Search Documents

By D. Brunner

System simulation is an increasingly popular technique for analyzing and improving existing as well as newly designed underground mining operations. An engineering firm that specializes in simulation helped a major metals producer build a long-range planning model of an existing underground mine. Subsequently the team adapted this model to assess technology alternatives in the design of a new mine. The two models differ in the level of detail used for modeling the development process. This paper discusses the differences in approach between the models along with the experiences gained and challenges faced during the construction and use of the models.

Jan 1, 1999

By Narasimha Mangadoddy

The complex nature of multi-phase flow in dense medium cyclones has restricted plant operators and designers to rely on empirical equations for predicting the performance. A number of empirical cyclone models have been developed in the past (Wood, 1990; Dunglison, 2002). In recent years, this subject has been broached with computational fluid dynamics (CFD). Most of the CFD models have not considered the correct rheological behavior of magnetite medium while simulating the medium segregation inside the cyclone. These models mostly predict excessive underflow volumetric flow rates. In this paper simulations of magnetite medium in a dense medium cyclone, were conducted in FLUENT where the particle phases were simulated using the modified Mixture model. The turbulence was resolved using Large Eddy Simulation (LES) model. The rheological behavior of medium was considered in the form of Granular viscosity, Newtonian and Non-Newtonian models corrected with particle loadings and fraction of ultrafines. Multi-phase simulations using granular viscosity option although predict the overall split product medium densities reasonably close to experiments, the mixture viscosity values are restricted to substantially lower values, similar to water viscosity. Simulations using Newtonian viscosity model corrected with particle loading, and fine fraction below 53µm size is predicting overall mixture viscosity levels well over water viscosity levels, but under predicting the under flow the underflow medium density. Multi-phase simulations using Non-Newtonian Herschel-Buckley model, calibrated for superfine magnetite medium measured viscosities, is closely predicting the medium segregation with gamma ray tomography data. Overall predicted product medium densities, underflow volume split are close to the experimental data. This model is can be further used to simulate coal portioning and hence in developing new designs.

Sep 1, 2012

"Load-haul-dump machines (LHDs) are typically used in underground metal mining operations. Delays or inappropriate use of LHDs can result in production loss. Optimized LHD use is especially crucial in larger mines because longer travel distances increase heat, dust, and gas emissions, which in turn increase ventilation costs. This study, conducted at an existing Swedish sublevel cave underground mine, used discrete event simulation and the AutoMod™ DES tool to determine the ventilation costs related to using too many diesel LHDs in a production area with reduced ore pass availability. When fewer ore passes are available, ventilation costs related to operating LHDs in the production area were found to increase by as much as 200, 224, and 306% for one, three, and six LHDs in operation, respectively. ¦ KEYWORDS Discrete event simulation (DES), Loading operations, Production rate, Ventilation costs RÉSUMÉ Dans les exploitations souterraines d’extraction des métaux, on utilise généralement des chargeurs-transporteurs (LHD, de l’anglais Load-haul-dump machines). Les retards ou l’utilisation abusive des LHD peuvent entraîner une perte de production. L’utilisation optimisée des LHD est particulièrement importante dans les grandes mines en raison des longues distances parcourues, lesquelles augmentent la chaleur, la poussière et les émissions de gaz qui, à leur tour, décuplent les coûts de l’aérage. Cette étude, menée en Suède dans une mine souterraine utilisant la méthode d’exploitation en sous étages avec foudroyage, s’est basée sur la simulation à événements discrets (SED) et l’outil de SED AutoMod™ pour déterminer les coûts de l’aérage liés à l’utilisation d’un nombre trop élevé de LHD alimentés au diesel dans la zone de production, avec une disponibilité réduite de la cheminée à minerai. Lorsque les mines disposent de moins de cheminées à minerai, l’étude montre que les coûts de l’aérage liés à l’exploitation des LHD dans la zone de production augmentent respectivement de 200, 224 et 306 % pour un, trois et six LHD en fonctionnement. ¦ MOTS CLÉS coûts de l’aérage, opérations de chargement, simulation à événements discrets (SED), taux de productionINTRODUCTION Transporting material from the mine face to the dumping location requires flexible loading and hauling equipment that is able to cope with sharp curves and a complex mining environment. Load-haul-dump machines (LHDs) are designed for such an environment. Models are available to suit specific features of the working environment such as small, large, or narrow open stopes (Atlas Copco Rock Drills AB, 2007). When carrying a full load, haulage speed is higher for LHDs than for front-end loaders with the same engine size. Also, payloads are approximately 50% higher for LHDs than for front-end loaders (Atlas Copco Rock Drills AB, 2007). LHDs are capable of climbing steep (Bloss, Harvey, Grant, & Routley, 2011). The haulage distance between stope and ore pass is usually between 50 m and 400 m. LHDs are efficient for tramming distances up to 200 m (Bloss et al., 2011), whereas when loading trucks, the LHDs work efficiently when the distance is less than 100 m (Atlas Copco Rock Drills AB, 2007). The largest diesel-powered LHDs, with drive motors of up to 350 kW, can handle a payload of 21 t (Wennmohs, 2014). Most mining equipment runs on diesel fuel, which provides flexibility, high durability, and high efficiency (Pronk, Coble, & Stewart, 2009); however, other alternatives such as electric, hybrid diesel/electric, or hydrogen fuel cell machines are increasingly being developed and used. This change is due to diesel-powered machines accounting for a significant portion of the ventilation costs in the mine (Chadwick, 2008; Paraszczak, Laflamme, & Fytas, 2013). Currently, as part of the European sustainable intelligent mining systems (SIMS) project, Epiroc AB is planning to demonstrate technology for a diesel-free underground mine at Agnico Eagle’s Kittlä mine in Finland using"

Jan 1, 2019

By K Jupp, T J. Howard

Cliffs Natural Resources Pty Ltd (CNR) operates iron ore mines in the Koolyanobbing region of Western Australia, about 50 km north of the town of Southern Cross. Ore is trucked from three geographically isolated sources to the crusher at Koolyanobbing, where it is blended before and during crushing. Lump and fines products are produced and railed to Esperance for ship loading and export to Asian customers. CNR is examining alternative processing paths, from mining to ship loading, with the aim of improving efficiency and reducing costs. Modifications to the system must be consistent with potential future expansions and maintain the low inter-shipment grade variability on which CNR prides itself and has built a strong relationship with its customers. In searching for the optimum process design, many options from mine face to ship loading must be evaluated and compared. Pilot plant studies are infeasible, while complex mineralogical interactions, competing goals and numerous possible system configurations limit the applicability of theoretical analysis. It was therefore concluded that simulation modeling would provide the confidence to take the next step into production trials. This paper describes techniques applied at CNR to simulate grade variability resulting from potential process design changes. The simulation models are easily run Excel-based modules, with each module representing a different part of the process. The modules use extensive Visual Basic macros driven by Excel's user-friendly interfaces. Presentation of the results is enhanced by Excel's excellent graphical capabilities. The simulation software stores and graphically presents time-stamped data from a run, enabling detailed analysis of different process configurations. Final success of a simulation run is measured by inter-shipment variability (standard deviation and process capability) and in-process ore tonnages. Meaningful results from the simulations require the initial input data contain the same correlations present in the real production environment, between the mineral components, production linkages and across time. The data also have to allow simulation of potential changes to mining method and introduction of new pits into the blend. Mining data from the real operations under study are therefore used, with average grades and variability adjusted to match potential future development proposals. It is also necessary to filter out medium and long-term variations from the production data as this variability is best controlled through the conventional medium to long-term mine planning process, not by the process design being studied. The filtering was carried out using a Fourier transform technique, which is described.

Jan 1, 2009

By S. Duvah Pentiah

The transformation of an open pit coal mine to a horizontal-punch underground mine is subject to a number of challenges. These include scheduling the operation of various sizes of trucks over a long period, as well as updating delivery routes and dump site locations as the mine transformation progresses. In this process, rock is excavated from a quarry through earthworks. The bulk earthwork and quarry material delivery were initially drawn from traditional planning and experienced issues in their early phases. As a result, a traffic simulator was developed in order to validate schedules and predict achievable throughput, likely delays or blockages in the long term. The dynamic traffic simulator was also used to provide traffic density and vehicle arrival data at selected intersections in order to identify possible safety and efficiency issues.

Aug 1, 2013

By MáAndrusiewicz, M M. Hilden, M S. Powell, P D. Kay, B Foggiatto

Circuits with unconventional and potentially more complex designs are predicted to become more common in the future as plant designers and operators look to process ores more efficiently. Ideas have been presented on how circuit design may be changed to utilise todayÆs technology to address tomorrowÆs challenges (Powell and Bye, 2009; Powell, Benzer and Mainza, 2011a). High pressure grinding roll (HPGR) installations in various configurations; application of preconcentration plants eg sorting, magnetic or gravity separation; and preweakening devices eg microwave processing; are all examples of technologies having the potential to deliver a significant reduction in comminution energy for ores amenable to these processes. Not only will future novel circuits contain equipment for which models are not as well developed (if at all), many will likely require the ability to respond to variations in feed, and interact with geometallurgical models requiring process adjustments when the ore characteristics change.In order to confidently simulate more complex circuits and accommodate variations in feed type, a significant advancement in modelling and simulation capability is required. This includes dealing with multiple components in the feed, accommodating different competencies of ore, utilising physical separation opportunities and tracking the grade reporting along the different potential processing routes. Developing the means to simulate complex circuits has been a key priority of a collaborative group of comminution researchers working to solve these challenges.Simulations are presented utilising a new configurable simulation interface called the model developers kit (MDK). The MDK is designed to accommodate multi-components and incorporate new models under development. These will be used to demonstrate the potential of flexible circuit design, based on measured ore properties and equipment performance.CITATION:Foggiatto, B, Hilden, M M, Powell, M S, Kay, P D and Andrusiewicz, M, 2012. Simulation of flexible circuits, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 291-298 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By Alejandro Gutiérrez, David Ahues, Paola Merino, Felipe González

A Discrete Elements Method (DEM) study of load movement within a SAG mill 12,192 × 7620 (40′ × 25′) in normal operating conditions is performed. The purpose is to determine how the geometry of the lifters affects the kinetics of the load inside the mill. Specifically, the changes produced by the incorporation of inclined lifters and spiral or helicoidal pulp lifters to the kinetics are evaluated. Four study cases are identified: first, the base case corresponds to a conventional geometry; the second case corresponds to inclined lifters incorporation; third case corresponds to a mill with helicoidal discharge; and the fourth case corresponds to a mill with inclined lifters and helicoidal pulp lifters. To save computational resources, the water that enters the mill has been modeled by varying the coefficient of restitution. The results of a series of experiments are presented to determine how this coefficient varies when having impacts on surfaces with different liquid levels. A comparative analysis is made of the following variables: mean transport speed and material flow, for normal operating conditions. Taking as reference the mill with straight lifters and radial pulp lifters (case 1), the case with the inclined lifters and radial pulp lifters increases the material discharge flow less to 76 mm of size by 5.1%, and this value increases even more when the helicoidal pulp lifters are incorporated reaching a 58.6%. The most significant change is seen in the flow through the grates and the pulp lifters discharge, which can increase substantially improving the operation.

By S. Kenzap, V. Kazakidis

Risk assessment is an essential component of mine feasibility studies. However, it is often challenging to identify the appropriate analysis and derive the required input data. The uniqueness of a mining project and the associated technical issues require customization of the risk assessment approach to meet both requirements and characteristics. The uncertainty driving the operating risk in mine feasibility studies and its assessment through Monte Carlo simulation as a component of a cash flow analysis are discussed in this paper. The paper introduces the use of the analytic hierarchy process for derivation of qualitative input and conducts quantification of the three main sources of operating performance delays, equipment, ground and schedule problems, in a cash flow simulation. A methodology for the assessment of operating risk in mine feasibility studies is presented.

Jan 1, 2011

By A. Paulin, J. Roth, S. Spaic

This experiment was carried out to see whether copper-iron ingots from Late Bronze Age hoards could have been produced by smelting ferruginous copper ores. Since ferruginous copper-ores are chalcopyritic, chalcopyritic concentrate from a present day copper mine was dead roasted in our experiment in lieu of a rich chalcopyritic ore. Charcoal was used as a reducing agent in the reduction of calcine (i.e., a product of dead-roasting), and quartz sand was used as a flux. Two separate metallic solutions, a copper-base and an iron-base alloy, were obtained as a result of two factors: the presence of carbon and the miscibility gap in the Cu-Fe-C system. The metallic melts appeared in a form of bigger or smaller droplets, enclosed by a molten slag which, during the cooling, solidified into metallic beads. The presence of both metals was noticed in the majority of the examined beads. It was therefore concluded that calcine consisted of an intimate mixture of oxides of both metals which were simultaneously reduced during the reduction process. Due to the miscibility gap in the Cu-Fe-C system, separate iron and copper regions were formed in the beads. In both regions, sulphide inclusions were found. The formed molten copper and molten iron solution were found to be saturated solutions. The metallographic analysis revealed the precipitation of iron out of copper and that of copper out of iron during the cooling and solidification of melts. The formed slag contained little iron and no copper oxide.

Jan 1, 2001

By Johannes Labenski, Christian Moormann, Johannes Aschrafi

"Open steel pipe piles are used for various applications in costal engineering, port structures and increasingly important for offshore structures. During the installation of open steel pipe piles the formation of a plug has an influence on the installation process of the pile and also on the final bearing capacity. The formation of the plug depends on different factors, e.g. the pile diameter and the installation method. This paper starts with a structured overview about analytical methods (API, EAP-EAU, UWA-05, HKU-12, Modified API) to calculate the axial bearing capacity of open steel pipe piles. The numerical simulation of the installation process of open steel pipe piles has to fulfill high demands, i.e. to accurately represent the penetration of the pile inside the soil, the formation of the plug and also the stresses and strains during the installation. A numerical back analysis of a comprehensive field test, using the Coupled Eulerian-Lagrangian (CEL) method and a hypoplastic constitutive model for sand, reveals the stresses and displacements of the soil and of the piles. The analysis provides a comprehensive understanding of soilpile interaction.INTRODRUCTIONThe particular difficulty in the numerical simulation of plug formation, is that the effect of plugging inside open ended steel pipe piles has not been fully investigated. In scientific papers different approaches are documented to explain this phenomenon. Some are based on in-situ tests and others are based on numerical simulations. One of the challenges is to determine the end bearing capacity and shaft friction of the steel pipe pile. Different approaches have been developed over the years to determine them e.g. from Randolph et. al. (1991, 1994) and Paik et. al. (2003). Recent approaches are the ICP-05 Method (Jardine 2005), the UWA-05 Method (Lehane 2005) and the HKU-12 Method (Yu & Yang 2012a). A comparison of some methods can be found in Schneider et al. (2010). A plug inside an open steel pipe pile can be visualized as a spatial bracing of soil between the inner surfaces of the pile, cf. Lüking (2010).. However according to Lüking & Kempfert (2012) this bracing only exists for the height in the end of the pile equal to twice its diameter.To identify a plug inside a pile, there are different measurable parameters. One parameter is the development of stresses around the pile during and after its installation. Henke (2013) measured the inand outside horizontal stresses at the pile tip during the installation. The results showed higher stresses on the inside compared to the outside. To validate his measurements he performed a numerical back-analysis of the measured installation process and got matching results."

Jan 1, 2017

By Daniel Lachapelle, Nuri Hmidi, Turgut Yalcin

"Simulation can serve as a convenient tool in studying the behaviour and performance of grinding circuits by facilitating the evaluation of various scenarios and identification of optimum operating conditions. This technique was applied to the St Andrew Goldfields Ltd.’s Stock Mine Mill which is a 1300 tpd gold milling facility, offering custom milling services as well as processing the Company’s own ores. Lack of adequate instrumentation in the mill poses a challenge in attaining optimum performance especially with changing ore types and characteristics. The grinding process is monitored essentially by manual measurement and adjustment of pulp densities at various streams. A simulation program was designed to assist in the effective implementation of this mode of grinding control. Product sizes from both the primary and secondary grinding circuits were correlated empirically to relevant process variables using a database formed from the results of past sampling campaigns. The simulator was created in Microsoft Excel whose data analysis and optimization tools coupled with its Visual Basic Programming capabilities were found to provide an excellent environment for the development of a cost-effective, efficient and user-friendly simulation program.INTRODUCTIONGrinding is often a very costly unit process in milling operations, mainly due to the excessive energy consumption associated with it. For example, for a Canadian copper-zinc flotation mill, grinding was listed as being the most costly item taking up 30.4% of the total milling expenses, followed by the flotation cost at 2 1 .O% (Kidd Creek Mines Ltd., 1982). A survey on 45 copper flotation mills around the world showed the average grinding cost to be 34.5% of the total milling cost (Weiss, 1985).Overgrinding aggravates the cost issue, while insufficient grinding either causes loss of valuable minerals to tails or results in low-grade concentrates. Therefore, it is essential that grinding circuits be carefully controlled and monitored. To this end, a great deal of effort has been devoted over the years to the modelling and simulation of grinding systems in order to assist in the efficient running of these processes."

Jan 1, 2001

By I. B. Fernandes, M. A. Reuter, A. Abadias Llamas

Metallurgical simulation and evaluation of the resource efficiency of whole production processes are of key importance for impact assessment, in terms of environment and resources. Exergy is a measure of resource consumption, taking into account energy, raw materials, water, and chemicals; which allows for the evaluation of different technologies to find the most resource efficient and environmentally friendly process. This paper compares the sustainability for production of rare earth magnets from primary and secondary resources through an exergetic evaluation of the production process, in addition to traditional life cycle assessment (LCA). The methodology makes use of simulation tools for tracking material flow and resources used, based on thermodynamic laws, from ore exploitation to magnet production and recycling. It highlights areas with the greatest potential for improvements in terms of resource consumption and environmental impact generation, having a thermodynamic-validated flowsheet for primary and secondary production of NdFeB magnets, present in several low-carbon technologies, such as wind turbines, electric vehicles, and cooling systems. It demonstrates the minimum exergy destruction for magnet production, through an irreversibility breakdown chart, showing where irreversible material and energy losses occur. Results show that CO2-equivalent emissions for producing NdFeB permanent magnets from primary resources could be twice as high when compared to magnets produced from recycling technologies. The theoretical maximum exergetic efficiency for primary production is 57.61%, whereas for permanent magnets produced from secondary resources, the exergetic efficiency reaches up to 82.89%. Two magnet recycling technologies were evaluated, i.e. in acidic medium and via hydrogen decrepitation, and it was observed that their exergetic efficiency and environmental impact performed better than production from primary resources. Keywords: Resource efficiency, exergy analysis, permanent magnet recycling, process simulation, system design

Jan 1, 2020

By Egnalda Pereira da Silva Pimenta

A umidade nos óleos protetivos temporários e na solução de encruamento, bem como alterações no pH da água desmineralizada, utilizada na lavagem do aço antes do seu oleamento, podem causar manchas na superfície dos aços revestidos com zinco. As condições de transporte e de estocagem nos clientes também podem causar manchas. Essas manchas causam forte impacto visual, podendo gerar dúvidas na aplicação dos aços. Por esse motivo, algumas medidas são utilizadas na Usiminas para evitar manchas, como os controles da umidade no tanque de armazenamento dos óleos, do pH da água desmineralizada e do tempo de estocagem entre o encruamento e o acabamento dos aços. No presente estudo, foram realizadas caracterizações de amostras produzidas e manchadas em laboratório. Foram empregadas técnicas como a microscopia de força atômica, a microscopia eletrônica de varredura com canhão de emissão por efeito de campo e o espectrômetro de emissão ótica por descarga luminescente (GDOES), sendo propostos mecanismos para a formação das manchas que estariam relacionadas com a oxidação superficial do revestimento.

Oct 30, 2017

By A. K. Mahto, B. Samanta

"A heuristic model was developed to simultaneously generate the ultimate pit and production scheduling at a mining project. The method consists of a preprocessing step to select a starter pit, the implementation of a genetic algorithm to optimize the pit and schedule of the starter pit, and a network-flow algorithm–based postprocessing operation to finalize the ultimate pit and production scheduling. Applied to an iron ore mine, the model pit and schedule produced a net present value 21% higher than the reference pit and schedule prepared by experienced field engineers.RÉSUMÉ Un modele heuristique a ete developpe pour generer simultanement l’ordonnancement de la fosse finale et de la production dans le cadre d’un projet minier. Cette methode comprend une etape de pretraitement visant a selectionner une premiere fosse, la mise en oeuvre d’un algorithme genetique pour optimiser la fosse et le calendrier d’execution de cette premiere fosse, ainsi qu’une operation de posttraitement basee sur des algorithmes de flux reseaux pour finaliser l’ordonnancement de la fosse finale et de la production. En l’appliquant a une exploitation de minerai de fer, ce modele de fosse et d’ordonnancement a genere une valeur actualisee nette (VAN) superieure de 21 % a l’approche de reference pour la fosse et l’ordonnancement developpee par des ingenieurs de chantier chevronnes. INTRODUCTIONLong-term planning for an open-pit mine involves two important activities: developing the ultimate pit and determining the optimum production schedule. To accomplish this, an ore deposit is discretized into a number of smallsized elements called blocks, which are presented in a 3D block model structure. Because of economic and slope criteria, only a certain set of mining blocks can be extracted from the deposit constituting a pit. During mining, these blocks must be extracted in a specific sequence known as the production schedule."

Jan 1, 2017

By Martin Dirks

Nowadays the sinter cooler often becomes the bottleneck of the sinter production, with outdated equipment leading to low productivity and high operation and maintenance costs. Furthermore valuable energy is simply destroyed in the cooler, which is not compatible anymore with a cost efficient and environmentally friendly sinter production. Paul Wurth has developed and improved two types of coolers, the annular cooler and the shaft cooler which offer flexible solutions to the specific situation of each client. The classic design of the annular cooler was completely revised and is now composed of a rigid ringframe construction as opposed to the traditional design with individual sintering cars, avoiding the typical problems of centering. Additional features of the PW annular cooler are the low air leakage rate and the increased effective cooling surface due to the removal of dead areas. This leads, in addition to the lower weight, to lower operating costs and a smaller space requirement. The shaft cooler stands out with an even smaller space requirement and a lower sinter outlet temperature because of a very long residence time of the sinter inside the shaft. Its development into a pure counter flow cooler aims at maximizing its energy efficiency, as it is designed as a system with a very low demand for cooling air, high air discharge temperatures and highly reduced dust emissions. For both cooler types flexible heat recovery solutions can be offered. These solutions include the supply of hot combustion air to the ignition hood burners and the sinter strand, the production of steam for the clients steam grid or the production of electric energy.

Aug 16, 2017

By J Pan, T Chun, D Zhu, Z Guo, J M. Young, T C. Ooi

With the rapid development of the Chinese steel industry, the strong demand for iron ores has led to huge imports of various iron ores from all over the world. As a relatively new force in the iron ore world and an important raw material supplier, Fortescue Metals Group (FMG) has achieved an annualised production rate of 100 Mt of iron ore fines. Typical blends were designed to simulate sinter blends employed in Chinese steel mills, and to determine sintering properties and metallurgical performance of blends comprising FMG Rocket fines in pilot sinter pot. It is shown that the sinter of typical blends comprising 15 - 20 per cent rocket fines possesses excellent sintering properties and metallurgical performance. With Rocket fines substitution for competitor ores in a typical customer mill blend comprising fully imported fines, the sinter productivity and tumble index increased from 1.45 t/m2h and 62.0 per cent to 1.54 t/m2h and 64.0 per cent, respectively, while attaining similar reducibility index and reduction degradation index at lower solid fuel consumption.CITATION:Zhu, D, Guo, Z, Ooi, T C, Chun, T, Pan, J and Young, J M, 2013. Sintering and metallurgical performance of blends comprising Fortescue Metals Group rocket fines, in Proceedings Iron Ore 2013 , pp 519-524 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By G S. Beros

In 2019 the Chinese Ministry of Ecology and Environment issued guidelines promoting the implementation of ultra-low emissions in the iron and steelmaking industry. These guidelines aim to drive improvements in air quality through the reduction of particulate matter (PM), sulfur dioxide (SO2) and nitrogen oxide (NOx). Secondly, it also represents an initial means to commence decarbonisation of the industry. The ultra-low emissions guidelines propose that well over 80 per cent of China’s production capacity will achieve these targets by 2025. In response, many sintering operations have implemented numerous improvements to the process that result in significant efficiency gains. Of note is the adoption of deep bed sintering where, with some modifications to equipment, the sintering bed depth is increased resulting in sizable reductions of SO2 and NOx emissions. This paper will also provide an overview of the requirements to introduce deep-bed sintering into an operation and highlight test work completed which quantifies the resultant reduction in emissions.

Nov 8, 2021

By M. F. Almeida

"Due to the randomness of all factors influencing the sintering operation, a two-stepped procedure is proposed to find the best way of using stocked fines at a plant producing Fe-Mn alloys for the steelmaking industry. The approach is based on the following: (1) predict the result of the sintering operation by establishing the best multilinear regression model using some of the characteristics of the loaded material; and (2) find the best solution under a minimizing cost criteria by solving a linear optimization problem using the regression equation plus constraints on the feed and product. IntroductionSome tests carried out using 20% to 30% of sinter in the material loaded into a 60 000 KVA Tysland-Hole electric furnace producing Fe-Mn alloys for the steelmaking industry indicated: (1) a meaningful decrease in the off-gas temperature and, consequently, a better energy use due to the material higher porosity; (2) more uniform heat distribution as a consequence of the electrode reaction zone enlargement; (3) an improved furnace control resulting in a smoother operation; and (4) a decrease in gas production facilitating the off-gas treatment. For some years, this plant used only the coarse fraction of the Mn ores, thus stocking all the received and own-generated fine particles. In view of the mentioned results, a strategy for increasing the use of stocked fines was formulated, including a step where it was necessary to decide which components and respective quantities should be used in the blends to be sintered (Almeida, 1984).It is well known that several factors affect productivity and energy consumption in sinter production, also influencing the product quality. Raw materials characteristics, namely chemical and size composition, affect permeability to gases and may or may not allow a deeper bed. In general, finer ores decrease permeability, increasing electricity consumption by fans, but due to their higher specific surface area, react more completely with other components in the mixture. For coke granulometry, a compromise must be obtained in order not to burn it too quickly nor to widen the flame front, therefore decreasing productivity. Decreasing coke in the blend also acts in sinter bonding, decreasing its consistency and increasing crushing and return fines. Moisture addition also influences components mixing, pre-agglomeration, bed permeability and, consequently, sintering productivity. Therefore, optimum conditions must be established for both a given sintering plant and the components in the feed (Dawson, 1993)."

Jan 1, 1998

By Joaquim Luiz Monteiro Barros

O atendimento as normas ambientais vigentes nos diversos processos das siderúrgicas no Brasil, mais do que uma exigência legal, deve ser um compromisso da empresa com os funcionários, clientes e com a sociedade como um todo. O perfeito dimensionamento do sistema de limpeza de gases e a aplicação de filtros de mangas horizontais é, com certeza, uma alternativa eficiente para solucionar de forma adequada as particularidades e necessidades dos diversos processos siderúrgicos.

Aug 17, 2017

By Renato Ferreira Lima e Corrêa Pereira

Na manufatura de produtos metálicos, o forjamento é o processo de transformação a quente de materiais dúcteis, como aços e ligas, através de conformação mecânica efetuada com esforço de compressão por uma prensa, de modo que eles assumam os formatos desejados. Este processo normalmente é utilizado para produzir peças de formas complexas e com uma maior precisão dimensional de acordo com a especificidade exigida pelo cliente final. Para obter resultados de qualidade, foi necessária a implantação de técnicas de medição indireta de última geração, que proporcionam ganho de tempo e a redução de desperdício de energia e material, além de aumentar a segurança, reduzindo a presença de pessoas próximas aos materiais para medições manuais. O presente trabalho trata da criação de um sistema de visão que, por meio de análise de imagem, é capaz de coletar a medida do perfil de barras em uma Forjaria em tempo real, podendo ser utilizado durante a operação da prensa, para garantir que o material está em conformidade com o especificado. A execução do sistema em produção aponta que as medidas realizadas apresentam desvio máximo de 2mm em relação àquelas realizadas pelos operadores.

Jul 30, 2018