Search Documents

By James Veri, Andrew H. Stern, Gerald N. Torbert

When mining coal, the occurrence of high methane liberation rates can often overwhelm the existing ventilation capabilities of the working place and result in elevated levels of methane gas. These “gas-off/stand-by condition" events often limit the production of the section and increase the potential opportunity for the occurrence of an ignition. This paper investigates the potential effectiveness of using a continuous miner equipped with an integral dust scrubber which was modified to provide high flow rates to reduce these events during active coal mining. Work was undertaken to quantify various adaptations of the mining system, by simulating site parameters in the controlled environment of an instrumented "full-scale" test facility. Monitoring (in real-time) of velocities and gas concentrations at many fixed points was also undertaken in an attempt to learn the effective limits of the system at high release volumes of gas.

Jan 1, 1997

The longwall system with caving is the most common mining system in Polish Collieries and the extraction is carried out simultaneously on several levels and in different seams. The extent and diversity of the methane hazard occurring is strictly connected to the specific geological and gas conditions as well as to the applied mining methods. Taking these factors into consideration the following methane drainage methods are applied as additional means of combatting the methane hazard in Polish gassy coal mines: 1. predrainage by means of boreholes drilled from the surface, 2. predrainage from stone drivages and devel- opment workings, 3. degasification of coal extraction workings, and 4. degasification of sealed-off areas/old goaves. Predrainage gave satisfactory results when holes were drilled from the surface or from underground workings, but only to depths to 300 m. It was necessary to adapt methane drain- age methods to the geological and mining con- ditions as gassiness increased with depth. The results of methane capture, both pre- drainage and post drainage were obtained by investigating several gassy mines.

Jan 1, 1982

By Perry JH, King RL

The Bureau of Mines in cooperation with Kaiser Steel Corporation conducted two methane drainage studies in an advancing section of the Sunnyside No. I Mine where production was being severely hampered by methane emissions. A total of six horizontal aoreholes were completed during the studies to an average length of 291 meters. Total gas production from the boreholes as of December 1981 has exceeded 6,088,800 m3. Methane emissions into the section were reduced by 40 pct as a result of the first drainage system. The second drainage system is currently producing 11,328 m3/day from four Doreholes. Mining of the section and cementing of the horizontal horeholes is expected to begin within 2 Years.

Jan 1, 1982

By Pramod C. Thakur

Sixty countries around the world mine about 5000 million tonnes of coal annually and simultaneously produce nearly 25 million tonnes (36.8 Gm3) [One tonne of methane at a temperature of 15°C and a pressure of 760 mm of mercury has a volume of 1471 cubic meters.] of methane. Many of these coal mines are very gassy and require methane drainage prior to mining as well as during mining. In spite of significant differences in the geology and reservoir properties of the coal seams, several methane drainage techniques have found universal application. The paper describes various techniques currently in use and their efficiency in recovering methane from mines. It appears that the application of state-of-the-art techniques, developed mostly in the U.S.A., can considerably increase the efficiency of methane recovery and improve the safety of mines throughout the world.

Jan 1, 1997

By A. W. de Villiers

This paper explores the behaviour of methane in the goaf during longwall mining, together with some methods for the control of methane emissions into the goaf, the working face, and the ventilation system. Experimental work done at Twistdraai Colliery, Sasol Coal, is referred to, as well as the gas-drainage system being practised at West Cliff Colliery in New South Wales, Australia. Gas drainage is discussed briefly, and certain suggestions are made in regard to coal mining in South Africa.

Jan 1, 1989

The need to solve the problems associated with spontaneous combustion, system of ventil- ation and methane drainage in gassy coal mines has brought about the development of mining and degassing methods which has made possible up to 80% gas recovery in retreating longwalls. Beneficial results also were obtained mostly in the double or multiple-entry systems, but for single-entry systems and for a seam thickness exceeding 3 m, gas recovery rate is still very low. With some single-heading systems, such as those where a return roadway is not maintained in the goaf behind the face line, a new methane drainage technology is practiced. Attempts were made to extract methane from roof holes drilled from offsets in the ribside of the longwall block. The inclinations and lengths of the boreholes were planned and designed on the basis of the geological and mining condit- ions encountered at the time and every second hole was terminated precisely at the point where the previous hole intersected the immed- iate roof goaf area above the face. There are mathematical relations approp- riate to the design of the above drainage systems to give optimum methane recovery under the given conditions. Some examples of drainage have reached 87% recovery and have attained 94% CH4 purity.

Jan 1, 1982

By Boshou B

In China, there are approximately 3,000,000 million m3 of gas (methane) included in highly gassy mines liable to coal/gas outbursts; the amount of methane pre-drainage possible is estimated at 400,000 - 500,000 million m3. At present, methane drainage has been carried out in 110 mines with a total amount of 19,000 million m3 methane produced during the period of 198 1- 1986. The methane drainage in coal mines of China can be divided into three types: from adjacent seams, from working face seams and from goafs, all with good results. In recent years, general attention has been paid to integrating methane drainage into the mining system but methane drainage from old goafs has to some extent been developed as well.

Jan 1, 1988

By Griffiths L, Marshall P

fhis paper describes investigations into drainage of gas from the solid to control outbursts. Initial studies conducted on drainage of shear zones showed that, given enough time, these can be successfully drained. Once drained, they can be intersected and driven through without any activity of outbursts. The results of programme of investigations to determine parameters for drainage from the solid show that gas flow rates from the Bulli Seam on the average are about 2 litres/min/metre length of borehole. But when shear zones are intersected, the flow rates could be as high as 8 litres/min/ metre length of hole. Shear zones can be picked up from pressure measurements 50 - 60 m away and this could give sufficient time to drill through these zones and drain them in advance. Systematic drainage of Bulli Seam at West Cliff Colliery could eliminate or reduce frequency of outbursts considerably. At present drainage holes are being drilled systematically in the seam, with drainage installations on the surface. Gas purity of 80% methane is being delivered at the surface plant.

Jan 1, 1980

By A. P. Cook

Methane drainage on a mine-wide scale is a relatively new technology to South African coal mines. Shallow seams and apparently low methane contents have been assumed to result in less methane problems than experienced in other countries. The introduction of deeper mines however, has now resulted in methane drainage taking on a higher priority. Methane contents in the region of 12 m3\t have resulted in one colliery introducing drainage as a ventilation support. Although a low seam permeability initially indicated reduced potential for drainage, early borehole flows of 90 m3\m\year have since increased to 450 m3\m\year. Rapid inflow of methane into goafs and sealed areas from seams surrounding the main production seam at another colliery have warranted extensive evaluation of the methane properties of these seams with the projected introduction of predrainage from surface. Methane pressures in excess of 1000 kPa and contents in the region of 10 m3\t again give methane volumes suitable for drainage. Coal seam drainage ahead of mining is becoming more significant and is likely to see an increase in the near future. INTRODUCTION Methane gas is an everpresent hazard associated with underground coal mining. Safe working levels of methane in the mine atmosphere are normally maintained by ventilation practises, ensuring sufficient dilution of the gas. However in some cases the ventilation must be assisted by methane drainage, either from the mined seam, or from adjacent seams and strata, or from goafed areas. South African collieries have practised only limited methane drainage until now. Relatively shallow mining depths, and apparently low in-seam methane contents have been assumed to result in fewer problems with methane than are the normal for other countries. This is now being shown to not necessarily be the situation. Work carried out by the Coal Mining division of COMRO (Cook and Erwee, 1991) indicates South African production coal seams have very similar methane retention properties to those of coals in other countries, with seam gas contents of up to 12 m3/t. This awareness, as well as greater mining depths, and higher degrees of mechanisation, has resulted in higher priority being given to methane emission problems throughout the industry. Increased levels of safety, as well as possible commercial applications, are the main reasons for the interest now being shown in methane drainage. Not only is there possible applications in the present production coalfields, but South Africa has vast areas of coal reserves which are presently non-mineable, now being seen as possible alternative energy sources. Limited methane drainage is practised within the industry, but only on collieries that have identified specific methane problems that can be alleviated by drainage. Historically this has been restricted to surface drainage of longwall goafs, reducing emissions onto the faces. More recently, horizontal in-seam holes have been drilled, until now for bord and pillar sections, but the results are being evaluated for later application to shortwall faces. Adjacent seams pose problems at some sites and vertical and cross measure boreholes are now being considered.

Jan 1, 1993

By Regan R

Appin Colliery mines the Bulli Seam with a gas composition of 98.5% methane and 1.5% carbon dioxide. Relaxation of the strata generally occurs to below the base of the Wongawilli Seam, some 40 m below the Bulli Seam, and approxim- ately 125 m above the Bulli Seam, for longwall face widths of 135 m or more. Previous exper- ience showed that when longwall faces were mined for a distance approximately equal to the face width, the mine ventilation could not provide sufficient dilution due to methane emissions from the underlying measures. Postdraining downholes were drilled to intersect the Wongawilli Seam below the operat- ng longwall. These holes were connected to an underground to surface gas range and various suction levels were applied to improve gas drainage. The resulting gas flow rates and purity from all the downholes were regularly monitored and peak flows in some holes exceeded 160 1/sec. The surface plant drained almost 20 million m3 of gas for the period July 1981 to January 1982 at an average methane purity of approximately 70%. Distinct patterns emerged for different downholes from curves illustrat- ing their variations in flow rate with distance subsequent to passage of the longwall face. The difference between free flow characteristics and those obtained with the application of

Jan 1, 1982

By Pramod C. Thakur

Methane drainage by cross-measure boreholes on retreat longwall faces can be a viable alternative to the vertical gob degas boreholes under favorable circumstances. The research was done in a mine working Pittsburgh Coal seam in Northern West Virginia under U.S.B.M. Co-operative Agreement No. 14-09-0050-3252. The study was the first application of this technique to Pittsburgh coal seam. A total of fourteen, small diameter, inclined boreholes were drilled over a retreat longwall panel from gate roads, to intersect the overlying coal seams. All boreholes were manifolded to a pipeline and the gob gas was extracted by an exhaust fan on surface. The methane capture ratio was poor at 7 to 18% at various stages of the longwall panel. A vertical gob degas borehole captured an additional 20% gas. Poor results were due to premature failures of the cross-measure boreholes leading to air leakage. For better performance the boreholes should be drilled from a point 30 to 45 m from longwall pillar over the largest chain pillar, the standpipe should be grouted for at least 6 m, and the entry containing boreholes and the pipeline must be supported to ensure access for maintenance, and optimization of methane capture. Coursing the ventilation air around longwall such that it forces methane-migration towards cross-measure boreholes can further improve methane capture. The optimum vertical inclination is 45° ± 10°.

Jan 1, 1983

By J. Cervik, P. C. Thakur, S. D. Lauer

Methane drainage by cross-measure boreholes on retreat longwall faces can be a viable alternative to the vertical gob degas boreholes under favorable circumstances. The research was done in a mine working Pittsburgh coal seam in northern West Virginia under USBM Cooperative Agreement No. 14-09-0050-3252. The study was the first application of this technique to Pittsburgh coal seam. A total of 14 small diameter, inclined boreholes were drilled over a retreat longwall panel from gate roads, to intersect the overlying coal seams. All boreholes were manifolded to a pipeline and the gob gas was extracted by a surface exhaust fan. The methane capture ratio was poor at 7% to 18% at various stages of the longwall panel. A vertical gob degas borehole captured an additional 20% gas. Poor results were due to premature failures of the cross-measure boreholes leading to air leakage. For better performance, the boreholes should be drilled from a point 30 to 45 m (98 to 148 ft) from longwall pillar over the largest chain pillar. The standpipe should be grouted for at least 6 m (20 ft), and the entry containing boreholes and the pipeline must be supported to ensure access for maintenance and optimization of methane capture. Coursing the ventilation air around longwall such that it forces methane migration toward cross-measure boreholes can further improve methane capture. The optimum vertical inclination is 45º ± 10º.

Jan 1, 1986

By M. C. Irani, Maurice Deul, M. G. Zabetakis, T. G. Bobick

This survey was conducted to determine the magnitude of the methane emission and control problem in U.S. bituminous coal mines. The resultant data indicate that the emission rate for any given coalbed depends primarily on the coal production rate and on mine depth, as well as on the nature of the coalbed and the surrounding strata. An excellent correlation was found between (1) the methane emission rate and (2) the product of coal production rate and mine depth for the mines in the Pittsburgh, Pocahontas Nos. 3 and 4, and the Illinois Nos. 5 and 6 coalbeds. The highest total emission rates found in U.S. bituminous coal mines were as follows, in million cubic feet per day: Monongalia County, W. Va., 39; Marion County, W. Va., 30.4; McDowell County, W. Va., 13.1; Washington County, Pa., 11.9; Greene County, Pa., 11.4; Buchanan County, Va., 21.6; Jefferson County, Ala., 10.3; and Franklin County, Ill., 6.6.

Jan 1, 1972

By S. P. Banerjee

By international standards, Indian coal seams are not very gassy. In some of the major coalfields such as Singareni, Wardha, Pench, Chirimiri, Rewa and Talcher Coalfields practically no methane is emitted from the coal seams. Even in the coalfields of Ranigang, Jharia, Bokaro and Karanpura, all of which are situated in the basin of the Damodar river, only a few mines are faced with excessive gas emission problems. But the number of such mines is increasing as deeper reserves are being worked and already the exploitation of some of the best quality coal reserves in the country is held up pending measures for control of methane emission in these mines. Even in mines having no previous history of gas emission, methane has been met near dykes and faults. This was dramatically revealed by an explosion in Dhori colliery in 1965 wherein 268 persons got killed. Until that time, Dhori colliery was considered as a non-gassy mine but on that fateful day gas came to the workings through a freshly exposed fault plane. Similar incidences of ignition of firedamp in so-called non-gassy mines have also occured in the past, for example, in Chapui Khas and Samla Dalurband collieries, but the casualty figures were not as high. After the Dhori explosion, all Indian coal seams have been declared to be gassy, whether presence of methane is detected in the workings or not.

Jan 1, 1980

By S. J. Schatzel

Coal mine longwall face ventilation is an important component of the overall mine ventilation system. Increases in the production rate due to higher capacity mining equipment tend to increase methane emission rates from the coal face, which must be diluted by the face ventilation with a minimal opportunity for assistance from additional control equipment (i.e., surface boreholes). Increases in panel length, in some mines approaching 6,100 m (20,000 ft), and panel width provide additional challenges to face ventilation designs. Face ventilation can also be affected by communication with the methane-laden gob gas reservoir. Except in a two-entry system, belt air cannot be used to ventilate the face in the US, except in limited cases. This relatively recent requirement has further challenged the mining industry in maintaining adequate longwall face ventilation. To assess the effectiveness of current face ventilation practices, a face monitoring study was combined with a tracer gas test on a longwall face. The study was conducted at a US mine operating in a thick, bituminous coal seam with some self-heating tendencies. Multiple gob gas ventholes were located near the face and produced a small portion of ventilation air in their production flow. Initial results show that emission rates on the longwall face showed a very limited increase in methane concentrations from headgate to tailgate despite the occurrence of methane delays during monitoring. Increases in methane concentrations in the tailgate entry in the vicinity of the longwall face T-junction appeared to be produced primarily by gas flow from the gob, not from increased emissions from the face. Barometric pressure variations were substantial over the course of the study and varied on a diurnal basis, as is typical of many mining operations. Suggestions are forwarded for reducing longwall face methane concentrations.

Jan 1, 2012

By S. J. Schatzel, R. B. Krog, H. Dougherty

Longwall face ventilation is an important component of the overall coal mine ventilation system. Increased production rates due to higher-capacity mining equipment tend to also increase methane emission rates from the coal face, which must be diluted by the face ventilation. Increases in panel length, with some mines exceeding 6,100 m (20,000 ft), and panel width provide additional challenges to face ventilation designs. To assess the effectiveness of current face ventilation practices at a study site, a face monitoring study with continuous monitoring of methane concentrations and automated recording of longwall shearer activity was combined with a tracer gas test on a longwall face. The study was conducted at a U.S. longwall mine operating in a thick, bituminous coal seam and using a U-type, bleederless ventilation system. Multiple gob gas ventholes were located near the longwall face. These boreholes had some unusual design concepts, including a system of manifolds to modify borehole vacuum and flow and completion depths close to the horizon of the mined coalbed that enabled direct communication with the mine atmosphere. The mine operator also had the capacity to inject nitrogen into the longwall gob, which occurred during the monitoring study. The results show that emission rates on the longwall face showed a very limited increase in methane concentrations from headgate to tailgate despite the occurrence of methane delays during monitoring. Average face air velocities were 3.03 m/s (596 fpm) at shield 57 and 2.20 m/s (433 fpm) at shield 165. The time required for the sulfur hexafluoride (SF6 ) peak to occur at each monitoring location has been interpreted as being representative of the movement of the tracer slug. The rate of movement of the slug was much slower in reaching the first monitoring location at shield 57 compared with the other face locations. This lower rate of movement, compared with the main face ventilation, is thought to be the product of a flow path within and behind the shields that is moving in the general direction of the headgate to the tailgate. Barometric pressure variations were pronounced over the course of the study and varied on a diurnal basis.

Jan 1, 2017

By S. J. Schatzel, R. B. Krog, H. Dougherty

Longwall face ventilation is an important component of the overall coal mine ventilation system. Increased production rates due to higher-capacity mining equipment tend to also increase methane emission rates from the coal face, which must be diluted by the face ventilation. Increases in panel length, with some mines exceeding 6,100 m (20,000 ft), and panel width provide additional challenges to face ventilation designs. To assess the effectiveness of current face ventilation practices at a study site, a face monitoring study with continuous monitoring of methane concentrations and automated recording of longwall shearer activity was combined with a tracer gas test on a longwall face. The study was conducted at a U.S. longwall mine operating in a thick, bituminous coal seam and using a U-type, bleederless ventilation system. Multiple gob gas ventholes were located near the longwall face. These boreholes had some unusual design concepts, including a system of manifolds to modify borehole vacuum and flow and completion depths close to the horizon of the mined coalbed that enabled direct communication with the mine atmosphere. The mine operator also had the capacity to inject nitrogen into the longwall gob, which occurred during the monitoring study. The results show that emission rates on the longwall face showed a very limited increase in methane concentrations from headgate to tailgate despite the occurrence of methane delays during monitoring. Average face air velocities were 3.03 m/s (596 fpm) at shield 57 and 2.20 m/s (433 fpm) at shield 165. The time required for the sulfur hexafluoride (SF6 ) peak to occur at each monitoring location has been interpreted as being representative of the movement of the tracer slug. The rate of movement of the slug was much slower in reaching the first monitoring location at shield 57 compared with the other face locations. This lower rate of movement, compared with the main face ventilation, is thought to be the product of a flow path within and behind the shields that is moving in the general direction of the headgate to the tailgate. Barometric pressure variations were pronounced over the course of the study and varied on a diurnal basis.

Jan 1, 2018

By Roy H. Grau, John C. LaScola

This Bureau of Mines report contains a tabulation of methane emissions during 1980 for all coal mines located in the United States with emissions greater than 0.1 MMcfd. Listed for each mine are methane emission quantity, location, and coalbed. The report also compares records of 1975 and 1980 and describes relationships between emissions in 1980 and the Bureau's coalbed gas content data on 11 mines.

Jan 1, 1984

By G. W. McMahon

Following the Sago Mine accident, the U.S. Mine Safety and Health Administration (MSHA) asked the U.S. Army Engineer Research and Development Center to study several possible methane explosion scenarios in the Sago coal mine. The study used a 0.3-m (1-ft) resolution map of the mine to produce a 3-dimensional (3 D) model of a portion of the mine, including the sealed area where the explosion occurred. An advanced 3 D computational fluid dynamics (CFD) code was used to calculate the explosion pressures within the sealed area, on the mine seals and in nearby regions of the mine. Based on the best available information on methane concentrations and assumptions on homogeneity and on layering and mix composition, three separate initial conditions of methane-air concentrations and location were studied. This paper discusses the CFD modeling technique, the results of the calculations, the challenges of conducting this type of modeling and the advantages and limitations of CFD modeling of accident investigations of mine explosions.

Jul 1, 2010

By W. McMahon

Following the Sago Mine accident, the Mine Safety and Health Administration (MSHA) asked the U.S. Army Engineer Research and Development Center to study several possible methane explosion scenarios in the Sago coal mine. The study used a 1-ft resolution map of the mine to produce a 3-dimensional (3-D) model of a portion of the mine, including the sealed area where the explosion occurred. An advanced 3-D computational fluid dynamics (CFD) code was used to calculate the explosion pressures within the sealed area, on the mine seals, and in nearby regions of the mine. Based on the best available information on methane concentrations and assumptions on homogeneity and on layering and mix composition, three separate initial conditions of methane-air concentrations and location were studied. This paper discusses the CFD modeling technique, the results of the calculations, the challenges of conducting this type of modeling, and the advantages and limitations of CFD modeling of accident investigations of mine explosions.

Jan 1, 2009