Search Documents

By McClelland. John J.

This Bureau of Mines report discusses recent applications of water in-fusion technology to control dust in U.S coal mines and presents recommended guidelines for determining coal seam infusibility. The techniques required to use water infusion are presented in detail. A Bureau case study indicated that water infusion reduced dust levels by 68 pct along a longwall plow face, bringing this section into compliance with the Z.0-mg/m3 Federal dust standard. Similar studies conducted by Occidental Research Corp. under a Bureau contract show water infusion at two longwall double-drum shearer operations produced dust reductions ranging from 38 to 50 pct. Water infusion was found to be cost effective, aver-aging 5 cents per ton.

Jan 1, 1987

By L. L. Oden

The Bureau of Mines has studied a number of processes to remove Cu from molten steel scrap with the objective of determining if any of the laboratory methods studied warranted in depth research investigations. Experimental approaches included oxidizing Cu from steel containing other metals that form stable mixed oxides with Cu (AI, Cr, Fe, Mn, Mo, and V), injecting the same metals as oxides to simplify the mechanism of complex oxide formation, partitioning Cu into alkali or alkaline earth silicate slags or oxide-moderated sulfides, and coremoving Cu and S by injecting active compounds of Ca and Mg. The most promising tests, producing nearly 0.3 pct Cu in the slag, used Ar injection of K20-moderated Na2S-FeS below the surface of molten steel containing about 0.6 pct Cu and protected by a CaO-SiOz slag; however, in depth research investigations currently are not felt to be warranted.

Jan 1, 1987

By N. Greninger

The Bureau of Mines conducted a laboratory study of the measurement of the water and rock dust (RD) contents of synthetic mine-type coal dust (CD) mixtures using a commercial unit for measuring water content and several prototype radiometric units for measuring the RD content. The RD content ranged from 50 to 100 wt pct and the added water (AW) ranged from 0 to 15 wt pct. The total water (TW) content (intrinsic (IW) and AW) of a small dust sample could be readily measured automatically by essentially untrained personnel using a commercial unit. The RD content of a sample containing only IW could readily be measured by moderately trained personnel using several radiometric units. With gamma-ray devices, about 300 g of sample is needed. With the improved beta-ray device, about 25 g of sample is needed. With dry mine dust samples, the estimated RD error range for gamma-ray devices is 0.8 to 2.3 pct and 0.5 to 1.0 pct for beta-ray devices. However, the radiometric measurement of RD content was questionable if the dust mixture also contained AW or if it was uncertain whether the dust mixture contained AW.

Jan 1, 1988

By S. M. Dar

The U.S. Bureau of Mines constructed a full-scale model of a 15-ft-wide coal mine entry to use in combination with finite-element analyses to investigate roof support systems and various types of roof bolts. The objective was to enhance understanding of the fundamental mechanics of the interaction between rock and supports and the relative integrity of bolted mine roof as a function of roof bolt type, length, spacing, and tension, and the basic characteristics of the roof strata. The laboratory test results, when correlated with computer simulations using fmite-element analysis and underground verification tests, should provide a basis for desigillng safer, more cost-effective roof control systems and help to establish guidelines for employing fully grouted resin and mechanically anchored bolting systems. The background for this research, the research approach, the methods and equipment employed, and the results are described in this report.

Jan 1, 1989

By Bernard J. Steblay

The U.S. Bureau of Mines has attempted to use ultrasonic signal travel-time measurements to measure loaded roof bolt strains. The strain measurements are then related to roof bolt loads through equations or empirical calibrations. Such techniques offer the potential of accurate, rapid bolt load measurement that does not disturb the anchotage. This report presents 6e research findings for a specific type of ultrasonic measurement instrument using a pulsed-phase-Iock-Ioop technique. This technique measures signal travel time indirectly by measuring frequency changes. A complete development of the applicable theory and detailed derivations of key equations is presented along with empirical laboratory and field results. The differences between anticipated and measured behaviors are analyzed and discussed. The report identifies problems encountered in applying pulsed-phase-Iock-Ioop technology to roof bolt load measurement and provides potential solutions to many of them. A key assumption of pulsed-phase-lock-loop theory is that driving and reflected signal frequencies will always be equal. Findings showed that not only were actual frequencies not equal but they were not stable or simply related. Reflection wave shape also was not stable. The ramification of these findings and ways to minimize their adverse effects are presented.

Jan 1, 1990

By Nabil A. Bibawy

An improved method for preparing gravimetric standard gas mixtures of helium-4 in nitrogen has been developed by the U.S. Bureau of Mines. A single-pan 12-kg analytical balance that has a sensitivity of 3 mg is used to prepare the mixture. The balance will accommodate a cylinder having a volume of approximately 4 L that weighs approximately 5 kg. The method has been improved to a precision of ±O.04 pct by performing four successive dilutions, by improved handling of gases in the manifold, and by using an improved analytical method to select high-purity gases.

Jan 1, 1990

By D. R. Tesarik

As part of its research program to investigate ways of improving resource recovery and reducing subsidence, researchers from the U.S. Bureau of Mines placed instruments in the B-North ore body of the Cannon Mine, Wenatchee, WA, to monitor cemented backfill and rock deformation during mining. The vibrating-wire gauges proved to be reliable and versatile, and approximately half of the instruments are providing data after 2 years of use. A two-dimensional, finite-element model was used to analyze the Cannon Mine's multilevel bench cut-and-fill mining method and predict rock and backfill displacements. The model accurately predicted rock displacements, but the predicted and measured displacements in cemented backfill had a correlation coefficient near zero, indicating that the model should only be used to predict rock displacements and not backfill displacements. A finite-difference model was also used to evaluate the stability of a cemented backfill pillar. Results can be used to conservatively predict backfill stresses, but on-site observation of pillar failures coupled with in situ measurements are needed to make more accurate predictions. An ongoing evaluation of the mining system has indicated that filling the primary stopes tight to the back with cemented backfill allowed these pillars to carry overburden loads soon after the cemented backfill was placed.

Jan 1, 2010

By Louis E. Dalverny

U.S. Bureau of Mines research to develop diagnostic methods to locate and evaluate fires in abandoned mines and waste banks and techniques to extinguish such fires was applied to an abandoned 60-acre underground bituminous coal mine (Renton, Allegheny County, PA) to locate and extinguish three separated fire zones. Mine fire diagnostics interpret changes from baseline values in subsurface pressures, temperatures, and mine gas composition under imposed pressure gradients induced by a borehole exhaust fan. The effective gas sampling area surrounding each borehole is greatly enlarged. Sampling iterations, using a "communicating" boreholes set, provide "fire signature" information for locating both heated and cold areas. Time-dependent monitoring differentiates heating and cooling periods resulting from combustion front movement and/or fire extinguishment activities. A water injection with fume exhaustion extinguishment effort involved injecting water through boreholes to quench the heated zones while exhaust fans actively removed heated gases from the mine. The technique was ineffective as implemented, primarily because of inadequate spreading of water from the injection points. The Bureau's diagnostic method determined the fire locations and the effectiveness of the water injection with fume exhaustion extinguishment technique.

Jan 1, 2010

By P. L. Swanson

Stability analyses of fractured and faulted rock masses require delineation of the position, extent, and orientation of geologic discontinuities. The size of the smallest active discontinuity that may potentially be resolved using the spatial distribution of microseismic event locations is Limited by the accuracy and precision of the location methods. At a hard-rock mine in the Coeur D'Alene mining district of northern Idaho, two data sets consisting of calibration blast signals from a known source site and origin time and microseismic event signals were recorded using a stope-wide accelerometer array. These seismic signals are used to quantify various sources of error in event location. Five factors influencing source location errors are examined in this U.S. Bureau of Mines study: (1) biases of the numerical source location techniques, (2) receiver array geometries, (3) uncertainties in receiver positions, (4) errors in picking arrival times, and (5) uncertainties in seismic velocity structure, including the effect of mine openings. In addition, synthetic data (accelerometer positions, travel-time picks and wave velocity) are used to determine the effect of known systematic and random errors on source location calculations. It is shown that the commonly accepted association of minimum travel-time residuals with the best location solution does not necessarily hold true when there is a systematic error in seismic velocity. Recommendations are made for increasing the accuracy and precision of locations of microseismic events detected under similar field conditions.

Jan 1, 2010

By August J. Kwitowski

The U.S. Bureau of Mines developed and tested a teleoperating system to control a new highwall mining system. A remote operator was provided out-of-sight sensory information and control of coal extraction and haulage equipment. Surface and production testing proved that the teleoperating system supplied the operator with sufficient sensory information to operate the mining system. Details on the teleoperating system provided in this report include (1) sensor selection, (2) a description of the electronic control system, (3) equipment selection and modifications, (4) the positive test results, and (5) recommendations for system improvements.

Jan 1, 2010

By T. M. Ruff

A prototype mucking machine designed to operate in narrow-vein stopes was developed by Foster-Miller, Inc., Waltham, MA, under contract with the U.S. Bureau of Mines. The machine, called a compact loader-trammer, or minimucker, was designed to replace slusher muckers in narrow-vein underground mines. The minimucker is a six-wheel-drive, skid-steered, load-haul-dump (LHD) machine that loads muck at the front with a novel slide-bucket system and ejects it out the rear so that the machine does not have to be turned around. To correct deficiencies of the tether-remote-control system, a computer-based, radio-remote-control system was retrofitted to the minimucker. Initial tests indicated a need to assist the operator in guiding the machine in narrow stopes. An automatic guidance system that used ultrasonic ranging sensors and a wall-following algorithm was installed. Additional tests in a simulated test stope showed that these changes improved the operation of the minimucker. The design and functions of the minimucker and its computer-based, remote-control system are reviewed, and an ultrasonic-sensor-based guidance system is described.

Jan 1, 2010

By J. L. Kohler

Component failures in the electrical control circuits of mining machines account for a large percentage of the total downtime of the machine, Once a failure has occurred it is always a tedious and usually a time-consuming task to locate the failed component. Moreover, the pressure to quickly locate the cause of a delay can lead to compromises in safety. Thus an onboard diagnostic system, essential for an automated machine, would be a very useful addition to existing machines. This report details U.S. Bureau of Mines development of a generic procedure for synthesizing diagnostic systems for electrical-control-circuit failures in mining machinery. A continuous mining machine is used as the testbed to illustrate the application of the developed methodology. Substantive differences among mining machine control circuits made it impossible to achieve a generic diagnostic system, but a generic approach for the synthesis of the diagnostic system was possible. As the research progressed, it became apparent that an algorithmic approach was better than an expert-system-based implementation. A prototype system was constructed and used to evaluate the diagnostic system. Prototype implementation issues are also examined.

Jan 1, 2010

By Gerald T. Homce

A system capable of monitoring mine electrical power systems and detecting impending component .failure could significantly improve power system safety and reduce unscheduled equipment downtime. Such monitoring would require a method of evaluating electrical parameters, calculated from terminal values, for indications of component deterioration. The U.S. Bureau of Mines has targeted electrical failure of squirrel cage induction motors and examined the use of mathematical models to aid in this evaluation. The initial stage of this work is complete, and has produced polynomial networks called adaptive learning networks (ALN's) that can detect and quantify winding insulation leakage simulated on laboratory motors. In this modeling process, empirical data from laboratory motors were used to select the electrical parameters most significant for assessing? motor conditions, and mathematical expressions relating these parameters to simulated deterioration were formed. ALN's developed thus far can process readily measured motor terminal information and quantify power and current levels of laboratory-simulated leakage to within 1% and 3% of full load values, respectively, for motors in the 10-to 150-hp size range. The next stage of this research is validation of these ALN's for actual motor failures; this stage is currently underway, using accelerated life testing of laboratory motors.

Jan 1, 2010

By Michael J. Pazuchanics

This report documents the current status of the U.S. Bureau of Mines ongoing investigation of the use of adaptive signal discrimination (ASD) systems to distinguish between cutting coal and cutting rock. Cutting-tool forces and vibrations were measured in the laboratory using both conical bits and roller cutters in a linear-cutting apparatus for several material samples and two cutting directions. A number of ASD systems consisting of one or more signal classifiers were trained and tested to study how data window size, type of signal feature, and combining (polling) of classifier results influence system performance. The results show that ASD system recognition rates can be improved by increasing data window size, removing air-cutting portions from the signal data, overlapping data windows, and combining (fusing) information at various levels of ASD system operation.

Jan 1, 2010

By John C. Gagliardi

The size and complexity of modern surface haulage trucks has resulted in an increased reliance upon sensors and electronic-based instrumentation for safe and efficient operation. Design engineers need accurate information about the equipment vibration environment to efficiently and effectively build components for installation on mobile mining equipment capable of withstanding the mine environment. Examples of such components include backup alarms, communication equipment, microprocessor-based controllers, and a wide variety of sensors. Unfortunately, this information is not available to the majority of both original equipment and aftermarket equipment manufacturers. To address this problem, the U.S. Bureau of Mines performed field vibration measurements on a variety of surface mining haulage trucks. The vibration measurements were then analyzed and test specifications were developed in the form of envelopes. In conjunction with test specifications, recommendations to aid manufacturers in implementing a vibration environment test program have been included with an illustrative example.

Jan 1, 2010

By Robert L. Kranz

The U.S. Bureau of Mines (USBM) has been monitoring and studying seismic activity associated with mining in the Coeur d'Alene silver district of northern Idaho. New statistical methods of studying the stope-scale (1-to l00-m) seismicity at one Idaho silver mine are used in this report (part 1) and its companion (part 2). This report deals with methodology and its limitations. The recent concept of fractals and their seismological use is discussed and applied to mining-induced seismicity. Three types of fractal studies are addressed: spatial analyses (including temporal changes of spatial patterns), temporal analyses, and size analyses. Other statistical measures of mine seismicity are also addressed: event mean location, inter-event distance distribution skewness, temporal coefficient of variation, nearest neighbor and next event statistics, and event location planarity patterns. Each of the methodologies discussed (fractal and nonfractal) is presented using sample data from two stopes in the mine. It is shown that stope-scale, mining-associated microseismicity has a fractal nature. The usefulness of demonstrating fractality (scale invariance) for predictive or descriptive purposes depends on recognition of the factors affecting the calculation of fractal dimensions. Several methodological traps are illustrated that can lead to an incorrect conclusion.

Jan 1, 2010

By J. C. Duchon

The use of extended workdays or compressed workweeks (regular shift lengths exceeding 8 h) is attracting growing interest in many industries using continuous operations. While extended workdays promise increased worker satisfaction due to more days off, including weekends and holidays, there are legitimate concerns about the potential effects on the health and safety of such a schedule. The U.S. Bureau of Mines (USBM) conducted a study at a Canadian underground copper, lead, and zinc mining operation that was designed to study the safety and performance implications of extended workdays. Measures were taken before and after a change from the old 8-h continuous schedule to the new 12-h continuous schedule, including behavioral performance measures to analyze perceptual-motor changes, continuous heart-rate monitoring and aerobic capacity to measure physical fatigue, a variety of self-report questionnaires to measure perceived adaption and satisfaction with the new schedule, and pulmonary-respiratory measures to examine air contaminant exposure. Based upon the overall acceptance of the new schedule by the workers and lack of change in fatigue-sensitive behavioral and physiological performance measures, this study recommends that the mine retain the 12-h schedule. However, certain precautionary measures are suggested to insure the safety of the workers.

Jan 1, 2010

By T. M. Ruff

The U.S. Bureau of Mines has developed a portable, inexpensive teleoperation system for mobile hard-rock mining equipment. The system was tested on a compact loader-trammer in a simulated stope. The teleoperation system includes radio remote control and computer-assisted navigation. A recent enhancement includes video cameras mounted on the machine to provide visual information to the operator. This system allows the operator to remain in a safe location while operating the machine from a distance, thus increasing both operator safety and mining productivity.

Jan 1, 2010

By J. K. Whyatt

The U.S. Bureau of Mines conducted an overcore stress measurement on the 5300 level of the Lucky Friday Mine, Mullan, ID, to investigate the stress regime around an experimental stope in a rock-burst-prone mine. The result indicated a stress field with unexpected magnitude and orientation [s 1 ?135 MPa (19,600 psi) oriented S 80° W). An unusual amount of rock-burst activity was encountered during subsequent excavation. A careful review of the overcore data suggested the overcore strain measurements were valid. Moreover, concentrated rock-burst activity suggested that the measured stress field did exist, but was localized and therefore did not represent the far-field in situ stress field.

Jan 1, 2010

By Fred C. Turin

The U.S. Bureau of Mines conducted a human factors analysis of hazards associated with roofholting activities in underground coal mines. Emphasis was placed on hazards related to the movement of the drill-head boom or mast of a roof bolting machine. The objective was to identify hazards and recommend solutions. The data-collection effort consisted of analysis of U.S. Mine Safety and Health Ad-ministration accident data; visits to underground mines and interviews with experienced roof bolting machine operators; discussions with roof bolting machine manufacturers; interviews with workers injured while performing roof bolting tasks; and reviews of research on roof bolting safety. A set of recommendations to increase the safety of roof bolting operations was developed. In particular, the following list of recommendations was presented in ranking order: (1) use an interlock device to cut off power to controls when an operator is out of position, (2) place fixed barriers at pinch points, (3) provide appropriate control guarding, (4) reduce fast-feed speed, (5) use automatic cutoff switches at pinch points, (6) redesign control bank to conform to accepted ergonomic principles, and (7) use resin insertion tools and resin cartridge retainers.

Jan 1, 2010