Search Documents

By Walter R. Hibbard

Precipitation in the northeastern United States, Florida, California and in many industrialized areas of the world is now more acidic (lower pH) than can be accounted for by natural causes. At the same time, the acidity of many lakes and streams in the northeastern United States has been measured and found to be similar to that of actual rain. These facts have led to conclusions that the two conditions are related. Coal burning utilities, 700 to 1000 miles upwind, have been accused of being the cause, leading to proposals for strict emission controls on the alleged offenders. The costs of these controls would place an estimated $10 to $15 billion capital burden on utility customers in about 15 states plus $2 to $6 billion annual operating costs. There appears to be no direct well-established scientific evidence that the accused are guilty but that the indictment is based largely on circumstantia1 evidence. This study examines the evidence, describes the situation and proposes what must be done to reduce the acid precipitation in an orderly cost beneficial manner. It is interesting to observe that studies by the different adversaries on the acid precipitation issue come to different conclusions largely because they do not read the same literature, but selectively develop evidence to support their own points of view, This study will try to review the issues impartially and reach a position of scholarly balance.

Jan 1, 1982

By Michael Sheedy

Sulfuric acid is widely used as an electrolyte for the electrorefming and electrowinning or metals. Impurities in this electrolyte are controlled by continuously bleeding solution from the tank house. In addition to the contaminant these bleed streams contain high levels of sulfuric acid and the metal being recovered. Subsequent treatment of these bleed streams often requires neutralization which generates large volumes of solid waste. Absorption resin technology employing a novel ion exchange technique known as Recoflo® allows the separation of the mineral acid from dissolved metal salts. The recovered acid is suitable for recycle back to the electrolyte circuit. The metal salt and other contaminants leave the process free .of the sulfuric acid. In this process, known commercially as the APU®, ion exchange resin is used to sorb sulfuric acid while excluding the metal salts. The purified acid is then removed by washing the resin with water. The process has been extensively used for the recovery of waste pickling acids in the steel industry and anodizing solutions in the aluminum industry. In the mining and metallurgical industries the process has been successfully evaluated for the separation of excess sulfuric acid from copper electrolytes, the removal of magnesium and manganese contaminants from zinc electrolytes, and nickel and copper from copper electrolytes. A full scale installation on a copper refinery bleed stream at Palconbridge's Kidd Creek plant in Timmins, Ontario has now been operating successfully for more than 1 year while pilot field trials have been successfully completed on other applications.

Jan 1, 1997

By BLAKE DAWSON WALDRON

I must acknowledge my strategic adviser, Mr Lance Grimstone, who contributed to the development of this paper, and collated the text and figures.

Jan 1, 1994

By A. McLean, S. Dawson, N. D. G. Mountford

"IntroductionIn order to predict the accepted industrial practice for the year 2000, it may be helpful to first consider the rate of development of scientific knowledge. If the speed with which man can travel on commercial vehicles is taken as a criterion for determining the rate of progression, then it can be seen from Figure 1 that advancement in our present century is very rapid. Likewise, if computer technology is used as a criterion for the measurement of scientific advancement, it becomes evident that technological evolution can be highly exponential. These two examples are sufficient to demonstrate that engineers and managers cannot afford to regard scientific development as being linear with respect to time if they are to avoid underestimating the needs of society.Within this framework of overall development, the time required for individual ideas to progress from inception to regular application has decreased considerably. For example, X-rays first discovered by Roentgen in the 1890's and now used widely in medicine and engineering, required a developmental period of some eighty years. The motorcar evolved from early beginnings at the turn of the century to a position of great social impact in sixty years. Rectifier materials used in high frequency radar to the present explosion in communications, required forty years. As illustrated in Figure 2, the period is shortening rapidly.The use of sound waves appears to be following a similar path. There is now a considerable body of knowledge concerning their behaviour and exceptional advances have been made. In medicine and engineering the sonic approach to examination is well established, and acoustic testing forms the basis of several diagnostic and quality control applications. With respect to metals engineering, ultrasonic testing has contributed to the understanding of the relationship between the size and number of internal defects and the probability of premature failure. This has allowed the designer to incorporate appropriate safety factors in his designs; but more importantly, the realization of the deleterious effect of inclusions on the performance of the final product has resulted in a continuous pressure on the material suppliers to reduce the number of defects in their products.It is not only the designer who is demanding defect free material but also the fabricator, as material breakdown during manufacture can be prohibitively expensive. Examples of this can be found in both the aluminum and steel industries where ultra clean sheet is required to ensure that rejections are minimized during beverage can manufacture and other deep drawing operations."

Jan 1, 1988

By Qinbo Cao, Qianshan Peng, Heng Zou, Xingcai Yu

In this work, a new flotation strategy was proposed for the flotation of rutile. In this strategy, rutile was activated by Pb(NO3)2 and then floated with amyl xanthate (AX) as a collector at pH 8. Pb(OH)+ was the dominant lead species in the solution at pH 8 and is believed to be the major species reacting with the rutile surface. Time-of-flight secondary ion mass spectrometry (TOF-SIMS) study revealed that the lead activation products were well distributed on the rutile surface, and AX− could further bind with the Pb atom on the Pb-activated rutile surface. In this regard, the Pb-activated rutile could be floated by AX. Furthermore, X-ray photoelectron spectroscopy (XPS) analysis indicated that Pb(OH)2 was generated on the Pb-activated rutile surface. The electron transfer during the adsorption of the AX− on the Pb-activated rutile surface was also investigated by XPS analysis.

By Qinbo Cao, Qianshan Peng, Heng Zou, Xingcai Yu

In this work, a new flotation strategy was proposed for the flotation of rutile. In this strategy, rutile was activated by Pb(NO3)2 and then floated with amyl xanthate (AX) as a collector at pH 8. Pb(OH)+ was the dominant lead species in the solution at pH 8 and is believed to be the major species reacting with the rutile surface. Time-of-flight secondary ion mass spectrometry (TOF-SIMS) study revealed that the lead activation products were well distributed on the rutile surface, and AX− could further bind with the Pb atom on the Pb-activated rutile surface. In this regard, the Pb-activated rutile could be floated by AX. Furthermore, X-ray photoelectron spectroscopy (XPS) analysis indicated that Pb(OH)2 was generated on the Pb-activated rutile surface. The electron transfer during the adsorption of the AX− on the Pb-activated rutile surface was also investigated by XPS analysis.

By J. Perlacia

"As the bulk handling sector continues its transformation to Industry 4.0, the mining industry, and its harsh working and environmental conditions, provides a perfect spot to study the feasibility of remote analysis and maintenance of the components used for bulk handling. The most important and expensive tools have been adapted to the digital era in recent years, from remotely controlled haul trucks to monitored conveyor belts.However, the big items of the installations rely on smaller parts that have been leftaside, mainly due to the difficultyof adapting them to the Internet ofThings (IoT).The paradigmatic example is the lack of monitored rollers, while all the other components of the conveyorbelt installations (the belt itself, motors, drums, etc.) were monitored some time ago. The main problem is that a failure of a single roller can cause the stoppage of the entire conveyor, due to possible damage to the belt. Thus, the implementation of an integral monitoring system of all the components of the conveyor is a must.The research and development department of ULMA Conveyor Components has been working since early 2012 on the development of monitored rollers, testing all the problems until their final installation in different demanding conditions, from the extreme heat in Australia to the freezing cold of Norway. All the tests have been done under actual working conditions, in real installations and have provided valuable knowledge in the identification of problems, their solutions and the final advantages of a roller monitoring system.Background and current stateThe malfunction of a single roller in certain conveyor belts can force the standstill of the entire installation until its replacement, due to the risk of greater and more expensive failures, such as a rip in the belt. In the case of a bulk handling installation, where a continuous supply of material is necessary, an unexpected stop of one hour could result in huge economic losses."

Nov 1, 2019

By J. Perlacia

Introduction The Bulk Handling Technology has already started its transformation to the Industry 4.0. Having some of the harshest working and environmental conditions of the industry, the possibility of remote analysis and maintenance of the components seems a perfect target to focus on. The most important and expensive tools have been adapted to the digital era during last years, from remotely controlled haul trucks to monitored conveyor belts. However, these big parts of the installations rely in smaller parts that have been left aside for a while, mainly due to the difficulty to adapt them to IoT (Internet of Things). The paradigmatic example is the lack of monitored rollers whereas all the other components of the conveyor belt installations (the belt itself, motors, drums etc.) were monitored some time ago. The main problem is that a failure of a single roller can cause the stop of the whole conveyor, due to the possible damages to the belt, thus the implementation of an integral monitoring system of all the components of the conveyor is a must. The R&D Department of ULMA Conveyor Components, has been working since early 2012 on the development of Monitored Rollers, facing all the problems until its final installation in very different demanding conveyors, from the Australian extreme heat to the freezing cold Norway. All the tests done under actual working conditions, in real installations, have given a valuable knowledge in the identification of problems, their solution and the final advantages of a roller monitoring system. Background and Current State The malfunction of a single roller in certain conveyor belts can suppose the standstill of the whole installation until its replacement, due to the risk of greater and more expensive failures like the rip of the belt. In the case of a bulk handling installation where a continuous supply of material is necessary, an unexpected stop of one hour could entail huge economical losses. What’s more, many conveyor belts are several kilometers long or the access to some parts of them is very complicated. Due to these difficulties the inspection and maintenance operations can become expensive and hard going, with staff going over the whole area checking the correct condition of the conveyor and rollers, which means a dangerous activity. As in many other industry products, the condition of rollers can be recognized measuring key parameters like the temperature of the bearings, the vibration level etc. The traditional way is to use the characteristic noise of a failing bearing, but this method usually implies to change several rollers because the maintenance team is not able to identify a single source of the noise. In recent years different attempts to measure the temperature of the bearings have been made, but the result is not accurate enough due to the proximity of the rollers in the idlers

Jan 1, 2019

By P. Mundell, R. Torbin

"There are many physical and operational obstacles in pipelines that make the passage of inspection robots impossible including:•,Small radius bends•,Low operating pressure•,Plug valves•,Large changes in pipe size•,No permanent access to the pipeline.The inspection of unpiggable pipelines requires the marriage of a highly agile robotic platform with NDE sensor technology operating as an integrated system. Foster-Miller and GE/PII are developing a robot that is essentially a battery powered, train-like platform. Both front and rear tractors propel the train in either the downstream or upstream direction. Like a train, the platform includes additional ""cars"" to carry the required payloads. The cars are used for various purposes including the NDE sensor module(s), the power supply, and data acquisition/storage components. The robot is designed with a slender aspect ratio and the ability to change shape as required by the physical obstacle presenting itself. The MFL sensor module must also morph itself through the physical obstacles, and thus, will require some level of segmentation. The segmented MFL magnetizers and transformable sensor module represent a major advance in the science of sensor technology and pipeline inspection."

Jan 1, 2005

By M Bloss, B Roberts

BHP Billiton Olympic Dam required a well-tested software product suitable for strategic optimisation and scheduling of options for a potential underground mining project. The company has a standard software package called Blasor® that is used for open pit optimisation of complex deposits such as iron ore, copper-gold-uranium and silver-lead-zinc. It applies a mixed integer programming formulation (MIP) to produce conceptual pushback designs and an optimised pushback sequence. Schedules can then be run on the resulting mine designs. Existing pushback designs can also be imported into the model and an optimum schedule generated. One of the key advantages of Blasor is that multiple strategic mine schedules can be quickly generated according to the various scenarios, options and constraints that are being investigated.It was realised that Blasor, if carefully configured, could be adapted for use in underground planning. The concept of using Blasor as an optimiser for underground strategic scenarios is to represent the underground stope and development data in the form and structure of an open pit mine. In simple terms, underground stoping areas are modelled in the form of pushbacks (phases) with vertical walls. The phase dependency tools in Blasor are used to link mine blocks and their access development drives. These underground phases are imported into the optimiser. Artificial block models are constructed using stope design tonnage and grade data at various fixed cut-offs. A variable cut-off grade model has also been developed using a method of parcels to represent each cut-off grade increment.So far, this approach has been successfully used to investigate the optimum stope design cut-off for various strategic options, the economic potential of a series of mining and processing configurations and to provide guidance on the optimum sequence for developing and mining the various stoping blocks in the resource. Examination of the results has highlighted the most suitable development paths for more detailed study.CITATION:Roberts, B and Bloss, M, 2014. Adaptation of an open pit optimiser for underground strategic planning, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 249–256 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By Gilles Recher, Jörg Riechers, Albert Lueghamer

"INTRODUCTIONIn view of a global trend towards urbanization, more and more trunk sewers and combined sewer overflow tunnels (CSO) with medium to large diameters and the corresponding link sewers are currently built and under design. Shielded tunnel boring machines using segmental lining as tunnel support represent an efficient solution for construction of new wastewater and supply tunnels. Especially in the field of sewers, the durability of concrete structures both exposed to any groundwater present on its exterior and to aggressive waste water as well as gases on its interior is a key requirement. Despite thorough research on segmental lining and mechanized tunneling machinery, conventional thermoplastic liners show comparatively minimal progress in terms of practical advancements. This is in contrast with the development of the latest segment embedded high density polyethylene (HDPE) system. Based on experiences achieved, this paper discusses the latest development of an integral protective lining system in respect of material characteristics and its adaptability to both project and customers’ demands. Reviewed performances, as the bondage behavior of the embedded HDPE system at axial stress loads due to acting thrust cylinders during ring build as well as the ability to drain pressurized water behind the embedded membrane, tested at full scale segments, are also presented. The paper is round off by presenting first details of sewer projects endeavoring to utilize this cutting-edge solution for an integral concrete protection, which will be commenced beginning of 2016.CASE HISTORIES ENCOURAGE ADVANCEMENTS Past experience has shown that unprotected concrete surfaces as well as chemical based linings such as coatings, sprayed linings and cured in-place-systems cannot reach the desired life times. Also the fact that in deep tunnel sewer system hardly maintenance is possible, a durable and maintenance free system is required which only can be reached by applying mechanical anchored HDPE (CPL)."

Jan 1, 2016

By D. Anderson Willis, Alan A. Campoli, Douglas Mynear, Seth Mittle, J. Steven Gardner

"The diversification of energy sources in the United States has seen some major shifts during the past decade resulting from:• A sudden abundance of low-cost natural gas becoming available through advanced horizontal drilling and hydraulic fracturing techniques.• Incentive-driven policies leading to new development in alternative energy.• The emergence of alternative energy sources proliferated as a result of state and federal level incentives and falling capital costs.Coal was once recognized as the primary low-cost fuel source for the generation of electricity in the United States for most of the last century, providing upward of 50 percent of the total generation capacity during much of that period. However, within the past decade, lower-cost natural gas has overtaken coal as the primary source of fuel used in electricity generation, and alternative sources have steadily grown to now account for approximately 10 percent of the overall mix.West Virginia and Kentucky have not experienced the full breadth of the fuel shift, and, as of 2016, still obtained approximately 80-90 percent of electric power generation from coal. However, as coal plants are retired, there has been a shift toward natural gas for new power plants constructed in the region. The economics of power generation (i.e., lowcost fuel source) has typically been the major factor in determining shifts from one fuel source or technology to another. However, governmental energy policies and incentives have more recently been used to promote the development of new alternative technologies such as wind and solar energy growth to diversify the energy mix. The implementation of these incentives has provided some needed traction and resulted in driving the cost of manufacturing and installation of these new wind and solar systems downward to be more cost competitive with conventional fossil-fueled power sources. Future shifts in the generation capacity by fuel type will also be inevitable and impossible to project accurately as policies change and innovative technologies evolve. Determining factors may include the expiration of current incentives, decreasing capital costs, future environmental regulations, evolution of energy storage systems, technical challenges associated with increasing intermittent sources of generation and the development of unforeseen technologies. West Virginia and Kentucky have been among the least solar friendly states, ranking 44th and 48th of the 50 states (Fig. 1 for WV). The ranking of other coal producing states are similarly low:• Ohio 20• Pennsylvania 21• Virginia 38• West Virginia 44• Wyoming 45• Kentucky 48• Alabama 50"

Jun 1, 2019

By Steven B. Van Kouteren

Added value is a term loosely used in the industry, but what exactly does it mean? What does it take to make a value-added product and more importantly how does a company maintain the value added to its products? Most people agree that value-added means the value of a mineral minus the cost to produce it. But what is misleading is that producing value added products does not necessarily guarantee the profitability of the products. In some cases firms that make "value-added" products are not very profitable. It is not only important to understand how to make a value-added product but also how competitive forces in the market can erode the value added. Therefore, when we look at value-added opportunities, we must understand how to obtain the value added and more importantly how to maintain the value. There are four major factors that limit a company's ability to add value to its products. This paper will examine these factors and will use the ground calcium carbonate and mica industries as examples.

Jan 1, 1990

By M. J. dos Santos

"INTRODUCTION In his landmark Society for Mining, Metallurgy and Exploration (SME) 2000 writing, “Theory and Design of Sandwich Belt High Angle Conveyors According to The Expanded Conveyor Technology” J.A. Dos Santos generalized the belt conveyor technology to include all possible variations and augmentations including, particularly, multiple belts along a common carrying and/or return path as is the case most notably in the sandwich belt high angle conveyor technology and belt-on-belt type intermediate (booster) drives. Figure 1, excerpted from his writing, represented the proposition of the generalized “Expanded Conveyor Technology,” abbreviated ExConTec.This formed the basis for the generalization which was completed in theory and in math before 2000 and presented by J. A. Dos Santos at the Y2K SME Annual Meeting. The writing can be found in the SME library (Dos Santos J. A., January 2000). While Figure 1 with the supporting mathematical development solved the generalization, it failed to identify the variation that would prove to have the greatest significance. As with most significant developments, necessity is the mother of invention. This is the case with the Adder Snake belt technology, the subject of this writing. BACKGROUND The concept of elevating bulk materials at a high angle using the sandwich belt concept was first introduced in 1951. That introduction did not produce any lasting success. Commercial success was achieved in the 1970s with the Loop Belt, a sandwich belt elevator of C-shaped profile developed by Stephens Adamson of Canada. The Loop Belt was and is the vital element of a conveyor based self-unloading ship system. Such self-unloading ships have had great success achieving unloading rates above 10,000 t/h with Loop Belts of width to 3,048mm (120”). Being strictly of C-profile, Loop Belts could not be adapted to the general high angle conveying path which is predominantly along a straight incline. It was the success of the Loop Belts that inspired the Dos Santos Sandwich Belts of the 1980s. These expanded the Loop Belt capabilities by producing endless elevating profiles that could take the most direct and/or conforming path between the loading and discharge points. Sandwich Belt high angle conveyor systems have seen great success through the years, with more than 200 installations throughout the world."

Jan 1, 2018

In this paper, three types of value-adding in the minerals industry are discussed: downstream processing, improving the efficiency of existing processing and increasing the knowledge base and expertise of the staff. It is shown that, while downstream processing seems to offer a good way of improving Australia's trade position, there are a number of impediments to such development, notably, limited access to the appropriate technology and overseas markets. Transport costs can also be a problem. To reverse the situation will require more positive policies by government. In the meantime, something can be done towards adding value by increasing the efficiency of existing processes. Examples are given, showing how it might be possible to make economies in reagent costs in the gold industry, how innovative technology has led to more complete processing of a tailings dump, how research might lead to an increase in the throughput in the production of synthetic rutile and how it is possible to leach selectively from gold/copper ores.

Jan 1, 1995

By Caio Moreira, Saulo De Rezende, Nelly Ruíz

The present project sought alternatives for this material through the Mining Lab Beginnings program, which was developed by Nexa in partnership with Escalab to find solutions for the company's highly complex challenges. Through the program, several solutions were evaluated, with additives for the construction market being the most prominent. Tests were conducted to confirm the efficiency of jarosite in the mixture that composes this material. With successful laboratory tests, the technology was tested on an industrial scale, where it also demonstrated its technical and economic viability. The project is now moving into the operational phase, demonstrating that circular economy is the best solution for disposed tailings.

Sep 29, 2023

My predecessor in the office of President of the Institute started a custom of visiting the various local sections, thus obtaining their points . of view and their ideas as to how the Institute can best serve the interests of its members. Exceedingly valuable- exchange of ideas was thus brought about. I am following this custom as far as the limited amount of free time at my disposal will allow me, and I trust that my successor in office will appreciate the benefit to be derived from following the custom thus initiated and will continue the swing around the circle of the local sections. The activities of the Institute are increased by the prestige gained from large numbers and I trust that every member of this local section will consider himself a member of the committee on increase of membership and will see if he is not able during the coming year to gain at least one new member for the Institute. This is a perfectly possible proposition for, although the membership of the Institute is at present approximately seven thousand, I feel sure there are at least seven thousand more men in the United States who are interested in mining, metallurgy or geology from the metal-mining point of view who would make admirable members or associate members of the Institute. The first consideration of the Institute as a body, and of each member as an individual, is to win the war and defeat the Huns. In order to accomplish this, the Institute, as a body, has cooperated with the other national engineering societies and the great bureaus of the Department of the Interior, the United States Geological Survey and the Bureau of Mines in forming committees to study and advise the Government on pressing problems of vital importance.

Jan 5, 1918

By John J. Sammarco

The functional safety of programmable electronic (PE) mining systems is an international issue and concern. From 1995 to 2001, 11 PE-related mining incidents in the U.S. were reported by the Mine Safety and Health Administration (MSHA); 71 PE-related mining incidents were reported in Australia. MSHA does not have regulations for formal evaluations of the functional safety of PE mining systems. Hence, the National Institute for Occupational Safety and Health (NIOSH), in partnership with MSHA and the industry, generated the NIOSH safety framework for functional safety of PE mining systems. An overview of the NIOSH framework is given; the key framework elements, the safety life cycle and safety integrity levels are detailed. The safety framework approach has impacted the national and Australian mining industries by enabling the industries to advance from an ad-hoc approach to a formalized and systematic functional safety process. In retrospect, valuable lessons were learned for addressing functional safety and for changing industry perspectives and practices. These lessons continue to benefit mining and are applicable to other industries as well.

By Shiqiang (Rob) Hui, Jiaren (Jimmy) Jiang, Rees Llewellyn, Yongsong Xie

Wear has been estimated to cost the Canadian mining/mineral processing industry over $15 billion per year mainly for repair/replacement of worn parts in 2013. The associated production loss is difficult to quantify but add considerably to the problem. The Canadian oil sands sector which has to deal with extremely abrasive and erosive solids, has traditionally incurred extremely severe and often unique attack. Demonstrable progress in mitigating the wear problems has been achieved through materials development, more informed materials selections, and better component and operation condition designs. An integral contributor to these advances is a long-term collaborative research partnership between NRC and the mining/supply industry. In this paper, this continuing collaboration will be described. A main focus is to identify degradation mechanisms occurring in the most severe and important service applications and to correlate these findings with laboratory test data. Relevant abrasion and erosion (often combined with corrosion) properties have been established and correlated with composition and microstructures for all classes of resistant materials ranging from relatively soft elastomers to ultra-hard ceramics. A comprehensive wear properties database has been compiled. This capability has been instrumental in facilitating the development of improved materials, optimizing materials fitness/selection for service, wear failure analysis, and quality assurance.

Jan 1, 2015

By A. K. Watt

"The availability of fresh water to meet present and future needs in Ontario is of concern to an increasing number of people. Rain and snow are the source of our potable water and provide, on the average, some 180,-000 billion gallons of water annually. This amount is reduced to 94 billion gallons a day as a result of the evaporation and transpiration of water and our inability to construct the necessary reservoirs for capturing surplus stream flow.The water used for domestic, irrigation, public supply and industrial purposes amounts to some 7 billion gallons daily at present and will reach 21 billion gallons daily by the year 2000; however, only about one-fifth of the water used is actually consumed, and this, along with the possibilities of water re-use, improves the water supply picture still further.The need for adequate pollution control has accompanied industrial and urban expansion and is an important factor in the extent to which our surplus water is used. In the 10-year period since the formation of the Ontario Water Resources Commission, the cost of water and sewage works constructed in the Province has exceeded one billion dollars. A special effort is now being made to control the industrial pollution situation.Numerous federal and provincial agencies are engaged in hydrologie studies in the Province, providing in-formation of benefit to those involved with water resources management."

Jan 1, 1967