Search Documents

By Richard M. Foose

FIVE miles southwest of Mt. Holly Springs, Cumberland County, Pennsylvania, the Philadelphia Clay Co. has been mining and milling a white clay since 1896; for use in white cement, as a filler in rubber, pigment and paper, in the manufacture of insecticides, and for other minor purposes. Until late in 1942, when the mine was abandoned because of labor shortage, combined underground mining and surface stripping produced approximately 30,000 tons of clay a year, of which 10,000 tons were refined in the mill. GEOLOGY Lower Cambrian Antietam quartzite and the Montalto quartzite, stratigraphically older, trend N.55°E. and make a sharp 1600-ft. anticlinal ridge of the South Mountains. The Tomstown dolomite overlies the Antietam quartzite on the southeast flank of the anticline, which is displaced near its crest by a steeply dipping oblique fault. Erosion of the less resistant Tomstown formation has resulted in a narrow valley at an elevation of 700 ft. Directly on top of the Antietam quartzite and at the base of the Tomstown formation is a zone of sandy white clay, lenticular along the strike of the formations, ranging in thickness from 10 to 300 ft. within a mile. All of the formations dip steeply to the southeast, from 65° to vertical. The clay crops out at an elevation of about 1000 feet. ORIGIN AND CHARACTER The uppermost part of the Antietam formation is sericitic and schistose at many places, and at all these places weathering is in an advanced stage. The clay is the residual product of weathering of this sericitic quartzite or sandy schist. The crude clay has the physical aspect of a sandy kaolin, but there are large areas in the clay formation that are low in free silica, and commonly the 30 ft. adjacent to the Antietam quartzite is notably free of silica. The overlying Tomstown dolomite has been weathered almost completely to a mixed yellow and brown clay, which carries a zone of nodular and chunky limonite and manganese ore, 4 to 12 ft. thick, about l00 ft. from the contact with the white clay. In mining, this zone is an important "marker," indicating where the white clay may be expected in an advancing tunnel. The contact of the white clay formation with the yellow and brown clay of the Tomstown formation is relatively sharp, although the line of contact is irregular and therefore responsible for the lenticular character of the white clay formation. Following is an analysis of the refined clay containing less than one per cent of moisture when dried at 212°F.: Si02, 67.05 per cent; A1203, 22.27; Fe203, 0.40; CaO, 0.00; Ti02, 1.05; MgO, 0.52; Na20, 0.04; K20, 0.88; ignition loss, 7.65; total, 99.86.

Jan 1, 1944

By Frank Riddle

PRODUCTS made from the ores of the sillimanite group, and synthetic substitutes for them, have unique properties, and service tests prove that they are playing, and will continue to play, a major part in improvements in metallurgical processes. Also, they are examples of how comparatively useless, rare, or "museum" minerals have been made available in commercial quantities. Until research developed uses for them, the minerals had been observed only in small, scattered masses, or crystals. Improvements in ceramic processes and compositions have come about very gradually. In the last 10 or 15 years, several outstanding developments have been made. Of greatest interest to the mining and metallurgical engineers are those affecting the composition, necessitating the mining of new minerals, and improvements in ceramic products used in metallurgical processes.

Jan 1, 1932

By D. Rankin, H. J. Stucke, W. K. B. Loftus

Discussion: H. J. Wright (Member): The authors are to be congratulated on presenting such a comprehensive and lucid account of bringing a large diamond mine into efficient production from the grass roots. When one considers the vast amount of planning and hard work that had to be put into the project the authors have done a praiseworthy job in condensing the story, so as to present all the important technical aspects, the logic behind the major decisions and the future thinking on the operations, in a concise and readable form. This was the first experience of De Beers personnel in starting a large diamond mine as an opencast project and nor do they employ a large planning staff, most of the planning being carried out by the executive staff themselves. It is operating most efficiently on a large tonnage and it is neatly and very well laid out. In fact, with its model townships, both for European and Coloured employees, tarred roads, recreation club and its grass golf course, it is like an oasis in the arid climate of the North-Western Cape. The key operation of opencast mining is, of course, the planning of the geometry of the pit. This has been adequately dealt with by the authors. It is of interest to consider some of the consequences arising from complete lack of open pit planning, based on actual operating mines. I refer of course to the present, four producing mines in Kimberley. The Kimberlite pipes were all discovered in a short span of time from the year 1870, onwards. They soon became a hive of activity with diggers industriously working their claims at varying rates. The country rock comprises from the surface downwards, some 90 ft of decomposed dolerite followed by approximately 260 ft of soft Karroo shales, which in turn is underlain by a hard competent Ventersdorp lava, known locally as melaphyre. The average water table was just below the dolerite at a depth of approximately 90 to 100 ft. Only the blue ground was mined leaving the waste rock sides almost vertical, and as the depth increased beyond 100 ft, large falls of sidewall started to take place. The shale was unstable and the falls covered

Jan 3, 1969

By D. Rankin, H. J. Stucke, W. K. B. Loftus

SYNOPSIS Planning for the Finsch opencast mine is described with particular reference to the proposed stages of mining, the method used to determine the limits of surface waste rock stripping and the derivation of the waste rock mining rate. Actual mining practice is described and the possibility of installing a skipway into the open mine at a later date is discussed. In addition, the waste dumping policy is referred to: this includes the cutting of slots through the hill on the west side of the pipe to increase tramming speeds. The crushing, washing and recovery sections of the treatment plant are described together with the various changes being made to the circuit. The most important of these are the installation of X-ray sorters for the final recovery of + 7 mesh diamonds, and the vibrating grease belt for the recovery of - 7 mesh diamonds. INTRODUCTION The Finsch Mine, a subsidiary of De Beers Consolidated Mines, Limited, is situated approximately 90 miles west of Kimberley, and some two miles from the village of Lime Acres, in the Northern Cape. Lime Acres is a company village shared with the Northern Lime Company which operates a limestone quarry and works near the township. The mine is near the southern end of a well mineralized belt producing limestone, asbestos, diamonds, manganese and iron ore, and the whole area has developed rapidly in the last 20 years. Power for mining operations is drawn from the Electricity Supply Commission. The mine is conveniently close to the main Kimberley-Postmasburg railway line. Water is drawn from the Vaal River through a 57 mile State-owned pipeline at present temporarily operated by mine staff. DISCOVERY AND PROSPECTING OPERATIONS The diamondiferous orebody is situated on the farm Brits, which is State-owned ground that has been leased to the Company for the period of mining operations. There are indications of interest in the area by prospectors (Richter, de Bruin and others) over a period of some 30 years and the discovery would possibly have been made years earlier but for a law preventing prospecting for precious stones on State-owned land. Although the pipe formed a clear depression on the hill where it was situated, it was overlain by some 5 to 40 ft of banded ironstone rubble which was washed into the depression from the hillside above the pipe and obscured the deposit. In 1958, Mr Allister Thornton Fincham applied for, and was granted, the right to prospect for base minerals on the farm Brits. Asbestos is known to occur in the area and, initially, was Mr Fincham's primary interest. However, during the prospecting operations, garnets were discovered and it was realised that diamonds might be present. In 1960, when the Precious Stones Amendment Act was passed, a company

By Richard W. Smith

THERE are three distinct varieties of phosphate rock, in Tennessee, known commercially as: (a) the "brown" rock, which is the residual pro- duct of the weathering and natural concentration of certain phosphatic Ordovician limestones; (b) the "blue " rock, which is an unaltered phosphatic stratum of Mississippian or Devonian age; and (c) the "white" rock, which is the result of chemical replacement and deposition. Before 1894, South Carolina and Florida had supplied most of the phosphate of the United States, South Carolina leading until that date and Florida from then until the present time. In December, 1893, the blue phosphate of Tennessee was discovered almost simultaneously on Swan Creek, in Lewis County, by two independent parties-by one as the result of a careful and systematic search for a workable deposit of the long known kidney phosphate, and by the other through mistaking it for a "bloom" of coal. Leases were taken and, with further prospecting disclosing other deposits in the region, the development progressed as rapidly as 'could be expected without railroad transportation

Jan 1, 1924

By R. J. Grissom

PHOSPHATE deposits have been worked in many countries of central and south central Tennessee, but only ht ebrown rock deposits of Maury and Giles Counties will be discussed at any length in this articles, as all of the major opeations are now located there. They are: Mt. Pleasant District-Federal Chemical Co., Hoover and Mason Phosphae Co., International Minerals and Chemical Corp. (Maury and Giles Counties), Virginia-Carolina Chemical Corp. (formerly Charleston Mining Co.), and Victor Chemical Co. Columbia District-Armour Fertilizer Works and Monsanto Chemical Co. In the near future, the well-known, extensive deposits of blue rock in Lewis and Hickman Counties,also the brown rock in Hickman, Willamson, Summer and Davidson Counties, will again come into production. Certain physical peculiarities of the Tenessee deposit have played an important part in the design and use of mining and milling equipment.

Jan 1, 1944

By Emilio Navarro

XML technology can be used as a standard to transfer information from a relational database to any system that relies on such information. There have been many proprietary methods to perform this information transfer, However, none of them was either able to talk to each other or exchange information in a transparent way. This paper describes a system that will allow for a transparent exchange of information not only between a Web browser and a Web Server but also a stand-alone application and the same Web Server. First, the autor summarize the Internet technologies that support the possibilities. Then the autor outline the tasks needed in order to take advantage of these technologies. Finally, it is suggest a few applications that could take advantage of this system.

Aug 25, 2002

By W. H. Moore, E. T. Powell

IN the early days of mining in the Anthracite field, only the thicker and better seams of coal were mined, because of the limited mining and coal-cleaning facilities, therefore many of the thinner and less productive seams were permitted to remain unmined. With improvements in mining methods, the introduction of modem preparation plants, and the increased market demand for small-size coal, the thinner and more laminated seams have now become assets. In many instances these seams overlie the mined-out beds of the thicker and better seams, from which all recoverable coal was removed by the conventional breast-and-pillar method of mining. Some collieries in certain sections of the Anthracite field are now relying on these thinner and laminated seams. For the purpose of illustration, a large area in the Hickory Swamp-Ridge Basin of the western middle coal field has been selected, where as early as 1898 the No. 4, or Little Buck Mountain, seam was mined and pillars removed. The No. 5, or Buck Mountain, seam lying on a comparatively light pitch and with intervening strata of but 55 ft. of rock was not mined until 1935. Farther east, in the same basin the Nos. 8 and 9 seams, which are two splits of the Mammoth seam, have been mined and robbed and the workings have been abandoned since 1896. The overlying No. 9 ¾ seam, or the upper split of the Mammoth, and the No. 9 ¾ or 4-ft. seam remained virgin, with only an interval of 50 ft. of rock separating them, and with 40 to 50 ft. of rock strata separating the No. 9 ½ seam from the completely mined area of the Nos. 8 and 9 seams. These seams lie on a pitch of 45° on the south side of the basin and on 75° on the north side of the basin. Mining has been carried on in the 9 ½ and 9 ¾ seams for 3 years on both dips of the basin, for a distance of 3500 ft. In some sections the overlying strata of the thicker seams previously mined have settled without any apparent breaks in the upper strata, as indications have shown in the top split of the Mammoth; while in other areas the roof and bottom of this top split of the Mammoth have settled unevenly, thereby causing the bottom and roof to break into blocks. In attempting to mine over a large area of the No. 5 or Buck Mountain seam, a similar settlement has been encountered; the roof of the seam has been broken and a considerable amount of timbering has been necessary in order to make the mining of the seam possible. The conventional breast-and-pillar method, using shaker conveyors, has been used in the No. 5 seam, and a slant-breast method in the mining of Nos. 9 ½ and 9 ¾ seams. MINING OF LIGHT-PITCH SEAMS The No. 4 seam was mined and robbed by the conventional breast-and-pillar system. In this area the seam pitched from 5° to 25° on the north dip, averaged 8 ft. in thickness and had a slate bottom and a

Jan 1, 1941

By Robert G. Lundquist

This paper is a brief summary of work done on mining applications of high energy projectiles. Full scale field testing already completed has used cannons to drive a tunnel, drill large diameter holes, do secondary breakage in an open pit mine, and scale loose rock from inaccessible pit walls. Other applications are suggested in driving development openings, particularly raises. The method will be economically feasible only if cheap liquid propellants are developed.

Jan 1, 1977

By W. J. Mcgaughey, R. G. McCreary, S. C. Maxwell, R. P. Young

"Seismic tomography is a process for obtaining images or maps of seismic velocity or other seismic properties of a rock mass. Seismic velocity images reveal variation in elastic moduli which, in tum, are related to several properties required in the geological or geomechanical assessment of a rock mass. Seismic velocity is sensitive to lithology, discontinuities, and in situ stress. Spatial or temporal variation of these properties may be indirectly assessed. Tomographic measurements are sensitive to volumes of ground, rather than determinations at points, or along lines or surfaces, as in conventional geological or geomechanical measurements or mappings.Tomography surveys are complementary to conventional measurements as they have the capability to interrogate a substantially larger volume of ground. They are thus useful in discerning trends or patterns in regions between or surrounding conventional ""point"" measurements of lithology, rock quality, stress, or other parameters of interest. Seismic velocity images give broad indications of trends in velocity; their spatial resolution of ground properties is typically on the order of five to ten per cent of the nominal survey dimension.Research in seismic tomography has been carried out for several years, and the capabilities and limitations of the technique in mining environments are beginning to be understood. This report reviews the present capabilities of seismic tomography surveys in mining, emphasizing rock mechanics applications. Six case studies are used as examples to demonstrate the capabilities of the method in assessing lithological variation, density and orientation of discontinuities, and the effects of stress."

Jan 1, 1994

By J. E. Friant

Until 1956, drill and blast was the only way to excavate rock. In that year, a tunneling machine using disc type cutters economically bored a small Toronto tunnel. Its amazing 105 ft/day set a new world record and set the stage for a new industry. The Disc Cutter Role in Excavation Mechanical excavation of hard rock is by now deeply ensconced in the heavy civil construction industry. All over the world, from the Swiss Alp Melange to Hong Kong Granite, to New York Gneiss, huge Tunneling Boring Machines (TBMs) create transportation, water and sewer tunnels. Powerful machines, boasting as much as 6000 hp, bore through rock, excavating in excess of 1400 tons per hour. The tool that makes this tunneling phenomenon possible is the single blade, rolling disc cutter. These hardened steel discs, from 15 1/2 to 19 inches diameter are arranged on a rotating cutterhead, to cut concentric circles in the rock. As the machine is propelled forward under great pressure, rock below each cutter is crushed. But the efficiency of the cutterhead is derived from the science of cutter spacing (distance between cutter paths). The majority of the rock excavated is not crushed, but flakes off in chips and chunks. No pick, tooth, or drag type cutting tool can duplicate the performance of a disc cutter. The economic use of drag type tools is limited to as low as 5,000 psi UCS rock strength in massive formations. In weakly bonded, foliated rock, drag tools do better, but are still limited to rock generally less than 15,000 psi.

Jan 1, 2002

By I. Dumitrescu

Since 1990, the entire Romanian mining industry has suffered a major restructuring, i.e. technical and economic. The large majority of the remaining active mines are these with a chance for economic comeback. This is also the case for the mines that belong to MINVEST Deva Company; most of the mines are closed, and are waiting to be reclaimed. The authors present the closing procedures of the former copper mining perimeters managed by MINVEST. It is well known that pollutants of concern for the environment must be monitored to obtain reliable information on the quality of ambient conditions and to minimize their impact on the environment. Consequently, the monitoring problems during the closing procedures will be presented.

Jan 1, 2008

By R Valenta, A Littleboy

Geological heterogeneity is one dimension of complexity in mining. Significant effort is put into developing an understanding of this complexity so it can be used in resource estimation, mine planning and economic modelling. However, over the decadal lifespan of a mining venture, many other dimensions add to the complexity of a mining operation. These include: technological evolution, market fluctuations; investor confidence; social norms; local expectations; and ecosystem functionality. As with geology, these factors are all heterogeneous, uncertain, time varying and represented through sparse and incomplete datasets. Recent work (Valenta et al) is beginning to show us how these risks correlate in different global settings. By analysing data relating to known, but as yet undeveloped copper deposits, this work (the complex ore body database) is demonstrating that it is the combination of issues (both price sensitive and non price-sensitive) that determine the viability of a deposit for extraction in the 21st century.CITATION: Littleboy, A, Plint, N and Valenta, R, 2018. Mining as a complex system: do we need a new model?, in Proceedings Complex Orebodies Conference 2018, pp 41–43 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By Boyack DJ

DEFINING AN ECONOMIC TARGETExploration usually begins with the corporate goal of finding a minimum tonnage and grade of a selected mineral. Sometimes this is expressed more simply as a minimum quantity of contained metal without any indication of the desired grade or implied profitability. Such a goal is useful in the selection of exploration areas and the planning of initial drilling programs. However, it should be reviewed as soon as significant mineralisation has been identified. To make rational decisions about exploration expenditure, the potential return from a deposit must be estimated from the outset and re-esti-mated frequently.The potential return will depend on:1. The proportion of mineral which can be economically recovered from the deposit by mining (the mining recovery).2. The quantity of valuable constituent that can be recovered after dilution with waste rock during mining and losses due to incomplete metallurgical recovery.3. Expectations of price and markets.4. Capital and operating costs applying to the selected mining and processing methods, and to transportation and marketing. Increasingly, environmental costs and constraints must also be considered.

Jan 1, 1990

By J. Navoyski, B. Macdonald, W. J. Helfrich, J. L. Bellanca, B. Demich

DISCLAIMER The findings and conclusions in this paper are those of the authors and do not necessarily represent the official position of the National Institute for Occupational Safety and Health, Centers for Disease Control and Prevention. Mention of company names or products does not constitute endorsement by NIOSH. ABSTRACT The pervasiveness of high-fidelity video games raises expectations of quality, detail, and lighting in virtual reality (VR) applications. However, high-quality models of mining equipment and environments are often not readily available, and developers may not be familiar with the latest techniques, such as physically based rendering (PBR). Because a consistent aesthetic is critical for maintaining immersion and controlling visual stimuli in research as well as in training, researchers at the National Institute for Occupational Safety and Health (NIOSH) created an asset development workflow. This paper details this workflow, including precision modeling and PBR techniques as well as a rigorous review process. It also describes lessons learned in the creation of photorealistic VR assets. BACKGROUND Virtual reality (VR) describes the simulated experience generated by an assemblage of hardware and software that are used to immerse the user. Over many years VR developers targeted the development of virtual environments (VE) toward various purposes: entertainment, the treatment of phobias [1], rehabilitation [2], and training [3]. A large part of the VE development includes digital assets, where digital assets refer to the non-programmed elements including 3D models, audio, and user interface. Because vision provides nearly 10Mbps of data [4] and accounts for the majority of all sensory input combined [5], a focused effort on asset appearance in VEs is warranted. Furthermore, research has shown that higher-resolution imagery increases search performance and training transfer, necessitating high-fidelity assets [6, 7]. In addition to being visually appealing, it is important that the assets and environment are also dimensionally accurate and consistent in order to elicit appropriate responses from the end users as they interact with and among these items [8, 9]. Researchers at the National Institute for Occupational Safety and Health (NIOSH) have developed VEs and digital assets under several research projects over the course of the last two decades [10, 11, 12, 13]. This work has provided researchers with a strong knowledge base for digital asset development. However, the assets themselves have had limited reuse value. Due to the extended timeframes and limited scope of these projects, the previously developed assets are not consistent in visual quality and dimensional accuracy. Moving forward, researchers wanted to minimize future development time and use of resources as well as adopt new asset development tools and game engine technology. Therefore, the aim of this paper is to document a new asset development workflow including geometry, materials, UV layout, and shader implementation combined with review steps in order to produce high-fidelity simulation assets that are accurate with consistent characteristics, using repeatable methodologies that are well documented.

Jan 1, 2019

By Bruce Bryant

Silver ore was discovered at Aspen in 1879, but the district did not reach full production until 1888 after lawsuits were settled and railroads furnished less expensive transportation to the outside world. The boom years were 1888-92; production declined thereafter. From the middle 1920's until 1950, the Midnight mine in the Richmond Hill district furnished most of the output in the Aspen quadrangle. Since 1950, little mining has been done at Aspen. The metals produced were silver, lead and zinc. Native silver dissolved from the sulfide ores was redeposited by waters circulating as deep as 300 m below the land surface, resulting in great secondary enrichment of many of the deposits. Over 100 million ounces of silver were produced in the Aspen quadrangle. Low-grade lead-zinc deposits remain between the old workings locally, and data available suggest that primary ore below levels mined is also of low grade. The ore occurs in the Mississippian Leadville Limestone and the lower part of the Pennsylvanian Belden Formation in sites that were made favorable for deposition by a number of stratigraphic and structural factors.

Jan 1, 1982

By Henderson, Robert

A GOOD idea of the magnitude of the underground operations at Climax can be gained from the following figures. A little more than 43,000,000 tons has been drawn from the mine and of this amount, 40,500,000 tons has been drawn in the past ten years and 12,000,000 tons was drawn in two of the war years. The maximum daily average output over a period of one month was slightly more than 20,000 tons but during this period, production on certain days was 24,000 tons, and 9000 tons was produced in a single eight-hour shift. This production came chiefly from 260 draw points although all of them were never in operation at one time. The haulage system for these draw points is made up of 7.5 miles of 36-in.-gauge track, and 131,000 ft. of subsidiary drifts and 44,000 ft. of raises have been driven to develop the necessary broken ore reserves for this high production. Power consumption is often considered an index of operating efficiency. In 1943, the year of maximum production, the mine power consumption was 19,223,000 kw.-hr. or 3 kw.-hr. per ton; in 1945 it was 3.5 kw.-hr. per ton. To handle this amount of power, there are four transformer stations and one switch station in the mine. Mr. Garrabrant, the chief electrician, describes the electrical installation in this issue.

Jan 1, 1946

By Claude Bourgoin

"The Copra massive sulphide deposit occurs as a continuous slab of ore dipping at approximately 40 degrees within a sericite schist formation. The orebody has been delineated over a distance of more than 5,000 feet down dip. This paper is mainly concerned with the mining procedure, and particular reference will be made to the use of steel mill holes and hydraulic roof supports. The gravel backfill line, which is operated both by gravity and hydraulically, is described. The paper mentions some of the operational problems, discusses the feasibility of longwall mining and presents the information obtained from stope testing."

Jan 1, 1966

"Many underground mines are achieving extended life and optimizing existing facilities by mining at greater depths. The challenges to do this require a sound engineering approach to mine design and mine services, as well as ingenuity in safety design. The social consequence is full utilization of existing infrastructure.Accessing ores at depths of 2000 m to 3000 m requires exceptional hoisting design. May’s theme issue includes a paper that examines a case study of one such hoisting plant, with emphasis on the hoist rope selection at Agnico-Eagle’s Penna shaft. The paper also describes the process whereby consultation with provincial safety authorities resulted in a revised safety factor suited to the hoist. Another paper examines the challenges of ventilating mechanized mines to 3000 m, including air cooling and dilution of diesel exhaust emissions. Vent system designs are discussed, using sound engineering design, and proven technology that minimizes emissions to achieve cost efficiencies. The paper suggests design based on process and ventilation simulators to obtain realistic economic data at the design stage. Increased ground pressures present unique challenges for production and safety. While this is not confined to deep mining, one paper examines rock pressures and seismic events at the Brunswick mine, for which experience may be applied at depth. It describes seismic monitoring as a predictive tool in a real mine situation, and how it is used to improve overall recoveries and maintain worker safety."

Jan 1, 2004

By Lloyd F, Arnold D. A, Hagan T. O

This paper investigates the problems that are encountered in mining at extreme depths. It looks into the rock mechanic aspects, especially the high stress levels that will occur, and the hazard of rockbursts. Furthermore, environmental problems are discussed, with refrigeration and reduction of neat loads being major methods of maintaining ,sorkable conditions. The paper concludes that it will be of tmost importance to have a planning team of Tne highest quality to ensure that conditions are maintained so that work can be carried out safely and under reasonable conditions.

Jan 1, 1986