone is many times greater; the primary longitudinal compression waves travel at perhaps 15,000 fps, and the secondary transverse waves, which may reach the surface and cause cracks to form thereon, travel at perhaps 5000 fps. When a crack tip forms, the total surrounding stresses are concentrated in this tip, which rapidly extends throughout the rock particle.1 It would seem that the energy required to deform the rock beyond its critical strain, resulting in the formation of a crack tip, represents practically all of the energy required. Most of the primary crack tips presumably form on the surface. A simple method of designating feed and product size is necessary for the evaluation of crushing and grinding results. Taggart's suggestion2 that the 80 pet passing size be used has been found very practical. In this paper, the square opening screen size which 80 pct of the feed passes is designated as the feed size F, and the size which 80 pct of the product passes, or the product size, is designated as P. The reduction ratio at the 80 pet passing size, or F/P is designated as n. The feed and prod-

Jan 1, 1951

By D. R. Walker, M. C. Shaw

The laws of Kick and Rittinger are explained as functions of particle size with metal cutting theory. Comminution is shown to be basically the same process as metal grinding. The machine shop type of grinding operation is used to study mineral crushing. Evidence indicates that plastic flow occurs in comminution. THE laws of comminution of Kick and Rittinger have been debated for many years. Certain data obtained from ball mill and drop tests are found to be in approximate agreement with Rittinger's law while other data would seem to support Kick's law. In all these tests the energy required to produce a wide variety of particle sizes has been studied. Surface area has also been measured with considerable difficulty, at first because it was thought that the energy associated with crushing was that required to create new surface, later because of precedent and because a more fundamental variable was unknown. Tests made with the machine shop type of grinding process show that normally brittle materials that are usually crushed can behave like the more ductile metals. Brittleness is then a relative prop- erty largely dependent on specimen size and stress state. The machine grinding operation offers a convenient means for studying the comminution of materials in which the important size variable retains its identity. The energy required to grind a certain volume of material is shown to be strongly dependent on size. Kick's law is found to hold very well for particles below 1 micron in size, while Rittinger's law holds approximately in the comminution of larger particles. While a physical origin of Kick's law is established in terms of the theoretical strength of materials having a perfect lattice structure, there is found to be no physical basis for Rittinger's law. Because of its industrial importance, comminution has commanded considerable technical attention and has been the subject of continuous study for nearly a century. A number of empirical rules have been proposed to make it possible for grinding energies to be predicted. Of these so-called laws of comminution those bearing the names of Kick and Rittinger have been most widely applied and debated.

Jan 1, 1955

By Hans Allenius, R. T. Hukki

This paper describes in quantitative terms the effect of sharpness of classification on the performance of the closed grinding circuit. The analysis is based on a large number of laboratory experiments designed to simulate the two most common industrial closed grinding systems. The experimental results show quantitatively the degree of improvement achievable by more efficient classification. In an earlier paper1 the senior author has presented a trend showing qualitative analysis of mill and classifier performance in tile closed grinding circuit. According to this analysis, the master key to a major improvement appeared to be effective removal of finished fine material from the classifier sands, or in other words, improved sharpness of classification, leading simultaneously to a substantial reduction of the circulating load. One purpose of this paper is to present the results of a quantitative investigation of the closed grinding circuit. Another is to set forth the essential pertinent variables revealed by the quantitative experiments carried out by the junior author. In the two most common systems of closed-circuit grinding, (1) feed to the circuit is introduced into the grinding unit, normally the ball mill, operating in closed circuit with the classifier; or (2) feed to the grinding circuit is introduced into the primary grinding unit, normally the rod mill, discharging into the classifier in closed circuit with the secondary grinding unit, normally the ball mill. In the following discussion, these two systems are analyzed separately in the indicated order. BALL MILL - CLASSIFIER CIRCUIT The Test Apparatus and Procedure: The test appara- tus included: (1) a F 195 mm x 220 mm laboratory ball mill rotated at a speed 77% of the theoretical critical speed, and a 7-kg batch of F 20 mm-F 50 mm steel balls; (2) a conventional 65-mesh test sieve and a Ro-Tap sieve shaker serving as a classifier; and (3) a Permaran instrument manufactured by Outo-kumpu Co. for surface area determinations by the permeability method. As no continuous closed-circuit experiments could be brought about on a laboratory scale, the process was broken down into alternating grinding and sizing steps in such a way that the new feed plus the returning sands always formed a batch of 1000 gm. For each selected grinding period and for each selected sharpness of classification the basic steps were repeated six times. Steady-state conditions were then reached. Crystalline vein quartz was used as a test material. Feed to the process consisted of -10-mesh fraction of this quartz crushed in rolls. This fraction included 15% of-65-mesh material. Experimental Results: The general flowsheet is shown in Fig. 1. Table I gives the essential data obtained representing steady-state conditions under the indicated set of variables. The table is based on 110 grinding experiments, 440 screen analyses and an equal number of specific surface area determinations. Fig. 2 shows the relationship between the cumulative net energy consumption and the cumulative number of mill rotations as evaluated by separate experiments. Note that this relationship is not linear but is instead represented by a slight curve. The data given in Table I are presented in graphical form as follows: Fig. 3 shows the produced -65-mesh material in grams per minute vs. time of grinding in minutes; the sharpnesses of classification at 65 mesh were 100%, 75% and 50%. It is clearly indicated that the highest-capacity figures call for relatively short grinding times and for the sharpest possible classification. Fig. 4 presents the specific surface area on the final -65-mesh product in square centimeters per gm vs. time of grinding in minutes. In conventional mineral dressing processes, a final product characterized

Jan 1, 1969

By R. L. Wiegel

This article proposes a physical model for an idealized binary mineral system and for the process of liberation by size reduction. Based on this model, equations are derived relating the amount of each component liberated as a function of the ratio of the volumetric abundance of the two mineral components and the ratio of the mineral grain size to particle size. A definite relationship is shown to exist between the mineral concentration within a locked particle and the frequency of occurrence of such a particle. These relationships are used to obtain theoretical expressions for the concentration-recovery diagram. Physical mineral beneficiation processes are based on breaking a mineral aggregate to liberate the dissimilar mineral grains and then making use of their physical properties to separate the mixture into its components. The effectiveness of the process is therefore dependent on how well the minerals are liberated and how efficiently they are separated. Although a substantial amount of work is being done to improve our understanding of mineral separation processes, the study of mineral liberation itself has been almost completely neglected. The purpose of this theoretical study is to shed some light on the liberation phenomenon by: 1) proposing a physical model for an ideal binary mineral system, 2) treating mathematically the fracture of this system into liberated and locked particles, and 3) deriving an expression for the liberation characteristics of this system. The results of this study are useful in understanding the effect and importance of various parameters in liberation, and provide a basis for comparison with real mineral systems. 'RANDOM' MODEL It is recognized that liberation can be caused by detachment which results from fractures occurring at the mineral grain boundaries, or by size reduction which restricts the occurrence of dissimilar mineral locking to a portion of the resulting particles. The detachment effect is dependent on the relative strengths of the mineral grains and the bonds between them, and must be treated empirically for each mineral system. The size reduction effect, however, can be treated analytically if certain assumptions are made concerning the shape and geometrical arrangement of the mineral grains.

Jan 1, 1968

By O. B. Buchlen, J. W. Smith

The Coal Research Bureau of the School of Mines at West Virginia University, using an experimental flotation cell designated an airlift-cyclone was able to obtain a clean coal product containing 7.64% ash with 94% yield and 97% coal recovery. This favorable performance was obtained with the experimental flotation cell operating as a simulated three-stage unit on slurry taken from the fine coal circuit of a coal preparation plant. This experimental device, consisting of a sheet metal cyclone-like unit mounted on a U-shaped uplift pipe, uses a combined flotation and cyclone action to beneficiate the minus 14 mesh partially cleaned feed product. In addition to providing comparable analytical results, the airlift-cyclone possesses other attractive features among them being a low capital expenditure, utilization of moderate plant floor space, efficient operation on high density feed slurry, and absence of moving parts. The primary shortcoming of the experimental cell is its limited capacity. The Coal Research Bureau presently has under construction a larger unit which, it is hoped, will provide the capacity and quality to establish the airlift-cyclone as a commercially feasible unit. Froth flotation of fine coal is a practice which has only recently gained wide acceptance in this country. Various explanations can be put forth for this delayed acceptance of a very selective and efficient system of coal preparation. Among these reasons would be the advent of continuous mining machines resulting in the increased production of coal fines, the change in market patterns from domestic and rail consumers who did not want fines to a predominantly utility market which normally consumes fines, and also the imposition of legal restrictions in regard to stream pollution. However, the major detriment is probably the high cost involved both in installation and operation of the flo- tation unit and auxiliary systems. These facts assume greater emphasis when considering that froth flotation installations normally process a low quality feed product. A recent estimate' of installation costs including dryers, filters, and other auxiliary equipment for a flotation system was $5000 to $7000 per ton of capacity while the operating costs, exclusive of auxiliary equipment, were estimated at 10 to 306 per ton of feed. The Coal Research Bureau of the School of Mines at West Virginia University is currently developing a simplified froth flotation cell, designated an airlift-cyclone, which may provide considerable savings in capital and operating costs without sacrificing product quality or recovery. This experimental cell consists of three primary components: 1) a vertically mounted U-shaped pipe; 2) an air injector device; and 3) an integrally mounted cyclone-like unit (Fig. 1). A feed slurry is introduced at the top of one leg of the U-pipe while compressed air is injected near the base of the other leg. The air serves both to aerate the pulp and to cause it to flow upward into the base of the cyclone unit where the floated clean coal is separated from the reject material and unfloated coal which remains in slurry. The Coal Research Bureau's experimental airlift-cyclone is somewhat similar in principle to a flotation device developed by Russian engineers in the late 1950's. In tests upon a two-stage pilot-size device, the Russians obtained very favorable cleaning efficiencies.' However, later experience with production models demonstrated that rated capacities and acceptable product quality could not always be maintained.3 Because of these limitations, Russian engineers subsequently recommended that conventional, mechanical cells be used when cleaning difficult to float slurries. Engineers at the Coal Research Bureau felt that such a device utilizing the combined actions of a cyclone and a froth flotation machine offered numerous attractive features and merited investigation. Accordingly, a small capacity experimental airlift-cyclone was designed and, with the permission of the Christopher Coal Company Div. of Consolidation Coal Co., installed in Christopher's Humphrey preparation plant near Morgantown, West Virginia.

Jan 1, 1964