Search Documents

By G. A. Walsh, M. Timm, S. M. Geerts

This paper will discuss the effectiveness and the general use of improvised shaped charges. Testing was conducted by the New Mexico Tech Student Chapter of ISEE and held at EMRTC. The first series of tests conducted was to illustrate the performance of different features of the shaped charge. A PVC pipe filled with C4 with no cavity, PVC with an unlined conical cavity, PVC with a copper lined conical cavity and no standoff, and lastly a PVC pipe with a copper lined cavity and a 1.5 cone diameter standoff.

Jan 1, 2010

By Kara A. Teacoach

Current regulations for fire suppression systems in underground coal mines to protect conveyor belt installations have been in place since the Coal Mine Health and Safety Act of 1969 was enacted. Over time, the coal conveyer equipment being used and ventilation conditions underground have changed significantly, particularly the width of the conveyor belts and the use of belt air at the face. The effect of these new conditions on the effectiveness of suppression systems during a fire is not known. The National Institute of Occupational Safety and Health (NIOSH) conducted a study to evaluate the effect of air velocity, water sprinkler activation temperature, and a limited water application time on the effectiveness of water sprinkler fire suppression systems to extinguish large-scale conveyor belt fires. The fire tests were conducted using both new and used 1.8-m-wide, fire-resistant rubber belt that met the Mine Safety and Health Administration (MSHA) flame resistant requirement specified in Title 30, Code of Federal Regulations, part 18, section 18.65 (also known as the 2G test). Tests were conducted using standard response sprinklers with activation temperatures of 68 °C and 141 °C at air velocities of 0.5 and 5.1 m/s. Two tests were conducted at both air velocities for each sprinkler activation temperature, one using a new belt and one with a used belt. The results showed that the suppression system was able to suppress the fires in ten minutes to the point that a miner could extinguish it with a fire hose. However, in several of the tests, the fire reestablished itself a few minutes after the sprinkler water supply was cut off and quickly grew out of control. This report discusses the large scale experimental configuration, the installation specifications of the fire suppression system, and the results and conclusions regarding the effect of air velocity, sprinkler activation temperature, and limited water application on the suppression system performance.

Jan 1, 2010

By J. H. Rowland, A. C. Smith, K. A. Teacoach

Current regulations for fire suppression systems in underground coal mines to protect conveyor belt installations have been in place since the Coal Mine Health and Safety Act of 1969 was enacted. Over time, the coal conveyer equipment being used and ventilation conditions underground have changed significantly, particularly the width of the conveyor belts and the use of belt air at the face. The effect of these new conditions on the effectiveness of suppression systems during a fire is not known. The National Institute of Occupational Safety and Health (NIOSH) conducted a study to evaluate the effect of air velocity, water sprinkler activation temperature and a limited water application time on the effectiveness of water sprinkler fire suppression systems to extinguish large-scale conveyor belt fires. The fire tests were conducted using both new and used 1.8-m-wide, fire-resistant rubber belt that met the Mine Safety and Health Administration (MSHA) flame-resistant requirement specified in Title 30, Code of Federal Regulations, part 18, section 18.65 (also known as the 2G test). Tests were conducted using standard response sprinklers with activation temperatures of 68° C and 141° C at air velocities of 0.5 and 5.1 m/s. Two tests were conducted at both air velocities for each sprinkler activation temperature, one using a new belt and one with a used belt. The results showed that the suppression system was able to suppress the fires in ten minutes to the point that a miner could extinguish it with a fire hose. However, in several of the tests, the fire reestablished itself a few minutes after the sprinkler water supply was cut off and quickly grew out of control. This report discusses the large-scale experimental configuration, the installation specifications of the fire suppression system and the results and conclusions regarding the effect of air velocity, sprinkler activation temperature and limited water application on the suppression system performance.

Jan 1, 2010

By Alfonso Brazzini Díaz Ufano

El presente texto señala la estrategia de la disminución del impuesto de ventas, así como el aumento a las tasas de renta dentro del desarrollo minero. Para ello, es necesario incentivar la ampliación de la capacidad instalada actual de la mediana minería a través de una ley, donde el Estado no deje de percibir súbitamente el impuesto a las ventas y pueda recuperar una parte de él por un impuesto a las utilidades cuando las empresas presentan recién sus declaraciones juradas, de forma que solicite a las empresas mineras a acogerse al sistema del pago a cuenta del impuesto a la renta en base a balances mensuales.

Mar 1, 1979

By Dinner Paredes

El presente trabajo técnico, denominado “Impulsando la competitividad minera en el Perú: La economía circular y los incentivos tributarios como elementos claves para el desarrollo de una minería sostenible”, tiene como propósito primordial analizar y resaltar la importancia que tienen los principios de la economía circular y los incentivos tributarios para promover un sector minero competitivo y sostenible en el Perú.

Sep 29, 2023

By D. Goodings, W. L. Fourney, Bonenberger, R., Uli Leiste

The problem of the maximum depth at which a mine buried in the surf zone or beach zone is a threat to landing vehicles is being studied by Naval Surface Warfare Center (NSWC), Indian Head Division, Naval Research Laboratory (NRL), and The University of Maryland Dynamic Effects Laboratory. The problem was divided into two parts: The first part involves determining how deep a pressure plate mine can be and still detect a vehicle passing over it. This requires determining the distribution of stress within dry and saturated sand when a vehicle passes over a buried mine. The results obtained from that study are presented in a related paper (1). This paper will cover the second part, which entails determining the impulse delivered to the vehicle. This is equivalent to determining the impulse delivered to a plate suspended above the detonating explosive charge and includes an investigation of the distribution of the impulse over the plate. The purpose of the research is to develop a scaling law and/or computational capability which will permit predicting impulse to be expected in the field from tests conducted in the lab. The computational effort is aimed at the development of and confidence in computer codes that can be used to predict stresses and strains in plates due to the detonation of buried mines.

Jan 1, 2004

By A. M. Salomon de Friedberg

"With respect to impurities, HBM&S' copper smelter, located in Flin Ron, Manitoba, is in an unusual position. In addition to the usual concerns, the fact that copper and zinc production at Flin Ron is closely integrated results in the unique situation where feed to the copper smelter typically contains 7% to 8% zinc. This paper discusses the ramifications to copper smelter operations resulting from the marriage of HBM&S' metallurgical plants. Distributions of impurities (specifically Zn, Pb, Ni, As, Bi, Sb, and Cd) are presented and operating practices designed to reduce the impact of impurities on anode copper quality are detailed.IntroductionHudson Bay Mining & Smelting Co. Ltd. (HBM&s), has been operating its metallurgical complex located in Flin Flon, Manitoba, since 1930. The smelter and zinc plant were originally separate entities with respect to production. The smelting operation consisted of traditional multiple-hearth roasters, a reverberatory furnace and Peirce-Smith converters. The zinc plant also utilized multiple hearth roasters and then followed with sulphuric acid leaching, purification and electrowinning. The zinc plant also recovered cadmium from a separate purification/electrowinning circuit.The two plants operated essentially independently of each other until rising zinc levels in the copper concentrate and large stockpiles of zinc-rich leach residues prompted the construction of the fuming plant in 1949. The smelter used pulverized coal to reduce zinc oxide present in the reverb slag and then captured the resulting zinc bearing fume in the fuming plant baghouse. The fume was sent to a separate ""oxide roaster"" in the zinc plant where it was first roasted to remove halogens and then leached to recover the contained zinc. This oxide fume became a major source of feed to the zinc plant accounting for roughly one quarter of the total zinc production. Furthermore, through the smelter's treatment of sulphide leach residue, both copper and zinc recoveries were improved for the over-all complex."

Jan 1, 1993

By A. M. Salomon de Friedberg

With respect to impurities, HBM&S' copper smelter, located in Flin Flon, Manitoba, is in an unusual position. In addition to the usual concerns, the fact that copper and zinc production at Flin Flon is closely integrated results in the unique situation where feed to the copper smelter typically contains 7% to 8% zinc. This paper discusses the ramifications to copper smelter operations resulting from the marriage of HBM&S' metallurgical plants. Distributions of impurities (specifically Zn, Pb, Ni, As, Bi, Sb, and Cd) are presented and operating practices designed to reduce the impact of impurities on anode copper quality are detailed.

Jun 1, 1993

Zircon producers are often required to lower impurity levels to meet customer specifications as most of these impurities adversely effect the end use. For example, zircon sand in foundry applications needs to be free of any surface impurities (eg clay, gibbsite and goethite) which otherwise could cause sintering or fusion between cast metal and the zircon mould. Light coloured ceramic grade zircon, typically low in iron oxides and titania, is preferred in ceramics applications. The presence of impurities in zircon sands is a problem in the magnetic and electrostatic separation stages of their concentration. Previous work (Aral et al, 1997) showed that impurities in zircon sand concentrates occurred in the form of stains on grain surfaces, discrete gangue minerals and in the mineral grains. The gangue minerals such as rutile, garnet, xenotime, monazite, spinels, ilmenite, and aluminium silicates in the concentrate in some cases (Aral et al, 1997) contribute significantly to the impurity content of the concentrate. A careful hand picking of the impurity grains from a Western Australian zircon sand showed that the impurity content of the concentrate could be lowered significantly as a result of the removal of the surface stained grains and gangue minerals. The hand-picked ædirtyÆ fraction, comprised about eight per cent by weight of the concentrate, and consisted mostly of iron-oxide/hydroxide-stained zircon, silica grains and rutile, and occasionally ilmenite, monazite, gahnite and other (unidentified) coloured grains. The chemical analysis of the remaining æcleanÆ fraction showed that the major impurities (Fe and Ti) were reduced significantly (Table 1). The reduction in the uranium content was about 30 per cent. The other measured impurities, P, Mg, Al, Th, and Ca remained mostly unchanged as shown in Table 1. The contribution of ilmenite to the overall iron content of æcleanÆ zircon was insignificant as it comprised about 0.1 per cent weight of the æcleanÆ zircon. Rutile was the major source of titanium contamination (about one per cent by weight). Recent work (Aral and Calle, 1999) on zircon sand concentrates from the Murray Basin showed that, under the electron microprobe, the bulk of the impurities occurred in the dark back scattered electron (BSE) regions of the zoned zircon grains. The impurity contents of the light BSE regions and unblemished (unzoned) grains were low. The impurity content in zoned zircons has been investigated on single, relatively large, crystals (McLaren, Gerald and Williams, 1994; Smith et al, 1991; Romans, Brown and White, 1975). These studies generally aimed to investigate the incorporation of U in zircon as zircon is used extensively for U-Pb geochronology owing to its relatively high content of uranium. Smith et al (1991) identified a striking difference in composition between the areas of lower (dark BSE) and higher (light BSE) average atomic number in the zoned zircon. Their work showed in particular that the zones of lower atomic numbers contained very significant amounts of trace metals such as Y, REE, Nb, U, Al, Fe, Ca, Ba and, by difference H2O. In this paper the impurity distribution in zoned zircon grains was investigated on statistically significant number of grains before and after a leach treatment. The distribution of impurities was also measured in unblemished areas to compare the results.

Jan 1, 2000

By Carlos Carnurri

A characterization of mechanical properties of fire refined copper has been done in order to link ductility with oxygen content. The results show four different copper mechanical behaviours as temperature increases, where the oxygen con- tent, as Cu20 segregated, has a deleterious effect on ductility. It is concluded that until 500 ppm oxygen content, the fire refined copper could be rolled without remelting for deoxidation. Also a subsequent cold rolling could be done without intermediate annealing.

Jan 1, 1994

By W. Petruk, D. R. Morris

"The lead concentrate produced from the volcanogenic base metal ore of Brunswick Mining and Smelting in New Brunswick contains major to trace amounts of iron, zinc, cadmium, arsenic, antimony, copper, silver, selenium, tellurium, bismuth, sulphur, tin, indium, mercury and manganese as impurities. When the concentrate is sintered some of these impurities enter a variety of oxide phases, whereas others precipitate as metals. In the lead blast furnace the oxide phases decompose and the impurities recombine 10 form new phases, most are eventually discharged to the slag. The metals of the sinter remain as metals in the lead blast furnace where even more are produced, and are discharged largely with the lead bullion,IntroductionMany lead concentrates are produced from volcanogenic base metal ores . Such ores contain a wide variety of trace minerals and trace elements , therefore, concentrate s obtained from them will contain the trace elements as impurities . The impurities in the lead concentrate from one such ore, the Brunswick No. 12 deposit of Brunswick Mining and Smelting Corporation (BM S) in the Bathurst area in New Brunswick , were studied as pan of a larger investigation that was conducted to determine the extent of chemical reactions of the sinter within the lead blast furnace(1,2) The lead concentrate was investigated to identify the host mineral s for the impurities, the lead sinter was studied to identify the host phases, and frozen products from different depths within the BMS blast furnace at Belledune, New Brunswick were studied to determine the behaviour of the impurities.T he investigation was performed by pre pa ring polished sections o f the samples and studying them with a reflecting microscope, a scanning electron microscope (SE M) equipped with a Kevex energy dispersive X-ra y analysis system, a microprobe, and a Quantimet 720 image analyzer. The samples were also analyzed by X-ray diffractometer, and individual grains were analyzed by the Debye-Scherrer X-ray powder film method."

Jan 1, 1985

By C. Pichler, C. Benigni, J. Antrekowitsch

"The recycling of steel mill dust results in zinc oxides which are sold to the primary industry in or-der to recover zinc in its metallic form. Due to the contained impurities - chlorine and fluorine - these sec-ondary oxides are usually charged into the roaster together with primary concentrates. Appearing problems in this furnace limit the application of secondary materials. Based on the zinc amount, a direct leaching, assumed that a low halide concentration is present, would be possible. To use the zinc solution directly in the electrowinning stage, the concentration of impurities, first of all iron, is limited. Iron can be found in secondary zinc oxides due to carry over during the recycling process. In order to reduce the iron content in the solution, the leaching has to be pH-controlled. This leads to a limited number of simple purification steps before the solution enters the electrolysis. Various trials were performed to evaluate the influence of temperature, time and sulphuric acid concentration on the iron dissolution. This paper deals with the results and also focuses on other impurities such as halides. Additionally, the soda washing process, usually done with secondary zinc oxides to remove most of the halides, and the challenges within this step are discussed.INTRODUCTION Recycling of steel mill dust, which is the main zinc containing residue, in the Waelz process dis-plays the common method worldwide. The product of the process is a secondary zinc oxide which is con-taminated with different elements like lead, iron and halides due to mechanical carry over or evaporation. Depending on the feeding material the concentration of each element in the dust is varying. The zinc con-tent of the product, also called Waelz oxide, lies around 65–68%. Based on these values it presents an al-ternative to the primary concentrate for the production of metallic zinc. The contained halides limit the direct utilization in the leaching stage and therefore have to be reduced. State of the art is a soda washing process but also solvent extraction gives a possibility to remove chlorine and fluorine but the desired con-centration for the electrolysis is hardly reachable (Antrekowitsch et al., 2016) Iron is present as an undesirable component of such secondary zinc oxides due to carry over. During the hot acidic leaching of the secondary concentrate, iron is dissolved too. Based on the higher electrical potential iron has to be removed before the zinc solution enters the electrowinning stage. It is usually removed by precipitation as goethite, hematite or jarosite, which is the common precipitation residue (Ismael et al., 2003)."

Jan 1, 2017

By A. V. Pavlov, A. V. Dubachev, K. L. Kossyrev

The purpose of the given research was to investigate the possibility of high-carbon ferrochromium refining to remove harmful impurities as a result of metal treatment by slag mixtures on the basis of the CaO-MgO-SiO2system. The final conclusions were drawn from experimental results. It was shown that the treatment of high-carbon ferrochromium by SiO2-MgO-CaO slag mixtures with additions of chromium sinter or iron-ore concentrate removes carbon, sulphur and phosphorus from the metal. A mechanism of phosphorus removal from a melt to a gas phase is proposed.

Jan 1, 2004

By Ramana G. Reddy

Thermodynamic modeling and experimental study on impurity capacities and their distribution between mattes or metal and slags in smelting, converting and refining of non-ferrous metals was discussed. A brief review on the recent developments in copper smelting and converting is presented. The analysis showed that, copper smelting capacity increased by a factor of 10 since 60's, smelting rate increased by a factor of more than 5 and process fuel equivalent decreased by a factor of 2. A thermodynamic model for prediction of impurities capacities in slags and their distribution in mattes and slags was developed. The impurities capacities (i.e. sulfur and arsenic) of slags were calculated a priori with no adjustable parameters using the Reddy-Blander model. The capacities predictions were made in a wide range of matte and slag compositions, PSo, and temperatures in conditions pertaining to copper and lead industrial slags. The calculated results for sulfide and arsenate capacities are in good agreement with the available experimental and industrial copper and lead industrial slags data. The sulfide and arsenate capacities in copper slags (fayalite, ferrite and olivine) and lead slags are reviewed. The application of RB model predicted ratios of O2 and S2 partial pressures in industrial copper smelting processes are discussed. Application of this model for the prediction of Sb, Bi and other impurity capacities and their distribution ratios in mattes or metal and slags, in industrial smelting and refining processes is discussed.

Jan 1, 2003

By Ramana G. Reddy

Thermodynamic modeling and experimental study on impurity capacities and their distribution between mattes or metal and slags in smelting, converting and refining of non-ferrous metals was discussed. A brief review on the recent developments in copper smelting and converting is presented. The analysis showed that, copper smelting capacity increased by a factor of 10 since 60's, smelting rate increased by a factor of more than 5 and process fuel equivalent decreased by a factor of 2. A thermodynamic model for prediction of impurities capacities in slags and their distribution in mattes and slags was developed. The impurities capacities (i.e. sulfur and arsenic) of slags were calculated a priori with no adjustable parameters using the Reddy-Blander model. The capacities predictions were made in a wide range of matte and slag compositions, Pso, and temperatures in conditions pertaining to copper and lead industrial slags. The calculated results for sulfide and arsenate capacities are in good agreement with the available experimental and industrial copper and lead industrial slags data. The sulfide and arsenate capacities in copper slags (fayalite, ferrite and olivine) and lead slags are reviewed. The application of RB model predicted ratios of 02 and S2 partial pressures in industrial copper smelting processes are discussed. Application of this model for the prediction of Sb, Bi and other impurity capacities and their distribution ratios in mattes or metal and slags, in industrial smelting and refining processes is discussed.

Jan 1, 2003

By R G. Reddy

The complexity in treating environmentally harmful impurities such as As, Sb, Bi from the base metal matte or metal in the smelting stage are responsible for the high cost of the refining process. The impurity capacities (such as arsenic, antimony and bismuth) of slags were calculated a priori using Reddy-Blander (RB) model. The capacity predictions were for a wide range of matte and slag compositions in copper smelting conditions. The calculated impurities capacities and impurity distribution ratios results are in good agreement with the available experimental and industrial slags data. The a priori knowledge of impurities is useful for reduction of energy consumption and enhanced environmental control in the current and future non-ferrous metal processes.

Aug 21, 2024

By C. J. Hartley

"Scandium oxide can be recovered as a by-product from process streams in a number of chemical and metallurgical plants including TiO2 sulphate pigment, Ni/Co laterite, zirconium oxychloride and uranium operations. The feed materials available for processing can be either mid or end of process streams containing many species in solution. This paper describes the strategies available to limit coextraction of elements into scandium containing streams from TiO2 pigment production and the removal of these elements to deliver high purity scandium oxide.A critical part of process development is to work within the constraints of the main process in terms of introducing new unit processes and producing minimal additional process intermediates and residues. This requires flexibility in designing flowsheets and plants to find novel process routes that avoid production of intermediates and/or the introduction of reagents that can compromise the main process operations.Bloom Energy has developed novel solvent extraction processes for the extraction and refining of scandium oxide that minimise impacts on core process streams within TiO2 pigment plants. The additional unit processes are designed to have minimal contact with pigment plant process streams to produce a concentrate that is refined to nominal 3N purity scandium oxide in a simple, small scale commercial plant."

Jan 1, 2016

By Keiji Toyabe

Several purifying techniques have been developed for controlling the impurity levels in the copper electrolyte at Niihama Copper Refinery. These have been carried out as follows; i ) the study of the reaction in liberation made it possible to raise the current efficiency for arsenic removal by more than 50% and to decrease generation of arsine sharply. By applying this method, a good performance was attained at commercial operation. li) the antimony in the electrolyte can be successfully removed by contacting it with activated carbon. This procedure is applicable particularly when there is a large amount of antimony in the copper anode. lli) for the nickel sulphate recovery from the electrolyte, an electric evaporating system was developed. The characteristics of this process are, capability of continuous operation with less manpower, the high recovery ratio of nickel sulphate (more than 85% as nickel) and no black acid formation in the treated solution.

Jan 1, 1987

By D. T. White

Pressure acid leaching of nickel laterite ores typically involves the production of an intermediate product that is releached and refined to pure nickel and cobalt products. BHP Billiton is developing the Ravensthorpe Nickel Project to produce up to 50,000 t/y of nickel via a mixed hydroxide intermediate, which will be refined at its Queensland Nickel (QNI) Yabulu Refinery near Townsville, Queensland. The hydroxide precipitation flowsheet has been adapted to process high magnesium ores through an atmospheric leach stage, eliminate iron(III) as jarosite and oxidise iron(II) during neutralisation. The neutralisation conditions are controlled to precipitate aluminium, chromium and silicon, and to ensure good solid-liquid separation. Soluble impurities such as magnesium are purged with the tailings stream and will be managed over the long term by crystallisation in evaporation ponds.

Jan 1, 2006

By Yuan Zeping

This paper describes the distribution and removal of the main impurities in the pyrometallurgical process ?at the Guixi Smelter. The paper discusses in detail our converting schedule?of3S-SB and injecting deeply a mixture ofNa2CO) and CaO flux into the converters to enhance impurity removal.

Jan 1, 1998