Search Documents

By William Watson

Coal production in the United States in 2010 increased to a level of 960 Mt (1,085.3 million st), according to preliminary data from the U.S. Energy Information Administration (EIA), an increase of 1 percent, or 9.43 Mt (10.4 million st) above the 2009 level of 975 Mt (1,074.9 million st) (Table 1). In 2010, U.S. coal consumption increased in all sectors except commercial and institutional, while total coal stocks fell slightly for the year. Coal consumption in the electric power sector in 2010 was higher by 4.5 percent, while coking coal consumption increased by 37.9 percent and the other industrial sector increased by 7.1 percent. The commercial and institutional sector, which prior to 2008 had been called the ?residential and commercial? sector and is the smallest of all the coal-consuming sectors, declined by 3.1 percent in 2010. (Note: All percentage change calculations are done at the short tons level.) U.S. coal exports increased from the 2009 levels due mostly to higher demand for metallurgical coal, while coal imports decreased for a third year in a row. The increase in coal consumption for electric generation during the year was the consequence of improving domestic economic conditions further bolstered by a cold winter and warm summer in important coal-consuming regions. Preliminary data show that total generation in the electric power sector (electric utilities and independent power producers, including useful thermal output) in the U.S. increased in 2010 by 4.2 percent. Coal-based generation also increased, resulting in a 38-Mt (42-million st) increase in coal consumed in the electric power sector. Coal use in all the sectors other than the electric power sector increased by 13.9 percent to a level of 65.9 Mt (72.7 million st).

Jan 1, 2011

By F. Freme

Coal production in the United States in 2009 de-creased to 972.8 Mt (1,072.8 million st), according to preliminary data from the U.S. Energy Information Administration (EIA). This is a decline of 8.5 percent, or 90 Mt (99.1 million st) below the 2008 record level of 1.06 Gt (1,171.8 million st) (Table 1). In 2009, U.S. coal consumption decreased in all sectors while total coal stocks increased for the year. Coal consumption in the electric power sector in 2009 was lower by 10 percent, while coking coal consumption decreased by 30.6 percent and the other industrial sector declined by 16.6 percent. The commercial and institutional sector (which prior to 2008 had been called ?residential and commercial?) is the smallest of all the coal-consuming sectors and it declined by 8.4 percent in 2009. (Note: all percentage change calculations are done at the short tons level.) U.S. coal exports fell from the 2008 levels, while coal imports decreased for a second year in a row. The decline in coal consumption during the year was the consequence of the domestic economic conditions combined with the weather in 2009, which resulted in lower demand for electricity. Preliminary data show that total generation in the electric power sector (electric utilities and independent power producers, including useful thermal output) in the U.S. decreased in 2009. Coal-based generation also decreased, resulting in a 94-Mt (104-million st) drop in coal consumed in the electric power sector. Coal use in the non-electricity sector decreased by 20.1 percent to a level of 57.9 Mt (63.9 million st). The international coal markets for most of 2009 were reflective of a worldwide economic slowdown. U.S. coal exports and imports both declined for the year. U.S. coal exports totaled 53.6 Mt (59.1 million st). This is a decrease of 20.3 Mt (22.4 million st) from the 2008 level.

Jun 1, 2010

By F. W. Metzger

Coal quality control in mining and mine planning has always been important and has become even more essential in recent years due to environmental considerations. The primary consumers of the sub-bituminous coals found in the Powder River Basin of Wyoming are electric utilities that require low sulfur coals to meet government air quality regulations. Electric generating plants are designed to burn coal of a specific quality, and the supplier of that coal must be able to guarantee shipments within specified quality tolerances. Over the past several years, Exxon Coal USA and, more recently, The Carter Mining Company, a division of Exxon Coal USA have established an evaluation and development program to accurately define the geology and quality of their coal properties. This requires an adequate drill hole density so that detailed correlations of the coal seam and the lithologic sub-units, of the coal seam can be made. These units must be recognizable in the core and also on geophysical logs.

Jan 1, 1981

Pumping coal to market may help Appalachian coal operators increase their share of the eastern seaboard fuel business. Transporting it by pipeline is already an accomplished fact, but until recently it had to be dewatered to be used in boiler furnaces. The campaign for these eastern markets was begun in earnest last November by the widely publicized announcement of successful plant-scale firing of a central station boiler with coal slurry pumped to the burners. This latest advance makes coal similar to oil and gas in convenience in handling and controlling at the consumption end of the pipeline. Slurry could be considered a new commodity for the fuel market. HUGE POTENTIAL MARKET The heaviest concentration of power plants in the U.S. is along the line Washington, Baltimore, Philadelphia, New York and Boston which makes this region the best hunting ground for selling pipelined coal brought from western Pennsylvania and northern West Virginia. Furthermore, if this region is assumed to consume 125 million tons of coal annually, on a comparable basis, the consumption of oil and gas would be about 180 million tons. Even if all of this fuel is not consumed in central stations, it is still a very big market for coal at the right price. Consolidation Coal Co. and Texas Eastern Transmission Co. are trying to line up customers in this area so that a pipeline can be built. This is not to say that there are not many other areas in the U.S. that could not be supplied advantageously by a mine-to-market pipeline.

Jan 1, 1962

By Richard S. Klein

Frozen coal creates severe handling problems. Utilities require uninterrupted supplies of coal to meet their increasing coal consumption rates. Difficulties incurred due to frozen coal result in more costly downtime for the utilities. Air cannons, vibratory hammers and thaw sheds are examples of mechanical devices used to break, crack or thaw frozen coal. Recently chemical treatments have been developed as preventive measures. The freezing of coal depends upon a number of factors, of which one of the most significant is surface moisture. The more there is, the larger the frozen coal problem. Slide 1 depicts a graph of frozen coal compressive strength as a function of surface moisture. Below a certain minimum value the coal will not freeze. Above this point, compressive strength is essentially a linear function of moisture over the range practically encountered. By surface moisture is meant the free moisture on coal having a normal vapor pressure as opposed to capillary moisture or inherent moisture. In addition to the straightforward freezing of coal surface moisture binding particulates together, frost formation occurs due to temperature gradients which develop in rail-cars and stockpiles .

Jan 1, 1980

By J. Keith Haddock

"Introduction The Coal Valley Mine is operated by Luscar Stereo (1977) Ltd. with the Alberta Energy Company having a minority interest. The mine produces 2.0 million tonnes of bituminous thermal coal per year. Deliveries include 1.5 million tonnes to Ontario Hydro and 0.5 million tonnes to the export market via bulk handling facilities on the west coast near Vancouver, B.C. There are a number of mining methods utilized at the mine including open-pit by truck and shovel, strip mining with large draglines and stripping with scrapers. The mine is located 100 km south of Edson, Alberta. Geology The coal measures are concentrated within a 210-metre int~rval of the Paleocene section. The coal seams were originally named by the mining companies in the earliest days of development of the area and these names continue to be used today. Of the five main seams, only three are presently economic to mine based on quality, thickness and depth of cover. These are the Val d'Or, Upper Silkstone and Mynheer. The Coal Valley Mine is located in the structurally deformed foothills area of Alberta and the structure of each mining area is therefore very complex. The general bedding strike is 305 degrees azimuth but major thrust faulting and folding has extensively deformed the natural seams as a closer examination will show. The Mynheer Seam, located at the base of the coal measures, ranges in thickness from 5 m to 10 m and has numerous bentonite and shale partings. Because of inherent geological features, the Mynheer Seam has been subdivided into two zones, the Mynheer 'A' and the Mynheer 'B', and the mining of coal in these zones has necessitated the utilization of distinctly different mining methods. The structural regime of the Mynheer 'A' zone consists of an overturned asymmetrical anticline crest containing a steeply dipping major thrust fault which has raised the seam above the present topographic level. Further extensive shearing and rotation of the coal has resulted in the coal taking a 'pod' shape. The Mynheer 'B' Zone is a continuation to the southeast along strike from the Mynheer 'A' Zone. The bedding dips to the southwest at an average of 12 degrees and is interrupted at the south end by a transverse fault and to the north by its outcrop at the surface."

Jan 1, 1985

By J. D. Price, W. M. Bertholf

In preparing a paper on coal washing in Colorado and New Mexico, it is difficult to refrain from entering into a discussion of the historical aspects of this subject, for the story of coal washing in these states goes back well into the last century. This phase of the subject could well make a complete paper in itself, and of necessity this present discussion must be limited to current operations. Therefore, we are taking into consideration only those washing plants which have operated for some period during the years of 1947 and 1948.

Jan 1, 1949

By George A. Lamb

AMONG the main interesting developments in the coal market have been the changes that have taken place between the consumer groups. Important signs of these changes began to appear many years ago, but in a modest way, and were apparent only to the few fuel experts making broad statistical determinations. It is doubtful, however, that any of these experts appreciated the significance of their early findings, and perhaps none had the imagination to consider how extensive these changes might be eventually with respect to solid fuels sales and distribution. (Reference here will be principally to bituminous coal.) Railroad Fuel Major changes in coal use did become pronounced after World War II, and it did not take an expert to see what was taking place and how serious the impact was likely to be. First, was the case of the steam and diesel locomotives. The railroads had been considered the best coal customers; they were steady and large purchasers and usually paid a better price than most others. Railroad fuel provided the basic mine realization and it often was the source for operating cash during general market slumps. It was the outlet for 20 pct of the bituminous coal production, as much as 110 million tons in 1946.

Jan 2, 1957

By A. T. Shurick

THE NRA Administrator's casual reference to the coal code as the next "pineapple" to be fixed was a conservative estimate of his job. This thorny and adamantine morsel now looms as a critical test of NRA. A failure in coal supplies would have the gravest potentialities in the Administration's program at this time. And the loss of prestige from a breakdown of the enforcement machinery in this initial large-scale test of strength would accentuate the incipient indications of insurrection in other directions. General Johnson has had a difficult task. It involves problems festering for a quarter of a century. A succes¬sion of Presidents have been glad to tide over their respective regimens with inconclusive expedients; they have been baffled by the complexities of the technical angles and hopelessly irreconcilable concepts of powerful conflicting interests with large issues at stake.

Jan 1, 1933

By David Browne

THE use of coal-dust fired reverberatory furnaces, or indeed of reverberatory furnaces of any description, was for the Canadian Copper Co. a matter of necessity, and not of choice. For 20 years smelting had been done in blast furnaces alone, and with the Herreshoff furnaces used prior to 1904 there was no trouble in treating fine ores. But little flue dust was produced, and this, following the time-honored custom, was wetted down and put back with the charge. Whether the flue dust really smelted, or whether it was worn out by being chased around in a circle, was a problem that troubled no one. With the installation of modern blast furnaces and high-pressure blowing engines, in 1904, flue dust commenced to assert itself. Evidently more dust was made than could be smelted, but so many vital problems engaged our attention at that time that this minor question was pushed to one side. In 1906, the details of blast-furnace smelting and the conversion of matte had been worked out to a satisfactory conclusion, and the ever-increasing piles of flue dust and fine ore on the stock yard demanded serious consideration. Numerous experiments in sintering, briquetting, mixing with converter slag, forming blocks of flue dust with green-ore fines and cement, and so on, were undertaken. None of these showed much promise. Our problem, was still further complicated by the question of treating converter slag. The ore was basic, the slag was not needed as a furnace flux, and it was felt that under these conditions the old method of pouring slag in molds and resmelting in the blast furnace was an unnecessary expense. If the converter slag could be settled in basic-lined reverberatory furnaces, in which at the same time flue dust and green-ore fines could be smelted, two problems might thus be solved.

Jan 1, 1915

By George Watkin Evans

The United States Geological Survey has estimated 1 that the State of Washington contains 11,412,000,000 tons of bituminous coal and 52,442,000,000 tons of subbituminous coal, in beds more than 14 inches thick. As the present rate of production is about 4,000,000 tons a year, Washington apparently contains coal enough to supply Pacific coast markets for many years. The character of the coal beds of Washington renders the production of clean coal very difficult, and a considerable proportion of the output is washed before it is marketed. In 1915 Washington ranked fifth among the States in the amount of coal washed, though only twentieth in total output. In that year 37.9 per cent of the coal produced in the State was treated in surface cleaning plants.

Jan 1, 1924

By Albert L. Toenges

Early in 1944 the Chilean Government expressed a desire for assistance from the Bureau of Mines in a study of the coal deposits, coal-mining methods, and preparation and benefication of coals in Chile. A Memorandum of Understanding setting forth the purpose of the work was executed by the United States Government and the Government of Chile. Parts of this agreement are quoted: On February 4, 1944, the Ambassador of Chile in Washington expressed the interest of his Government in obtaining the loan of a mission of experts to assist in the conduct of a survey looking toward the utilization of the low-grade coals of Chile and the application of such technology as may be developed for the distillation of these coals and the use of oil shales. The matter has since been the subject of correspondence between the Secretary of State and the United States Department of the Interior, and the latter Department has agreed to cooperate with the Government of Chile, through the Bureau of Mines, subject to the following understanding:

Jan 1, 1948

By M. Fan, H. E. Wyslouzil, J. Kohmeunch

Eriez HydroFloat(TM) separators and Canadian Process Technologies (CPT) flotation columns have been developed to overcome the limitations of traditional flotation cells in recovering coarse and fine particles, respectively. The flotation column can effectively separate 30-5 µm phosphate. Several industrial-scale HydroFloat separators have been installed in phosphate and potash beneficiation plants. Industrial-scale ultra-coarse (+850 µm) phosphate separation results suggest that a more-than 40% BonePhosphate- of-Lime (BPL) recovery increase and a 37% collector consumption reduction can be achieved. The paper describes the applications of Eriez HydroFloat separators to coarse particle separation and the CPT flotation column to fine/ultrafine particle flotation.

Jan 1, 2009

By David T. Kao

The energy situation the world faced during the decade of the Seventies resulted in actions throughout the free world to reduce its dependence on OPEC oil. Many nations heeded the indicators early in that decade and commenced efforts to reduce their oil requirements. Those nations which did not heed these warnings had the message brought to them more emphatically in the last portion of the decade with the further rapid and continuing rise in prices of OPEC oil. Furthermore, the demonstrated unstable nature of large oil-producing countries has made it clear to all free world nations that their energy demands of the future must be provided for by some more stable and assured supply. Now, early in the decade of the Eighties, we see the need for expanded use of coal as an energy supply to be essential. The result in 1980 and 1981 has been a great increase in demand for steam coal worldwide. In essence, a new business for the United States has developed in steam coal export. In the United States, the large growth in foreign demand for our steam coal is now well recognized and documented. A major impediment in meeting this growing demand became abundantly clear in 1980. This impediment is the congestion existing at U.S. coal export ports. With the recognition of this constraint, a plethora of activity has been observed in announcements for alleviating the problem by improving and expanding current export port facilities. In addition to improvement and expansion, an abundance of totally new facilities has been announced in an effort to find ways to meet this large demand in the new business of steam coal export. This is needed; and hopefully, many of these plans will be translated into action. While total implementation of all stated plans is not expected, much of the implementation depends upon large- scale dredging, large waterside ground storage sites, and improved handling equipments in the conventional type of export ports. The time and capital required for implementation is great, and environmental problems associated with dredging are substantial. Host significantly, and unfortunately, implementation that does include dredging our ports will still not permit use of the truly large colliers of 140,000 DWT and greater, which are evolving as the "state of the art" in long-distance sea transport.

Jan 1, 1981

By Jae-Ho. Lee

Mercury is a toxic contaminant encountered in the extraction of gold from mercury-containing ores. It is found in the leach solution of CIP circuits and in the cathodes of the electrolyte cells used to electrodeposit the gold. The research conducted has examined the potential for selective removal of mercury from synthetic Au-Hg-CN electrolytes containing only gold, only mercury, and both gold and mercury. Cyclic voltammograms were obtained for mercury- coated copper electrodes with these cyanide electrolytes. Exchange current densities were determined from the voltammograms in the low overpotential region. Laboratory scale batch- electrolysis at constant current was also conducted for the electrolytes containing only mercury and both mercury and gold, at 20 and 50°C and from which the kinetic behavior associated with the process was analyzed. The surface of cathode before and after electrolysis was also characterized and a copper mercury intermetallic (CyHg,) was identified. Gold codeposited with mercury during the later stages of electrolysis. The results of this work corroborate that the mercury-amalgam copper electrode offers a viable electrochemical technique for the selective removal of mercury, however a high-surface-area cathode-cell would have to be utilized to provide for the desired selectivity.

Jan 1, 1994

By Pravin Mathur

"Praxair's CoJet® technology was introduced in 1997 to effectively inject chemical energy in electric arc furnaces. Coherent jets were invented as a revolutionary means of injecting oxygen and other gases into the EAF and into converters. Today, steel makers have widely accepted this concept in over 70 EAFs worldwide. Indeed, the whole industry has shifted to this new standard for chemical energy input in EAFs. CoJet® technology has also been implemented successfully in BOF converters.This paper will review the principles of coherent jets as applied to steelmaking. The key learnings garnered from several furnaces are also reviewed. In addition, while the CoJet® program has been widely accepted worldwide, based on steady feedback received from customers and the market place, several programs are underway in development and commercialization. These enhancements and new applications of CoJet® technology are also overviewed in the paper."

Jan 1, 2004

The products from beneficiation present themselves at opposite ends of the spectrum, and yet numerous synergies exist in the preparation of coking coal and hematite iron ore products for their common export markets. Returning to the coal side of the business with Anglo Coal following a five-year sojourn in WA with Hamersley Iron, has provided the opportunity for comparing and contrasting some of the key synergies of the supply chains of both bulk commodities.Comparisons include consideration of things like: resource evaluation (especially quality aspects), run-of-mine handling and preparation, beneficiation, product handling and transportation, quality assurance and customer awareness, value-in-use and impacts on iron and steelmaking, and supply chain environmental aspects.Inherent within these are several other notable contrasts including: æseamsÆ and æorebodiesÆ, rocks and minerals, rejects and tailings, oxidation and weathering, suppliers and users, and marketing and purchasing, to name but a few.This paper covers some of the more interesting of these synergies and raises some potential opportunities for sharing knowledge and innovation between the two areas of activity in the future.

Jan 1, 2005

By D. Swanson

Cold Detonation Physics (CDP) is a patented new field of explosives and the name for the explosive that is produced when non-toxic dry ice (frozen carbon dioxide) is combined with powdered metals such as magnesium and aluminum, which are non-toxic and nitrogen-free. The explosive is detonator-sensitive and detonates according to the rapid reduction of carbon dioxide back to carbon, which produces solids comprised mainly of metal oxides and about 5% carbon. CDP was determined to produce a maximum of 300 liters of carbon dioxide per kilogram (4.81 ft3 /lb) and about 1.5 liters of carbon monoxide per kilogram (0.024 ft3 /lb). Both these figures shift according to metal content where higher metal produces less gases. According to theoretical modelling, the relationship between static pressure and metal content was determined to be an inverse parabolic curve with optimum pressure at 25% to 31% metal, depending on the type/s of metal/s used. Velocity of Detonation (VOD) was determined by measuring light at the wavefront with fiber-optic cable inserted into a series of holes drilled into the side of a 3-inch diameter (76 mm) schedule 40 steel pipe containing the mixture. The highest VOD was observed at 25% magnesium and measured between 2,500 to 4,500 m/s (8202 to 14,764 ft/s) when initiated by a 454-gram (1-pound) booster and an electric detonator. A 25% 50:50 alloy of magnesium and aluminum sample shot at a higher velocity than magnesium, according to how the alloy generated smaller pieces of shrapnel when compared with shrapnel from a magnesium test. CDP, using 25% alloy, was tested for blasting limestone by drilling 3.5-inch holes (89 mm) and inserting a 3-inch x 4-foot cardboard tube (76 mm x 1.22 m) with the mixture, packed to a density of 0.62 g/cm3 . The blast was initiated with an electric detonator, behaved like ANFO with more energy and fractured rock sufficiently across the entire length of the borehole. Seismic analysis determined that CDP produces lower ground vibrations than traditional explosives.

Jan 1, 2024

By Manuel Pérez-Tello, María M. Salazar-Campoy, Óscar Rodríguez-Hoyos

A common problem during the operation of the Kaldo furnace is the formation of accretions and blockage of the injection lance due to splashing. This typically occurs during the processing of anodic slimes for the production of doré. In this work, a 1:7 scale model of the Kaldo furnace currently in operation at Metalúrgica de Cobre, Mexico, was built in transparent acrylic plastic. Water and colored oil were used to represent the doré and slag, respectively. The model was used to determine the maximum penetration distance of the injection lance under a variety of experimental conditions at room temperature. Input variables included two types of oil, rotation speed, inclination angle, and the fraction of the vessel volume occupied by the liquids (φ). A mathematical correlation for the dimensionless maximum penetration distance of the injection lance d ∗ as a function of φ, the Froude number of the liquids in the vessel (Fr), the Reynolds number of the gas jet (Re), and the oil-to-water kinematic viscosity ratio (η)was developed. Reasonable agreement between the calculated and experimental values was obtained. Digital images showed that splashing was caused by the turbulent gas jet impinging upon the free surface of the liquids, whereas the cascade effect was negligible. The results of this work have been useful to improve the operation of an industrial Kaldo reactor.

By Manuel Pérez-Tello, María M. Salazar-Campoy, Óscar Rodríguez-Hoyos

A common problem during the operation of the Kaldo furnace is the formation of accretions and blockage of the injection lance due to splashing. This typically occurs during the processing of anodic slimes for the production of doré. In this work, a 1:7 scale model of the Kaldo furnace currently in operation at Metalúrgica de Cobre, Mexico, was built in transparent acrylic plastic. Water and colored oil were used to represent the doré and slag, respectively. The model was used to determine the maximum penetration distance of the injection lance under a variety of experimental conditions at room temperature. Input variables included two types of oil, rotation speed, inclination angle, and the fraction of the vessel volume occupied by the liquids (φ). A mathematical correlation for the dimensionless maximum penetration distance of the injection lance d ∗ as a function of φ, the Froude number of the liquids in the vessel (Fr), the Reynolds number of the gas jet (Re), and the oil-to-water kinematic viscosity ratio (η)was developed. Reasonable agreement between the calculated and experimental values was obtained. Digital images showed that splashing was caused by the turbulent gas jet impinging upon the free surface of the liquids, whereas the cascade effect was negligible. The results of this work have been useful to improve the operation of an industrial Kaldo reactor.