Search Documents

By K. M. Swanson

El presente texto describe la eficiencia del laboratorio protegido con el blindaje de Duunreay, Escocia, perteneciente al Centro Experimental de Reactores de la Comisión de Energía Nuclear del Reino Unido. El laboratorio ofrece una combinación única de medios sencillos de manipulación del combustible nuclear altamente radiactiva y de un conjunto de aparatos verificadores y experimentadores para múltiples usos, cuya función es estudiar el combustible de reactor.

Sep 1, 1965

By Enrique Monge

Dado que a nivel universitario existen pocos laboratorios adecuados de Física y Química en el Perú, se ha desarrollado proyectos de laboratorios privados y plantas experimentales tanto en el campo analítico y metalúrgico que encauzen la industria minera por el sendero de la técnica más elemental. En ese sentido, el presente texto señala la importancia de los laboratorios de investigación para las industrias mineras y metalúrgicas a través de la Universidad Nacional de Ingeniería y el apoyo del Estado. El laboratorio está dividido en 6 secciones: Minería, preparación y concentración de minerales; metalurgia de minerales no Ferrosos; carbón; fierro y acero; metales y aleaciones.

Jan 1, 1959

By R. Gong, R. Bhaskar

[Full-scale laboratory experiments were performed to evaluate the effect of ventilation and water spray pressure on the potential dust capture efficiency of a ventilation system comprised of blowing ventilation and an underboon scrubber. The tests were performed for a 1.52-m (5-ft) roof height and 2.36 m-3/s (5000 cfm) blowing ventilation volume, and a 2.44-m (8-ft) roof height and 4.72 m3/s (10.000 cfm) blowing ventilation volume at three face positions of the miner. The scrubber suction rate was varied for the tests to study the effect of scrubber flow rate on capture efficiency. The airflow patterns and scrubber efficiency were determined by performing tracer gas tests. Tracer gas was released through a manifold placed in front of the rotating miner drum. The gas was sampled in a grid fashion using a real-time multi-point gas sampling system. The capture efficiency of the scrubber was evaluated based an the peak gas concentration of the gas laden air drawn through the scrubber and the amount of gas passing, through the scrubber as a fraction of the gas released at the face. The data were analyzed to yield scrubber peak concentrations, potential exposures at various operator locations and the gas removal percentage (GRP). The underboom scrubber appears to work best in the end sump position, relative to the start sump and start slab positions. The capture efficiency scrubber was higher for 2.44-m (8-ft) roof heights compared to 1.52-m (5-ft) roof heights. The data also showed that the scrubber air discharged behind the mining machine may be drawn into the face area by the action of the blowing ventilation system, resulting in recirculation.]

Jan 1, 1994

By Yoginder P. Chugh

The characteristics of weak floor strata associated with actively mined coal seams in Illinois are very important from ground stability point of view and, in many cases, are the governing factors in determining the size of pillars and mine openings. Laboratory and field getotechnical characterization studies of weak floor strata were conducted at six mines during the period 1985-1988. Correlation analysis among engineering index properties, and laboratory, and field determined strength-deformation properties were conducted to identify simple tests which can be used to estimate ultimate bearing capacity and deformation properties of immediate floor strata. It was concluded that the ultimate bearing capacity (UBC) and strength- deformation properties of the weak floor strata can be estimated from simple tests such as, natural moisture content, atterberg limits, and axial swelling strain. Indirect tensile strength was found to be a better estimator of UBC than unconfined compressive strength.

Jan 1, 1989

The National Institute for Occupational Safety and Health (NIOSH) conducratory and field tests to evaluate the effectiveness of dust collector bags for reducing dust liberation and operator exposure from a roof bolter?s dust collection system. The laboratory tests evaluated the bag?s effectiveness to contain dust and the effect on canister filter loading in both a bag and bagless condition. The dust emissions from the collector?s exhaust were also measured in each condition during laboratory testing and show that nearly 100% of the test dust fed into the collector was captured by the dust bags. Loading and pressure drop on the dust collector?s canister filter is greatly decreased when using the bags, enabling longer periods of drilling without filter removal/cleaning. The field results showed that, even though dust standards were met, respirable dust in exhausted emissions was reduced around the bolter. Laboratory and field results show that benefits from use of the bags are realized in all areas of operator exposure.

Jan 1, 2008

By T. W. Beck

The National Institute for Occupational Safety and Health (NIOSH) conducratory and field tests to evaluate the effectiveness of dust collector bags for reducing dust liberation and operator exposure from a roof bolter’s dust collection system. The laboratory tests evaluated the bag’s effectiveness to contain dust and the effect on canister filter loading in both a bag and bagless condition. The dust emissions from the collector’s exhaust were also measured in each condition during laboratory testing and show that nearly 100% of the test dust fed into the collector was captured by the dust bags. Loading and pressure drop on the dust collector’s canister filter is greatly decreased when using the bags, enabling longer periods of drilling without filter removal/cleaning. The field results showed that, even though dust standards were met, respirable dust in exhausted emissions was reduced around the bolter. Laboratory and field results show that benefits from use of the bags are realized in all areas of operator exposure.

The National Institute for Occupational Safety and Health conducted laboratory and field tests to evaluate the effectiveness of dust collector bags for reducing dust liberation and operator exposure from a roof bolter?s dust collection system. The laboratory tests evaluated the bag?s effectiveness to contain dust and the effect on canister filter loading in both a bag and bagless condition. The dust emissions from the collector?s exhaust were also measured in each condition during laboratory testing. Laboratory results show that nearly 100 percent of the test dust fed into the collector was captured by the dust bags. Loading and pressure drop on the dust collector?s canister filter is greatly decreased when using the bags, enabling longer periods of drilling without filter removal/cleaning. The field results showed that, even though dust standards were met, respirable dust in exhausted emissions was reduced around the bolter. Laboratory and field results show that benefits from use of the bags are realized in all areas of operator exposure.

Jan 1, 2008

By Stephen C. Tadolini, John Bolton, Bre-Anne Sainsbury, Tom Meikle

"The capacity of ground support components which have been affected by corrosion is reduced and may ultimately lead to dynamic failure of the component and the strata. In order to maintain an effective, long-term ground support system, significant campaigns of rehabilitation are often required in corrosion affected areas which also expose the workers to hazardous conditions. The most common corrosion protection for steel ground support utilises sacrificial systems such as galvanising. Galvanising has previously been proven to be susceptible to some corrosion processes. Stainless steel is the most effective in resistance to corrosion, but can be cost prohibitive, and its mechanical properties often make it unsuited to use in ground support components.Providing an outer protective plastic coating to bolts has proven to be an effective means of protecting the inner steel bar from corrosion. However, these support systems tend to be susceptible to coating damage, and require post cement grouting to provide full encapsulation. In comparison to a standard bolt/resin system, they can be slow to install and expensive. These systems have also been shown to reduce overall load transfer performance of the bolting system.In order provide a higher level of corrosion protection whilst maintaining current installation practices and bolting cycle times, Minova has developed the Enduro™ Steel Ground Support Range. The Enduro™ range consists of standard Minova steel ground support components which have been treated with a unique coating process. The Enduro™ coating has been tested in the harshest of conditions, in laboratory controlled conditions and in underground trials. It has been proven to effectively resist or completely eliminate the formation of corrosion, even in the most aggressive environments. This paper explains the process and provides the details of the laboratory and underground corrosion performance testing carried out on Enduro™ ground support products.INTRODUCTIONTraditionally, the most common form of corrosion protection in steel ground support consists of a sacrificial protective coating such as galvanising (Aziz, et al., 2013). Such coatings have proven to be ineffective in extreme high and low pH conditions with corrosion of the support system commonly encountered. There is also evidence that common forms of galvanising may actually increase the rate of corrosion in certain pH environments. Figure 1 shows typical corrosion and failure of a standard re-bar roof bolt."

Jan 1, 2016

The design of excavations in high displacement mining environments requires consideration of both the load and displacement capacity of the ground reinforcement and support systems. This paper is a case study on the design of point anchored rebar bolts using laboratory tests and field trials at the Ridgeway Deeps block cave. A laboratory testing program was carried out to measure the mechanical properties of the Strata Control Systems R27 Secura resin bolt which is currently being installed on the extraction and undercut level at the Ridgeway Deeps block cave. The aim was to quantify elastic, plastic and energy parameters for various bolt, mesh and plate systems. Experiments were performed on bar segments, bolt/plate systems, and bolt/plate/mesh/resin systems. The mechanical properties were calculated from tensile tests with a 500 kN Avery machine. Load-displacement data was collected from four different testing configurations. The laboratory results are compared with underground measurements and observations of bolt performance.

Nov 25, 2010

By B. Tiryaki, M. Ayhan, O. Z. Hekimoglu

"This paper discusses the aspects of tracking cutters related to the computer-aided design of shearer drums. A comprehensive computer analysis of drum dynamic parameters for multi-tracking tool arrangement is not presently available, as the current computer programs mainly consider the aspects of single tracking. Despite the fact that the single-tracking arrangement is recommended for efficient cutting, some major drum manufacturers have been seen to persistently adhere to multi-tracking, probably due to a lack of information. Further studies in this field are believed to contribute greatly to the current understanding of the computer-aided design of shearer drums.A number of laboratory simulation trials and long-term underground investigations were carried out in detail on tracking cutter arrangement, and an equation required for a computer program was derived. The results obtained from computer assessment of dynamic parameters for drums with multi-tracking arrangement were found to be in accordance with those of the underground trials, indicating the validity of the equations. The procedure adopted for the computer appraisal of the shearer drums designed with a multi-tracking concept, as described in this study, is therefore recommended to be considered in the currently employed computer programs."

Jan 1, 2003

By John D. VandeKraats

Yielding rock bolt systems have been developed to provide ground support while accommodating shifting, creeping, or swelling ground movements. The Dywidag Systems, Inc. (DSI) Slip Nut System is one such system. It has been tested in the laboratory and installed and monitored in the interbedded halite and anhydrite at the Waste Isolation Pilot Plant (WIPP) since 1994. The Slip Nut System is installed on a point anchored threaded bar or on a threaded bar coupled to a cable bolt. At a pre-engineered load the nut acts as a die and cuts through the thread on which it rests, thereby reducing the load and coming to rest on the next thread where the process repeats. Two types of laboratory tests were performed using slip nuts on DSI's threaded bars and their Tensionable Cable bolts. Straight pull tests exceeding 0.3m (1 ft.) of displacement were performed on the systems. Also, offset tests were performed on these bolt systems in a test frame designed to simulate WIPP geologic conditions. A room scale test area consisting of 186 threaded bars began in 1994. Select bolts were instrumented to track bolt load. All bolts were tracked through time for operation. Through three complete years since installation over twelve slips, corresponding to approximately 0.15m (6 in.) of ground movement, have been observed in some areas. Since installation strata offset has exceeded 0.08m (3 in.) at a supported clay layer in the roof. No bolt failures have been observed. Slip loads observed underground generally approximate those observed in the lab. To date, the slip nut systems tested and installed have performed as expected.

Jan 1, 1998

By L. Wade, D. R. Pearce

A detailed account is given of the spectral ratio laboratory method for the determination of seismic velocity and attenuation through rock cores under simulated in-situ stress conditions. An account of a computer program called AUTOQ is described for automatic processing of a complete set of laboratory results. Some of these results are shown and discussion is directed to- wards the suitability of in-situ velocity or attenuation measurements in determining rockmass condition or stress regime.

Jan 1, 1996

Inco Limited has been evaluating options for streamlining the overall flowsheet at its Sudbury, Ontario operations to improve productivity and to minimize the cost of at¬mospheric emissions reduction. Some of the flowsheets being considered include vari¬ous levels of copper/nickel separation at the Clarabelle Mill where all Inco's Sudbury Basin ores are processed. This paper reports on the laboratory and miniplant studies car¬ried out during the flowsheet development for a commercial Cu/Ni separation plant. There are two potential feed streams for Cu/Ni separation. It was determined that Cu/Ni separation from the rougher concentrate requires no regrind, and a very clean copper concentrate is produced, but the recovery of copper is limited to about 70% from ore. Cu/Ni separation is more difficult from the bulk concentrate because of the presence of excess flotation reagents in the slurry and due to locked particles. By replacing the slurry water with clean process water, and by addition of some hydrogen peroxide, entrainment is minimized and excess reagents are removed from the surface, providing a satisfactory separation of copper from nickel. Fine regrinding is required to increase liberation of the locked particles and to obtain 85% copper recovery with minimal nickel contamination of the concentrate.

Jan 1, 2005

By M. Q. Xu

During the flowsheet development for a potential commercial Cu/Ni separation plant at the In-co?s Sudbury operation, extensive laboratory and miniplant studies were carried out. There are two potential feed streams for Cu/Ni separation at the existing operation. It is shown that Cu/Ni separation from the rougher concentrate is relatively simple without need of regrind. However, Cu/Ni separation can be difficult from the bulk concentrate because of the presence of excess flotation reagents in the bulk concentrate slurry and locked particles. Excess flotation reagents created excess froth increasing entrainment. By replacing the slurry water with tap water and with addition of some hydrogen peroxide, entrainment is minimized and good Cu/Ni separation is achieved on the bulk concentrate. Fine regrind is required to increase liberation of the locked particles for ultimately high copper recovery at the minimal nickel content.

Jan 1, 2014

By M. Cavallini, G. Cannavale, P. P. Milella, A. Pescetelli, C. Lupi

Ni-Cd sealed and vented cells have been widely used in the last few years. The environmental hazard related to the heavy metals contained in Ni-Cd batteries is well known. Therefore, a number of scientific studies and commercial processes have been implemented in order to recycle them. Since spent batteries are a heterogeneous and complex material, any kind of recovery process needs some preliminary treatments. The proposed process described in this paper has been tested in laboratory and further developed in a pilot plant. It consists of a combination of mechanical and hydrometallurgical treatment steps, and is able to treat all type of Ni-Cd batteries. In particular, the mechanical treatments have to be done separately on vented and sealed cells, while the hydrometallurgical step is performed on a mixture of the two products obtained from mechanical steps. A fully automated dismantling line would allow the separate recovery of the plastic or metallic casing, terminals, KOH electrolyte, and electrodes to be further processed· for Ni and Cd recovery. The electrodes coming from dismantling line and sealed batteries are submitted separately to an original crushing and elutriation treatment to separate metallic and active paste in the first case and metallic, plastic and active paste in the second case. The hydrometallurgical treatment is carried out on active paste bearing product to produce Ni, Cd, and Fe comn1ercial salts through acidic leaching followed by a multi-step solvent extraction operation to obtain pure solutions.

Jan 1, 2000

By S. M. Bulatovic, D. M. Wyslouzil, K. R. Rawlings

"The suitability of a new organic reagent DS20 as a depressant for oxidized and carbonaceous pyritic lead-zinc ore from Nanisivik Mines Ltd. has been evaluated in the laboratory and in the plant.The depressant DS20 is a mixture of Lignosulphonate-Dextrin-Quebracho and was developed specifically for depression of highly oxidized and carbonaceous pyrite.The laboratory test work indicated that the poor metallurgy resulting from the oxidized ore could be improved to normal plant performance by the addition of the DS20 depressant with the existing plant reagents. The laboratory data suggested that lime consumption could be reduced when using DS20.In this paper, the development work and the plant trials with DS20 are described.INTRODUCTIONNanisivik Mines Ltd. treats approximately 2000 tonnes per day of lead-zinc massive sulphide ore, containing currently 1% Pb and 9% Zn. The concentrator operations have been described previously (1,2) and typical metallurgical performance is detailed in Table I.The concentrator flowsheet (Figure No. 1) and the standard reagent scheme (Table No. 2) demonstrate the relative simplicity of treatment of this coarse grained ore.A recently discovered satellite orebody - Area 14 - containing 2% Pb and 12% Zn was brought into production in October 1983. This ore had been oxidized to varying degrees by ground water; the pyrite mineralization was found to be very fast floating and a carbonaceous constituent present in higher than normal proportion also affected flotation. The simple high lime addition could not control the pyrite, and very low grade lead concentrates resulted; zinc metallurgy was also affected by this oxidized condition (Table 3)."

Jan 1, 1986

By F. Q. Su

Underground Coal Gasification (UCG) is a promising environmentally acceptable clean-coal technology. A typical UCG system has two wells drilled from the surface into a coal seam with some separation of injection from production. The wells are connected underground by various linking techniques. After creating a combustion reactor in an underground coal seam, air and oxygen flow through the injection well. Heat energy and gases are collected from the production well. As gasification progresses, the combustion reactor is moved along the linking hole. Using this process, the fracturing activity inside the coal seam serves an important role for enlargement of the gasification zone because the surface area oxidization increases continuously by coal cracking. For effective coal gasification, fracturing activity must be controlled. Moreover, excess fractures inside the coal seam and surrounding rock can induce gas leakage, underground water contamination, subsidence, etc. Therefore, monitoring and control of fracturing activity in underground areas constitute key technologies for efficient and safe UCG. To monitor fracturing activity, we conducted laboratory and small-scale field experiments of UCG using acoustic emission (AE) measurements. UCG model tests were conducted for linking and coaxial types UCG models. Coaxial UCG systems are compact and are anticipated for application in underground coal seams having a complex geological structure. The UCG model consists of a coal block molded in a steel canister (20 liter capacity) with heat-resistant mortar, with a linking hole or a coaxial-hole passing through the coal block. During coal combustion, coal temperatures, production gas contents, and AE activity were monitored under the control of injection-air and oxygen flow rates. Results show that the combustion propagated inside the specimen along the linking hole. Many AE events were generated during coal combustion. The AE activity was related closely to temperature changes inside the coal block. This AE generation apparently results from crack initiation and extension around the coal combustion area under the influence of thermal stress. However, comparing the results from UCG models of linking and coaxial types, the gasification of the linking type model showed an average calorific value as high as 11.3 MJ/m3. The coaxial type yielded an average calorific value of produced gas as only 5.79 MJ/m3. In the coaxial type of UCG model, the combustion region was limited to the area around the coaxial hole. The AE activity was lower than in the linking type model. For small-scale UCG field experiments, linking and coaxial types were tested at an open pit coal mine in Hokkaido, Japan. Using a linking type UCG, 58.2 kg coal was processed in 39 h, with the calorific value estimated as 11 MJ/m3. However, the coaxial type UCG processed 7.0 kg coal in 9 h, yielding an estimated calorific value of 6.0 MJ/m3. These tendencies resemble those of results of laboratory UCG experiments. Results of these experiments demonstrate that AE monitoring is a useful tool to evaluate combustion reactors for efficient and safe UCG systems. To develop a coaxial UCG system, results show that fracture control around combustion reactors is indispensable.

Aug 1, 2013

By M. P. Brameld, G. Archambault, R. H. McCorkell

"The rates. J. at which materials emit radon are of interest in studies of the sources of radon in mines. buildings. soils overburden and other places where it may indicate the location of ore or be a health hazard. Here J values were determined by measuring the radon concentrations by means of scintillation counters or alpha-particle track detectors in chambers in which specimens were sealed. Errors in the measurements due to leakage from the chambers. lack of secular equilibrium in the decay series of the radon measured, or the limited rate of diffusion of radon from powders or within the chambers were shown to be insignificant or could be corrected. Scintillation counter measurements are highly reproducible; track detector measurements also appear useable and may be made on many small samples using small, simple chambers. J measurements were made for uranium ores, drill cores, standard CANMET pulps. concrete and gypsum board. Powdering of ores had little effect on their J values.IntroductionIn the mining and mineral sciences, radon (222Rn) is of interest chiefly for two reasons: in geochemical exploration for mineral deposits its presence in soil. overburden and water in more than background concentrations may indicate the existence and locations of uranium deposits and, if present in sufficient concentrations, it is a possible health hazard in mines, mills and other places where people live and work. The latter aspect of radon's role has received considerable attention recently(1,2,3,4,5), and surveys of soil-gas radon concentrations have been used for some time in searches for uranium deposits(6,7,8,9,)."

Jan 1, 1981

By V. B. Achanti

Laboratory studies were carried out at West Virginia University to investigate the rock fragmentation mechanism by continuous miners using an automated rotary cutting simulator. The primary factors influencing the: fragmentation process were found to be: bit spacing, bit geometry, depth of cut, and cutting drum rotational speed. This paper presents the influence of these parameters in achieving optimum energy consumption and minimizing dust generation during rock fragmentation process. Three bits were used simultaneously on Indiana limestone while the bit tip angle was varied from 60° to 90°. Bit spacing was varied from 2.54 cm (1 in.) to 5.08 cm (2 in.) while the cutting process was assessed for varying cutting depths. Respirable dust generated during the course of the experiments was analyzed utilizing cascade impactors. Assessment of these parameters has led to a better understanding of the cutting mechanism by continuous miners in terms of energy consumption and dust generation.

Jan 1, 1997

By V. B. Achanti, A. W. Khair

Laboratory studies were carried out at West Virginia University to investigate the rock fragmentation mechanism by continuous miners using an automated rotary cutting simulator. The primary factors influencing the fragmentation process were found to be: bit spacing, bit geometry, depth of cut and cutting drum rotational speed. This paper presents the influence of these parameters in achieving optimum energy consumption and minimizing dust generation during rock fragmentation process. Tree bits were used simultaneously on Indiana limestone while the bit tip angle was varied from 60° to 900. Bit spacing was varied from 2.54 cm (1 in.) to 5.08 cm (2 in.) while the cutting process was assessed for varying cutting depths. Restorable dust generated during the course of the experiments was analyzed utilizing cascade impactors. Assessment of these parameters has led to a better understanding of the cutting mechanism by continuous miners in terms of energy consumption and dust generation.

Feb 24, 1997