Search Documents

By Luciana Lezira Pereira de Almeida

De forma geral, as ferramentas diamantadas empregadas no corte de rochas ornamentais são compósitos constituídos de partículas de diamante embebidas em uma matriz metálica. Neste trabalho, para a preparação da mistura das pós, foram utilizados dois processos distintos: o processo convencional utilizando um misturador do tipo cônico e um processo alternativo utilizando um moinho do tipo Attritor. Ambos os processos tiveram a duração de uma hora. Após o processo de mistura, os pós foram sinterizados sob as mesmas condições, pressão de 35MPa e Temperatura de 750oC por um período de 6 mim. Foram produzidos corpos de prova com e sem diamantes. Para a caracterização dos compósitos foi utilizada a Microscopia Eletrônica de Varredura (MEV), Difração de Raios X (DRX), Porosimetria e ensaio de desgaste. Após as caracterizações e testes ficou evidente que os compósitos obtidos a partir da mistura utilizando o moinho Attitor exibiram melhores propriedades, inclusive em relação à compósitos industriais.

Aug 16, 2017

By EFFC/DFI Concrete Task Group

Concrete technology continues to advance rapidly and modern mixes with five components – cement, additions, aggregates, (chemical) admixtures and water – often have characteristics which differ significantly from the older three component mixes – cement, aggregates and water. Recent trends have favoured higher strength classes and lower water/cement ratios, resulting in greater dependence on admixtures to compensate for reduced workability and to meet the (often competing) demands for workability in the fresh state and setting time. The application of testing methods which reflect the true rheological properties of the concrete has not developed at the same rate as the mixes themselves and it is still not uncommon for the slump or flow table test to be used as the only acceptance test for fresh concrete.A joint review of problems in bored piles (drilled shafts) and diaphragm walls cast using tremie methods by both the European Federation of Foundation Contractors (EFFC) and the Deep Foundations Institute in the United States (DFI) identified a common issue. The review determined that many of the problems were caused by (or in part due to) the use of inadequate concrete mixes with inadequate workability, or insufficient stability or robustness of the mixes. It further identified the primary causes as inadequate concrete specifications and inadequate testing procedures. The consequences of these problems are often significant and it has been recognised that spending more time and money on getting the concrete right is the most cost effective approach.A joint Concrete Task Group was set up by EFFC and DFI in 2014 to look at this issue and this guide is the output from that Task Group. A research and development project, funded by the Sponsors of this guide, is being carried out by the Technical University of Munich in conjunction with the Missouri University of Science and Technology. This project includes desk studies, laboratory testing, and onsite testing at worksites in Europe and the US. The research work will be completed during 2016.

Jan 1, 2016

By S. Banisi, M. Poorkani, M. Farzaneh, M. Askari

"At the Sarcheshmeh copper mine 40,000 t of ore per day with an average grade of 0.9 % Cu is ground to 70% passing 75 microns. Grinding is effected in 8 parallel lines of 8 x 5 m ball mills in a closed circuit with cyclones. The make-up balls are 80-mm forged alloy steel balls and the average ball consumption is 750 gh of ore ground. In order to optimize ball size distribution inside the mill, based on the previous investigation instead of using only 80 mm make-up balls a combination of 80 and 60 mm (75% to 25% by weight) ball charge was used in one of the mills. To evaluate the performance of three ball types namely forged alloy steel balls (A), ductile cast iron (C), high chromium cast iron (D) and also a combined (80 and 60 mm) charge of forged alloy steel balls (B), four identical parallel mills were charged accordingly. These four mills were sampled during a period of six months. The amount of material finer than 75 microns of cyclone overflows was selected as a criterion for the performance evaluation. It was observed that in a mill with the combined make-up balls the amount of fine produced was 4% higher than the other mills. The consumption of ball types A, C and D were 730, 710 and 534 g/t, respectively. The results of laboratory flotation tests showed that due to an improvement in the production of fines an increase of 1.4% in the overall copper recovery is obtainable. Due to the promising results, the new make-up ball regime was implemented in all mills in the plant.INTRODUCTIONThe Sarcheshmeh copper ore body which may rank as third or fourth largest in the world contains 1 billion tonnes averaging 0.90 % copper and 0.03 % molybdenum. It is located southeast of Iran and has been processing 40,000 t/d of ore since 1982. The mine produces 100,000 tonnes of copper and 2,200 tonnes of molybednite concentrate per year. After three stages of crushing, the ore with a F80 of 12.7 mm is fed to 8 parallel ball mills in closed circuit with cyclones to produce a product 70% finer than 75 microns. The concentrate of the first stage of flotation is reground and the tailing constitutes the main component of the plant final tailings. A concentrate with an average grade of 31% Cu is obtained after cleaning and re-cleaning stages. Total recovery of the plant varies between 83 and 87 % depending on the operating conditions and ore type."

Jan 1, 2002

By Mahmut Altiner

This study aimed to produce magnesium oxide (MgO) particles with different properties from dolomite ore using an experimental procedure comprising four stages: sample preparation (S1), HCl leaching (S2), precipitation (S3), and calcination (S4). Three different base sources (NaOH, KOH, and NH4OH) were used as precipitant in the third stage to obtain magnesium hydroxide [Mg(OH)2] from a leachate solution, which was obtained in the second stage. Next, Mg(OH)2 particles generated by different alkali sources were calcined at various temperatures from 600–1000 °C for different durations (1–5 h). The effect of these base types on the properties of each product was investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM), Brunauer–Emmett–Teller (BET), atomic force microscopy (AFM), and wet chemical analyses. The experimental results indicated that each product was identified as periclase (MgO) mineral, which was produced with a specific surface area (SSA) of 4.49–44.54 m2 /g depending on the production conditions. The surface roughness of the MgO particles increased with increasing calcination temperature. SEM analyses showed that MgO particles produced at a temperature of 600 or 800 °C were amorphous, indicating that the process was not influenced by the base type, but MgO crystals were smooth when the calcination temperature was 1000 °C. Finally, it was determined from all experimental findings that MgO particles produced via the addition of NaOH have superior properties (such as higher SSA and lower surface roughness) compared with MgO particles produced with KOH or NH4OH as the alkali source. These properties led to great improvement of its usability in industry.

By Mahmut Altiner

This study aimed to produce magnesium oxide (MgO) particles with different properties from dolomite ore using an experimental procedure comprising four stages: sample preparation (S1), HCl leaching (S2), precipitation (S3), and calcination (S4). Three different base sources (NaOH, KOH, and NH4OH) were used as precipitant in the third stage to obtain magnesium hydroxide [Mg(OH)2] from a leachate solution, which was obtained in the second stage. Next, Mg(OH)2 particles generated by different alkali sources were calcined at various temperatures from 600–1000 °C for different durations (1–5 h). The effect of these base types on the properties of each product was investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM), Brunauer–Emmett–Teller (BET), atomic force microscopy (AFM), and wet chemical analyses. The experimental results indicated that each product was identified as periclase (MgO) mineral, which was produced with a specific surface area (SSA) of 4.49–44.54 m2 /g depending on the production conditions. The surface roughness of the MgO particles increased with increasing calcination temperature. SEM analyses showed that MgO particles produced at a temperature of 600 or 800 °C were amorphous, indicating that the process was not influenced by the base type, but MgO crystals were smooth when the calcination temperature was 1000 °C. Finally, it was determined from all experimental findings that MgO particles produced via the addition of NaOH have superior properties (such as higher SSA and lower surface roughness) compared with MgO particles produced with KOH or NH4OH as the alkali source. These properties led to great improvement of its usability in industry.

By A. Danaei, A. McLean, M. Barati, C. Ravindran

"The aluminum industry generates about 90 million tonnes of red mud each year. Previous research shows it could be utilized as a refining flux with a high capacity to absorb phosphorus and sulphur from hot metal in the steel industry. The present study was undertaken to evaluate the melting properties of such fluxes, as it affects the effectiveness of the flux. The results show that the melting behavior of red mud is strongly affected by lime addition and the characteristic melting/softening temperatures reach minimum VALUES (at 32.7 wt% CaO. From these findings, a correlation was established between melting behavior and optical basicity. This allows one to adjust the composition of the flux based on the process requirements. INTRODUCTIONThe aluminum industry generates about 90 million tonnes of bauxite residues each year. This residue is usually red in color because it contains a substantial amount of iron oxide. The red mud, as it is called, is a solid waste with a high concentration of sodium oxide, high pH (10 to 13), and high alkalinity, and thus is harmful to many forms of life. Traditionally, the material is stored in large tailings ponds within the plant’s vicinity (Power, Grafe, & Klauber, 2009). Development of solutions for safe disposal or preferably using this residue for other industrial processes or applications could help restore polluted locations and eliminate a negative impact on the environment (Haake, 1988; Power et al., 2009; Yan & Xuegong, 2010).The mineralogy and chemical composition of red mud depends on the quality of the bauxite and refining process parameters. In general, it consists of iron oxide (Fe2O3), aluminum oxide (Al2O3), titanium oxide (TiO2), sodium oxide (Na2O), silicon oxide (SiO2), and calcium oxide (CaO) (Power et al., 2009). Like most ores and soils, bauxite can contain trace quantities of metals such as arsenic, beryllium, cadmium, chromium, lead, manganese, mercury, nickel, and naturally-occurring radioactive materials, such as thorium and uranium. Most of these trace elements stay in the residue (Power et al., 2009)."

Jan 1, 2012

By Pizhi Zhao, Jingwei Zhao, Zhenshan Liu, Yiheng Cao

"A new Al-Mg-Si-Zn alloy designed for automotive outer panel was trial-produced with industrial procedure. The final product shows a strong planar anisotropy. X ray diffraction analysis shows such strong anisotropy is caused by the dominating cube texture component in the final product. The reason for such high cube texture component was investigated by tracing texture evolution starting from the hot roll slab. It is found that certain cube texture components already exists in the hot rolled slab. The density of cube texture component shows as a wavy change through the following1st cold rolling, inter-annealing, 2ndcold rolling and solution treatment. This study shows that the cold rolling in the laboratory can well represent the texture evolution during the industrial production. The results obtained by lab rolling hints that change of second cold rolling reduction has weak effect on the planar anisotropy, when the gauge of hot rolled slab and final sheet are fixed.INTRODUCTIONWith the rapid progress of light-weighting in the automotive industry, aluminum sheets get more and more application as closure panel and structure parts. Recently the dominating alloy for outer panel is 6xxx series, containing the main alloy elements Mg and Si. The popular gradesareAA6016,AA6111, AA6022, and AA6014. These alloys still cannot satisfy the various requirements from automotive manufacturers. Most suppliers of automotive aluminum sheets are developing their own specific grades according to the customer’s demand. To increase the baking response, anew Al-Mg-Si-Zn alloy was designed, concerning the high combination energy between Zn solutes and vacancies formed during the quenching stage of automotive sheet manufacture. This combination is helpful to the precipitation of ß”phase during the paint baking (Wang, 2015,2016; Yan, 2014).The plastic strain ratio (r value)is a key index of the formability of automotive body sheet. A high r value means a good formability. The r values in different directions can be used to evaluate the planar anisotropy of the metal sheets. The trial produced Al-Mg-Si-Zn sheet shows a strong planar anisotropy with respect to r values. Since the r value is tightly related with texture, the texture evolution from hot roll slab (HRS) to final T4P temper was analyzed with X ray diffraction (XRD) to find the reason for the high anisotropy. Besides, the cold rolling reduction (CRR) was varied in the laboratory to modify the texture distribution, i.e., the planar anisotropy."

Jan 1, 2018

By C. Peña, C. A. Zaror, M. Bustamante, M. Vega

The goal of this paper is to present the carbon footprint of Chilean cathodic copper, as a function of the electricity generation mix, ore grade, and process efficiency. Ore grades and acid leach-solvent extraction-electrowinning (LX-SX-EW) yields in the range 0.5-1.0% and 60-80%, respectively, were considered here. Additionally, electricity supply from two Chilean suppliers, SING (1.0 ton CO2/MWh) and SIC (0.4 ton CO2/MWh) was assessed. Simulation results show that oxide plants located in northern Chile, served by the SING network, feature carbon footprint within 4.3 - 11.4 MWh I ton cathodic copper, as compared with 3.5 - 9.3 MWh I ton copper in plants served by SIC. The footprint was found to increase as ore wade and process yields decrease.

Jan 1, 2011

By Evangelos Petrakis, Kostas Komnitsas

This study investigates the evolution of dimensional properties of grinding products, namely, the mass, the surface area, the length, and the number of particle distributions with the energy input in a ball mill. The size analysis of the mill products enables the calculation of the mass distribution of each material at predetermined size classes and then the determination of the other dimensional properties by taking into consideration the geometry of the particles. Based on the distribution of dimensional properties, an effort was made to determine whether the grinding products are fractal in nature. The effect of material type and grinding conditions on the relationship between the dimensional properties and the specific energy input was also investigated. Special importance was assigned to the study of the specific surface area and the surface area production rate, both during the initial grinding stages and at higher energy levels. The determination of the surface area production rate allows the identification of the grinding limit and the maximum specific surface area which could theoretically be achieved. This approach has as ultimate objective the maximization of energy efficiency and subsequently the minimization of the high grinding cost.

By Evangelos Petrakis, Kostas Komnitsas

This study investigates the evolution of dimensional properties of grinding products, namely, the mass, the surface area, the length, and the number of particle distributions with the energy input in a ball mill. The size analysis of the mill products enables the calculation of the mass distribution of each material at predetermined size classes and then the determination of the other dimensional properties by taking into consideration the geometry of the particles. Based on the distribution of dimensional properties, an effort was made to determine whether the grinding products are fractal in nature. The effect of material type and grinding conditions on the relationship between the dimensional properties and the specific energy input was also investigated. Special importance was assigned to the study of the specific surface area and the surface area production rate, both during the initial grinding stages and at higher energy levels. The determination of the surface area production rate allows the identification of the grinding limit and the maximum specific surface area which could theoretically be achieved. This approach has as ultimate objective the maximization of energy efficiency and subsequently the minimization of the high grinding cost.

By R Crosbie, K C. Runge, E Tabosa, J K. McMaster

Flotation feed density is an operating parameter which is currently not well understood. Most models of flotation only incorporate its effect on particle residence time, but it is likely to have additional effects within both the pulp and froth phases of the machine. Test work was performed in MetsoÆs 3 m3 RCS test rig to investigate the effect of flotation feed density on metallurgical performance. The rig was operated at Rio TintoÆs Northparkes operation using flotation feed and scavenger tail. For each feed, tests were performed at different feed densities, and measurements were performed to estimate the pulp and froth recovery as well as other key flotation parameters (eg bubble size, turbulence and froth stability). Results of this test work have shown that the pulp density does affect key parameters of the flotation process in both the pulp and froth phases. Pulp phase kinetic rates decrease at high density and this is attributed to a reduction in the turbulence within the cell. Froth phase recovery, however, improves presumably because of a stabilising effect due to a greater loading of solids on bubble surfaces.There is a need for more research to be done to better understand these interactions so that metallurgists can determine the optimum flotation feed density to use at a particular operation, or within a section of a flotation circuit.CITATION:Runge, K C, Tabosa, E, Crosbie, R and McMaster, J K, 2012. Effect of flotation feed density on the operation of a flotation cell, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 171-178 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By Howard C. Dunkle

Various factors can affect the quality of B1112 and B1113 steel as produced in a bessemer plant; among them: vessel-charging practice, blowing practice, ingot-pouring practice, ingot delivery-time practice, pit-heating practices, and ingot-rolling practice. Evaluation of the influence of ingot delivery time on quality has been chosen as the subject for this paper because this time is completely within the control of the operator, and on this particular factor there is a tremendous amount of information in the dusty archives of the average steel plant. In order to know how much improvement can be made and when attention should be directed to other factors that influence quality, in the continual struggle for improvement, the effect of ingot delivery time must be accurately evaluated. Once this is done, the importance of other variables can be accurately obtained, thus eliminating the necessity of resorting to opinions that are of doubtful value at best. In the study described herein, extensive use was made of the statistical card system as a method of determining the effect of ingot delivery time as a quality factor in bessemer screw-stock grades by simple direct correlation. The value of this statistical method as a means of accurately determining the influence of various factors has been amply demonstrated by Work1 for the bessemer process and by Hand and Gould2 and Fetters and Chipman3 for the open-hearth process. The quality records of 300,000 tons of bessemer screw-stock billets were used in this study of the effect of ingot delivery time on the rejections for breaks, pipe, check and seams. The reduction in the number of rejections for poor quality reduces the costs and increases the productivity per man-hour. The operator today, more than ever before, must know how to keep costs down, how to do it most quickly and in the best way, and how to obtain the highest quality in line with the ever increasing demands of the customer. It is necessary for him to know the individual relations and interrelations between various factors affecting the quality of the manufactured product if he is to produce material that will meet competitively the cost, performance, and quality demands of the trade. SIGNIFICANCE OF STEEL MANGANESE, MIXER SILICON AND STEEL SULPHUR AS QUALITY FACTORS In order to obtain the highest grade of material it is necessary to control many factors-not just one or two, as operators

Jan 1, 1945

By Hajime Miki, Gde Pandhe Wisnu Suyantara, Tsuyoshi Hirajima, A. M. Elmahdy, Keiko Sasaki

"Seawater has been reported to depress molybdenite in a copper-molybdenum (Cu-Mo) flotation process at high pH due to the precipitation of Mg(OH)2. Meanwhile, to improve mineral recoveries, collectors are usually added into the flotation cells, thus adding the complexity to the mechanism of bubble-particle interactions involved in Cu-Mo flotation. Therefore, understanding the interaction mechanism in seawater flotation and in the presence of collectors is important to explain the minerals depression. The present work investigated the effect of kerosene on the bubble collision and attachment to pure chalcopyrite and molybdenite surfaces in MgCl2 solution as one of the seawater major components at pH 6 and 11. Mineral surfaces were characterized using atomic force microscopy (AFM). In addition, minerals floatability in the same system were tested in a column flotation. The study of bubble-particle interactions shows that following several collisions, bubble could displace the intervening liquid layer on the mineral surfaces, forming a three-phase contact (TPC). A TPC formed more rapidly in the presence of emulsified kerosene in a 0.01 M MgCl2 solution at pH 6 for both minerals. The reason is kerosene increased the surfaces hydrophobicity and destabilized the intervening liquid layer on the surfaces. Moreover, the average time required to form a TPC was shorter on molybdenite surface. This can be attributed to the effect of adsorbed kerosene on molybdenite surface and molybdenite surface roughness.INTRODUCTIONIn froth flotation, bubbles are used to separate hydrophobic mineral particles from hydrophilic particles. In this process, bubble-particle interactions (i.e., collisions, attachment, and detachment) are crucial with regard to mineral recoveries. The effectiveness of froth flotation depends on the formation of stable aggregates between the hydrophobic particles and the bubbles, allowing the bubble to carry the particles to the froth layer. To form such aggregates, the bubbles and particles must collide, and the intervening liquid layer must be drained below the liquid layer critical thickness, forming a stable threephase contact (TPC) (Ralston & Dukhin, 1999). Particles detachment may take place if the particles still have sufficient kinetic energy and the TPC is not formed. Previous studies of bubble-particle interaction in electrolyte solutions have been conducted using atomic force microscopy (AFM) (Assemi, Nguyen, & Miller, 2008), and by approaching the bubble using mica plate (Pushkarova & Horn, 2008), however, these studies did not focus on the bubble-particle collisions. Bubble collisions and attachment to hydrophobic (Teflon) and hydrophilic (glass) surfaces in a a-terpineol solution have been investigated by Krasowka et al. (2003)."

Jan 1, 2016

By R. M. Cooper, H. K. Herbert, D. N. Phillips

A study was carried out to determine the effects of adding CaCO3, Fe, Al and CaSi2 to the ladle, rather than to the raw materials, in order to increase the concentration of Ca, Fe and Al in the final product to meet customer specifications at Simcoa's Kemerton plant in Western Australia. LA-ICP-MS, SEM-EDXRA and ICP-AES analysis of samples and controls showed that the technique is suitable for controlling minor element concentrations. Iron was successfully added, while calcium silicide with aluminium proved better than limestone with aluminium for controlling Ca and Al concentrations in the silicon

Jun 19, 1905

By Isıl Kerti, Sibel Daglılar, Sinem Yıldırım

In this study, effect of rolling and coiling temperature in thermo mechanical controlled process (TMCP), on the microstructure and mechanical properties of dual phase (DP) steel according to martensite volume fraction (MVF) rate was investigated. By using various finishing mill exit temperature and cooling conditions that is controlled laminar cooling system, the microstructural evolution of coil improves the mechanical properties with lower costs and higher productivities, in comparison to the heat treatment after rolling. The main part of the paper contains the result of tensile, yield and microstructure properties of DP600 steel produced on hot strip rolling plant and run- out table line. The results show that a higher MVF and an increasing cooling rate after the last deformation raised strength of the DP600 steel. The yield strength and ultimate tensile strength increase by decreasing coiling temperature.

Jan 1, 2015

By M. R. MacIver, M. Pawlik, H. Alizadeh

Treatment of tailings is an integral component of mineral processing. Tailings with a high clay content are a challenge for the mineral processing industry; e.g. the clay slimes produced from production of phosphate in the mid-western United States and the fine tailings produced from oil sands production in western Canada. Dispersants are a commonly used process aid, but their impact on the structure and settling properties of high clay content tailings is not well understood. The paper describes the changes in composition and bitumen release that occur when mature fine tailings (MFT) are treated with a polymeric dispersant (lignosulfonate.) Synchrotron-source computed tomography (CT) was used to obtain high-resolution 3D images of samples prepared at varying dosages of dispersant. The CT method permits a powerful visualisation of the internal structure and composition of the samples. These insights will enhance our understanding of the structural characteristics of mineral tailings relevant to solid-liquid separation by flocculation and thickening. Keywords: Dewatering, dispersion, dispersants, chemical treatment, computed tomography

Jan 1, 2020

By T. Nghipulile, G. Dzinomwa, J. Kurasha, M. Amwaama, B. Mapani, K. Maweja, T. E. Moongo

The effect of mineralogy on the grindability was investigated using three copper ores – two sulphides and one oxide. The dominant copper minerals were identified by optical microscopy and mineral chemistry derived from SEM-EDS analysis. The sample designated sulphide 1 was borniterich, sulphide 2 ore was mainly chalcopyrite, and the oxide ore was predominantly malachite and minor azurite. The gangue minerals were identified using semi-qualitative XRD analysis. Sulphide 1 contained more than 80% (w/w) of quartz compared to about 70% in the other two ores. The Bond work indices were 13.8, 21.6, and 17.3 kWh/t for sulphide 1, sulphide 2, and oxide ore respectively. This suggested that the chalcopyrite-rich ore is the hardest, while the malachite-rich ore has intermediate hardness, and the bornite-rich ore is the softest. The brittleness indices of the ores were calculated using the chemical composition of the gangue, and a good correlation between brittleness indices and Bond work indices was observed, which highlights the importance of the gangue composition in determining the fracture behaviour of the ores. There is scope for further investigation into the relationship between ore mineralogy and comminution behaviour using other breakage characterization techniques.

Mar 30, 2023

By G. Stokreef, B. R. Davis, M. Kadiyski, T. LeBel, Alvear Montenegro, R. Parra, V. Montenegro

A drop tower and methodology were developed to study the impact of mineralogy on the flash combustion behaviour of copper concentrates. Reaction shaft conditions of a flash furnace were simulated using a drop tower reactor and different molar ratios of oxygen gas to sulphur in the feed. Five feeds were tested in the drop tower including pure minerals chalcopyrite and pyrite as well as two mineralogically distinct copper concentrates and a blend of the two. The behaviour of each of these five feeds were evaluated through analysis of the solid combustion products for elemental sulphur, mineralogy and particle size. Desulphurization curves for each of the feeds were produced. It is thought that the desulphurization behaviour of pure minerals can be used to estimate the behaviour of a concentrate and that a blending recipe could be developed, which can optimize the chemical and mineralogical inputs to the flash furnace and guide operations on the optimum furnace conditions. Overall, the drop tower has proven to be a useful tool for studying flash combustion processes. Experimental results suggest that mineralogy has a significant impact on the conditions required for the production of matte with consistent grade. This finding is especially significant for custom smelters, which may see several different blends in a day. INTRODUCTION Flash furnace smelting is a continuous feed, batch tap, pyrometallurgical process that is used to produce copper matte from copper sulphide concentrates. Dried concentrate(s), silica flux, and secondary materials are blended to a target chemical composition, typically given by the Cu/S ratio, before processing. This fine, dried feed is dispersed throughout the heated furnace reaction shaft with an O2-enriched reaction gas. The particles heat up in the shaft of the furnace, ignite and undergo reactions that pre-oxidize the iron sulphide and some of the impurities in the feed. Oxidation reactions in the shaft of the furnace desulphurize the feed and produce an SO2-containing off gas. The reacted particles fall into the furnace settler and separate into a Cu-rich matte and an iron-silicate slag, while the SO2-containing off gas is carried out of the furnace for heat and dust recovery, as well as H2SO4 production. Some concerns during operation of the furnace are dusting, over or under oxidation of the feed, and a stable flame.

Jan 1, 2019

By Diler Katircioglu-Bayel, Oner Yusuf Toraman, Safak Gokhan Ozkan

One of the most energy-intensive processes for producing submicron range calcite is stirred media mill. In the present work, numerous operating parameters such as solid mass fraction, grinding media size, media filling ratio, and grinding time have been investigated using a vertical type stirred media mill. The results are evaluated on the basis of mean particle size, specific surface area, and specific energy consumption. After conducting this study, optimum experimental conditions found to be as 70% media filling ratio, 25% solid mass fraction, 1 mm grinding media size, and 120 min grinding time. Besides, energy savings up to 22% were achieved with the choice of proper media size.

By Rouzbeh Vakili, Adel M. Hanna

"The application of piled raft foundations has significantly increased during the last few years. In this system, the raft and the pile group collectively transfer the applied building load to the underlying soil layers. Determination of load sharing between the raft and the piles derives the complexity of piled raft designs due to its multi-parameter nature. These parameters are but not limited to: soil density, pile length, pile spacing, raft geometry, and piles installation technique. This study is to examine experimentally the effect of sand density and pile installation techniques on the load sharing mechanism. Experimentally, tests were conducted on a square rigid raft with a single pile in sand under three different soil densities; 30%, 45%, and 60%. The experimental results are used to determine the pile and the raft shares in non-displacement and displacement piled raft systems. The results of this study reveal that soil density changes the load sharing of displacement piled raft; the pile share increases in higher soil density. However, this is not the case in non-displacement piled raft and load sharing is independent of soil density in working loads.IntroductionThe piled raft foundation is a combination of shallow and deep foundation which transfers the superstructure load to the soil by a complex soilstructure interaction. The interacting mechanism among foundation elements and their surrounding soil is illustrated schematically in Figure 1 and could be classified into two categories: (1) pile-soil-pile and (2) pile-soil-raft. The pile-soil-pile interaction is the same as the free standing pile group and is a function of pile spacing and pile installation method. Pile-soil-raft interaction, which only involves in piled raft foundation design, could be affected by: the length, spacing, and roughness of the pile, the rigidity and dimension of the cap, soil condition, and the pile installation method. Pile-soil-raft interaction could have favourable and unfavourable effects on bearing capacity and settlement, respectively. The pressure between the cap and the soil favourably increases the horizontal stress on the pile shaft and consequently increase the shaft resistance. Whereas, this pressure induces negative skin friction on the piles which increases the settlement. The pile-soil-raft interaction mainly controls the load sharing mechanism of piled raft foundation when pile spacing (S) is more than 3.5dp."

Jan 1, 2017