Search Documents

By K. C. Ko, M. D. Bunnell

The studied coal mi1e is an underground coal mine located in the northern Wasatch Plateau of central Utah (Figure 1) . Since operation began in 1981, in situ stress conditions have been encountered which differ from the assumed conditions utilized during early mine design efforts. Geologic structures also varied somewhat from those projected during initial geologic interpretations of the area. The encountered geologic conditions combined with the unusual stress conditions prompted a combined study of in situ stress and stress-related geologic structures. The study was conducted in two phases, with phase 1 consisting of detailed underground mapping and analysis of stress-related geologic structures to determine stress orientations from which they originated; and phase 2, consisting of over- coring two sites within the mine to determine present in situ stress orientations and magnitudes. GEOLOGIC ANALYSIS Three types of geologic structures have been encountered in the mine that act as indicators of stress orientations of the geologic past. Two of these structures, faulting, and igneous dikes, are directly measurable in the mine. A third type of structure, photolineation, was detected through remote sensing methods and shoe god correlation to roof conditions in certain areas of the mine. Faults Two major orientations of faulting have been encountered in the studied coal mine, including a system of N 80 W striking normal faults and a system of N 55 to 70 W striking oblique-slip faults. Only data collected from the oblique-slip faults were used for this study due to the fact that these faults offset the N 80 W faults wherever the two systems intersect, indicating that the N 55 to 70 W system was created by a more recent stress field. Figure 2 shows locations within the mine where data were collected from seven locations along oblique-slip faults. Data collection consisted of measurement of fault plane strike and dip, fault slickenside trend and plunge, and slip direction. The data are tabulated in Table 1. The fault data were then plotted on stereo nets to determine the stress orientations present at the td of faulting (Figure 3). The determined stress orientations are 32~0 included in Table 1. The stereo net plots show average principal stress orientations of: 1) [ ] plunge 1 degree. These data suggest that the N 55 to 70 W oblique-slip faults were produced by a nearly

Jan 1, 1986

By Jeffrey Johnson, Thomas Brady, Radford Langston, Mary MacLaughlin, Hendrik Kirsten

The magnitudes and directions of in situ stresses affect the stability of mine openings, as well as the type and amount of ground support needed to maintain a safe working environment for miners. Using hollow inclusion stress cells, researchers from the Spokane Research Laboratory of the National Institute for Occupational Safety and Health obtained two in situ stress measurements from the face of two footwall lateral drifts at the Stillwater Mine near Nye, MT. The first measurement, obtained in 1997, was collected under the valley beneath the Stillwater River. The second measurement was obtained in 2002 under the main frontal massif of the Bear tooth Mountains in the western sector of the mine. Although few data are available, the major principal stress under the valley has been recorded as nearly horizontal in a north-south direction perpendicular to the ore body, while beneath the mountains, stress runs east-west parallel to the ore body. This paper documents the measurements, describes the in situ stress state, and discusses a finite-difference analysis of the biaxial test.

By Weiren Lin

The Mw 9.0 Tohoku-Oki, Japan earthquake occurred on 11 March 2011 produced a maximum coseismic slip of >50 m near the Japan Trench. To investigate why the plate boundary fault between the subducting Pacific Plate and overriding North American Plate which caused the earthquake had such unprecedented large coseismic displacement and slipped to the trench, Integrated Ocean Drilling Program Expedition 343 called Japan Trench Fast Drilling Project (JFAST) drilled three boreholes at Site C0019 through the earthquake fault about one year after the earthquake. Borehole C0019B dedicated to loggingwhile- drilling (LWD) penetrated ~850 meters below seafloor (mbsf) at a water depth of approximately 6890 m. The plate boundary fault is located at ~820 mbsf in the borehole and has been identified as the slip zone during the Tohoku-Oki earthquake. Borehole wall resistivity images obtained from LWD show that drilling induced borehole breakouts are available in a wide depth range above the fault but are not available below the fault. Breakouts are reliable indicators of the orientations of current maximum and minimum horizontal stresses and can also be used to constrain the horizontal maximum and minimum stress magnitudes. As results of breakout analyses, the maximum horizontal stress orientation highly varied in the upper part of the borehole, but has a clear preferred orientation in a northwest – southeast direction in the deeper part just above the fault. This orientation is approximately parallel to the direction of the Pacific Plate subduction. Stress magnitude constraints indicate that the post-earthquake stress states in the hanging wall are either in or close to the normal faulting stress regime. By inferring the pre-earthquake stress state and comparing with the constrained post-earthquake stress state, a significant coseismic stress change was interpreted. The stress change suggests an active slip of the frontal plate-interface consistent with coseismic fault weakening and a nearly total stress drop.

Jan 1, 2015

By G Baird, M Seto

A low-cost methodology that allows the determination of in situ stresses using oriented core specimens has been investigated. The technique can be used to determine the stresses during the early stages of a project, even in undeveloped areas of a mine. The research aim was to compare the experimental results estimated by the Acoustic Emission and Deformation Rate Analysis methods with those estimated by conventional Hollow Inclusion cell measurements. The studies have been focused on full stress tensor determination from a single oriented rock core. In all cases the rock core specimens recollected the in situ stresses reasonably well compared with the standard overcoring method.

Jan 1, 2000

The safety of mining operations is significantly influenced by the in situ stress fields in which the mining excavations are created. From the point of view of planning of mining operations, the in situ stress field is a most important input parameter for valid modelling of excavations. Many in situ stress measurements have been carried out for mining and civil engineering projects in southern Africa over the past 30 to 40 years. A database of in situ stress measurement results and observations has been compiled. This paper presents results extracted from the database which are considered to be of particular interest to mining areas in South Africa. The database will permit the estimation of likely stress conditions in new areas of mining, provide a basis for evaluation of results from future in situ stress measurement programmes, provide a basis for comparison of observed behaviour with expected behaviour, and provide a source of data on which realistic design and layout analyses can be based. The information contained in the database indicates that horizontal to vertical stress ratios in the Carletonville, Klerksdorp and Rustenburg areas are significantly higher than the value of 0,5which is commonly used in mine layout planning.

Jan 1, 1998

By B. Tiryaki

Longwall shearers usually suffer from excessive pick and pickholder consumptions and severe wear of the back plate of the clearance ring section of shearer drums. In practice, most of the drums were seen to be withdrawn from the face due to the abovementioned problems, while vane picks and their holders were intact due to the improper lacing design of the clearance ring picks. However, few underground investigations and their results on the effect of lacing arrangement of clearance picks on the service life of shearer drums have been published. Nevertheless, the pick consumption characteristics of shearer drums were not investigated in detail, since these are fewer pick consumptions with shearers when compared to roadheaders. This paper is concerned with the comprehensive in situ trials on the effect of lacing of clearance ring picks on the lifespan of shearer drums, and the pick consumption characteristics of longwall shearers at Cayirhan Coal Mine in Turkey. The lifespan of shearer drums employed with shearers in this mine increased 70 per cent, while the consumption rate of clearance ring picks decreased threefold through using an alternative lacing for clearance picks, indicating the significance of utilizing proper design techniques for clearance ring picks for the service life of shearer drums. Statistical analyses carried out, using the raw pick consumption data, implied that the clearance ring picks experienced much higher loads than vane picks, revealing that special attention must be paid to designing clearance ring picks. An average maximum consumption value of 41 was determined for clearance ring picks, with corner-cutting picks having the most replacements, while it was 35 for vane picks, on three-day based pick replacements.

Jan 1, 2004

By R W. Henley, L Knuefing, M Turner, Y Zhang, M Saadatfar, A Limaye, R Cruikshank, M A. Knackstedt, A Kingston, L Beeching, N Francois

A better understanding of ore fragmentation and the textural features of ore is a key to the energy efficient extraction of targeted minerals from low-grade ore deposits. In this study, X-ray microcomputed tomography (micro-CT) is employed to study mineral liberation during the tensile failure and onset of fragmentation of a copper ore. Our results show that X-ray micro-CT could inform new studies of ore micromechanics and fragmentation at the laboratory scale and may offer new avenues to address current challenges in the design of efficient comminution processes. We present the results of experiments based on a high-pressure apparatus enabling micromechanical studies to be carried out in situ (inside a micro-CT scanner). This platform produces high-quality 3D images of the evolution of a sample of porphyry copper ore during an in situ fragmentation test. A sequence of tomographic images enables mapping in 3D of both the deformation of mineral phases and the fragmentation process. The fragmentation occurs quasistatically through multiple stages starting with an initial tensile fracture splitting the ore diametrically, followed by tensile-activated nucleation and growth of multiple fractures producing a complex fracture network. Coupling breakage with microstructural information enables quantitative determination of the impact of ore texture heterogeneity on fracture patterns and mineral liberation. This microstructural information can be compared to key measurements of the ore mechanical behaviour such as the global deformation energy, strain deformation field and the stress relaxation response. The latter allows one to identify interesting precursor signals of the tensile failure. The copper liberation, fragment size distribution and breakage patterns are statistically characterised and related to comminution mechanisms which are clearly identified in the sequence of tomographic images. The two dominant mechanisms are rock-rock friction/compression induced by fracture closing and compression-driven fragmentation at rock-crusher contact points.

Aug 24, 2022

By K. U. Kainer, A. Stark, D. Tolnai, M. Hehenberger, C. L. Mendis, N. Schell, N. Hort

Samples of an as extruded Mg-6Zn-0.6Zr-0.4Ag-0.2-Ca (wt.%) alloy was compressed at room temperature and at 250°C. The in situ deformation tests were performed at the P07 (HEMS) beamline of PETRA III, DESY, with a modified DIL 805 A/D dilatometer with to Kapton windows on the sides and the induction coil opened for the beam to transmit the sample. The deformation rate was 10-3 s-1 the samples were deformed to failure. The diffraction patterns were recorded every 3 s with a Perkin Elmer 1621 Flat Panel Detector. The results reveal that different deformation mechanisms are activated during compression at a given strain value. At room temperature twinning is the dominant deformation mechanism, while at elevated temperature dynamic recrystallization occurs while the contribution of twinning to deformation is significantly reduced. The compressed samples were further investigated with conventional metallography and SEM-EBSD to determine the volume fraction, the type of twinning and the strain retained within the grains. The parallel testing of pure Mg samples under the same conditions allows comparison of the compression behaviour of the ZKQX alloy with Mg.

Jan 1, 2014

By Napisporn Memongkol

Syntheses of Al-TiC-Al2O3 and Al-SiC-Al2O3 composites were obtained in situ by carbothermal reduction of mixtures of Al powder, TiO2 powder and activated carbon powders and Al powder, SiO2 powder and activated carbon powders. The reductions were carried out in a horizontal tube furnace under flow of inert gas. The standard Gibbs energy minimization method was used to calculate the equilibrium composition of the reacting species. The synthesized products were mixtures of aluminum reinforce with titanium carbide and alumina and aluminum reinforce with silicon carbide and alumina. The effect of the reaction temperature (1000 o C ? 1200 o C) and condition of precursors on the Al powder, TiO2 powder and activated carbon powders and Al powder, SiO2 powder and activated carbon powders were investigated using XRD and SEM method. The synthesized products showed those composites with aluminum matrix and titanium carbide and alumina as reinforced phases and aluminum matrix and silicon carbide and alumina as a reinforced phase was formed.

Jan 1, 2006

By Sutham Niyomwas

Silicon-Silicon Carbide (Si-SiC) composites were synthesized by self-propagating high temperature synthesis (SHS) from a powder mixture of SiO2-C-Mg. The reaction was carried out in a SHS reactor under static argon gas at a pressure of 0.5 MPa. The standard Gibbs energy minimization method was used to calculate the equilibrium composition of the reacting species. The effects of silica sources and carbon mole ratio in precursor mixture on the Si-SiC conversion were investigated using X-ray diffraction and scanning electron microscope technique. The as-synthesized products of Si-SiC-MgO powders were leached with 0.1M HCl acid solution to obtain the Si-SiC composite powders.

Jan 1, 2009

By Malcolm Scoble, Jean-Marc Robert, Luciano Piciacchia

"An approach to the in situ testing of mine backfills is outlined. It has been developed to provide a measure of the effective strength and stiffness of such materials after placement in stopes. This paper is based upon recent field studies undertaken at five Quebec mines. Details of the selected instrumentation, supporting equipment and testing procedures are reviewed. The mechanical behaviour of the backfills is reported and related to their physical properties. This approach represents an economical, simple and reliable means to assess the mechanical characteristics of backfill materials as an aid to both mine design and placement quality control. IntroductionDevelopments in backfill and mining method technology are creating a pressing need to develop effective techniques for characterizing the physical and mechanical properties of backfill in situ, rather than relying on traditional laboratory testing. The development of bulk mining methods is creating the requirement to more fully understand the nature of exposed fill faces to design for stability in pillar recovery operations. Other backfill technological developments currently receiving widespread attention are high density placement and the use of alternative additives to Portland cement. In Canada, U.S.A. and South Africa attention is also being placed on employing backfill to alleviate rockburst hazards(1,2.3l. In situ testing offers the potential to measure the geomechanical properties of backfill once placed in stopes , in order to assess its actual role in pillar recovery and ground support. Similarly, it offers the ability to provide some quality control during backfill placement. This role is seen as becoming increasingly important with the growing recognition of the need to pay greater attention to the mode of placement, which governs segregation and variation in the properties actually achieved by the backfill after placement."

Jan 1, 1987

By D. E. Munson

To assure the safety of a radioactive-waste repository, the performance of the repository must be predicted far into the future. The Waste Isolation Pilot Plant (WIPP) Program is responsible for developing the technology for such performance predictions in bedded salt. An important technology-development activity concerns the, fielding of very large-scale in situ tests to determine the time-dependent deformation of underground openings in salt as a basis for validation of the predictive technology. This technology is necessary to predict repository seal performance and final closure times of rooms and may be of value to the salt and potash mining community, as well.

Jan 1, 1992

By D. E. Munson

The Waste Isolation Pilot Plant (WIPP) Project was established in 1975 by the Department of Energy (DOE) under Public Law 193 to develop the necessary technology for safe disposal of radioactive wastes from the defense programs of the U.S. The technology development involves extensive theoretical, numerical, and laboratory programs, as well as construction of the WIPP facility in southeastern New Mexico for in situ testing and waste storage demonstration. If after the demonstration, the facility is found to comply with regulations of the Environmental Protection Agency, then the facility will become a repository for Transuranic (TRU) waste. The underground portion of the facility is 655 m beneath the ground surface in massive natural salt deposits of the Salado formation, as shown in Figure 1.

Jan 1, 1991

By M I. Pownceby, N A. S Webster, A J. Studer, I C. Madsen, J A. Kimpton, M J. Fisher-White, L Lu

In situ synchrotron X-ray and in situ neutron diffraction-based experimentation have been implemented to characterise the formation of the complex calcium ferrite iron ore sinter bonding phases silico-ferrite of calcium and aluminium (SFCA) and SFCA-I. Experiments were carried out using fine-grained (<20 ¦m) sinter mixtures containing ~77 wt per cent Fe2O3, 14 wt per cent CaO, 3.5 wt per cent SiO2 and 5 wt per cent Al2O3, with diffraction data collected during heating until 1300 - 1350¦C, which was enough to ensure complete melting of the SFCA phases. In the case of the in situ synchrotron experimentation, results showed that altering the nature of the starting sinter mixture (ie substitution of goethite for hematite; substitution of an amorphous Al2O3-based mineral for gibbsite) did not have a significant effect on the thermal stability range of the SFCA phases. It did, however, have a profound effect on the formation and rate of consumption of the calcium-rich ferrite phases C2F and CF, and on the formation mechanisms of SFCA and SFCA-I. The in situ neutron diffraction experimentation is the first described in the context of iron ore sintering, and the observation of both SFCA-I and SFCA formation in the in situ diffraction data represents the first step in achieving the goal of charactering iron ore sinter phase formation in large volumes of industrial sinter starting materials with a wide range of particle sizes (up to 6.3 mm).CITATION:Webster, N A S, Pownceby, M I, Madsen, I C, Studer, A J, Lu, L, Manuel, J R, Kimpton, J A and Fisher-White, M J, 2013. In situ x-ray and neutron diffraction studies of silico-ferrite of calcium and aluminium iron ore sinter phase formation, in Proceedings Iron Ore 2013 , pp 487-494 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By Desiree Willis

At 6 percent downgrade to a low point beneath California?s Sacramento River, the Lower Northwest Interceptor Sewer was a difficult project from the outset. Project owner Sacramento County Regional Sanitation District (SRC-SD) planned to excavate the V-shaped tunnel in two sections using an earth pressure balance (EPB) machine in soft ground. Muck removal, due to the steep downgrade, was a tricky proposition. ?We did look at muck cars, but determined they were not the best option due to the relatively steep slope of the tunnel alignment. The safety benefits of conveyors on this job were obvious, as there were not the potential hazards associated with muck cars traveling on an incline or derailing,? said Steve Norris, senior civil engineer for SRCSD The successful project represented one of the first instances of a conveyor system being used for a soft ground tunnel boring machine (TBM) application. Several projects in California, including a recent tunnel completed in 2009, have highlighted a growing acceptance of conveyor muck removal in a variety of ground conditions. Conveyors offer higher system availability than more common methods, such as muck cars, as they allow for continual operation of the TBM. The design of conveyor systems must, however, take into account the differences in material between soft ground and hard rock, including belt cleaning features, sealed transfer points and other elements.

Jun 1, 2010

By A Kite

Frontline leaders play a critical role in the safe and productive operations of Australia’s mining, resources and heavy industries. These leaders set the workplace culture, especially during night shifts and weekends, by providing team direction and encouragement, providing access to resources, fulfilling statutory requirements, enacting and reinforcing risk management systems, setting the standards on shift and acting as the primary conduit of communications between senior leaders and team members.

May 5, 2022

By J. F. Allan

The main conditions which affect investment in mineral exploration and development are compared in five countries currently considered attractive for mineral investment - Canada, the U.S., Australia, Brazil and the Philippines. The primary parameters - the probability of occurrence and discovery of mineral deposits and the short and long term viability of mineral development - are evaluated and compared on a relative basis by a form of factor analysis. This analysis indicates that of the five countries studied, Canada is second only to the United States in degree of favourability for mineral exploration and development.

Jan 1, 1976

By Robert L. Bates

On April 2 and 3, 1970, more than 100 geologists attended the Sixth Annual Forum on Geology of Industrial Minerals at Ann Arbor, Mich. After this brief appearance, the Forum apparently ceased to exist- but it didn't really, and another spring will see it again in action, in another corner of the country. The organization might be characterized as the country's largest permanent floating conference on the geology of industrial minerals. What is the Forum, where did it come from, and what is it up to? The idea originated in 1964 with a small group in the Department of Geology at Ohio State University, Columbus. This group felt that a forum was needed for the exchange of geologic information on industrial rocks and minerals. They envisioned an approach-which has subsequently been adhered to--that would be dominated neither by geological academics interested in theoretical problems nor by practical engineers concerned with processing large tonnages of rock. It was proposed to focus attention on the middle part of the spectrum, especially on practical problems of geological occurrence and how these problems affect extraction and use. In terms of the standard rock-products flow sheet, which starts with a truck unloading into the primary crusher beneath the words 'from quarry,' it was proposed to focus geological attention on what is beyond the primary crusher, out in the quarry.

Jan 1, 1970

By Lawrence F. Rooney

One of Edgar Allan Poe's stories that haunts my subconscious is the Masque of the Red Death. These days, whenever I join a group like this, especially during the cocktail parties, I see myself and others as those mythical swingers seemingly isolated from the plague. The world, but this country especially, has had a ball plundering, spending, and wasting its natural resources for 100 years. And, as in days of yore, it is fitting that we end this ball with spectacular fireworks: trips to the moon, so that our grandchildren, huddled in their caves along the Ohio, will better understand how it all began.

Jan 1, 1970

By R. S. Shrode

By now most readers of this column are aware that it no longer has a regular editor. Tom Murphy, who did the job so well, has had to bow out because of his duties in Australia---duties that keep him from the luxuries of such things as typists and typewriters for rather extended periods of time. We will miss his regular contributions but hope and expect to hear from him as a guest columnist from time to time. Finding an editor to function on a regular basis turns out to be no simple task. This does not mean that there may not be candidates around who would secretly enjoy having their arm twisted into a "yes" position, but at the moment none has been found. Anyway, at the Salt Lake City business meeting it was agreed that we should try to spread the load around. To that end, the Regional Vice Chairmen were specifically singled out as one potential source of contributions. These fellows should have an opportunity for a hearing during their term in office. The existing organizational set-up of the IndMD Division may be a little unfair to this group of officers. The limited responsibility outlined in our Manual of Official Duties and Responsibilities does not offer them much chance for self-expression. Probably the by-laws were written so as to have a geographic representation of membership in case it should be needed at some time. But that is another subject. The point is that now these regional officers have an opportunity to speak out on topics of their own choosing through this column. Some have already done just that. There are also other potential contributors to the column. One is the Secretary, who twice a year uses the column for distributing the minutes of our business meeting to the members. Another is the outgoing Division Chairman. In Salt Lake City, it was decided that this officer should be challenged to contribute something each year as a means of reviewing events of the past year or explaining what should have happened but didn't. I am, therefore, trying to accept that challenge.

Jan 1, 1970