Search Documents

By Sertaç Dündar, Bilgehan Kekeç, Arif Emre Dursun, Niyazi Bilim

"Estimation of rock drillability is vital for mining and boring operations. For this purpose, many researchers have developed various models and equations to estimate rock drillability. Most of these models aim to determine the drillability of rock and the penetration rate by using the physical and mechanical properties of rocks. Although drillability primarily depends on rock properties, other parameters have an impact on drillability as well. One of these parameters is the rotation speed of the bit. This study investigates the effect of rotation speed of the bit on drilling performance. Drilling tests were performed in the laboratory using rotary core drilling and a diamond drilling machine. The relationships between the physical rock properties and the penetration rate were investigated on 15 different rock types and four different rotation speeds were applied to determine the effect of rotation speed of bit on drilling. The uniaxial compressive strength, density, and P wave velocity show strong correlations with the penetration rate. In addition, if the values of the physical and mechanical properties of the rock increase, the effect of the rotation speed on the penetration rate decreases, i.e., increasing the rotation speed of the bit slightly affects drillability on hard and solid formations. 1. Introduction Drilling is one of the most essential operations in the mining industry, beginning from the exploration phase and continuing throughout all stages of production to the end of mine life (Taheri et al. 2016). In addition, drilling is widely using in the construction industry and other engineering operations. Various drillholes (blastholes, injection holes, borehole, diamond wire holes in natural stone mines, etc.), are needed during development and production activities in underground and open-pit mines as well as in dam, tunnel, road construction and sewage systems. For effective drilling operations, it is first necessary to gather information about the formation to be drilled. Drilling should then be performed after selecting appropriate drilling equipment and drilling parameters (thrust, pressure, rotational speed, flushing). Prediction of the drillability of rocks is vital for planning and performing the drilling process. Although, drilling is affected by several factors, the most important ones are related to the geological and mechanical properties of formation (Protodyakonov 1963, Paone et al 1969, Tandanand and Unger 1975, Pathinkar and Misra 1976, Rabia 1985, Perrin et al 1977). Determining the penetration rate is vital for planning a project and calculating the operation costs. The prediction of drilling affects the selection of drilling equipment, the efficiency of drilling equipment, project costs and the process of drilling operations."

Jan 1, 2017

By C. Aldı, O. Yaral

For the more economical excavation of tunnels in underground mining activities, the selection of mechanised excavation machines (such as roadheaders, electro-hydraulic drills, etc.) and the analysis of performance prediction that can be used in estimating machine energy consumption have been subjects of research from past to present. One of the parameters to be considered in studies examining these methods, is the grinding process. The success of increasing efficiency in grinding is expressed by a reduction in energy consumption. The goal of a grinding process is to maximise the grinding amount at the appropriate grinding size while minimising the energy consumption per tonne of the fragmented material. Today, the depletion of high-grade ore deposits has largely directed the mining industry towards low-grade but large reserve ore deposits. This shift has particularly increased the importance of the grinding process, as it is dependent on particle liberation. Grinding is a critical step in reducing the mineral to the appropriate size, and energy consumption poses a significant challenge in this process. As a result, researchers have conducted various studies focusing on energy efficiency and cost optimisation in this field. In this study, the grindability of 7 different coal environment rocks (sandstone, siltstone) from the Zonguldak Basin, Uzulmez Region was investigated. For this, Hardgrove Grindability Index and Bond Work Index tests were conducted. While determining the relationships between grindability and other parameters, the results obtained from the Hardgrove Grindability Index (HGI) test were used. The energy values found in the Bond Work Index (BWI) test were used to evaluate the excavatability of the rocks. Additionally, tests for strength, hardness, drillability, and abrasiveness were conducted to observe the impact of other parameters on grindability. Considering the results obtained from the experiments, significant relationships were found between the grindability of the rocks and other parameters.

Mar 30, 2026

Investigation of the Effect of N-Substituents on Performance of Thioureas as Special Collectors for Copper Sulfides by ab Initio Calculations

Sep 13, 2010

By P. N. Anyalebechi

Keywords: Aluminum alloy 3004, Solidification rate, Homogenization, Second phase particles The effects of the fineness of as-solidified cast microstructure and temperature on the response of aluminum alloy 3004 to homogenization heat treatment (a.k.a. preheat) have been investigated. The study was conducted at 538oC and 595oC on directionally solidified laboratory-size ingots with a range of solidification rate of 0.10oC/s to 29.4oC/s. Optical and electron microscopy, quantitative image analysis, electrical conductivity, and electron probe microanalysis were used to quantify the effects of the homogenization heat treatment on the microstructure of aluminum alloy 3004. In general, increase in fineness of as-cast microstructure and homogenization temperature enhances the a-transformation reaction, dissolution of Mg2Si, elimination of dendritic microsegregation, and dispersoid formation. The homogenization heat treatment reduces the average size of second phase particles in castings solidified at <1oC/s. However, in castings solidified at above 1oC /s, homogenization causes the coarsening of the second phase particles. Mn in solid solution is independent of homogenization heat treatment temperature.

Jan 1, 2005

By H. Ipek

In this study the effects of interstitial ratios on k-feldspar samples were investigated. The k-feldspar samples were taken from Egypt using dry batch grinding conditions and a kinetic model. Three different mono size fractions (-3350+2360, -850+600 and -300+212 µm) were ground separately for 0.5, 1, 4, and 8 minutes and at four different interstitial ratios (125%, 100%, 75% and 50%) using a Bond mill with a mixture of five ball sizes. The mill used was at a size of 30.5 cm diameters, with 30.5 cm length, providing a total mill volume of 22272 cm3. The mill has a total mass consisting of 22648 g. steel ball mixtures of 38.10, 31.75, 25.40, 19.05 and 12.70mm diameters, occupying 22% of mill volume. The mill rotates at a speed of 70 rpm. The weights of the feed charges were 3000, 2000, 1000, and 500 g for 125%, 100%, 75% and 50% filling of the interstices of the balls respectively. The specific rate of breakage (Si) was determined from the top size fractions at different grinding times that were mentioned above and the model parameters were compared for the four different powder filling ratios (U). In many investigations, it has been found that an interstitial filling ratio of U = 0.6-1.1 is a good powder ball loading ratio to give an efficient breakage in a ball mill. In this study, it was found that U=1.25 is a good ratio for K-Feldspar.

Jan 1, 2006

By H. Karabulut, S. Gündüz, K. Karacif, M. A. Erden

The corrosion properties of iron-based composite materials containing graphite and silicon carbide (SiC) reinforcement were investigated. The effects of silicon carbide reinforcement were investigated by adding 0.5% graphite and 1%, 2%, and 4% SiC. A powder metallurgy method was used to produce the composite samples. Iron, graphite, and silicon carbide powders were blended for one hour with a threeaxis mixer and then unidirectionally pressed under a pressure of 750 MPa. After pressing, the composite materials were sintered at 1100°C for one hour. The corrosion properties and microstructure, density, and hardness properties of the composite materials that can affect the corrosion properties were also investigated. It was determined that the pore ratio and hardness of the composite material increased, and corrosion resistance decreased, with increasing silicon carbide content.

Jun 2, 2022

By P. N. Anyalebechi

"The effects of solidification rate, initial melt hydrogen concentration, and grain refining on porosity formation in aluminum alloy 2024 have been investigated with unidirectionally cooled laboratory-size ingots. The ingots were prepared from melts containing hydrogen concentration of 0.059-0.27 cm3/100 g and solidified at 0.2-37 °C/s. As expected, the amount of porosity, average pore size, and pore number density increased with increase in melt hydrogen concentration and decrease in solidification rate. However, the effect of solidification rate was greater at the very low melt hydrogen concentration (0.059 cm3/100 g). These results are consistent with reported effects of solidification rate and melt hydrogen content on porosity formation in other aluminum alloys. Interestingly, addition of grain refiner slightly increased the amount of porosity and the average pore size, especially at solidification rates above 1°C/s. IntroductionIn shaped castings and wrought products fabricated from ingots, billets, bars, or slabs of aluminum and its alloys porosity formation is a problem. This is because it compromises their tensile strength, fracture toughness, and fatigue properties [ 1-18]. The pores are usually the crack initiation and propagation sites [6,8,9] and the largest pores tend to dictate the fatigue life of the aluminum products [9,10,14]. Porous regions within an aluminum product probably yield first due to the reduced tensile load bearing capacity, causing the concentration of the strain near the voids which subsequently results in premature fracture. In aluminum alloy ingots, billets, bars and slabs porosity formation is particularly problematic because of its persistence through fabrication and potential for reappearance or exacerbation during subsequent thermal treatment processes before and/or after fabrication [19]. In fact, persistence of microporosity is a serious problem in large thick plates of wrought aluminum alloy products that must be rolled from correspondingly large direct-chill or electromagnetic cast ingots. Some of these thick plate products are machined into large aircraft components that are required in service to withstand multi-directional stresses and to possess high fatigue strength, fracture toughness, resistance to stress corrosion cracking, and strength in the short-transverse direction [1,20]."

Jan 1, 2011

By F. D. Ayhan

The aim of this study was to investigate the effects of various water mediums on desulfurization and deashing of a coal sample using flotation. For this purpose, experimental studies were conducted on a coal sample containing high ash and sulfur contents. The effects of pH, solid concentration, collector amount and frother amount on the flotation were investigated separately in Mediterranean Sea water, Çermik thermal spring water, snow water and tap water. Flotation results indicated that, when comparing the various water mediums, the following order for the ash content was obtained: snow water < Çermik thermal spring water < tap water < the Mediterranean Sea water. For the reduction of total sulfur, the following order was obtained: snow water > Çermik thermal spring water > Mediterranean Sea water > tap water. When snow water was used as a flotation medium, it was found that a concentrate containing 3.01% total sulfur and 27.64% ash with a total sulfur reduction of 57.06% was obtained from a feed containing 7.01% total sulfur and 41.17% ash.

Jan 1, 2009

By G. L. Mowrey

One critical element of the U.S. Bureau of Mines (Bureau) autonomous mining research program is the development of a reliable coal interface detection (CID) system. Several candidate CID concepts currently being investigated by the Bureau include vibration, passive infrared, radar, and natural gamma radiation (NGR). To establish which CID sensor technologies need to be developed for a given seam, coal and adjacent rock samples (i.e., immediate roof and floor) are being collected from selected major coal seams in the U.S. and are being analyzed in terms of NGR and other geophysical measurements. Results of the NGR measurements indicate that, in general, all shale and shale-like materials (e.g., drawslate, slate, and fireclay) have higher NGR readings than the coal seam. Consequently the NGR method appears to be a potentially useful CID tool, provided that the immediate roof and floor are both composed of a high percentage of shale-type material.

Jan 1, 1990

Ferruginous manganese deposits have been known at Ripon Hills since the late 1950s. The main group of deposits occur in an area 6 km by 5 km and these were extensively investigated by Longreach Metals N.L. during1971 and 1972 for possible commercial exploitation.Ripon Hills is a dissectcd fault plateau 350 m above sea level formed by the uplift of a block of gently dipping Proterozoic shales, cherts, and dolomite. The plateau consists of chert breccia which is underlain by massive dolomite. The shales which are ferruginous and manganiferous overlie the chert breccia but are now only preserved, in places, in the broad depression and valleys of the plateau.The ore deposits occur as supergene replacement of the shales and were investigated by geological mapping, grid percussion and diamond drilling, and bulk beneficiation testing. Iron and manganese oxides erraticallyreplace Shale accompanied by the leaching of other minerals. The ore is composed of fine grained pyrolusite intergrown with fine grained hematite and locally containing extensively altered bixbyite and braunite. Thegangue mineral is mainly kaolin.The average grade, using a 15 per cent Mn cutoff, was 19 4 per cent Mn and 25&#183;9 per cent Fe for a combined drill-proven, indicated, and inferred tonnage of 56,000,000 tonnes. The average depth of this mineralization from the surface is 11 m. Using a cutoff grade of 20 per cent Mn the average grade was 24&#183;6 per cent Mn and 23&#183;0 per cent Fe for a combined tonnage of 12,000,000 tonnes to an average depth of 8 m.The substantial drop in reserves occurs because a high proportion of the mineralized material contains less than 20 per cent Mn.It was shown that whereas the lower grade ore, despite erratic fluctuations in grade, could be beneficiated to specification grade by crushing, screening, and conductivity ore sorting, the higher grade ore could be beneficiatedto specification grade by crushing and screening only. The utilization of the higher grade ore was considered to constitute a more viable operation.There is potential for high grade manganese ore to be discovered in the Ripon Hills area at the contact of chert breccia and underlying dolomite.

Jan 1, 1977

By Leming Ou, Longsheng Yi, Qiming Feng, Yiping Lu, Qing Shi, Kun Liu, Guofan Zhang, Yanfei Chen

"Three important components of stirred tanks involved in energy consumption, the impellers and baffles, were investigated to intensify the agitation pretreatment on the flotation of nickel ores. Flotation tests revealed that the stirred tanks with two impellers had an advantage over those with one impeller in intensifying agitation pretreatment, and the higher agitation speed led to better flotation performance of nickel ores. Installation and removal of baffles were also employed in the stirred tanks, and flotation tests demonstrated that with baffles, the flotation grade increased significantly. These agitator design improvements were used to demonstrate that the energy supplied to the system significantly influences the flotation recovery and that if the energy consumption of the agitation pretreatment is ideal, flotation efficiency can be improved. Data from full-scale operations backed up these results.INTRODUCTIONThe flotation recovery of nickel-copper sulphide ore at the Western China nickel mine has historically been difficult due to the presence of large amounts of serpentine minerals (Feng, et al., 2012). Many studies reported that serpentine minerals tend to have a positive potential at pH values up to 9.5, while sulphides (such as pentlandite and chalcopyrite) have a low isoelectric point(Feng, et al., 2012). Serpentine minerals can form surface coatings on negatively charged sulphides surface due to electrostatic attraction when they interact with each other, which may also reduce collector adsorption and increase the hydrophilicity of the sulphide particles. In order to improve the flotation of nickel sulphides, sodium hexametaphosphate, sodium silicate, carboxymethyl cellulose (CMC), and other agents are used to disperse serpentine coating from sulphide surfaces in the flotation of the Jinchuan deposit and other nickel ores in China ( Kirjavainen and Heiskanen, 2007; Lu, et al., 2011). However, it is difficult to improve of the sulphide flotation due to the high dosage and the lack of selectivity."

Jan 1, 2018

By David Sainsbury, Bevan Thompson, Yuejun Cai

The practice of placing loose rockfill as passive support in open stoping voids, of narrow vein mineral deposits, lends itself to the sterilisation of substantial mining reserves in the requirement for regional crown/sill pillars. Significant benefits are to be gained by the Australian mining industry via the development of improved guidelines for the extraction of such sterilised mine pillars. The application of selectively injecting specifically developed ettringite (calcium sulphoaluminate hydrate) type cement grout into loose rockfill, enables an artificial pillar to stabilise the surrounding rockmass and prevent the caving of loose rockfill from the previously backfilled void during extraction of remnant crowdsill pillars. This paper presents the results of laboratory testing used to reduce the technical risks associated with the design of cemented rockfill pillars. A laboratory testing program was devised to investigate the critical parameters influencing the performance of a stabilised rockfill matrix, along with the critical parameters influencing the interpretation of laboratory test samples. The factors investigated include; sample size and shape, particle size distribution, curing time, water quality, cement : water ratio and the confinement effect.

Jan 1, 2001

By J. Whitford

The established crown pillar extraction method at Gold Fields Australia Ltd.’s Crusader Mine, leads to the significant dilution and poor recovery of ore due to caving of the overlying loose rockfill. The application of selectively injecting specifically developed ‘FB200’ ettringite (calcium sulphoaluminate hydrate) type cement grout into loose rockfill to form a stabilised rockfill material, enables an artificial crown pillar to stabilise the surrounding rock mass and prevent caving of the overlying loose rockfill during crown pillar extraction. Investigation of the geomechanical criteria for crown pillar extraction beneath stabilised rockfill has enabled the safe and efficient extraction of two crown pillars at the Crusader Mine. La méthode actuelle d&apos;extraction des piliers horizontaux à la mine Crusader dont la propriétaire est le Goldfields Australia Ltd amène à une dilution sensible du minerai, à cause de l&apos;effondrement du remblai peu compacté qui se trouve au-dessus. Par moyen d&apos;injection sélective du coulis de ciment FB200 ettringite (sulfoaluminate de calcium hydraté) qui a été développé spécifiquement pour cette application, un pilier artificiel est crée et celui-ci empêche l&apos;effondrement du remblai pendant l&apos;extraction du pilier de minerai au-dessous. A la suite des études géotechniques de la méthode, deux piliers horizontaux à la mine Crusader ont été extraites, de manière efficace et sûr. Die feststehende Krone Pfeiler Extraktionsmethode beim Crusader Mine von Gold Fields Australien GmbH, führt wegen caving des overlying lockerer rockfill zur bedeutungsvollen Verdünnung und schlechtem Wiederfinden des Erzes. Der Antrag, ausdrücklich entwickelten &apos;FB200&apos; ettringite selektiv zu spritzen, (Kalzium-sulphoaluminate-Hydrat) Art kittet Mörtelschlamm in lockeren rockfill, um ein stabilisiertes rockfill-Material zu bilden, ermöglicht einem künstlichen Kronenpfeiler, die umliegende Steinmasse zu stabilisieren und caving des overlying während des Kronenpfeilerherausziehens lockeren rockfill zu verhindern. Untersuchung der geomechanical-Kriterien für Kronenpfeilerherausziehen unter stabilisiertem rockfill hat dem sicheren und tüchtigen Herausziehen von zwei Kronenpfeilern beim Crusader Mine ermöglicht.

Jan 1, 2003

By G. Gauvin

Life span of aluminum smelting electrolysis cells can reach up to 3000 days. During this period, cathode blocks go under various physical and chemical changes that could result in an increase of electrical resistivity. The increase may be due to carbon migration from the cast iron to the steel bars, gap evolution between the cathode block and the cast iron, cathode cracking, etc. This paper focuses however only on the collector steel bar electrical resistivity evolution. To reveal the main phenomena responsible for the electrical resistivity increase, chemical analysis, metallographic and electrical resistivity tests were conducted on two steels bars picked from two Hall-Héroult cells after autopsies. Cathode voltage drop and temperature were measured using electrically insulated internal probes and thermocouples on 16 samples from each steel bar. Electrical resistivity can reach up to 1.21µO-m for a steel bar aged 2505 days compare to 0.142µO-m for steel AISI 1008 at room temperature.

Jan 1, 2011

By J. DuCarme, A. Smith, M. Reyes

"A magnetic proximity detection system is mounted on a mobile mining machine to prevent underground workers from being pinned or struck by machine motion. The system generates magnetic fields around the machine to determine safe working distances. The minerworn component measures the magnetic field in order to approximate location. Large masses of steel, such as those from mining equipment, can alter the magnetic field distribution. This affects the locational accuracy of the system, thus adversely impacting worker safety. To examine this problem, U.S. National Institute for Occupational Safety and Health researchers developed a method and test system to study the influence of a steel mass on the magnetic field distribution. The results show that a steel plate can strengthen the magnetic field perpendicular to the generator by up to 40 percent. Furthermore, they show that the degree of the influence on the field distribution is a function of distance. The results from this study can be used to further develop and improve the performance and reliability of electromagnetic proximity detection systems used in underground mining applications.IntroductionOn average, 250 miners are injured every year, and 43 miners were reported to be killed by striking or pinning accidents involving continuous mining machines in the United States between 1984 and 2015, according to the U.S. Mine Safety and Health Administration (MSHA, 2015). Continuous mining machines are large mobile machines used to mechanically cut coal in underground mines. These machines weigh approximately 60 t (132,000 lb) each. Although modern continuous mining machines can be remotely controlled, operators still need to be close to the machine primarily because of the low visibility and wide blind spots of the underground working environment.The MSHA promulgated a final regulation in 2015 that requires the use of proximity detection systems on all continuous mining machines except fullface machines. MSHA has approved five such systems to be intrinsically safe for use in underground coal mines: (1) Strata Worldwide’s HazardAvert System, (2) Frederick Mining’s Model 200 HazardAvert Detection System, (3) Nautilus International’s Coal-Buddy System, (4) Matrix Design Group’s M3- 1000/Joy Global SmartZone Gen 1 and (5) Matrix Design Group’s IntelliZone/ Joy Global SmartZone Gen 2."

Jan 6, 2018

By S. Kwon

When an underground excavation is created near to an instrumented measuring location, deformation at the location increases. The characteristics of this deformation increase, as well as the duration of the influence caused by the adjacent excavation, is dependent on parameters such as opening geometry and measuring location. In this study, neural networks were applied to investigate the deformation increase and the influence of each parameter on the deformation change derived from extensometer measurements at the Waste Isolation Pilot Plant (WIPP) site in New Mexico, USA.

Jan 1, 1998

By Andrzej Walentek

In polish coal mining due to specificity of seams lying the multiple extraction is used. In this kind of mining, it is essential to take into account all geological and mining conditions which have an influence on stability and functionality of workings during their using. In view of above, for one of polish coalmines, by mean of Phase2 program, the numerical calculation were made for assessment of the influence of advancing excavation front on convergence of roadway located 30 meters above longwall was analysed. In order to verify developed prognosis, in analyzed roadway the underground investigations in scope of convergence measurement and changes of load exerted on working support were carried. As a result of these investigations it was found that real convergence on certain part of roadway was significantly larger then determined in prognosis. Additional calculations and analysis showed that the main cause of differences was underestimation of influence of dynamic load, which was an effect of numerous low energetic rockmass tremors. These tremors, related to excavated longwall, were located in close proximity of roadway in its part where the biggest convergence occurred. In current practice, in this type of convergence prognosis, the maximal value of dynamic load exerted on roadway resulted from single rockmass tremor is taken into consideration. Quantitative consideration of all tremors including their location is impossible at the stage of convergence prognosis because of lack of this type of data. This paper presents results of roadway convergence prognosis compared to results of underground investigation. Conclusions formulated on that base allow in future similar designing works for obtaining more accurate results.

Jan 1, 2013

By Neda Zangeneh

Production efficiency from low permeability gas shales require techniques to optimize hydraulic fracture completions. One completion strategy involves the simultaneous or near simultaneous hydraulic fracturing of multiple horizontal wells to maximize the fracture network area and stimulated reservoir volume. However, changes to the in-situ stress field caused by an earlier hydrofrac on subsequent hydraulic fractures are not accounted for in traditional hydrofrac design calculations. Presented here are the results from a set of transient, coupled hydro-mechanical simulations of a rock mass containing two wellbores using the discontinuum-based distinct-element method. The results demonstrate the influence of stress-shadows generated by a hydraulic fracture on the development of subsequent hydrofracs from an adjacent well. It is shown here that these interactions have the potential to change the size and effectiveness of the hydraulic fracture stimulation by changing the extent of the hydraulic fracture around the secondary well.

Jun 1, 2012

By Y. M. Zhu, G. C. Gong

"The influences of citric acid (CA) on the flotation behavior of cassiterite using styrene phosphonic acid (SPA) as the collector were studied via single mineral flotation tests, contact angle measurements, zeta potential determinations and solution chemistry calculations in this paper. The results of single mineral flotation tests revealed under the conditions that pH=4 and the dosage of SPA 100 mg/L, the recovery of cassiterite reached 76.78%. The addition of 20 mg/L AC decreased the recovery by 12.42% at pH=4. Contact angle measurements demonstrated the adsorption of CA prior to SPA made the cassiterite more hydrophilic. The results of zeta potential determinations and solution chemistry calculations indicated the chemisorption of C6H7O7- and C6H6O72- filled parts of the Sn site on cassiterite surface and prevented the SPA from getting adsorbed. The hydrophilic effect of AC was stronger than the hydrophobic effect of SPA and the flotation of cassiterite was crippled. INTRODUCTION Tin is an important metal which is widely used in medical instruments, marine engineering materials, electronic and electrical devices, welding, weapon manufacturing and organotin compounds industries (Angadi et al., 2015). Cassiterite is the only mineral from which the tin can be extracted, thus it is of great importance to efficiently exploit the cassiterite mineral. Flotation is an indispensable method for the recovery of cassiterite (Li et al., 2015). However, cassiterite is usually in association with many other gangue minerals which are of similar floatability, such as quartz, calcite, fluorite, iron oxide, wolframite, scheelite and tourmaline (Sreevinas, 1997). So some modifiers are necessary in the cassiterite flotation process. The amounts of the modifiers used in the flotation must be judicious and the overmuch modifiers may cripple the recovery of cassiterite (Parsonage et al., 1987). Nevertheless, the research about the effects of the modifiers on the flotation behavior of cassiterite has been rarely reported. In this paper, the influences of citric acid (CA) on the flotation of cassiterite using styrene phosphonic acid (SPA) as the collector were investigated by flotation tests, contact angle measurements, zeta potential determinations and solution chemistry calculations."

Jan 1, 2018

By Y Tsukurimichi, D Asahina, T Endo, T Takemura

Scientific knowledge of Mars’ surface morphology and internal geological structure has been accumulated through satellite imagery and numerical topographic data using remote sensing technology, as well as seismic surveys by the on-site lander. Recent studies show that Marsquakes could be caused by the release of strain energy generated by the contraction of Mars. In particular, Marsquakes occur around the graben where many faults are existed and formed regularly spaced patterns. This implies that Marsquakes occur when the stress field of the Martian crust is an extension condition, and normal faults appear on the surface. We focus on the linear relationship between the fault spacing and the thickness of the mechanical layer as an approach to studying the internal structure from satellite images. Mechanical layer is a layer that composes of the same mechanical properties and is mainly bounded by lithology (Narr, 1991; Gross, 1993). The linear relationship between the thickness of the mechanical layer and the joint spacing has been studied and its slope is called the Fracture-Spacing Index (FSI) (Narr and Suppe, 1991). Soliva, Benedicto and Maerten (2006) showed that the stress drop zone (stress shadow) due to the fault activities affects the fault spacing. Figure 1 shows the approach used to estimate the thickness of the mechanical layer from the fault spacing on Mars. This paper aims to better understand the internal mechanical structure of Mars estimated by the geometrical pattern of faults on the Martian surface. We report the initial studies of this work. The lab-scale physical experiments and numerical experiments were presented to demonstrate the relationship between the thickness of the mechanical layer and the geometric pattern of fractures

Nov 29, 2022