Search Documents

By L. Wilson, M. Kotzel, T. Pienaar

An empirical equation is presented for the maximum airblast from unconfined charges. This has been tested at a number of sites and with charges ranging from 0.1kg to 311kg. The equation is developed to predict community response to potential explosive test range sites and the testing has added to our knowledge of the effectiveness of mitigating measures. The first site had 10m to 15m high walls that were intended to ameliorate the airblast. These walls functioned to a limited extent and reduced the airblast levels by 2dB to 5dB. The airblast was affected somewhat by topography. Noise levels at the nearest residences exceeded 130dB for charges larger than 1kg, whereas the vibration levels were very small. Formal complaints were received where the airblast level exceeded 128dB as per conventional expectations. Pedestrians and pets in the suburbs were startled by the blasts, emphasizing that the community response is much more sensitive to noise and airblast than vibration levels. The maximum airblast levels were too high for this site to be used on a regular basis. At another site, the airblast levels were significantly increased downwind by up to 10dB due to a moderate wind. A third site, at a quarry, produced unconfined airblast levels beneath the derived limits, but are much higher than the normal quarry blasting. By involving community forums there were no complaints, possibly due to desensitization by the normal blasting activities. The study has highlighted new areas for research in understanding the effect of noise, air blast and vibration on the low cost and informal housing typical in South Africa

Jan 1, 2011

By Carl Lubbe, Ron Frye, Wayne Curtis, Julie Pecori, Dan Leach

Blasting conducted in the USA using the new Electronic Initiation System developed by Altech has shown that an accurate delay system will benefit the customer. Results from test work clearly showed that improved fragmentation was effected and blast vibration was at least similar to that currently found at the test venue with improvements possible.

Jan 1, 1997

By Mark W. Booth

THIS paper deals with the subject of inbye power as the mechanical . engineer sees it, and invites discussion, particularly from the electrical engineer. At the outset, it will be necessary to clear the ground a little by some definite statements. In this question of compressed air versus electricity for the transmission of power and driving of machinery in underground workings, we must see that there are definite fields that compressed air on the one hand, and electricity on the other, can fill to much greater advantage than the other, and in which there can be little or no direct competition, at least for the present. It is under conditions where these fields overlap, and as to where the line must be drawn between the two, that the respective merits of each must be considered. Steam was the first means used to transmit power from the surface of a mine to drive underground machinery, and so long as distances were short and means possible to ensure fairly efficient use of the steam, and where the fire hazard was not in evidence, it gave fairly efficient service. I have in mind an instance during my own connection with the mines-a duplex pump at the shaft bottom at Princess colliery, driven by steam, and which used the steam compound and condensing; and, but for the mechanical difficulties, it was a not inefficient proposition. The steam was taken direct from the surface boiler-plant through a line down the shaft, and used directly at the pump, being in effect a straight conversion from coal to steam to work done. It was the mechanical arrangement, and failure of the pump in that direction, that led to its removal and replacement by something better in the way of an electrically driven turbine pump. Given modern mechanical arrangements, such as a steam-turbine drive on a high-speed turbine pump, and all other parts made in accordance with best practice in the art of steam generation and use, a steam-driven unit fully as economical would have been obtained. But the central electric supply station, and all that that means or promises (not always the same), turned the scale against steam.

Jan 1, 1936

By Neil C. Hario

The purpose of this paper is to explore the various designs and design alternates available for large fine crushing plants, and to discuss objectives and criteria upon which these designs are founded. Common practice for size reduction of run-of-mine or run-of-pit ore in preparation for subsequent treatment utilizes a three-stage system. First stage, or primary breaking is generally carried out with jaw or gyratory crushers. The usual output from this stage provides a feed for fine crushing in the size range of 6 to 10 inches. This discussion is limited to the process of fine crushing, and we will further limit it to what is commonly called secondary and tertiary crushing. We define a large crushing plant as one with a minimum capacity of 2,000 tons per hour. Generally, these plants utilize cone type crushers to reduce ore for rod, ball, or pebble mill feed.

Jan 1, 1970

By J Loimi, P Minkkinen, T Korpela

The head loss caused by metallurgical sampling for slurry streams can be reduced by metallurgical sampler design. When the process volumetric flow rate is reduced by vertical static cutters before the sampling by an equal number of moving cutters to the static cutters, the installation requires less installation head space than other sampling arrangements and is easy to accommodate at suitable locations in the process. Low head loss reduces building costs for the processing plant and operational costs during the lifetime of the plant.The presence of a possible systematic bias in the particle size distribution, solids density and elemental composition between an Outotec MSA 2/50 metallurgical slurry sampler sample and MSA 2/50 manually sampled reject have been studied by a customer. The paired samples were taken as simultaneously as possible. The customer evaluated the possible bias using a paired t-test and provided the assay results to Outotec for further evaluation.The results of the paired t-test showed no systematic bias in particle size distribution, solid density or assayed analytes, except in one analyte with low content and a high relative error. The high relative error in one analyte may have been caused by the same calibration model used in a X-ray fluorescence analyser for both high elemental-content concentrate and very low elemental-content tailings samples. The sampled stream is the tailings of a previous process stage.The results of the t-test were studied further using analysis of variance to reveal the error sources in samples. The results showed no bias between the samples collected from the MSA 2/50 reject and composite samples collected of the MSA 2/50 sample stream. The courier online analyser data was also available for evaluation of representativeness to the process stream.The analysis results of the courier online analysis reveals no bias between the MSA 2/50 reject samples, MSA 2/50 sample stream composite samples and online analysis results during the comparative sample collection period.CITATION:Loimi, J, Minkkinen, P and Korpela, T, 2017. Comparative evaluation of manual sampling and Outotec MSA 2/50 metallurgical slurry sampler, in Proceedings Eighth World Conference on Sampling and Blending , pp 167–172 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By Sup Hong

Herein, concept designs of two different types of mining robots are concerned, which are aimed for developments of deep seabed mineral resources: polymetallic nodules (PMN) and seabed massive sulfides (SMS), respectively. Continuous mining concepts are presented based on technical and environmental feasibility, where the environmental and functional differences for commercial productions are investigated. Needs and roles of versatile mining robots are explained as a key of continuous mining system. The functional requirements and design characteristics of mining robots to satisfy the top requirements from customers are described comparatively. Schemes of axiomatic design and quality function deployment (QFD) are utilized: functional requirements (FR) are defined, technical requirements (TR) are figured out, design parameters (DP) are derived, and degrees of importance of design parameters are evaluated. Analogy and discrepancy in remote operation methods are put side by side. A pilot scale mining robot for PMN and a commercial scale one for SMS are suggested in form of concept designs. PMN mining robot is shaped as a multiple configuration of unit robot modules in side dimension, in which the unit robot module consists of two tracks and two pick-up modules. SMS mining robot is based on a four-tracked vehicle. Main platform is mounted on the vehicle through turn-table. Excavation device consists of two-articulated boom and cutter tool. Crushing-and-pumping units are placed same in both robot platforms.

Jan 1, 2011

By E Niva

The IsaMillÖ is challenging the way that plants are designed and operated. This paper challenges existing designs of concentrator flow sheets, particularly focusing on magnetite circuits.   From what has started out as a small scale ultra fine grinding mill in the pharmaceutical and pigment industries, it has been redesigned and improved upon for mineral processing, and has been the mainstay of fine grinding applications for over ten years. These applications have required energy efficient grinding to succeed, and have been predominately in the base metals industry.   Further development of the IsaMillÖ has now resulted in the machines being able to treat larger tonnages, with higher capacity motors. This development, along with the introduction of purpose designed ceramic media, has allowed the mill to treat courser feed sizes. At the same time, the mill still offers highly efficient grinding, and has enabled it to be operated in coarser tertiary and secondary grinding applications.   The acceptance of the mill in coarser applications, predominately in base metals and PGM applications, has enabled the IsaMillÖ to be a serious contender for beneficiation in other minerals. One such application is the potential for IsaMillsÖ to be part of magnetite flow sheets, which are being considered in Australia to meet the growing iron demand of China. The high energy efficiency of the IsaMillÖ compared to conventional technologies, as well as the smaller infrastructure requirements, provides a great opportunity to reduce the power intensity of magnetite circuits.   This paper will examine the use of IsaMillÖ technology in conventional grinding applications, including recent testwork in a primary grinding base metal circuit, as well as testwork on magnetite ore comparing a lab scale IsaMillÖ with a lab scale Tower Mill.   The growing demand for minerals over the next decade, coupled with higher energy cost, will result in energy efficient technology, such as the IsaMillÖ, being included in standard circuit design.

Jan 1, 2008

By Andrew B. Cecala, Emily J. Haas, Jay F. Colinet

A sociotechnical system (STS) creates a framework that allows an examination of how social and technical factors affect organizational outcomes within a specific environmental context. STS has been rigorously studied with a primary research focus addressing worker-technology interactions. Although these interactions are important, the social processes and interactions that occur whenever any technical or environmental change is introduced into the system have been undervalued. If social processes are better understood, mining organizations could efficiently prepare and stabilize for such changes. With this goal in mind, we sought to extend STS theory through applying principles of meta-design to analyze the results of two case study interventions. Specifically, we studied the impact of an unregulated dust control technology (the Helmet-CAM) and a regulated dust control technology (the Continuous Personal Dust Monitor) on factors within an STS including employees’ knowledge of, communication about, and use of technology to mitigate respirable dust sources. The results are presented in a way that first, addresses the overarching principles of meta-design STS including organizational participation, flexibility, and communication and second, examines how technology implementation processes differ when the organization is complying with a formal, higher-level requirement. Results show that a prominent focus on the social factors within an STS framework could help reduce unpredictability on the technical side and may improve communication within the system to help reduce adoption time, especially if and when accompanying a new, formal work process.

By Andrew B. Cecala, Emily J. Haas, Jay F. Colinet

A sociotechnical system (STS) creates a framework that allows an examination of how social and technical factors affect organizational outcomes within a specific environmental context. STS has been rigorously studied with a primary research focus addressing worker-technology interactions. Although these interactions are important, the social processes and interactions that occur whenever any technical or environmental change is introduced into the system have been undervalued. If social processes are better understood, mining organizations could efficiently prepare and stabilize for such changes. With this goal in mind, we sought to extend STS theory through applying principles of meta-design to analyze the results of two case study interventions. Specifically, we studied the impact of an unregulated dust control technology (the Helmet-CAM) and a regulated dust control technology (the Continuous Personal Dust Monitor) on factors within an STS including employees’ knowledge of, communication about, and use of technology to mitigate respirable dust sources. The results are presented in a way that first, addresses the overarching principles of meta-design STS including organizational participation, flexibility, and communication and second, examines how technology implementation processes differ when the organization is complying with a formal, higher-level requirement. Results show that a prominent focus on the social factors within an STS framework could help reduce unpredictability on the technical side and may improve communication within the system to help reduce adoption time, especially if and when accompanying a new, formal work process.

By L. C. E. FEIO, R. RAMSDEN

In many parts of the world deep level mining relies heavily on the use of refrigeration for providing safe thermal underground conditions. The trend in South Africa in recent years has been to locate the refrigeration plants on surface and to use these plants to chill water that is then distributed throughout the mine. The surface cooling installation normally consists of a pre-cooling tower in which water is first chilled before it is sent to one or more refrigeration plants for further cooling. Presently, the majority of these refrigeration plants use CFC refrigerants; however, to conform with the Montreal Protocol, these plants will have to be replaced or converted for use with alternative refrigerants. The optimum design criteria for installations using the new generation of refrigerants will be affected by their characteristics and are likely to be different from those currently in use. In light of these developments the industry is examining a number of alternative systems for future installations including water vapour refrigeration. Factors that affect the decision on the type of refrigeration system to be used in mine installations are reviewed. INTRODUCTION Gold mining has been carried out in South Africa for over 100 years and most of the reserves close to surface have been mined out; this has led to mining taking place at greater depths, approaching 4000 m below surface. One of the consequences of operating at these greater depths is that it is necessary to install refrigeration plants to cool the ventilation air so as to provide safe and healthy working conditions. With the current low precious metal prices there is pressure on mines to cut costs and in recent years there has been considerable effort devoted to the design of more cost effective and efficient refrigeration plants and cooling systems. In the last 10 years there have been many studies into the use of ice for specific applications (Eschenburg et al., 1986; Hemp, 1988 and Ramsden and Lloyd, 1992) and at present there are three ice making plants in operation on South African mines, each of which produces ice in different processes. In addition, detailed design studies have been carried out on the "split ammonia system" (Napier and Patterson, 1992). In this refrigeration system the evaporator is located underground close to where the cooling is needed, whilst the condenser and heat rejection system is on surface. As far as refrigeration plants are concerned the trend has been to move away from standard package units to custom built refrigeration installations. This has given the design engineer greater flexibility in the choice of key components for refrigeration installations. For example both screw and centrifugal compressors are used, the heat exchangers for the evaporators and condensers may be either plate or shell and tube, and in a number of installations evaporative condensers are used. In addition, the following refrigerants are in use, R12, R22 and ammonia. The acceptance of the Montreal Protocol and its amendments by the South African government will restrict the use of CFC refrigerants and it will be necessary to re-evaluate various refrigeration systems, including those that do not use conventional refrigerants, such as air cycle and water vapour systems, for new surface installations. Although new systems and refrigerants are being developed, only the following refrigeration installations will be compared in this paper: - a refrigeration system using R134a which has properties similar to R12 - refrigeration system using R22 or a new alternative refrigerant with very similar properties - an ammonia refrigeration system - a water vapour refrigeration system The benefits of new cooling systems are not discussed in detail, since they are largely mine specific and outside the scope of the present paper. Since the optimum design for an air cycle system (del Castillo, 1988) is dependent on the mine layout, this system is also not included.

Jan 1, 1993

By Kameron Ray, Ruilin Yang

This paper compares the modeling results obtained by using a single seed waveform (SS) versus multiple seed waveforms (MS) as inputs to the Multiple Seed Waveform (MSW) blast vibration model. The field data for the comparison was collected at a coal mine. The results of the comparison showed that the MSW model yields more accurate predictions and significantly higher correlation to field measurement when using MS as input. When using a single seed waveform as input, different seed waves result in different predictions of PPV. In contrast, using the multiple seed waveforms as an input, more consistent results are obtained.

Jan 1, 2013

By Albert Ladd Colby

A GLANCE through the Bibliography appended to this paper will show that the Transactions of this Institute contain what virtually contitutes a history of the development of the manu¬facture of steel rails in this country and abroad. It is, therefore, fitting that this paper, bringing one branch of this important subject down to date, should be here presented, and it is also appropriate to select this joint meeting of our Society with the Iron and Steel Institute to compare the specifications covering the rails produced in these two countries, and to propose a standard specification to govern the manufacture of American rails for export. During the last ten years the production of Bessemer steel rails in the United States and Great Britain has amounted to 32,128,720 gross tons. Nearly 19,000,000 tons have been rolled in the past five years. The next five years will see an even larger output, owing partly to the extension of railway projects in the Orient, in South and Central America, in Mexico, and in Australia and the other British Colonies. Of late years, the American rail-mills have so largely increased their daily output, that trade conditions have often made possible the delivery of American rails to foreign ports. The tenders submitted by American mills, however, have always been accompanied by requests for changes in the foreign specifications, chiefly in the reduction of the amount of testing required; and it has only been natural, especially at first, that the engineer, whose specification had always been accepted without question by British mills, should interpret American tenders 'as an evidence that an inferior rail would be furnished

Sep 1, 1906

By G Bournival, Y Pan, S Ata

A custom-made set-up that measures bubble coalescence time and the thin film balance (TFB) technique were used to explore the role of residual xanthate (potassium amyl xanthate, PAX) and salt (NaCl) on the adsorption of two frothers (methyl isobutyl carbinol-MIBC, and di-propylene glycolDPG) at the air-water interface. This paper is primarily focused on the comparison of these two techniques in studying the interaction between the flotation reagents and salt emphasizing their capabilities and limits. The results from the coalescence rig showed that the presence of PAX improved the stability of bubbles in both frother solutions and led to a bubble coalescence inhibition at 50–500 ppm DPG. These measures were compared with the results from the TFB. Findings from the TFB were overall in good agreement with the bubble coalescence time, but a higher stability level was observed in thin films under the same condition. The effect of salt on the frother and PAX mixture was also explored, and the results showed an adverse impact of the salt on the interaction of frother and PAX with both techniques. However, variations were found between them in some cases. The TFB is much more sensitive to the presence of dissolved gas and oil droplets.

Aug 24, 2022

By David G. Thompson

There are basically two commonly used methods of drying washed coal. They are mechanical drying (sometimes called dewatering) and thermal drying. The common methods of mechanical drying are by using vibrating screens, cross flow screens, sieve screens or Vor-Siv, vacuum filters and centrifugal dryers. With thermal drying, the common types include direct fired fluid bed, rotary drum, flash or suspension, vertical tray or cascade continuous carrier or vibrating fluid bed dryers and hollow screw dryers. In the past, it has more or less been a general rule that any time the total product is being washed, both mechanical and thermal drying was required. The reason for this was that a product moisture of 3 to 4% was required and thermal drying was and is the only practical method by which this can be accomplished. With the advent of air pollution controls and the ever increasing concentration on dust elimination, a 3 to 4% moisture product is no longer practical in either the preparation plant or in the processing plants which utilize the coal. Under the new standards, it is desirable to have a product with a 6.5 to 7% surface moisture. With this moisture range, dusting, due to handling, will bc kept at a minimum.

Jan 1, 1975

By T Sua, B Wright

"BHP Billiton West Australian Iron Ore (WAIO) conducts an extensive geometallurgy program for its iron ore deposits in the Pilbara with the focus on determining the lump yield (the mass percentage of >6.3 mm rocks) and the lump and fines grade for iron ore products. The geometallurgy program provides accurate information to design engineers and technical marketing teams on the performance of different iron ore mineralogies for future deposits. Additionally geometallurgy results are being used to guide short-term production planning with their introduction into short-term geology models and grade control models. The data that underpins this knowledge is from dedicated geometallurgical programs, drilled using PQ (~83 mm) holes. These holes are crushed by intervals that are based on geological definition which provides an indicative lump yield and lump and fines grade. The lump is then subjected to standard dropping and tumbling test stages to produce a simulated lump and fines product. In the past, quality assurance, quality control holes were drilled using HQ (~64 mm) holes for geochemistry purposes. These holes were crushed to provide an indicative lump yield and lump and fines grade and then 100 per cent is sent for assay (with no dropping and tumbling). Utilising data from HQ holes can significantly increase the indicative geometallurgical data available. This paper compares the geometallurgical results from both PQ and HQ holes from a range of bedded iron deposits (Brockman and Marra Mamba). The PQ and HQ data are compared by orebody, stratigraphy and depth to exclude factors that are expected to influence geometallurgical results.CITATION:Wright, B, Sua, T, Robertson, B and Van Dijken, B, 2016. Comparison of Diamond Drill Size on Iron Ore Geometallurgical Results, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 161–166 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By S. Mischler, J. Organiscak, S. Klima, C. Seaman

"Researchers at the National Institute for Occupational Safety and Health’s Pittsburgh Mining Research Division (PMRD) performed comparative testing of six hollow cone water sprays from three manufacturers: static swirl chamber sprays from Spraying Systems (BD-3, BD-5) and Steinen-Hahn (SH-3, SH-5), and movable swirl chamber sprays from Repair King (RK-3, RK-5). Water flow testing was completed at three operating pressures (60, 80, and 100 psig) where both sets of sprays (3-series and 5-series) produced similar water flows, deviating less than 8% from the average water flow rate at each pressure. Airflow induction testing was completed at 80 psig using a hot wire anemometer to take air velocity measurements upstream of the spray nozzles. Respirable dust capture efficiency testing was completed in a 14.5-m3 (512-ft3) closed system dust chamber at 80 psig. The dust capture efficiency ranged from 7.2% to 9.9% for the 3-series nozzles, and from 5.3% to 7.1% for the 5-series nozzles. Sprays were also analyzed using a Cloud Aerosol and Precipitation Spectrometer (CAPS), which uses light scattering to count and size the airborne water droplets from each spray. In both cases, Spraying Systems sprays produced the largest mean droplet size, followed by Steinen-Hahn and Repair King sprays, respectively. INTRODUCTION Coal mine worker overexposure to respirable coal dust continues to be a problem in underground coal mining operations in the United States. The U.S. Mine Safety and Health Administration (MSHA) now requires coal mine worker respirable dust exposure to be no more than 1.5 mg/m3 average over the actual working shift (CFR 30-70.100, 2016). Potential overexposure to respirable dust by continuous miner, roof bolter, and shuttle car operators may be prevented if proper safety and health practices are implemented as detailed in the mine’s ventilation plan (CFR 30-75.371, 2016). Water sprays are a necessary component of an underground coal mine ventilation plan. They are important on the continuous mining unit for moving air and removing respirable coal dust from the breathable airstream. MSHA requires underground coal mines to include the number, types, location, orientation, operating pressure, and flow rate of operating water sprays in their mine ventilation plans (CFR 30-75.371, 2016). Water sprays can become clogged, requiring the sprays to be properly checked, maintained, and replaced in order to continue meeting the ventilation requirements described in the mine ventilation plan.In an effort to eliminate the problems with spray clogging, Repair King has developed self-cleaning movable swirl chamber hollow cone water sprays (RK-3, RK-5). The spray’s movable swirl chamber is designed to only open when water pressure is applied to the spray nozzle, preventing the nozzle from clogging. Anti-clogging sprays could improve mine production by reducing the amount of time spent servicing clogged sprays. Also, these sprays could improve health and safety of miners since they would continue to suppress and capture dust and continue to move airflow at the face, while a clogged spray loses this ability until it is cleaned or replaced manually. The objective of this research was to assess the comparability of the Repair King sprays with the most commonly used sprays in underground coal mines using performance criteria. An assessment of the sprays self-cleaning or anti-clogging capability was not conducted."

Jan 1, 2017

By F. E. du Plessis

"The distinction between data suitable for process control and data subject to aliasing only becomes quantifiable with the availability of rapid real-time measurements. Expecting the dynamics of flotation to vary for different ore types, process flows and equipment types; a study was conducted to compare the dynamics of different flotation processes. The results shed light on the critical sampling intervals required for process control which in turn allows process stabilization and optimization. The technology used for the in-line measurements is based on diffuse reflective spectroscopy and has been introduced into the mineral processing industry over the past ten years. It has been widely implemented in the sulphide flotation industry in South Africa for the real-time measurement of grade.BACKGROUND AND OBJECTIVE A study was conducted by Du Plessis and Keet (2010) to quantify the minimum sample frequency required for grade and/or impurity control. The study was based on chromite data collected at 15 second intervals from the concentrate line of a flash float cell in the Platinum industry. The data captured the natural process variation of the entrained chromite through water recovery due to changes in feed parameters and flotation performance. It was found that the minimum rate of sampling required from the studied flash float concentrate was 2 minutes. This sampling interval time accounted for 90% of the variance in the process data. It was further found that a sampling interval time of longer than 4 minutes produced data with no significant correlation to reality. The dynamics of the flotation process has been misjudged in the past but can be quantified with the availability of real-time grade measurement based on diffuse reflective spectroscopy. The objective of the study was to compare the dynamics of different sulphide flotation processes through the comparison of maximum sampling interval times required to combat aliasing. All data were collected from single stream analyzers that are currently installed at mineral concentrators. The technology used is based on diffuse reflective spectroscopy."

Jan 1, 2012

By J. G. Craig

This paper initially was to be on the design, construction and operation of the Lucky Friday mill. However, this subject has been pretty well covered in some of the mining publications in the past few years - specifically Mining Congress Journal for April, 1961 and Mining World for March, 1962- : In order to avoid too much repetition, we decided to present in this paper a comparison of the Lucky Friday mill constructed in 1959, and the Mayflower mill built by us in 1962. During the past three years Hecla Mining Company has constructed two relatively small mills: The Lucky Friday mill at Mullan, Idaho 750 T/day; and the Mayflower mill at Heber, Utah - 450 T/day. These mills were engineered, designed and constructed by Hecla, using principally our own personnel, with very little outside (contractor) labor employed. This paper presents a comparison of some of the interesting features of these mills, and where differences occur, it discusses the reasons for the various differences. It compares such points as the testing program, physical layout of the plant, construction costs, the grinding section, the flotation section, tailings disposal, metallurgy, recovery, grades, operating costs, etc. To help illustrate, and to compare these features, we will project pairs of slides showing each of the two mills. First a little background and history on the properties ---

Jan 1, 1964

By C. Musingwini, G. Njowa, M. Burnett, C. C. Birch

From 2022 to 2040, the global demand for mineral commodities is projected to increase by fourfold to six-fold, largely due to traditional drivers such as population growth and urbanisation compounded by the adoption of decarbonisation technologies that are more mineral intensive than fossil fuel technologies. To meet this projected demand, companies operating in the minerals industry should accelerate the development of mineral projects. Since most of the companies generally operate in multiple geographical, regulatory or legislative jurisdictions, it is critical that the information on Mineral Resources and Mineral Reserves they report on in the public domain should be comparable and consistent across different jurisdictions. The Committee for Mineral Reserves International Reporting Standards fosters alignment of national and regional mineral reporting codes through an internationally accepted template that creates common technical understanding of definitions, classification, estimation processes and the Public Reporting of Exploration Results, Mineral Resources, and Mineral Reserves. The Committee for Mineral Reserves International Reporting Standards Template-based codes guide reporting at respective national and regional levels. Since mine planning is critical in the conversion of mineral resources to mineral reserves, a shared technical understanding should aid comparability of mine planning results. However, differences persist in the way mine planning results are reported. Unlike most previous studies, which have primarily focused on comparing mineral reporting codes, this paper updates and extends such comparisons by exploring how similarities or differences in reporting should influence the mine planning process. It also recommends some principle and process changes to assist mine planning professionals to improve consistency and comparability in reporting mine planning results.

Mar 30, 2026

By Salvador Gómez, Rodolfo Espinosa, Jaime Bravo, Leopoldo Gallas

"Compañia Fresnillo, S.A. de C.V. - Proaño Mine, is owned by Industrias Peñoles S.A. de C.V. (Peñoles). The Proaño Mine, is one of the richest silver underground mines in the World, and for this reason, production capacity has always being expanded, based on generated reserves. Reserve generation has not being an easy task as this is a vein type deposit.This paper presents the growing stages at the Concentrator, for about the last twenty years; which can be listed as follows:1.,Increase in capacity from 1,000 to 4,500 tonnes per day, at several stages; on the same infrastructure, and without production interruptions.2.,Addition of a new flotation circuit to recover a zinc concentrate with a high silver content.3.,Installation of a semi-autogenous (SAG) mill, to replace a conventional crushing circuit. 4.,Modernization. Installation of an on stream analyser, an automatic reagent dosification system, 4500 ft3 unit cells, pressure filtration, a closed circuit video system to help process monitoring, an automatic ball addition system for SAG and ball mills, and on-line particle size analysers.5.,Silver recovery from old tailings, installing a 2,350 tonne per day treatment plant.INTRODUCTIONIndustrias Peñoles, S.A. de C.V. (Peñoles)Peñoles’ mission is to add sustainable value to non-renewable natural resources. Peñoles seeks to: build long-term shareholder value; provide customers with the highest quality product services; maintain productive long-term relationship with suppliers; develop and promote the capabilities of their personnel; foster mutually beneficial relationship with the communities in which operates; protect and preserve the environment."

Jan 1, 2002