Search Documents

By Larry Stolarczyk

A clear vision of the future coal mining industry was developed into a hierarchy of technology needs by the National Mining Association (NMA) and the Chief Executive Officers of the mining industry. Although improvements in safety and environmental factors were the main drivers in the technology roadmapping workshop sponsored by the Department of Energy, the agile mining machine of the future must efficiently extract coal from deeper, thinner, and more geologically complex coal beds. One of the challenges will be to develop sensors and software that enable clean coal cutting in a changing geologic environment. The roadmap identifies imaging ahead of raining and horizon control within the top ten needed technologies. For these technologies to be adopted by the mining industry, they must be proven to be effective while driving down mining cost and risk. This paper describes how three-dimensional imaging ahead of mining and horizon sensors enable improved ground control and safety in the mining of underground coal.

Jan 1, 2003

By W. Petruk

Imaging is a fundamental requirement when characterizing minerals, ores and related products. Images are used for presentation, texture analysis, characterization, image analysis, identification, etc. The image mode that is utilized is dependent on the application, mineral properties and available instruments. Different instruments produce images that display different features. In order of increasing complexity they are: hand specimens, a non-polarizing microscope, polarizing optical microscope, scanning electron microscope (SEM), low vacuum SEM, microprobe, secondary ion mass spectrometer, staining, cathodoluminescence, tomography and others. Image analysis uses images produced with either an optical microscope or a SEM, but the SEM images are superior in this application. Key words: Mineralogy, Imaging, Mineral characteristics, Scanning electron microscopy, Optical microscopy, Cathodoluminescence

Jan 1, 2003

By W. Petruk

Imaging is a fundamental requirement when characterizing minerals, ores and related products. Images are used for presentation, texture analysis, characterization, image analysis, identification, etc. The image mode that is utilized is dependent upon the application, mineral properties and available instruments. Different instruments produce images that display different features; in order of increasing complexity they are: hand specimens, a non-polarizing microscope, polarizing optical microscope, scanning electron microscope (SEM), low vacuum SEM, microprobe, secondary ion mass spectrometer, staining, cathodoluminescence, tomography and others. Image analysis uses images produced with either an optical microscope or a SEM, but the SEM images are superior in this application.

Jan 1, 2001

By Boyd Davis, Brook Zaback

"Among the first published papers from Prof. Torstein Utigard was work on imaging the aluminum electrolysis process and in-situ measurements of aluminum in cryolite melts. He and Prof. Jim Toguri used an x-ray radiographic technique to measure interfacial tension of aluminum drops. Publications using this equipment for aluminum electrolysis spanned from 1985 to 2006. As well, other methods were used to better understand electrolysis in molten salts, including hot-stage microscopy, direct observations from above the bath and water modeling techniques. For chloride systems (for magnesium and lithium), it is possible to see side-on the electrolysis using a quartz cell. In honour of Prof. Utigard’s contribution to this field, this paper presents a summary of work on visualization of molten salt electrolysis, including work done at the authors’ labs and others around the world. The paper will summarize key findings and their possible impact on molten salt electrolysis."

Jan 1, 2015

By A Cornelius, P Connor, S Fraser

Iron ore mining is a major source of export income for Australia. However with the decreasing reserves of high-grade, low-phosphorus hematite ore, there is mounting pressure to provide consistent mineralogical ore grade. Enhanced 3D characterisation and modelling are crucial to respond to these exigent requirements. To tackle this problem a revolutionary mine-based, imaging system (based on Visible Near Infrared û Short Wave Infrared reflectance spectroscopy û VNIR-SWIR) has been developed. This innovative, CSIRO-built prototype produces mineralogical maps that will have a major impact on ore grade characterisation. Australian iron ore companies will benefit immensely by pioneering this emerging and unique mining technology. The significance of VNIR-SWIR reflectance spectroscopy is well demonstrated with field portable spectrometers and airborne hyperspectral systems. At the mine-scale level, this newly developed imaging system will allow accurate and objective mineralogical mapping of mine faces and benches with very closely spaced sampling. These spectral mineral maps will improve deposit delineation and bring accurate and objective ore grade characterisation that will minimise drilling and enhance ore recovery. This will in turn lead to cost saving and better long-term block model planning. This system will also improve safety for mine geologists in providing mineralogical information at a distance, avoiding the need for any close contact with the mine face. The mine imaging concept is a logical response to the industry need for automatic and objective tools for sustainable and future mining practices.

Jan 1, 2002

By Gregg A. Swayre, Roger N. Clark, Stephen J. Sutley, Kathleen S. Smith

Imaging spectroscopy is a relatively new remote sensing tool that provides a rapid method to screen entire mining districts for potential sources of surface acid drainage. An imaging spectrometer known as the Airborne Visible/InfraRed Imaging Spectrometer (AVIRIS) measures light reflected from the surface in 224 spectral channels from 0.4 - 2.5 µm. Spectral data from this instrument were used to evaluate mine waste at the California Gulch Superfluid Site near Leadville, Colorado. Here, the process of pyrite oxidation at the surface produces acidic water that is gradually neutralized as it drains away from mine waste, depositing a central jarosite zone surrounded by a jarosite + goethite zone, in turn surrounded by a goethite zone with a discontinuous hematite rim zone. Leaching tests show that pH is most acidic in the jarosite and jarosite + goethite zones and is near-neutral in the goethite zone. Measurements indicate that metals leach from minerals and amorphous materials in the jarosite + goethite and jarosite zones at concentrations 10 - 50 times higher than from goethite zone minerals. Goethite zones that fully encircle mine waste may indicate some attenuation of leachate metals and thus reduced metal loading to streams. The potential for impact by acidic drainage is highest where streams intersect the jarosite and jarosite + goethite zones. In these areas, metal-rich acidic dace runoff may flow directly into streams. The U.S. Environmental Protection Agency estimates (U.S. EPA, 1998) that mineral maps made from AVIRIS data at Leadville have accelerated remediation efforts by two years and saved over $2 million in cleanup costs.

Jan 1, 2000

By M. D. Vance, G. R. Corbett, S. D. Butt

Surface wave imaging is a relatively new seismic technique that generates subsurface depth images without having to drill boreholes into the ground, and is rapidly becoming a standard tool in non-destructive geotechnical characterization. This paper presents a case study of the application of these surface wave techniques to image shallow abandoned mine workings at the Montague Gold Mines district near Dartmouth, Nova Scotia. This district has numerous steeply dipping narrow vein workings from historical mining activity, and has actively subsiding and collapsing crown pillars. Due to the rugged conditions at the site and the relative narrowness of the openings (often less than 1 m), a surface seismic system was developed that had improved portability and lateral resolution over other available seismic imaging systems. Seismic surveys were conducted over two sites where independent evidence indicated the presence of shallow mine workings. At one site, a comparative gravity survey was also conducted. The seismic data was processed to generate velocity vs depth images. Overall, the velocity images show vertical zones of zero velocity in the same lateral positions where historical mapping, current subsidence and gravity surveys indicate the presence of steeply dipping workings. Further, the velocity sections are consistent with the thickness of the till cover at each site and the possible weakening of crown pillars at one of the sites.

Jan 1, 2005

By Steve Johnston, Mowafak Al-Jassim, Fei Yan, Omar Sidelkheir, Alain Blosse, Katherine Zaunbrecher

"Imaging techniques are applied to multi-crystalline silicon wafers and solar cells throughout the production process. Photoluminescence imaging, both band-to-band and defect-band, is used to characterize defects and wafer quality at all process steps. These steps include bricks sawn from ingots, wafer sawing, cleaning and texturing, emitter diffusion, edge isolation and glass removal, anti-reflective coating/passivation, and metallization of finished cells. Bricks, wafers, and cells can be imaged at a rate commensurate with in-line measurement, giving spatial information to characterize quality and defect content. Photoluminescence images on silicon bricks can be correlated to lifetime measured by photoconductive decay and could be used for high-resolution characterization of material before wafers are cut. The defect areas in as-cut wafers are compared to imaging results from electroluminescence and lock-in thermography, and cell parameters of near-neighbor finished cells, showing correlations to efficiency, open-circuit voltage, and short-circuit current.IntroductionImaging techniques can rapidly characterize material quality and defect density. Photoluminescence (PL) imaging can be applied to silicon from the brick level to all wafer process steps [1-8]. At the brick level, material thickness allows for measurement and correlation to lifetime where surface recombination effects are minimized [6, 7]. At the as-cut wafer level where thin unpassivated wafers prevent accurate lifetime assessment due to surfaces, defects can still be categorized and quantified to predict finished cell performance [3-5]. Defect regions can be identified by recombination-limited band-to-band PL or by defect-band emission [9-12]."

Jan 1, 2012

By S. Leroy

Grinding is the most energy consuming step in mineral processing, however, it is still poorly understood and its efficiency is difficult to monitor. Mill performances are traditionally measured at the mill discharge, on the basis of a mass percentage passing a certain sieve. This approach does not reflect what happens to the fines through milling. On another hand, if many macroscopic parameters, such as the percent solids of the pulp, its viscosity, or its mean residence time in the mill are known to be related to grinding efficiency, the link between these parameters and particle size distribution (PSD) is still unclear. Here, a methodology is established to understand the effect of ball mill operating conditions on particle size and shape distribution in the grinding process. The study focuses on the particular case of an Upper Group 2 (UG-2) platinum ore concentrator. Due to the very low grade of sulphide and PGM (Platinum group metals) in UG-2, grinding mechanisms are entirely control by gangue minerals. These two minerals have contrasted properties and PGM content and these properties immediately affect the entire recovery process. So, the grinding of both gangue minerals is studied on a size by size basis. At particle scale, three parameters are addressed: particle size, particle composition and particle shape. The specific behavior of chromite and silicate grains is demonstrated. As a conclusion, this study gives some clues to operate ball mills in a more efficient manner regarding chromite issue in the processing of UG-2. Keywords: ball milling control, UG-2, chromite, fine particle, particle shape, segregation

Sep 1, 2012

By V. R. Voller

The WTBAL computer program for evaluating material balances for minerals processing flowsheets was developed at the MRC and has been in general use for a number of years. This paper reports on two enhancements to the basic MTBAL routine. The original program accounted for errors in the process measurements and used estimates of measurement variability to calculate stream weights. Unfortunately, the estimate of measurement variability was fixed over all streams. In the enhanced version of MATBAL, named IMTBL, the program equations and their solution procedure have been modified to allow the estimated variability in a process measurement to vary from stream to stream. The .second enhancement involves making MTBAL interactive. As such, the user now prescribes his information in an easy-to-use fashion in a conversational mode via a terminal. Finally, an assessment of the feasibility of implementing IMTBL on microcomputer systems will also be reported.

Jan 1, 1982

By Tyler Ross, John Tatom, Lon Lantis

The Institute of Makers of Explosives (IME) began development of a Quantitative Risk Assessment (QRA) tool, IMESAFR (Institute of Makers of Explosives Safety Analysis for Risk), in 2005 as a technology transfer effort with the United States Department of Defense (US DoD). Version 2.0 of the software has been developed over the last two years and introduces many new features and upgrades. Key upgrades include a new map-based user interface, new debris density hazard models, a metric version, and additional user options referred to as “conservatism switches”.

Jan 1, 2014

By Vladimir S. Zharov, Vyacheslav A. Tsukerman

"Conceptual imitative dynamic model of developing enterprises for medium and long-term period permitting to ensure coordination of interests of the enterprise and territorial environmental authorities has been developed to enable the process of the prognostication and management of a concentrating mill development, in which a symbol language and terminology familiar to the manager of the company are applied. An algorithm of practical application of this model of company development was elaborated as well as a general methodological approach to the prognostication of the development and procedures of its implementation. The general methodological approach to the implementation of the model has been defined. Within the framework of system approach, a concentrating mill is considered as a subsystem of an ore mining and processing company or a mining and smelting one. A concentrating technology is considered in dynamics, its change is determined by the task of making the company operation profitable. Technological indicators are secondary relative to financial and economical indexes. At the same time, technological and economical indexes are determined in their interrelation with ecological parameters. The elaborated model allows us to estimate all necessary economic, financial and technological indexes in their interrelation both for the company as a whole and as separately redistributed estimating the basic prognostication documents - accounting balance-sheet, profit and loss report, as well as the funds flow statement. When varying the managing parameters, all necessary result-producing financial and economical indexes are estimated and a need in and a possibility of an external funding by various sources are considered.The implementation of the model enables one to determine the required scale of production capacity, as well as the amount of raw-material resources needed. In case of shortages of the latter, there should be considered various scenarios of the production capacity enhancement or the possibility of commissioning of new sites or deposits and introduction of improved technologies."

Jan 1, 2003

By B Vorster

Falls of Ground is one of the highest causes of incidents, accidents and fatal injuries in our mines today. These falls of ground may occur as soon as the face is exposed after blasting or after machine cutting. The falls of ground can also occur after support has been installed. There are many reasons why these falls occur before and after supporting of the face. It is therefore important to support the exposed face as soon as possible to prevent the falls of ground. It is also very important to support the face with the correct support products and to support the face as designed and required by the mining engineers. The possible reasons for falls of ground, possible support methods and the products available will be discussed in this presentation. In typical conventional narrow vein stoping operations, the use of conventional temporary support components to offer some support to workers, whilst the permanent and generally more elaborate support system gets installed or constructed, still results in injuries to people. The author wishes to discuss the following items in this paper:- ? Introduction ? Basic face behaviour after exposure ? Controllable Parameters ? Mining Engineers support designs ? Primary and Secondary Support ? Products available for prevention of falls of ground

Jan 1, 2008

By Robert Lee, Jeff Corace, Rob Cyr

Blasting in the heart of the historic Byward Market District of Canada’s capital, Ottawa, presents a unique set of challenges. The obvious difficulties arising on projects requiring blasting within 3 m (10 ft) of 125 year old buildings in various states of disrepair have been encountered and successfully dealt with countless times before. The complexities increase exponentially when tenuous property boundaries, unknown structural details, litigious histories and the need for encroachment agreements lead to individuals with competing interests all able to impact the same operation. Blasting on three projects in the Market was started in early 2005 after months of negotiation. Ultimately, the potential for the projects to proceed hinged on the ability to successfully disseminate blast data to the various stakeholders. As part of the agreements drawn up, property owners demanded immediate notification of the measured vibration levels with contract provisions including clauses such that any exceedance of the USBM criteria immediately triggered project shut down and complete blasting program redesign, and approval by all parties. With stakeholders located in various cities and, in some instances, on various continents, a conventional attended monitoring strategy would not satisfy the requirements. In response to the critical reporting need, Explotech Engineering Ltd. installed unattended monitoring stations around the sites, all incorporating wireless telemetry. After each blast, data was automatically transferred from the monitoring stations to a web-linked server via the wireless network, where it was immediately available to project stakeholders through a password protected website. The solution required a unique blend of data acquisition, telemetry, database, and security technologies, all married to produce a reliable system that was easy to maintain and use. While these types of systems were originally developed for use as permanent monitoring networks in operating mines and quarries, monitoring professionals are increasingly benefiting from the technology on temporary building projects that have typically been the realm of attended monitoring strategies. Globally, this has emerged as a solution to provide more timely access to data for stakeholders, and to minimize the legal exposure from multiple violations of vibration limits. As this trend is likely to continue, the regulated vibration control industry is likely to see a continued shift in technology development to leverage wireless networks and the Internet to continue to improve data transfer, archiving and distribution.

Jan 1, 2006

By J. B. Newsom

IN the September 1936 issue of MINING AND METALLURGY the pioneer work of boring a 5-ft. shaft to a depth of 1125 ft. at the Idaho Maryland mine in California was described. Later, a Bureau of Mines Information Circular (No. 6923) gave additional data. In re¬cent months still further progress has been made in this technique through the sinking of a 5 1/2-ft. shaft for Pickands, Mather & Co. at their Zenith mine, Ely, Minn. The present work was done with new carefully designed equipment and several experienced men so that progress, as shown below has been much better:

Jan 1, 1938

By Stump NW

Until a year ago all isotope on-stream analysis utilised flow cells similar to those designed for conventional X-ray on-stream analysis. These systems incorporated a fairly complex sampling system necessary to present a representa- tive air-free sample of the main process to the flow cell. Maintenance costs and capital costs associated with flow cells and sampling systems have been generally high. Costs can be greatly reduced and reliability greatly increased, by using isotopes incorporated in immersible on-stream analysis probes which actually dip into the main process stream eliminating the need for sampling. A bonus of other advantages associated with immersible probes includes temperature stability and ease of calibration. This paper discusses details and results of the probe systems, justifica- tion for installing on-stream analysis, comparison of conventional X-ray and isotope techniques, and a brief survey of methods of analysis using radio- isotopes in on-stream elemental determinations.

Jan 1, 1971

By T. G. Melkus

A Setaram C-80 heat flux micro- calorimeter was used to study the surface and interfacial properties of fine coal particles in water containing flotation agents via heat of immersion measurements. Heat of immersion (?Himm) is usually a small exothermic quantity and can be used' to characterize a solid in terms of its relative hydrophobicity or hydrophilicity. The effects of coal type, surface oxidation, mineral matter content, kerosene concentration, and pH on the wetting characteristics were investigated. Results obtained from the calorimetry experiments correlated well with results from independent flotation experiments.

Jan 1, 1987

By B. M. Eiter, J. Hrica, D. R. Willmer

"Mineworkers are routinely tasked with making critically important decisions about whether or not a hazard presents an imminent danger. Researchers from the U.S. National Institute for Occupational Safety and Health collected formative data to investigate mine safety professional perspectives on workplace examinations, which revealed a potential gap in how mineworkers are assessing risk. During interviews, participants revealed not having a systematic methodology for mineworkers to use to determine if a hazard is considered imminent danger. In this paper, we identify and describe three distinct categories of imminent danger complexity and discuss potential steps that could lead to improved identification of imminent danger situations. Finally, we identify potential practices to incorporate into risk management efforts, including feedback, communication and specialized training, to increase awareness of imminent danger situations. IntroductionIn recent years, the metal and nonmetal mining sector, as categorized by the U.S. Mine Safety and Health Administration (MSHA), experienced an increase in the number of fatalities occurring at mine sites. From 2013 to 2015, 69 mineworkers were fatally injured, twice the number of fatalities in each of the previous two years (MSHA, 2015a). As a way to address this increase, MSHA issued its P15- IV-01 program policy letter, suggesting that “miners would benefit from rigorous workplace examinations conducted by experienced and trained examiners” (MSHA, 2015b). The goal of these examinations is to find hazards in the field and mitigate them before they cause injury or death to mineworkers. While it is important to identify all hazards in the workplace, it is critically important to identify those hazards that are considered imminent danger because they require an immediate response to avoid a severe or even fatal injury."

Jan 9, 2018

By B. M. Eiter, J. Hrica, D. R. Willmer

"Mineworkers are routinely tasked with making critically important decisions about whether or not a hazard presents an imminent danger. Researchers from the National Institute for Occupational Safety and Health (NIOSH) collected formative data to investigate mine safety professional perspectives on workplace examinations, which revealed a potential gap in how mineworkers are assessing risk. During interviews, participants indicated having processes in place for what should be done once an imminent danger situation is identified. Critically, however, they report having no systematic methodology for mineworkers to use to determine if a hazard is considered imminent danger. While this is important for all imminent danger situations (e.g., failure to lockout/tagout), it is especially important for those situations that are not immediately recognizable as imminent danger. In this paper, we identify and describe, three distinct categories of imminent danger complexity and discuss potential steps that could lead to improved identification of imminent danger situations. Finally, we identify potential practices to incorporate into risk management efforts, including feedback, communication, and specialized training to increase awareness of imminent danger situations. INTRODUCTION In recent years, the metal and nonmetal (M/NM) mining sector, as categorized by MSHA, experienced an increase in the number of fatalities occurring at mine sites. From 2013 to 2015, 69 mineworkers were fatally injured; that is twice the number of fatalities that occurred in each of the previous two years (MSHA, 2015a). As a way to address this increase, the Mine Safety and Health Administration (MSHA) issued a program policy letter (P15-IV-01) suggesting that “miners would benefit from rigorous workplace examinations conducted by experienced and trained examiners (MSHA 2015b).” The goal of workplace examinations is to find hazards in the field and mitigate them before they cause injury or death to mineworkers. While it is important to identify all hazards in the workplace, it is critically important to identify those hazards that are considered imminent danger because they require an immediate response to avoid a severe or even fatal injury."

Jan 1, 2018

The last decade of national water reform implementation has improved the availability and efficiency of water source allocation in Western Australia. However, it is critical to recognise that the concurrent mining boom witnessed the approach of full water allocation limits, and increasing trends in mineral processing, water infrastructure costs, and wastewater management costs. Water supplies are commonly viewed as absolutely critical to project feasibility in mining, industrial and energy generation projects, even if considered 'non-core business'.   An increasing density of mining projects and industrial estates in Western Australia (WA) creates an opportunity for water infrastructure cost sharing and synergies. The WA government and its agencies have given preliminary consideration to the establishment of independent water utilities in the goldfields (Kalgoorlie), the Pilbara, and Collie regions, and in the Kwinana Industrial Area. The impending Oakajee industrial area and Mid West regional development, and Anketell port in the East Pilbara, could also be considered for common non-municipal water supplies.   The critical issue of apparent commercial risk due to the large scale of water demands and the low customer numbers in the minerals sector relative to other water markets is expected to mandate government partnership in any non-municipal water utility ownership. The commercial feasibility risk is observed as a risk to water supply security for potential mining and industrial customers. Absence of proper water infrastructure planning and governance has the potential to create infrastructure access issues as observed for Pilbara rail developments under the Trade Practices Act 1974.   Other aspects of water cycle management which could be addressed by a non-municipal utility include resumption of mine dewatering water (required changes to WA legislation that are progressing) and consolidated wastewater management for maximising synergy or reuse opportunities and minimising cumulative environmental impacts.   Address of water infrastructure planning for non-municipal water demands must cover commercial and environmental sustainability outcomes to successfully progress minerals sector growth in the State.

Jun 1, 2010