Search Documents

By E. F. Poncelet

Forty years ago A. A. Griffith developed a theory explaining why brittle materials displayed such low tensile strengths.' He based his views on two points. First, he found himself compelled to assume that all brittle materials are replete with flaws, cracks, and other defects that act, although quite invisible, as large stress raisers. Second, he applied the "theorem of minimum potential energy," which says that the total potential energy of a system must pass from the unbroken to the broken condition by a process involving a continuous decrease in potential energy. By this means he satisfactorily accounted for the noted low strength of such solids and also for the wide spread obtained in experimental measurement of these strengths. So successful has the theory been that it is favored by some to this day. Unfortunately this theory is of limited use beyond the explanation of these two noted phenomena and it is keenly felt that a better theoretical insight into the physics of the fracturing process is needed as the volume of experimental evidence accumulates. The author proposes in the following to build on the fundamentally sound concepts of Griffith and, with the help of increased theoretical knowledge over that available to Griffith, develop a mechanism for frac-ture which will provide far greater understanding of the experimental evidence accumulated to date than is possible from the original Griffith idea. THE GRlFFlTH THEORY Very little progress indeed can be made without accepting the first postulate of Griffith which supposes all brittle solids to be full of microcracks. It would be difficult indeed to find a better mechanism for the small strength of such brittle materials, in conjunction with the fact that the energy that must be expended for comminution is by no means small. The postulate of the existence of the microcracks permits the breakup of the various bonds a few at a time by concentrating the stress at the tip of the progressing crack, while the total energy expended is the same as if they all had been ruptured simultaneously. The only flaw in the argument is that no reasonable explanation has been proposed to account for the genesis of such cracks. Indeed their very presence is in violation of the Griffith second postulate, the potential energy theorem. This theorem is straightforward for isothermal processes, and, in spite of Griffith, there is some doubt that treating the problem isothermally is legitimate. The surface energy of bodies is a free energy, not a potential energy as stated by Griffith, and the production of new surface free energies is not necessarily an isothermal process. There is ample evidence to the contrary. Generally speaking, if heating a body increases its surface area, then, by virtue of Le Chatelier's principle, any increase of that area by other means will tend to lower its surface temperature. Lord Kelvin calculated the actual cooling that resulted in drawing out a film of liquid.2 R. A. Houston calculated the surface cooling that resulted in stretching a metal wire.3 These calculations were made by applying the Carnot cycle to the process and evaluating the thermodynamics thereof. IRREVERSIBILITY OF THE FRACTURING PROCESS While Griffith was very careful not to say so, the impression gained from studying his papers is that he considered the fracturing process as reversible, that is, a succession of quasi-equilibrium states. There is ample evidence that it is not. The indication that the new surfaces produced by the propagation of a crack are cooler than the original body points to an irreversible heat flow from the interior to the new surfaces to equalize the temperatures. If the process be reversible, any crack accidentally formed should immediately close up as, in the absence of any strain energy, the potential energy would thereby be lowered. The fact that they do not, constitutes a paradox. Such paradoxes are nothing new where certain phenomena that propagate from minuscule nuclei are assumed to be reversible. Such is, for instance, the condensation of a pure saturated vapor that is suddenly chilled by adiabatic expansion. At the beginning the tiny droplets that are formed should be only a few angstroms in size, but the vapor pressure at such droplets is so high that they should evaporate at once. A similar situation arises if a saturated pure solution becomes super-saturated upon cooling; the first tiny crystal nuclei should dissolve as fast as

Jan 1, 1964

By Hobart M. Kraner

THE mineralogy of blast furnace sinter is of interest because its mineral content is one of the important factors contributing to its character. There are so many other factors affecting the properties of the sinter, however, that it is well to mention them here. The proportion and character of the raw materials, that is, raw ores, concentrates, returns, and fuel, as well as the mixing and the water content, all have a marked effect on the physical properties of the product and the degree to which sintering action can be carried on. The process of sintering is a relatively fast operation. In as much as appreciable time is required to carry on processes of fusion in such masses of low thermal conductivity, large lumps of hematite ore frequently remain unfused and partly unchanged in state of oxidation in the sintering process. The kind, the grain size, and the amount of fuel used affect both the completeness of the fluxing reaction and the prevailing atmosphere. The rate of reduction in laboratory tests is not only dependent upon the state of oxidation of the sinter but also upon the sizing and porosity. Atmosphere and temperature affect the state of oxidation of the iron oxide, and the atmosphere alone may determine the ferrous minerals that finally develop. The rate and extent of cooling, the type of coolant, the subsequent handling, and screening all have serious effects upon the type of sinter that eventually enters blast furnace bins. The degree to which actual fusion or fluxing takes place in the sintering operation has a marked effect upon density. A sinter which has been extensively fused by high content of fuel in the batch will no doubt have a higher weight on the bulk basis than one which had a lower fuel content. As high temperatures are required to do this job, the iron oxide under these conditions will be largely magnetite. Sintering at low temperatures to produce larger proportions of hematite means a decrease in the amount of liquid formed and a much more sensitive bonding process. In this case the liquid must be distributed more uniformly and thereby used more efficiently than would be the case where higher temperatures were permitted to prevail more or less indiscriminately. Where coarse ore particles are used in a sinter mix it is not expected that any particles coarser than 1/4-in. can be fused and incorporated in the system to such an extent that the gangue contained within these lumps will have been converted or fused by the sintering process. It is for this reason that coarse ore, returns, or both, in a sinter usually result in a sinter which breaks easily and at the same time may contain some of the original minerals of the lump, such as quartz and hematite. In examination of sinters at Bethlehem Steel Co. minerals such as quartz and corundum have been found, none of which are considered normal associ- ates of wustite or magnetite. Some degree of heterogeneity or lack of equilibrium is not unusual in the sintering process. The differences in specific gravity between hematite and magnetite might be ample reason for poor strength in a not very well sintered mass containing coarse particles of. ore or returns. The shrinkage taking place in a lump of hematite in its conversion to magnetite by temperature and/or atmosphere is appreciable. Sintering of ores as it is carried out is crude chemistry, for the grain size is relatively coarse, the application of heat is certainly not uniform, and the time factor is inadequate for other than partial completion of reactions. Coarse lumps of coke or coal cause local heating around these centers, and fuel which is too fine may result in such slow burning that sufficiently high temperatures are not always obtained. High temperatures are essential to the work required. The Swedish practice of sintering is established on the basis of producing an easily reducible product high in hematite. This is achieved through uniformity of grain size in the sinter mix and close control of the temperature through careful regulation of fuel and sintering rates. This produces a sinter which is very tough in character and which has a high degree of porosity. Although the hematite content is not produced upon cooling by drawing air through the mass, there would be greater possibility of accomplishing this reaction with this type of sinter than is the case in American practice. In the latter, the temperatures are so high that temperature alone converts most of the mass to magnetite. The grains are so coarse in the final product that together with the fluxed condition it would be difficult to reoxidize them to hematite upon cooling. An examination of the iron-oxygen diagram' shows that hematite does not exist above 2651°F. It also shows that there is no liquid in the pure magnetite-hematite system until 2881°F is reached. On the other hand, in the system magnetite-wustite liquids exist at considerably lower temperatures than this. It will be seen, therefore, considering only the iron oxides, that the bonding action obtained in America in sinters comes about through considerable temperature and/or reducing conditions that produce compositions containing even less oxygen than is contained in magnetite or than results from the fusion of silicates. The bonding obtained from the iron oxides is encouraged by the reducing conditions that prevail in the vicinity of the fuel particles in a mass of this sort, where temperatures are above 2600°F. As magnetite and wustite are opaque, they do not lend themselves to petrographic study by transmitted polarized light. The silicates found in sinter and the glass that has not crystallized transmit light and can be studied by these methods in which indices of refraction and other optical properties of anisotropic crystals lead to their definite identification. The index of refraction is the only property that can be measured in glass under the microscope, and this is a clue to its probable approximate composition.

Jan 1, 1954

By R. M. Hays

Prior to use of this model siphon finisher, the only means of evaluating metallurgical performance of the siphon finisher was by pilot plant studies. These are costly and require large quantities of material. A model siphon finisher and a test procedure which permits the evaluation of siphon finisher metallurgical performance has been developed. Metallurgical results between the model siphon finisher and pilot plant or commercial units show fairly good correlation. The upgrading of magnetic taconite concentrates by hydraulic concentration has been practiced for several years. In the 1940's, Braund1 used a multistage upflow classifier to upgrade magnetized magnetic concentrates. In present taconite plants, the SiphonSizer, marketed by Dorr-Oliver, Inc., has been particularly suitable for upgrading magnetic concentrates. When the hydraulic SiphonSizer is used to upgrade the concentrates in the finishing portion of the overall flowscheme, the unit will be called a siphon finisher to distinguish this application from classification. Prior to this work the only means of evaluating the metallurgical performance of the siphon finisher was by pilot plant studies which are costly and require large quantities of material. Therefore, it was desirable to develop a model siphon finisher and a test procedure which would simulate siphon finisher performance and require only small samples of material. This model would permit the evaluation of small samples such as drill core samples and be useful in evaluation of commercial siphon finisher design and performance. THE SIPHON FINISHER The siphon finisher, as shown in Fig. 1, is a tank equipped with a system of water jets which distribute the hydraulic water uniformly across the bottom of the vessel with an energy release for agitation in the teeter bed. The feed to the siphon finisher is intre duced through a feed well in the center of the unit. The silica and middling particles overflow a peripheral weir into the overflow launder. The magnetite fraction is discharged by a siphon or a modulated discharge valve. The siphon or the discharge valve is usually operated automatically by a float assembly which is responsive to the depth of the teeter bed. Various interface sensing devices have also been

Jan 1, 1968

By E. J. Roberts

The theory is developed that the tons ground through a given mesh per day in a wet ball mill is proportional to the percent plus that mesh in contact with the balls and the net power applied to the balls at this point. A grindability test is described. DURING the course of a study of the fundamentals of classification in 1937, the need for a more basic understanding of the action of a ball mill became acute. Unless one knows how classification affects grinding, one cannot hope to effectively improve on classification. The methods of evaluating grinding efficiency that depend on surface developed were studied but soon discarded for two reasons: 1. There was no apparent method which could be generally used to give a reliable figure for the actual new surface developed as a result of grinding. Subsequent papers have not changed this conclusion. 2. The practical evaluation of grinding in the main ore dressing applications was in terms of the percentage retained on a screen which passes 90 to 99 pct of the material and not in terms of surface area. The Probability Theory With the background of our experience in the field of closed-circuit grinding, together with the papers of Lennox,1 Gow,2 Gaudin,8 Fahrenwald,4 Coghill, and others, the approach of the theoretical physicist was then tried. The thought was somewhat as follows: When one grinds in a ball mill, a given expenditure of power leads either to a certain number of point to point blows per hp-hr or to a certain distance of line contact per hp-hr, depending on whether the action of the balls is considered to be cascading or rolling. It is also assumed that the balls actually come together on each blow or during the roll. Then a volume of slurry will be covered per minute which is some function of the size of the particle being considered (see fig. 1). All particles coarser than this size will be reduced through this size. This volume of slurry contains a certain weight of ore, depending on the percent solids and the density of the solids. If we fix the percent solids and the density of the solids and let w be this certain weight of ore in the volume covered, then, in mathematical terms, what we have just postulated is, w —— 8 hp (a) dt If W is the total weight of ore present in the mill, then we can write. W w/8 hp (b) W dt and if C is the cumulative percent plus the size chosen at the start of the time interval dt, w w c/dt W 8 hp x c (c) wc But wc/100 is the weight plus the size chosen which at 100 wc the close of time dt is finer than that size, and W is the decrease in the percent plus of the whole mass of ore or —dC. Then, —W dC/dt 8 hp x C. (d) In other words, the mesh tons ground through a given size per unit of time is proportional to the hp and the percent plus the mesh. A crude analogy would be to picture a 1-ft-wide steam roller going down the road at 1 ft per sec. If we place one egg on the road per square foot, one egg will be smashed per second. If we place a dozen eggs per square foot, a dozen eggs will be crushed per second. Similarly, if all the particles in w are plus the mesh, i.e., C=100, we should have a maximum rate of reduction. If only 10 pct of them are plus the mesh (C=10), we would have only one tenth the maximum rate; if only 1 pct are plus the mesh, the balls have a hard time finding anything to work on. This is where the term "probability theory" comes from. The chances of the balls crushing a particle through a given mesh depends directly on the concentration of particles coarser than this mesh in the general pulp in the mill. Giving W the units of tons and dividing equation (d) through by W, we obtain -dC hp ----- = k---— C [1] dt ton where k is a constant for any one size of particle, density of solid and moisture content of pulp. Eq 1 is the rate equation for a first order reaction and says that the rate of decrease of the percent plus a given mesh with time is directly proportional to the hp per ton applied to the body of ore and to the percent plus the mesh in the ore mass as a whole. Since it is a differential equation, it only

Jan 1, 1951

By E. J. Roberts

The theory is developed that the tons ground through a given mesh per day in a wet ball mill is proportional to the percent plus that mesh in contact with the balls and the net power applied to the balls at this point. A grindability test is described. DURING the course of a study of the fundamentals of classification in 1937, the need for a more basic understanding of the action of a ball mill became acute. Unless one knows how classification affects grinding, one cannot hope to effectively improve on classification. The methods of evaluating grinding efficiency that depend on surface developed were studied but soon discarded for two reasons: 1. There was no apparent method which could be generally used to give a reliable figure for the actual new surface developed as a result of grinding. Subsequent papers have not changed this conclusion. 2. The practical evaluation of grinding in the main ore dressing applications was in terms of the percentage retained on a screen which passes 90 to 99 pct of the material and not in terms of surface area. The Probability Theory With the background of our experience in the field of closed-circuit grinding, together with the papers of Lennox,1 Gow,2 Gaudin,8 Fahrenwald,4 Coghill, and others, the approach of the theoretical physicist was then tried. The thought was somewhat as follows: When one grinds in a ball mill, a given expenditure of power leads either to a certain number of point to point blows per hp-hr or to a certain distance of line contact per hp-hr, depending on whether the action of the balls is considered to be cascading or rolling. It is also assumed that the balls actually come together on each blow or during the roll. Then a volume of slurry will be covered per minute which is some function of the size of the particle being considered (see fig. 1). All particles coarser than this size will be reduced through this size. This volume of slurry contains a certain weight of ore, depending on the percent solids and the density of the solids. If we fix the percent solids and the density of the solids and let w be this certain weight of ore in the volume covered, then, in mathematical terms, what we have just postulated is, w —— 8 hp (a) dt If W is the total weight of ore present in the mill, then we can write. W w/8 hp (b) W dt and if C is the cumulative percent plus the size chosen at the start of the time interval dt, w w c/dt W 8 hp x c (c) wc But wc/100 is the weight plus the size chosen which at 100 wc the close of time dt is finer than that size, and W is the decrease in the percent plus of the whole mass of ore or —dC. Then, —W dC/dt 8 hp x C. (d) In other words, the mesh tons ground through a given size per unit of time is proportional to the hp and the percent plus the mesh. A crude analogy would be to picture a 1-ft-wide steam roller going down the road at 1 ft per sec. If we place one egg on the road per square foot, one egg will be smashed per second. If we place a dozen eggs per square foot, a dozen eggs will be crushed per second. Similarly, if all the particles in w are plus the mesh, i.e., C=100, we should have a maximum rate of reduction. If only 10 pct of them are plus the mesh (C=10), we would have only one tenth the maximum rate; if only 1 pct are plus the mesh, the balls have a hard time finding anything to work on. This is where the term "probability theory" comes from. The chances of the balls crushing a particle through a given mesh depends directly on the concentration of particles coarser than this mesh in the general pulp in the mill. Giving W the units of tons and dividing equation (d) through by W, we obtain -dC hp ----- = k---— C [1] dt ton where k is a constant for any one size of particle, density of solid and moisture content of pulp. Eq 1 is the rate equation for a first order reaction and says that the rate of decrease of the percent plus a given mesh with time is directly proportional to the hp per ton applied to the body of ore and to the percent plus the mesh in the ore mass as a whole. Since it is a differential equation, it only

Jan 1, 1951

By P. Somasundaran

Flotation of minerals has usually been discussed in terms of solid-liquid interfacial phenomena. This paper discusses the relative importance of phenomena such as collector adsorption at other interfaces formed between the bubble, liquid and solid. Adsorption of collector ions of various chain lengths at liquid-gas and solid-gas interfaces has been obtained. The data have been analyzed under conditions corresponding to those of flotation to show the significant role of collector adsorbed on the bubble surface in determining the bubble-mineral attachment required for flotation, and consequently to suggest consideration of this role in the development of better flotation conditions. Vacuum flotation of quartz with alkyl ammonium acetate reported in the foregoing paper1 showed that the collector chain length has an effect on flotation even at concentrations below those necessary for hemi-micelle association of the hydrocarbon chains at a solid-liquid interface. This chain length effect might be explained by the following arguments: Hydrocarbon chains find it energetically favorable to be in a medium of low dielectric constant. Considering the possibility of an iceberg structure at the solid-liquid interface, such a structure would produce a region of lower dielectric constant at the solid-liquid interface than in the liquid phase, because the dielectric constant of ice is 2 to 3,2 while that of water is 80. Depending on chain length, this difference will certainly cause even individual ions to adsorb in higher quantities at the solid-liquid interface. Another mechanism to consider is the possible formation of dimers, trimers, etc and chain length would influence this formation. But, above all, the chain length effect on flotation at concentrations of low adsorption at the solid-liquid interface could be due to the significant but often-neglected role of the collector adsorption at the bub- ble surface. Collector ions or molecules are adsorbed both at the solid-liquid interface and the liquid-gas interface. Below the concentration for hemi-micelle association at the Stern plane adjacent to the surface, the bulk of the collector ions adsorbed at the solid-liquid interface are in the diffuse part of the double layer. If such systems, where there is a gas bubble coming in contact with the solid surface, are to achieve some degree of electroneutrality, those collector ions would have to migrate from the diffuse part of the double layer to the region directly adjacent to the surface during the induction period when the bubble is making contact with the solid. The time necessary for this migration would contribute to the induction period required for creation of the solid-gas interface. It seems reasonable that the induction period could be reduced sufficiently for flotation to occur if these collector ions were carried to the surface by the bubble. In an attempt to ascertain whether or not the bubble could possibly have sufficient collector ions at its surface to meet the requirement mentioned above, the adsorption density of the collector ions at the liquid-air interface was determined. For this purpose, the surface tension of alkyl ammonium acetate solutions was determined as a function of concentration. Adsorption densities of the collector at the liquid-gas interface were calculated using the Gibbs adsorption equation: where y is the interfacial tension and ri and pi are the adsorption density and the chemical potential, respectively, of the chemical species, i. Using the convention that the adsorption density of water at the interface is zero, the following relationship is obtained for the liquid-gas interface where lg refers to liquid-gas interface and RA+ refers to the alkyl ammonium ions. For dilute solutions, rf^-wri^&rfwW [3] where C is the concentration of the collector ions in solution. l?:: can now be evaluated using Eq. 3 and surface tension measurements.

Jan 1, 1969

By H. Eklund, R. T. Hukki

This article presents a simple arithmetic derivation for the relationship between sharpness of classification and circulating load, as well as world-wide industrial data which are compatible with the derived equation. It is shown that the sharpness of classification decreases with increasing circulating load. Based on the evidence available a comparison is presented between the performance of the present-day hydraulic classifiers. In a continuously operated closed circuit grinding system the tonnage and the fineness of the components may be indicated as follows: Eq. 8 expresses the relationship between sharpness of classification and circulating load in closed grinding circuits. If CL = 0, E = 100% according to the definition used. This, however, is a purely theoretical case because any apparatus to be called a classifier must produce the conventional two products. Furthermore, if CL = m, E =0%. In order to visualize the meaning of Eq. 8, the effect of factors d (fineness or percentage of under-size of classifier overflow at size x) and b (fineness or percentage of undersize of classifier sands at size x) should be studied. By the most rigid standard, factor d should be given the value of 100%. By so doing the size of classification is defined as that screen size x through which 100% of the classifier

Jan 1, 1965

By L. Weyher, H. L. Lovell

This discussion is restricted to a very specific application of the cyclone - its use as a hydro-cyclone in the cleaning of fine coal. It is hoped that the development of the present data will assist in the further elucidation of existing qualitative models, and also in an enhanced application of the hydrocyclone and provide a base for further research. Discussed are the mechanisms of gravity separation in hydro-cyclones, test procedures, experimental observations, and industrial applications from these studies. Within the general area of unit operations, a considerable effort has been expended in theoretical and empirical research associated with cyclone operations. The motivation involves the industrial requirement for devices and techniques to manipulate small particles at low operating costs, a situation required in coal preparation. There are good reasons why the cyclone helps to satisfy this demand, because it combines operational simplicity (no moving parts) with versatility and high throughput capacity per unit area. The cyclone is one of the most widely applied tools in the process technologies. There are areas for potential cyclone application which have been only meagerly explored or not considered at all. This discussion is restricted to a very specific application of the cyclone - its use as a hydrocyclone in the cleaning of fine coal. It represents an initial presentation of a more comprehensive report. Coal preparation can appropriately claim the hydrocyclone since most of its predominant industrial uses have originated in this area and have spread into other applications, including the broad field of ore dressing, the petroleum industry, chemical processing, nuclear engineering and food technology. There is one operational principle common in all cyclones: A fluid is tangentially introduced into a cylindrical or conical container under pressure. A predominantly irrotational flow field1 is established within the cyclone (Fig. 1). The uniqueness of this flow is indicated by the variation in tangential velocity across the cyclone radius, which reaches a maximum a short distance from the center and decays toward the cyclone wall. In contrast, the tangential velocity in a centrifuge increases uniformly toward the wall. Usually two products are discharged from the cyclone. They differ in that one discharge consists predominantly of that portion of the feed fluid which moves along the wall axially away from the feed inlet, while the other consists predominantly of fluid spiralling along the central regions of the cyclone, in an axial direction opposite to that of the wall current. Fig. 2 indicates these discharge points schematically. The latter product may be termed the vortex-product, since it is discharged with the central vortex-current. In the case of conical cyclones, the former product may be referred to as the apex-product. Although the names "over- and underflow" are widely used, many cyclones are operated from extreme angular positions thus the proposed terms are less ambiguous. The cyclone feed fluid can be laden with solid particles or nonmiscible fluid drops. Such a feed component is discharged from the cyclone, after some residence time, into the one or the other product. Yet, the orifice through which a particle will leave the cyclone is dependent upon a number of factors. These factors, in a statistical sense, determine the path of the particle within the cyclone. Thus, different separation phenomena are possible and different process results attainable by the controllable variation of the particle path. It is then, to attain a fuller understanding of this particle path, to which this study is ultimately directed. It is anticipated that the detailed study of the data being developed will allow further elucidation of existing qualitative models. However, the development of a quantitative description of cyclone operation in terms of a mechanism is not currently feasible. The flow conditions in a cyclone are not fully understood even for a pure fluid, without the added complexity of the inclusion of multiple size-density particles. It is hoped that the development of the present data will also assist in an enhanced application of the hydro-cyclone and provide a base for further research. Some practical applications drawn from the data are suggested. Cyclone operations have been classified according

Jan 1, 1967

By M. C. Fuerstenau, W. F. Cummins

The flotation response of quartz in the presence of calcium chloride and various fatty acids is presented. Flotation is not effected with lauric acid until calcium laurate is precipitated in solution, while flotation is obtained with the 9, 10, and 11-carbon members before precipitation of the calcium carboxylate. The active species responsible for flotation is suggested to be a basic aqueous complex, e.g. Ca(OH) (RCOO) (aq), and a possible mechanism of adsorption is given. Most of the previous work on activation in non-metallic flotation systems has involved the use of high molecular weight collectors, such as oleic acid or alkyl aryl Sulfonate.1-7 In these studies the levels of addition of collector and activator required for flotation were much above the concentrations necessary for precipitation of the metal-collector salt. In fact, Clemmer, Clemmons, Rampacek, Williams, and Stacy1 have stated, "Our experiments on a variety of materials have demonstrated that the metal salts which react with anionic collecting agents, as soaps and alkyl sulfates, to form relatively insoluble compounds may be employed as activating agents provided an optimum quantity is used at a proper pH." On the other hand, Gaudin and chang8 obtained flotation with additions of barium and lauric acid below the level required for barium lautate precipitation.

Jan 1, 1968

By D. A. Elgillani, M. C. Fuerstenau, M. C. Kuhn

The species responsible for flotation when xanthate is added as collector for pyrite is dixanthogen. Measured oxidation potentials of these systems show that xanthate should be oxidized to dixanthogen, and the presence of dixanthogen on the pyrite surface is confirmed by infrared absorption. Zeta potential measurements are presented and related to collector adsorption. In spite of the normal presence of pyrite in most sulfide ore deposits, only a modest amount of study has been devoted to the xanthate-pyrite flotation system in the absence of activators and depressant~.'-~ As a result, little is known about the mechanism of xanthate adsorption on pyrite. From the few studies that have been made, however, a number of significant observations have been forthcoming. For example, the dependence of flotation response on the state of oxidation of the surface was noted in two studies — one conducted by Plante and Sutherland4 and a later one by plaksin.~ In another study, Gaudin and wilkinson3 found that ferric xanthate was not present on a pyrite surface. In a later investigation, however, Gaudin' and his colleagues did extract a small amount of ferric xanthate into benzene when pyrite was ground in an evacuated mill with water, benzene, and xanthate. This quantity was apparently

Jan 1, 1969

By T. W. Healy, P. Somasundaran, D. W. Fuerstenau

The flotation behavior of quartz in the presence of alkyl ammonium acetates as a function of alkyl chain length has been interpreted in terms of hemi-micelle formation at the solid-liquid interface. The van der Waals cohesive free energy that is responsible for hemi-micelle formation has been found from these results to be 1.0 kT per CH2 group. This is in excellent agreement with literature values obtained from research on the properties of micelles in bulk systems. Collectors of the type CH3(CH2)n-2CH2-P, where P is a polar group and n is the number of carbon atoms in the straight alkyl chain, will induce flotation of an appropriate mineral at lower concentrations as n increases. This reduction in collector concentration with increasing n has been reported for such systems as xanthates on sulfides1,2 and amines on quartz.' The effect of chain length of alkyl surfactants on such solution properties as conductivity,' surface tension,' and solubility6 and such interfacial properties of solids as contact angle7 and electrokinetic potential8 have received considerable attention, but only limited quantitative descriptions of the effects have been given. The electrokinetic studies of alkyl amine salts on quartz indicated that the solution concentration of collector at which the marked change in electrokinetic potential of quartz occurs decreases systematically as the length of the alkyl chain increases. The aim of the present work was to obtain a quantitative description in terms of current theories of flotation of the effect of the hydrocarbon chain of alkyl ammonium acetates on the flotation behavior of quartz. BASIC PRINCIPLES The marked changes in electrokinetic potentials of quartz in dodecylammonium acetate (DAA) solutions were postulated to result from the association of adsorbed collector ions into two-dimensional aggregates, called hemi-micelles.9 Subsequently, the rapid increase in flotation rate of quartz was shown to coincide with hemi-micelle formation." We would like to discuss briefly the concept of hemi-micelles in terms of recent interpretations of micelles in bulk solution. Micelle hypothesis: In dilute solutions, alkyl ammonium and related salts behave as ordinary strong electrolytes, but at a certain concentration there is a marked change in physical properties of the solutions, e.g., in equivalent conductance, transport number, freezing point lowering and viscosity. To account for these phenomena, McBainl1 introduced the concept of micelles, which are aggregates of long-chain ions. It is believed that the ionic heads of the constituent ions of the micelle are in contact with water, whereas the nonpolar groups turn away from it and are in contact with each other. Work must be done to bring these charged polar groups together, but energy is gained (i.e., so called van der Waals cohesive energy) when hydrocarbon chains are expelled from the water and allowed to associate. For a given polar group, the tendency to form micelles will therefore strongly depend on the hydrocarbon chain length. Theoretical treatments of micelle formation by Shinoda12 and Phillips13 and others lead to the following expression for the concentration at which micelles form (the critical micelle concentration or cmc) in aqueous solutions of long- chain electrolytes

Jan 1, 1964

By C. C. Martin, M. C. Fuerstenau, R. B. Bhappu

Experiments revealed that quartz could not be floated in conductivity water at any pH with a long-chained sulfonate as collector. Various cations, Fe+++, Al+++, Pb++, Mn++, Mg++, Ca++, are shown to function as activators when the pH is such that the cation hydrolyzes. As the solubility product of the various cation-sulfonates was exceeded at the concentrations involved, precipitated cation-hydroxy-sulfonates, e.g. Fe (RSO3)2OH must be functioning as the collector in these systems. A number of interesting and important phenomena were revealed during a study of the response of beryl to sulfonate flotation.' Perhaps the most important observation is the effect of various cations on flotation response. Experiments showed that in the vicinity of pH 3.0, about three ppm Fe+++ increased recovery of leached beryl from about 60 pct to 100 pct, whereas about four ppm Ca+ + reduced the recovery from 60 pct to 2 pct. With the exception of ferric iron, all of the other cations investigated reduced flotation recoveries drastically at this pH. As postulated in the paper Sulfonate Flotation of Beryl,' even with low concentrations of polyvalent cations and sulfonate (on the order of one ppm), cation-sulfonates are precipitated immediately in solution. That is, blueish-white clouds were noted to form after given additions of salts to known solutions of sulfonate. Furthermore, it was also shown that one-hundred-fold more ferric iron than necessary to form the precipitated cloud had to be added to effect complete flotation. In other words, some form of solid ferric sulfonate was found to function as the collector in these systems. The form of the compound was suggested to be Fe(RCO3)2OH and that bonding to the surface occurs through the hydrogen of the hy-droxyl. As the form of this compound was shown to be dependent on the extent of hydrolysis of ferric iron, it is to be expected that ferric iron will be unique in some pH region. Further, if the presence of hydroxyl in the neutral precipitated compound is of primary importance, then other cations should function similarly but at different values of pH, since they will hydrolyze at different concentrations of hydroxyl ion. To determine whether the premise of hydrolysis is correct, the study was extended to quartz systems in the presence of various cations at various values of pH. EXPERIMENTAL MATERIALS AND METHOD Sodium alkyl aryl sulfonate was chosen as the collector for the experimental work. The reagent, sup plied as a courtesy sample by the Shell Chemical Co., has the following physical properties: Physical form Solid — Finely ground Sulfonate content, pct wt 95 to 97 Molecular Weight 450 to 470 Number of carbon atoms in hydrocarbon chain 25 to 30 Melting Point, OF 250 to 260 Solubility Soluble in water with gel formation at concentrations higher than 25 pct by weight sulfonate This particular reagent was chosen because of its high active sulfonate content, long-chain length, and solid form. With the exception of the frother and sulfonate, all other chemicals were of reagent grade quality. Conductivity water was used in the experimental work. This water, made by passing distilled water through an ion exchange column, had an average measured conductivity of one micromho. Experiments were conducted at room temperature in a small glass flotation cell with the following procedure: 1) A redetermined amount of water and salt solution (e.g. CaC12 . 2H2O) were combined and the pH adjusted to a given value. 2) A given amount of sulfonate was added so that final solution volume was 130 cc. 3) One drop of Dow 250 frother was added. 4) Five g of quartz were added and the system conditioned for five minutes. 5) The pH of the system was measured (termed flotation pH).

Jan 1, 1963

By V. M. Karve, K. K. Majundar, K. V. Viswanathan, J. Y. Somnay

The effect of calcium, magnesium, iron (both ferrous and ferric) and aluminum ions, which are commonly encountered in a typical beryl ore, was studied in the flotation of pure beryl, soda-feldspar and quartz. The vacuumatic flotation technique was employed. With sodium oleate as collector and in the absence of any activator, beryl floated in a pH range of 3 to 7.5, whereas feldspar and quartz did not float at any pH up to 11.5. The pH range of flotation increased in the presence of the ions studied. With calcium and magnesium ions beryl floated from 3 to 11.5 pH and beyond, soda-feldspar floated beyond pH 6 and quartz floated beyond pH 8. Ferrous ion activation was found to be similar to that of calcium and magnesium. Activation by ferric and aluminium ions was found to be complex and the lower and upper critical pH for all the three minerals was around 2 and 10 respectively. These studies indicated the possibility of separation of beryl from feldspar and quartz even in the presence of calcium, magnesium and ferrous ions between pH 4 and 6. Flotation tests on a mixed feed of pure minerals in a 10 g cell revealed that beryl can be selectively floated from feldspar and quartz if ferric ion is reduced to ferrous state or if it is complexed. Beryl occurs mostly in pegmatites, and hence is associated with feldspar, quartz and micas and small amounts of other minerals such as apatite and tourmaline. The separation of beryl from these minerals is difficult because all the silicates accompanying beryl have more or less the same physical properties. Specific gravities of beryl, feldspar and quartz are 2.70, 2.56 and 2.66 respectively. Electrostatic separation has been suggested but no work has been reported. ' The adsorption of sodium tri-decylate tagged with Cl4 on beryl, feldspar and quartz reveal similarity in surface properties. Much work has been reported on the flotation of beryl from ores, either directly or indirectly as a by-product, but little is known about the fundamental aspects of beryl flotation. Kennedy and O'Meara3 laid emphasis on prior cleaning of the mineral surfaces with HF. Mica is removed first by flotation of beryl with oleic acid, around neutral pH. Runke4 introduced calcium hypochlorite conditioning in a final separation stage for activating beryl in a mixed beryl-feldspar concentrate, and after washing to remove the hypochlorite, floated beryl with petroleum sulphonate. The Snedden and Gibbs5 procedure is somewhat similar to that of Kennedy and O'Meara. Emulsified oleic acid is used as collector. Recently Fuerstenau and Bhappu6 studied the flotation of beryl, feldspar and quartz with petroleum sulfonate in the presence of activators and stressed the importance of iron in the flotation of beryl. From the studies conducted in this laboratory, it was found that feldspar and quartz as such do not float with sodium oleate, but in practice selective flotation of beryl from feldspar and quartz in an ore is found to be impossible with sodium oleate as collector. A glance at the chemical analysis of typical beryl ore indicates the presence of several ions like Ca ++, Mg++, Al + + + and Fe+++ in abundance and Ti++++ and Mn++ in traces. Hence, in an attempt to explain the behaviour of feldspar in the beryl flotation, the effect of Ca++, Mg++, Al+++ and Fe+++, which are known as gangue mineral activators7'8 has been investigated. Materials and Methods: Lumps of beryl ore (hand picked) were boiled with 10% sodium hydroxide and washed with distilled water. They were further boiled many times with 10% hydrochloric acid till no positive test for iron was obtained with ammonium thio cyanate. This was followed by thorough flushing with double distilled water. The lumps were crushed in a porcelain mortar and pestle under water. The minus 65 + 100 mesh fraction was used for testing and was always stored under distilled water. Pure feldspar and quartz were similarly prepared and the minus 65 + 100 mesh fractions collected. Inorganic ions tried as activators were ca++, Mg++ , Fe++, Fe ++ and A1 +++ . Calcium nitrate, magnesium chloride, ferrous ammonium sulfate, ferric ammonium sulfate and aluminum nitrate of G.R.E. Merck grade were used. B.D.H. technical grade sodium oleate was used as a collector. The vacuumatic flotation technique developed by Schuhmann and Prakash was used for studying the effect of pH on flotability. 7 The indications given by this work were confirmed by using 10 g miniature cell.'

Jan 1, 1965

By D. A. Elgillani, S. Atak, D. A. Rice, M. C. Fuerstenau, R. B. Bhappu

Quartz and feldspar cannot be floated with sulfonate at any pH; spodumene floats over a narrow acid pH range, while beryl responds moderately over a broad pH range. After wet-grinding in a steel mill, beryl, quartz, and spodumene float well with sulfonate below about pH 7, whereas the improvement in the response of feldspar is not so marked. A mechanism by which iron can be adsorbed on these minerals is presented. Also, the responses of leached, natural, and wet-ground beryl to amine, sulfonate, and oleate flotation are shown and related to the measured zero-points-of-charge of these materials. Earlier work with leached beryl showed that good flotation could be obtained with alkyl aryl sulfonate over a rather wide pH range using a Fagergren flotation cell.' When a similar response was observed with leached quartz, it was decided that unintentional activation was being obtained from the metallic components of the Fagergren cell. To obviate this difficulty, a microflotation cell was designed, and an experimental technique was devised. These have been described elsewhere. Experiments conducted with the small cell showed that leached quartz could not be floated at any pH with any sulfonate addition,3 which is in agreement with the observations of Kraeber and Boppel.4 Similarly, it was also found that leached beryl responded to sulfonate flotation only over a narrow pH range rather than the broad range reported earlier.1 This early work,1 however, revealed the important effect that wet-grinding in a steel mill has on the flotation response of certain silicates. That is, it was found that quartz and especially beryl floated well over an unusually wide pH range after wet-grinding in a steel mill. Microcline, however, floated poorly below pH 4, even though wet-ground under the same conditions. The work of Eigeles6 on adsorption of oleic acid on leached quartz and iron-contaminated quartz at constant pH is in agreement with these flotation data. Other research has shown that ferric iron, added as a salt to the system, functions as an activator in the narrow pH range in which Fe +++ iron hydrolyzes to its hydroxy complexes.3,5 These phenomena indicate that iron functions differently in flotation systems depending on its method of introduction. The object of this paper is to determine the mechanism by which iron is adsorbed on certain minerals, the mechanism of collector adsorption after iron abstraction, and the role that Fe++ and Fe+++ assume in the selective separation of these minerals. EXPERIMENTAL MATERIALS AND METHODS Sodium alkyl aryl sulfonate, mol wt 450,7 pure potassium oleate, and pure dodecylamine were used as collectors. All other chemicals were reagent grade in quality, i.e., n-amyl alcohol as frother; HC1, H2SO4, and KOH for pH adjustment; and ferric chloride as activator. Conductivity water, made by passing distilled water through an ion exchange column, was used in the experimental work. All minerals used in the investigation were hand-picked specimens. Sample Preparation: Each of the minerals was crushed through 8 mesh, and the product was divided into two groups, one to be ground dry and the other wet. Dry grinding was accomplished with an alumina mortar and pestle. The product was dry-screened to 48 x 150 mesh, cleaned magnetically, deslimed in conductivity water, and dried. Preparation of the samples by wet-grinding involved grinding a 200-g charge of the mineral (-8 mesh) at 60% solids with natural water in a mild steel rod mill for four minutes. This charge was then wet-screened immediately with natural water to 48 x 150 mesh, dried, and cleaned magnetically. Some experiments were also conducted with leached beryl and quartz. These products were prepared by leaching the sized sample (48 x 150 mesh) with concentrated HC1 with a percolation technique until no iron could be detected in the leach liquor. Following this step, the sample was rinsed with conductivity

Jan 1, 1967

By M. C. Fuerstenau, J. D. Miller

The response of calcite to flotation with saturated fatty acids and alkyl sulfonates of various chain lengths is presented. The amount of collector re-quired for flotation is shown to decrease systemati-cally with increasing carbon content from 8 to 12-carbon atoms per molecule. This systematic flotation response is correlated with the solubilities of the calcium-collector salts, which were established with a nephelometer. The 14-carbon collectors deviate from this systematic behavior, and no flotation is possible with the 16-carbon homologs. As determined by infrared analysis, the mechanism of collector adsorption involves a specific chemical reaction be-tween the collector and the surface. A reaction of the form CaCO3(s)+ 2 RCOO"=*=Ca(RCOO)2(s) + C03= is suggested. The pH of the system is also shown to be a most important parameter as it controls the carbonate, calcium, and collector ion concentrations in solution and thus controls flotation response. The importance of hydrocarbon chain length of collectors was recognized early, and various studies have been made on this aspect of flotation. Wilkinson, ' for example, noted that as the chain length of alkyl xanthates is increased, the amount of collector required for flotation of sphalerite is decreased. The same effect has been shown in the flotation of galena.2 Similar results were obtained when malachite3 and calcite4 were floated with various fatty acids. DeBruyn5 has shown that a similar phenomenon occurs when quartz is floated with amines at constant pH. Recently, Fuerstenau, Healy, and Somasundaran6 correlated this phenomenon with the van der Waals cohesive free energy of association of the hydrocarbon chains. It seems unlikely, however, that chain association could be involved in the sulfide and carbonate systems with the collector additions employed, especially with the short-chain xanthates. Rather, it would seem that the decrease in collector concentration with increase in chain length noted for flotation is related to the solubility of the metal-collector salt. The purpose of this investigation is to verify this premise and also quantify this phenomenon if possible. Calcite was selected for study with both alkyl sulfonates and saturated fatty acids as collectors. EXPERIMENTAL MATERIALS AND METHODS The collectors used in this investigation ranged from 8 through 14 carbon atoms per molecule. The fatty acids had a reported purity of greater than 99%. The sodium alkyl sulfonates were provided by the Marathon Oil Cot, Littleton, Colorado, and had the

Jan 1, 1968

By L. D. Keller

The application of hydraulic concentration to large scale operations has been effectively accomplished by the use of the SiphonSizer. Operation has been simple, automatic and essentially trouble free. The use of the primary desliming SiphonSizer on magnetic taconites has shown an improvement in grade of concentrate and an increase in recovery over conventional hydroseparators. Magnetic concentrates have been further deslimed and upgraded in SiphonSizers by floating a coarse middling product away from the heavier concentrate. The application of the Siphon-sizer to closed circuit grinding has met with only partial success to date. Hydraulic concentration of minerals has been practiced for a good many years. Until recently, however, the practice has been limited to equipment using a multiplicity of small pockets and relatively low tonnages and flows. The adaptation of the SiphonSizer to the concentration and classification of magnetite has changed this concept. Some fifty commercial units varying in size from a 16-ft diam circular unit to a 25x100-ft rectangular unit are currently in operation on magnetic taconites. Additional units up to 38 ft diam are under construction. Depending upon the application in the flowsheet, upgrading varies from 0.75% to 14% Fe in a single stage. To those not familiar with taconite processing, the importance of the struggle to remove economically as much silica as possible may not be fully appreciated. Perhaps some figures pertaining to transportation costs will underscore this important process. If the silica content of the concentrate from a 10,000,000 ton per year plant could be reduced by I%, a savings in boat freight, at $2.00 per ton, would amount to $200,000 annually! THE SlPHONSlZER The SiphonSizer, as illustrated in Figs. lA, 1B and 2, is a hydraulic classifier in which the hydraulic water is distributed uniformly across the bottom of the vessel by means of a system of headers (1 and 2), jet pipes (3), and nozzles (4). The depth of the teeter bed is automatically maintained by the siphon-float assembly. The feed is introduced through a feed well (5) and separated into two fractions by the effects of rising water and the density of the teetered bed. The magnetite fraction is discharged by the siphon (12) while the fine slime and light middling overflow a peripheral weir (9) to the overflow launder (6). The bed depth is controlled automatically by float valves (7), which are responsive to changes in the height of clear water supported in the superelevation tubes (8) by the density of the teetered bed. On top of the float (7) is a needle valve (10) which permits

Jan 1, 1963

By R. R. Kimpel, L. G. Austin

An equation is derived describing fragment size for single fracture of brittle solids. It contains the equations of earlier workers as special or approximate cases and, in addition, is capable of describing coarse distributions in which a few large particles are produced on fracture. The equation can be fitted well to single fracture experiments where over-breakage is avoided. In 1956 Broadbent and callcottl described a method of analyzing the unit operation of grinding, applicable to homogeneous breakage of brittle materials. In essence, the grinding process was split into two parts: 1) the fractional amount of a given size which is selected for grinding per unit time, 2) the size-weight distribution of the fragments produced by breakage of this certain size (primary breakage distribution function). The theory was formulated using matrix algebra. They attempted an experimental verification of the theory using an assumed primary breakage distribution but the results were not very satisfactory. Austin and Gardner2 showed that this assumed distribution was widely different from experimental values and that it led to the poor agreement of predicted size-weight distributions with experiment found by Broadbent and Callcott. In addition, Austin and Gardner2,3,4 reformulated the original approach in terms of differential equations of grinding and demonstrated that the approach led to a very satisfactory description of the grinding process, providing that the descriptive parameters were measured experimentally. Recent work5 has substantiated these findings and the distribution functions of several materials ground under different conditions in different mills have been determined experimentally. The fraction underweight versus size used by

Jan 1, 1965

By R. T. Hukki, P. Voutilainen

This paper describes a new apparatus for continuous wet fine-screening. Its preferred size range seems to be from 0.1 to 1 mm. The supercritical trommel screen is a short cylindrical trommel of wedge-bar type construction operated at a speed greater than the calculated theoretical critical speed and at a speed lower than the speed at which particles introduced into it will centrifuge. The paper describes results obtained with the prototype supercritical trommel screen in pilot plant scale. The results point to a high capacity and simultaneously to a high sharpness of screening. Finally, an analysis is presented of the forces acting in screening on a supercritical trommel screen. In the era of high speed, high capacity processing of raw materials the conventional slowly rotating trommel screen is often considered a relic from the times passed. A typical trommel screen is the cylindrical trommel rotated about a horizontal or slanting axis at a relatively low speed. Its screening characteristics are well known. Trommel screens of various types of construction, methods of operation, performances and other characteristics have been described in detail by Taggart.1 The theoretical critical speed of a trommel screen is defined by the same well known equation as that applied for grinding mills: where ncritical = the numerical value of the theoretical critical speed in rpm, D 1 = the inside diameter of the trommel in feet, and D2 = the inside diameter of the trommel in meters. ncritical corresponds also to the centrifuging speed provided that the coefficient of friction f between the trommel surface and the outer layer of the charge is = 1.0. In a general case: From Eq. 2 it is seen that in all cases where f < 1.0 the centrifuging speed of the trommel is greater than the theoretical critical speed. The supercritical trommel screen concerns screening operations within that speed range which is between the theoretical critical speed defined by Eq. 1 and the centrifuging speed defined by Eq. 2, under conditions such that the coefficient of friction f<1.0. It is reported by Taggartl that the optimum speed of a conventional cylindrical trommel screen 36 in. in diam was experimentally found to be about 16 rpm. From Eq. 1, the critical speed of this trommel is 44.2 tpm. The indicated optimum speed corresponds to (16/44.2) x 100% = 36.2% of the theoretical critical speed. The optimum speed range based on information available seems to vary from 33% up to 45% of the theoretical critical value. The trommel screen operated at a supercritical speed: operates at a speed greater than the calculated theoretical critical speed; operates at a speed lower than the speed at which the charge introduced into it will centrifuge; operates within the supercritical speed range in such a way that the coarse fraction of the charge must slide in respect to the inside surface of the trommel; the outer layer of the said fraction next to the screen tends to proceed in the same direction as any selected point on the trommel surface, but now at a lower speed, and indeed at a subcritical speed; allows to a certain degree adjustment of the maximum determining particle size x of the fine product simply by a variation of the speed of the trommel within the supercritical speed range. With increasing trommel speed, finer and finer material only will get the opportunity to find its way into the fine product while the screen opening remains constant. In conventional practice, the low speed trommel is generally used for sizing of coarse and medium coarse material, but seldom for fine screening. The characteristic feature of the product passed through the conventional trommel is that the determining size x of the biggest particle is barely smaller than the nominal size of screen opening. The supercritical trommel screen, on the other hand, is best suited for sizing of relatively fine material. Furthermore, the characteristic determining size x of the biggest particle in the fine product can be substantially smaller than the nominal width of the screen opening or slot. In the trommel screen best suited for the applications

Jan 1, 1965

By G. L. Tufford, R. L. Bleifuss

Low-grade manganiferous iron ores of Minnesota&apos;s Cuyuna Range, in general, do not respond to conventional mineral dressing techniques because of their fine-grained texture. Reducing these ores to magnetite with subsequent magnetic separation and flotation have not given satisfactory results because, in many instances, concentrate grade and manganese recovery are low. Metallization of iron and concurrent reduction of higher manganese oxides to MnO, as in the R-N process, followed by recovery of iron by magnetic separation and manganese by leaching, seems to be a technically feasible process. High-temperature x-ray diffraction studies show that solid-state reactions between iron and manganese, with the formation of intermediate iron-manganese oxides, occur during reduction and affect recovery of both iron and manganese from the final product. Solid state reactions also occur between FeO, MnO, and SiO, at temperatures as low as 900°C. The kinetics of these reactions are such that they become an important factor in the treatment of ores by the R-N process. These investigations suggest a temperature and gas composition cycle that would maximize both iron and manganese recovery. During the past ten years, iron ore shipments from the Cuyuna Range of Minnesota have decreased sharp1y. Because of adverse grade, structure, and cost, many Cuyuna ores are no longer competitive with high-grade foreign ores and domestic pellets. The low-grade manganiferous iron ores from the Cuyuna Range, in general, do not respond to conventional mineral dressing techniques because of their fine-grained texture. Reducing these ores to magnetite for subsequent magnetic separation and flotation has not given satisfactory results because concentrate grade and manganese recovery are often low. However, a technically feasible process appears to be metallization of the iron and concurrent reduction of manganese oxides to MnO with recovery of metallic iron by magnetic separation and extraction of manganese from the tailings by leaching. In 1962 the R-N Corp., with a grant from the Area Redevelopment Administration, conducted an amenability study of the metallization of manganiferous iron ore from the Cuyuna Range. The results of this preliminary investigation were sufficient to interest the Economic Development Administration in sponsoring further studies of the process with emphasis on secondary recovery of manganese from the nonmagnetic tailings. Inasmuch as the metallization process has considerable influence on the final form of the manganese - its texture and distribution between the magnetic concentrate and nonmagnetic tailings-the investigation included a study of metallization of the ore as well. Therefore, the investigation conducted at the Mines Experiment Station covered three interrelated phases: (1) laboratory R-N roasting studies and magnetic separation tests, (2) laboratory chemical extraction experiments of the nonmagnetic tailings, and (3) a mineralogical study of the crude ores and their various roast products. High-temperature x-ray diffraction investigation of the Fe-Mn-Si0,-0, system is the main topic of this paper and an extension of the mineralogical work. GENERAL GEOLOGY The Cuyuna Range is known for its complicated geologic structure, complex orebodies, and generally indifferent response to attempts at conventional beneficiation. Several geologists have made intensive studies of the Cuyuna Range, including Leithl (1907), ~darns&apos; (1910), Zapffe3 (1925), Grout and Wolff4 (1955), and schmidt5 (1963), whose study was the most comprehensive of all. The Range is covered with glacial deposits - till, out-wash, and lake sediments -up to 250 ft thick. Bedrock stratigraphic units of the Cuyuna Range consist of three tightly folded Precambrian sedimentary formations. The lower unit is the Mahnomen formation, composed of 2000 or more feet of argillite, slate, siltstone, and quartzite. The middle unit is the Trommald formation, which varies from 45 to 500 ft in thickness and comprises the major iron-bearing formation. The upper unit is the Rabbit Lake formation, consisting of over 2000 it of argillite, slate, and interbedded lenses of lean iron formation. In the central part of the Cuyuna Range, the units have been folded into a series of

Jan 1, 1969

By F. Habashi

Conclusive evidence is given showing that the dissolution of gold in cyanide solution follows mainly the over-all equation A similar equation can also be written for the dissolution of silver. Theoretical derivation of the velocity equation for this reaction has been obtained, which describes quantitatively the experimental facts. The equation is as follows: where [CN-] and [O2] = the concentrations (in moles/ml) of cyanide and dissolved oxygen, respectively. DcN- and Do2 = the diffusion coefficients of cyanide and dissolved oxygen; 1.83 x 10-5 and 2.76 x 10-5 cm2 sec-1, respectively. A = the surface area of the metal in contact with the aqueous phase, in cm S = the thickness of the boundary layer; varies between 2 and 9 x 10-3 cm, depending on the speed and method of agitation. Rate being expressed in g. equiv. sec-1. INTRODUCTION During recent years a number of papers have been published on the kinetics of dissolution of gold and silver in cyanide solution.1,6 The authors agree that the rate of dissolution is diffusion-controlled, but disagree regarding the mechanism of the reaction. Some authors&apos;-3 support the Bodlander equations: The apparently conflicting results, when critically reviewed, are concordant and lead to the conclusion that the proper equation for the dissolution reaction should be only Eq. 1. This conclusion is based on the following facts: 1) For every 2.2 equivalents of metal dissolved one mole O2 was consumed. 2) For every 1 equivalent of metal dissolved, 2 moles of cyanide were consumed.&apos; 3) Hydrogen peroxide is formed during the dissolution of gold or silver, and for every 2.2 equivalents of metal dissolved, one mole H2O2 was produced.1,2 The fact that Kudryk and Kellogg4 did not detect H2O2 during the dissolution of gold should not throw doubt on the many affirmative reports of other investigators. Lund2 has shown that depending on the crystalline nature of the silver surface, (e.g. method of etching the sample) H2O2 may undergo catalytic decomposition heterogeneously according to: Further Kudryk and Kellogg4 carried out their experiments in the presence of 0.5% KC1 to achieve a greater electrolytic conductivity, and Matsudaira7 has shown that H2O2 is catalytically decomposed (homogeneously) in the presence of C1- ion in alkaline solution. 4) Experiments carried out by Boonstra8 and Lund2 showed that the dissolution of gold and silver respectively in KCN + H2O2 in the absence of oxygen was a slow process. Thus the reaction takes place to a minor extent only. Further kinetic studies showed that: 1) The rate of dissolution depends on the surface area of the metal in contact with the liquid phase, thus indicating that the process of dissolution is a heterogeneous process. 2) The rate of dissolution depends on the speed of stirring,5,6 thus indicating that the process is controlled by a physical phenomenon.

Jan 1, 1967