Search Documents

By Walter I. Paniagua

Drilled shafts and precast concrete piles were installed for the foundation of several structures in a reconfiguration project of a refinery in Minatitlan, Veracruz, in the Gulf of Mexico. The soils are alluvial deposits of flat land from the Coatzacoalcos River, which are embedded with layers of sand, soft clay, and peat. As part of a QC/QA program, load tests, both static and dynamic, axial and lateral, were performed. In this paper results of 32 axial tests are presented, in which typical load-displacement curves were measured at the top of the foundation elements; from the interpretation of these plots, data were recorded for ultimate side shear and in some cases for end bearing capacities, which are compared with the theoretical results of the final stage of the foundation design. The comparison shows that under allowable loads, side shear determines the bearing capacity of piles, even when the tip is embedded in a hard layer. Underestimation of the side shear is evident; therefore design criteria, as well as the methods used for obtaining soil parameters, should be reviewed.

Jan 1, 2007

By Paul C. Hagan, Jianhang Chen, Serkan Saydam

"Modified cable bolts are commonly used in underground mines due to their superior performance in preventing bed separation when compared with plain strands. To better test the axial performance of a wide range of cable bolts, a new Laboratory Short Encapsulation Pull Test (LSEPT) facility was developed. The facility simulates the interaction between cable bolts and surrounding rock mass, using artificial rock cylinders with a diameter of 300 mm in which the cable bolt is grouted. Furthermore, the joint where the load is applied is left unconstrained to allow shear slippage at the cable/grout or grout/ rock interface. Based on this apparatus, a series of pull tests were undertaken using the MW9 modified bulb cable bolt. Various parameters including embedment length, test material strength and borehole size were evaluated. It was found that within a limited range of 360 mm, there is a linear relationship between the maximum bearing capacity of the cable bolt and embedment length. Beyond 360 mm, the peak capacity continues to rise but with a much lower slope. When the MW9 cable bolt was grouted in a weak test material, failure always took place along the grout/ rock interface. Interestingly, increasing the borehole diameter from 42 mm to 52 mm in weak test material altered the failure mode from grout/rock interface to cable/grout interface and improved the performance in terms of both peak and residual capacity.INTRODUCTIONFully grouted cable bolts have been used in underground mining industry for many decades. Initially, plain cable bolts manufactured by winding seven flexible steel wires together were commonly used (Thorne and Muller, 1964). Laboratory and field tests lead to a better understanding of the transfer process between grouted cable bolts and the surrounding rock mass, which is beneficial to improve the reinforcing performance of cable bolts in engineering practice (Fuller and Cox, 1975; Cox and Fuller, 1977; Schmuck, 1979; Stillborg, 1984). Nevertheless, as in many cases the initial cable was sourced from discarded steel with a smooth surface along the strand, plain cable bolts did not always meet performance expectations (Windsor, 1992). Over time, it was realised that cable surface geometry plays an important role in determining anchorage performance. Consequently, modified forms of cable bolts were developed. For instance, twin-strands which were made by using spacers to combine two plain cables together improved anchorage capacity two-fold (Matthews, Tillmann and Worotnicki, 1983). However, this required a large borehole to be drilled. Epoxycoated strands had remarkable performance in practice but were difficult to install without damaging the epoxy layer (Dorsten, Hunt and Kent, 1984). In the 1990s, there was a rapid development in the cable bolt design. A typical example was birdcaged cable bolts. They were initially suggested by Hutchins et al. (1990) via unwrapping traditional seven-wire strands and generating a number of nodes together with antinodes along the strand. But it was difficult to make birdcaged cable bolts that could be coiled for transporting."

Jan 1, 2015

By Jacob Chacko

The east span of the San Francisco-Oakland Bay Bridge (SFOBB), which is one of the most heavily traveled bridges in the world, will be replaced due to seismic safety concerns. The majority of the new bridge will be founded on large-diameter (1.8 to 2.5 meters), approximately 60- to 100-meter-long pile foundations The large-diameter steel pipe piles and soil conditions are similar to those used/encountered in many offshore structures. Thus, the design methods used are based on site-specific modifications to the procedures recommended by the American Petroleum Institute rather than the conventional procedures that have been formulated and used for the design of much smaller piles. Pile foundations will experience their maximum loads during the design earthquake. For the Safety Evaluation Earthquake, tension loads of up to approximately 80 to 90 meganewtons (MN) and compression loads of up to approximately 120 to 140 MN were calculated. Due to the economic importance of the SFOBB and the consequences of catastrophic failure in both economic and human terms, the design and analysis of the pile foundations supporting the bridge consider a number of aspects of pile-soil behavior that are normally ignored. Those aspects include: 1) the effects of consolidation and setup, 2) the behavior under dynamic loading, 3) the losses of resistance under cyclic loading, and 4) the load-settlement behavior of the piles under severe cyclic loading conditions. Since the treatment of complex aspects of pile foundation behavior is not codified in any guiding documents, several project-specific methods were developed for design and analysis of the foundation piles.

Jan 1, 2002

By Fawad S. Niazi

Ever since the use of the cone penetration test (CPT) in geotechnical practice, attempts have been made to correlate CPT parameters with pile capacity components of unit end bearing (qb) and unit shaft resistance (fp), thus deriving multiple CPT-based pile design methods. These methods focus on "capacity" only without consideration to complete axial pile load-displacement (Q-w) response. Estimated capacities from these methods also exhibit considerable scatter without any consensus on their consistency. In addition, load-displacement curves obtained from axial load tests on highly expensive and extensively instrumented piles can exhibit different shapes. Nevertheless, a single value from the curve so obtained dictates the design capacity. Currently, there are at least 42 different criteria defining capacity with considerable variation in the values obtained thereof. The Randolph elastic solution, which provides a framework for analytical evaluation of pile load-displacement response, requires the profiles of soil stiffness. The fundamental soil stiffness defined by the small-strain shear modulus (Gmax) can be obtained from shear wave velocity (Vs) readings via seismic piezocone tests (SCPTu). The secant stiffness (G), which softens from Gmax corresponding to operational load levels, can be obtained by generating stiffness reduction curves from back analysis of load tests. Then, using appropriate G values, the Q-w curve can be defined for conditions similar to the database from the pseudo strain (w/d). Thus, a complete framework for optimal integration of SCPTu data, Randolph elastic solution and back-analysis of field operational stiffness can be established for complete axial pile foundation analysis.

Jan 1, 2011

By Paul W. Mayne

The axial load-displacement-capacity and load-transfer response of deep foundations can be conveniently assessed by geophysical piezocone tests that provide four independent readings with depth, including tip stress (qt), sleeve friction (fs), porewater pressures (ub), and shear wave velocity (Vs). The penetration data (qt, fs, and ub) of the CPT are utilized to obtain the pile side friction (fp) and end bearing capacity (qb) while the shear wave measurements provide the initial stiffness. Within an elastic continuum framework, the axial pile deflections are calculated and an approximate nonlinear response is obtained by modulus degradation from small-strain response (G0) to intermediate- and large-strains (G). The continuum solution permits separation of load transfer along the sides and proportion to the base. Applications are shown for case studies involving an end-bearing drilled shaft, two friction-type drilled shafts in Alabama and Georgia, and a "Class A" prediction involving driven pipe piles in residuum of the Atlantic Piedmont geology. Load-transfer data were available for the drilled shaft foundations.

Jan 1, 2002

By Alvaro Fernández-Baca, Richard Chaiña

El proyecto Ayawilca, controlado al 100%por Tinka Resources y ubicado en el Perú central, contiene un expectante descubrimiento de zinc-estaño en un sistema de reemplazamiento en carbonatos (CRD), así como un recurso de plata cercano a la superficie. Basado en sondajes completados hasta finales de 2015, Tinka anunció un estimado de recursos minerales inferidos para la zona de zinc de 18.8 millones de toneladas con 8.2% de zinc equivalente, y un primer estimado de recursos minerales inferidos para la zona de estaño de 5.4 millones de toneladas con 0.89% de estaño.

May 1, 2008

By S. Coats, G. Norton, A. Benham, P. Ková

The Aynak copper deposit, located 30 km south of Kabul in Afghanistan (Figure 1), was discovered by Soviet geologists in the 1970s. Extensive exploration undertaken in the area between 1974-80 included several hundred boreholes, seventy trenches and nine exploratory adits. This work identified a “drill-indicated resource” of 240 Mt at 2.3% Cu (ESCAP, 1995).

Jan 1, 2007

By K. Tada

A surface of a magnesium slab (hereinafter, referred to as Mg slab) or magnesium alloy slab (hereinafter, referred to as Mg alloy slab) becomes black with the use of conventional manufacturing methods. The methods also involve a danger that an explosion of the molten magnesium occurs through contact with cooling water. Thus, it has been impossible to produce a slab having a smooth surface. In the present method, a molten magnesium alloy is supplied into a mold, which is sheltered from the surroundings, from a pool in tundish, which is shielded from the surroundings. AZ31B slab formed in the mold is drawn horizontally out to the outside from an outlet of the mold by revolving of the pinch rolls. A cooling water is jetted at an acute angle onto the slab on the outer side of the mold outlet. Further, an inert gas is sprayed at the inner side of the mold outlet in order to seal in a gap between a free surface of the molten magnesium alloy and a sheltered board surrounding an upper surface of the mold. As a result, oxygen and droplets of the cooling water are prevented from running back to the mold side through the gap. AZ31B slab has a smooth surface condition and high quality without a gas porosity, a segregation or the like. Further, the slab has a size of a width of 100 to 120 mm, a thickness of 5 to 20 mm and a span of 10 m or more.

Jan 1, 2006

By Robert Martin, Brian W. Stump

As part of a series of seismic experiments designed to improve the understanding of the impact of mining blasts on verifying a Comprehensive Test Ban Treaty, a sixteen station network of three-component seismic sensors were deployed around a large cast shot in the Black Thunder Mine. The seismic stations were placed, where possible, at a range of 2.5 kilometers with a constant inter-station spacing of 22.5 degrees. All of the data were recorded with the seismometers oriented such that the radial component pointed to the middle point of the approximately 2 kilometer long shot. High quality data were recorded at each station. Data were scaled to a range of 2.5 kilometers and the sum of the absolute value of the vertical, radial, and transverse channels computed. These observations were used to construct radiation patterns of the seismic energy propagating from the cast shot. It is obvious that cast shots do not radiate seismic energy isotropically. Most of the vertical motion occurs behind the highwall while radial and transverse components of motion are enhanced in directions parallel to the highwall.

Jan 1, 1997

By D. Vogt

South African underground hard rock mines are typically managed using measurements made daily, weekly or even monthly of key parameters such as face advance, readiness to blast, blast success, temperature or dust levels. Health, safety and productivity can all be greatly improved if a real-time measurement system can inform decision making. To enable this vision of widespread sensing, communication and decision support, CSIR has developed an open standard architecture for communication of sensor data, and a reference implementation using that standard. The standard, called AziSA, meaning ?to inform? in isiZulu, will allow any device that complies with it to join any network that supports it. The standard is designed for South African gold and platinum mines. To be practical in a typical Bushveld platinum mine, a real-time sensor system needs to be robust, reliable and cheap: ?Sensors are equipped with power sources that will last as long as the sensor is required. In effect, sensors need to be disposable: cheap enough not to warrant repair if they break. ?Communication in the stope is wireless, to avoid there liability problems associated with wire connections. For example, wires to sensors in the face area are unlikely to survive blasting. ?To get information out of the stope, the power line to the scraper winch is used as a communications link. Unlike a separate communications link, the power line will be repaired if damaged, because of its importance to production. ?Outside the stope, communications are transferred onto the mine communication infrastructure. To succeed as a management system, the next key element is the use of software decision support tools that will analyse masses of real-time data to extract key parameters and trends for decision makers. A range of sensors has been developed, including commercial sensors that have had wireless adapters added to make them AziSA compliant, and bespoke sensors that provide low cost sensing of typical mining parameters. An important parameter in any sensor network is the location of the sensor. This has to be easy and cheap to establish, so a tool has been developed to locate sensors in the confines of a stope, using ultrasonic and radio techniques. Once sensors are installed and located, they associate their location to all data that they produce. All the data from the system are captured at surface in a flexible database that can be queried by any application that requires data of any kind. It is simple to program alerts, and for actions to be associated with alerts. The use of wireless in stope also allows for communication from surface to the stope, or from stope to stope. The first implementation of an AziSA compliant system is being installed as part of the Mine Health and Safety Council funded rockfall elimination project. The design is discussed, and a future application for a platinum mine is considered.

Jan 1, 2009

By V. Roze, M. E. A. Robertson, C. J. Sharland

Current Techniques - Fire Assay Fire assay of gold has been used for several thousand years and is a well known technique to the traditional assayer. Very few assayers wish to use the method but to date there has been no viable alternative. Fire assay is expensive in labour, time, capital and running costs. Workers can be exposed to hazards and uncomfortable working conditions such as lead fumes, heat stress, dust and eye strain. The high capital cost of putting up the building and equipping it, together with running costs which increase annually at a prohibitive rate makes the technique less attractive each year. The main requirement in most assay laboratories is to maximise throughput economically. This is difficult with fire assay as it is impossible to automate. Each sample for analysis is handled by at least 12 people and each person represents a potential source of error. Record keeping and report generation has to be done manually which is both slow and prone to errors. Replacement of staff requires a considerable training period and with a large turnover of personnel this presents yet another problem. The presence of silver and dross in the gold sample affects the accuracy at low gold values. X-ray fluorescent analysis Two methods of XRF instrumentation have been used with limited success. The first type is a laboratory instrument employing L X-rays. Small samples of a few grams, which are not representative,

Jan 1, 1988

By José Wilmar Calderón-Hernández

Aços inoxidáveis supermartensíticos (AISM) são aços de matriz martensítica contendo baixos teores de carbono, abaixo de 0,03%. Eles vêm sendo utilizados na indústria de óleo e gás para aplicações específicas que exigem resistência mecânica aliada a moderada resistência à corrosão. Após serem temperados para a obtenção da estrutura martensítica, esses aços são submetidos a tratamento de revenimento para alívio de tensões e melhoria das propriedades de tenacidade e ductilidade. Durante o revenimento é esperada a ocorrência de mudanças microestruturais resultantes principalmente da precipitação de diferentes fases. Tais precipitados influenciam tanto as propriedades mecânicas finais quanto a resistência à corrosão desses aços. Nesta pesquisa foi avaliada a resistência à corrosão por pite de dois AISM do tipo 13Cr5Ni2Mo, um deles contendo Nb (0,11%), através de ensaios de polarização potenciodinâmica em soluções de 0,6M NaCl sem e com adições de 0,3M e 0,6M Na2SO4. Os resultados mostraram que a adição de Na2SO4 no eletrólito contendo NaCl inibe consideravelmente a corrosão por pite. Foi constatado também que o AISM contendo Nb apresenta maior resistência à corrosão por pite nos eletrólitos de misturas de cloreto e sulfato. Além disso, os resultados mostraram que o revenimento a 575°C melhora a resistência à corrosão por pite, comparativamente ao revenimento a 600°C. O melhor potencial de pite foi obtido para o aço ao Nb, revenido a 575°C por 2h, em eletrólito 0,6Na2SO4+0,6NaCl.

Jan 16, 2018

By José Britti Bacalhau

Na conformação de plásticos de alto desempenho, cuja demanda cresce continuamente nos setores automotivo e de eletrodomésticos, é necessário aços com elevada resistência mecânica e excelente polibilidade. O aço DIN 1.2711 e suas modificações são materiais encontrados no mercado que atendem tais necessidades, porém não foram projetados para essa aplicação. O presente trabalho discute as características de um novo aço desenvolvido especificamente para moldes plásticos de alto desempenho. Foram produzidos em escala piloto, dois lingotes de 55 kg, sendo um deles o DIN 1.2711 que serviu de referência, e o outro com a nova composição química. A curva TRC dos materiais foi determinada por dilatometria, e sua usinabilidade avaliando o volume de material removido em relação ao desgaste da ferramenta de corte em fresamento. Caracterizações microestruturais por MO, MEV e dureza também foram realizadas. O Novo Aço apresenta elevada homogeneidade microestrutural e de dureza, boa temperabilidade e usinabilidade superior ao DIN 1.2711. A segunda etapa constou na produção de um bloco forjado em escala industrial a partir de um lingote de 35 toneladas, e na validação dos dados experimentais em empresas fabricantes ou usuários de moldes, as quais comprovaram a superior usinabilidade do Novo Aço em aproximadamente 50% ao DIN 1.2711. Devido à boa combinação de propriedades de manufatura o Novo Aço se torna uma interessante opção para o aumento da competitividade das ferramentarias e usuários finais de moldes plásticos.

Aug 16, 2017

By João Francisco Batista Pereira

Nos últimos anos a indústria automotiva tem evoluído de forma significativa em relação à preservação ambiental (redução da emissão de CO2) e com respeito à segurança veicular. A Usiminas, alinhada com esse direcionamento, tem realizado diversos estudos visando obter novos produtos de alta resistência mecânica que possibilitem a redução do peso dos veículos e diminuição do consumo de combustível, além do aumento da segurança. O aço TRIP, desenvolvido e recentemente comercializado pela Usiminas, é um exemplo dessa nova geração de produtos avançados, que conciliam alta resistência mecânica e alta capacidade de conformação. O trabalho apresenta as características do aço TRIP desenvolvido pela Usiminas assim como os resultados de aplicação em peças automotivas da Fiat Chrysler Automobiles.

Aug 16, 2017

By MARCELO TADEU TOMAZELA LIMA

Os aços inoxidáveis são largamente utilizados nos mais diversos segmentos da sociedade, tendo como principal característica a resistência à corrosão. Existem muitos estudos sobre o comportamento destes aços, que se apresentam com diferentes composições, estruturas e propriedades, mas algumas características ainda precisam de muito estudo, como exemplo a interação do metal com o hidrogênio. O hidrogênio nos metais é estudado há muitas décadas pela sua alta capacidade de mobilidade intersticial, todavia seus mecanismos de fragilização são pouco compreendidos e propostos em algumas teorias. O presente trabalho busca caracterizar os efeitos do hidrogênio em um aço inoxidável ferrítico tipo AISI 409 quando tensionado em ensaios de achatamento comparativamente entre amostras hidrogenadas e não hidrogenadas. Os testes no material de base evidenciaram que o hidrogênio age na perda de ductilidade deste aço inoxidável, apresentando facetas de clivagem ao ser tensionado. Os resultados obtidos sugerem que a fragilização por hidrogênio representa um risco e um desafio à Indústria, reforçando a necessidade de desenvolvimento de pesquisas e estudos para minimização dos efeitos do hidrogênio nos metais.

Oct 30, 2017

By Alexandre de Freitas Gomes de Mendonça

São crescentes as exigências por confiabilidade nos processos siderúrgicos. Nesse contexto, a Usiminas tem direcionado esforços em suas aciarias na busca da melhoria contínua dos processos garantindo a maior estabilidade operacional. O lingotamento contínuo é responsável pela solidificação controlada do aço líquido. A solidificação inicia-se no molde pela formação de uma pele que sustenta o núcleo líquido ao longo da máquina. O rompimento dessa pele representa um dos maiores problemas no processo de lingotamento contínuo por vazar o aço líquido no interior do veio e atingir as partes eletromecânicas da máquina. Essa ocorrência oferece risco de dano às pessoas, promove a interrupção do lingotamento no veio, sucateamento de produtos e indisponibilidade momentânea do equipamento. Visando reduzir a frequência de rompimentos, a Usiminas repotencializou o sistema de exaustão de vapor, adequou o sistema de detecção de rompimento de pele e criou uma equipe multidisciplinar para análise de cada evento. Essas ações reduziram significativamente a frequência dos rompimentos de pele na Aciaria 2 da Usina de Ipatinga, a ponto de registrar 539 dias sem esse evento.

Aug 17, 2017

By W. J. Witte, M. K. Witte

"INTRODUCTION A pilot heap leach project was conducted on the B. P. Selco Hope Brook ore located in southwestern Newfoundland. The pilot heap leach was undertaken to assess and confirm the following:1) To confirm that heap leach technology now currently used in the United States could be applicable to Canadian sites.2) To confirm gold recovery by the Heap Leach technology3) To assess and study potential heap leach environmental concerns in cold and wet climate.PROJECT LOCATIONThe Hope Brook Project is located near the southern coast of the island of Newfoundland, approximately 100 kilometers southeast from Stephenville, approximately 25 kilometers west of Burgeo, Newfoundland. Access to the property is limited to helicopter, float plane or by sea through Couteau Bay. The property was covered with muskeg and very few trees. Surface relief was moderate with many poorly drained boggy sections confined to small areas. Many small unnamed lakes were located on the property which provided water to small brooks and streams flowing to Couteau Bay.Several locations were reviewed for the installation of the pilot heap leach facility. Important parameters used to select a suitable location included sufficient land area, close proximity to but not on the ore body, reasonable protection from wind, sufficient supply of fresh water, close to a suitable location for a portable crushing plant, reasonable access to aggregate material for preparation of the test pad and ponds and suitable contours to minimize site preparation."

Jan 1, 1987

By G. W. Thompson

G. W. THOMPSON,* Brooklyn, N. Y.-This subject has two aspects, neither of-which can be ignored: these are the economic aspect and the technical aspect. Under ordinary conditions, economic law will take care of the conservation of tin. Under present conditions it seems desirable that economic law should still be permitted to operate as far as is practicable. It is true that this law operates rather slowly, and that under war conditions it cannot be depended upon to give our Government the supply it immediately needs. There should, therefore, be a designation of the essential industries by the Government, and tin should be supplied for those needs, letting the non-essential industries take what is left. At the same time, information ought to be forthcoming as to how tin can be conserved; with tin selling at 80 c. per pound, more or less, it is to the interest of every consumer to get the best information he can as to how he can save tin. Economic law would properly punish those who do not study their own interests in this way. I deprecate, therefore, any centralized socialistic effort toward avoiding penalties through failure to observe and obey economic law. In saying this, however, I am not unmindful that it is desirable for our Government to take such control of the tin situation as may be necessary to the prosecution of the war, practically regardless of the effect of such action upon individual industry, which should studiously seek to adjust itself to the new condition. The Government should promulgate such technical information as it can collect, showing how tin can be conserved, and should urge upon every consumer the exercise of his common sense in self-protection. There is very little danger of any one attempting to hoard or corner tin, in the present state of the market. Most consumers will be glad to live from hand to mouth, covering their sales by purchases, or vice versa. As to the technical aspects: Tin and tin alloys are used to give certain practical and also certain artistic results. The practical factors are those involved in proper adhesion, continuity of surface, protection, the right degree of hardness, proper working qualities, etc. The artistic results are those that appeal purely to the eye or to our cultivated sense of what is desirable. There is no doubt that a great deal of tin could be saved if there were not a demand for certain pleasing effects. How can this saving be brought about? The users of tin hearing alloys are not the only ones involved in this question. The manufacturers of solder and babbitt have for a long time sought to give certain appearances to their fabricated bars and ingots in order to make them more salable. The user of a solder is very apt to judge of its working qualities by the appearance of the bar; the same thing is true with regard to babbitts. Under ordinary conditions, manufacturers are justified in trying to

Jan 12, 1918

By T. Martinez Patino

Precious metals have been sought by man through time. The search has been the cause of many historic events as well as the founding of the famous Mexican, Minion centers of Durango, Guanajuato, Zacatecas and others. Bacis, a silver - cold deposit in the State of Durango was one of the lesser known centers established during Spanish colonial times. During the past year, metal prices have suffered a substantial decline, resulting in the closure of many mines. Through astute exploration, development and exploitation of the mine, the effect of the low prices has been offset and the mine is surviving these hard times.

Jan 1, 1994

By Prasanta Paul, Aminul Islam

"Nhava Sheva (India) Gateway Terminal Private Limited proposed to construct a container terminal yard, comprising a back-up area at Jawaharlal Nehru Port Terminal (JNPT), Uran, Maharashtra. The proposed container terminal yard is located on a recent reclamation on the Thane Creek, which was developed by land-based reclamation method. The underneath soft marine clay was treated, using vertical band drains and placement of surcharge upon.Settlement of the reclamation during its construction was monitored using settlement plate installed at +4.8m CD elevation which was above the highest high water level.This paper examines the settlement behaviour of the reclamation during the ground improvement works. The geotechnical parameters are back-analyzed by the authors from the field settlement results and the concerned preloading details. The back analyzed coefficients of consolidation due to horizontal flow (Ch) are compared with laboratory determined parameters and the estimated value, using Asaoka Method (1978). The authors also studied field compression ratio [CR= Cc/(1+e0)] vs. the compression ratio determined by laboratory test using back-analysis method.1. INTRODUCTIONNhava Sheva (India) Gateway Terminal Private Limited proposed to construct a container terminal yard, comprising a back-up area of approximately 27 hectares, complete with associated buildings and services on a part brownfield/ greenfield site. The back-up area shall include a heavy duty block paved pavement with band beams for electric Rubber-Tyred Gantry Crane (eRTGC) alongwith surface water drainage system and other services including area lighting, provision of fire-fighting facilities , sources for potable water and power.Based on the Employer’s Requirement and the available geotechnical investigation report, ground improvement scheme is designed by the construction contractor. Ground improvement works included the installation of prefabricated vertical drains and subsequent placement of surcharge for accelerating the consolidation of the underlying soft marine clay."

Jan 1, 2015