Search Documents

By Rick Sarkisian, Greg Girardey, David Keech

The Conveyor Equipment Manufacturers Association (CEMA) specification B105.1 "Welded Steel Conveyor Pulleys" adequately defines pulley assembly standards for light material handling applications. However, most mining applications demand pulleys of higher reliability and load capacity than that offered by CEMA standard pulleys. Various sources have published specifications for "Engineered" conveyor pulleys. Typically, these specifications require T-section type pulleys applicable to operating belt tensions exceeding 439 N/mm (2,500 lb./in.). This paper examines the application of CEMA standard pulleys, T-section pulleys and also a mining duty pulley design. The mining duty pulley fills the void between CEMA standard pulleys and T-section pulleys and can eliminate the high cost and long lead times associated with T-section type pulleys.

Jan 1, 1998

By Thomas J. Martin, James W. Martin, Paul F. Martin

The conveyor belt is the basic building block of a broad range of material handling applications in modern mining systems. The mining plans and site conditions dictate basic system requirements but this is only a part of total design evaluation. The total system in the typical mining situation can encompass all the activities from the excavators at the mining face to the processing plant, site loadout facilities and/or a power plant. The number of alternative configurations which must be evaluated including subsystems and components is limited only by analytical time and creativity. The constraints and issues which must be addressed continue to expand, driven by reliability, environmental impact and cost competitiveness. All of the system requirements must be translated into specifications for costing, final design and construction.

Jan 1, 1993

By M. C. Dow

INTRODUCTION BELT conveyors generally are conceded to be the most economical method yet devised for the transportation of large quantities of bulk materials within plants. Belts are coming into greater use for transportation over long distances and are replacing other forms of long-haul conveyance. It is not the intent of the writer to comment on the design of belt conveyors, but to offer some suggestions for improvement in the operation of conveying belts, based on many years experience with belts in several stonecrushing plants. It is the contention of this writer that opportunities for improvement not fully realized by most operators exist in many plants and that a study of the individual conveyors can result in lower unit belt costs. GENERAL RELIABILITY It is the fool-proof nature and general reliability of the belt conveyor that is responsible for its neglect. Even when abused, a belt will carry large tonnages and last a long time, often outlasting the personnel responsible for its care. Some operators look upon the purchase of a new belt as an expensive outlay every so many years, rather than a constant and steady cost amounting in belt wear alone to several dollars every operating day. This belt wear for all conveyors in one stone-crushing plant known by the writer costs 1 1/2 cents per ton or $12 to $15 per hour, based on the present cost of belt replacements. The fact that these replacement costs are double those of prewar quality emphasizes the necessity of improving the conditions that make belts wear out. Some of those conditions are the responsibility of the conveyor designer, and if a serious original error has been made, this handicap cannot be overcome by the operator. If the belt is too narrow, too steep, or too fast for good loading, the operator finds that he has an inherently expensive belt. The other factors that decrease the life of a belt are more or less under his control. The two factors of most importance are the loading conditions and the alignment. Most of the cover wear and carcass cutting occurs at the loading point and if the alignment is not good under all conditions, edge wear or damage may result, Fig I. LOADING THE BELT It is difficult to load a belt in an ideal manner; that is, to flow the material on the moving belt at a steady rate, without impact, without turbulence, and with a velocity equal to and in the same direction as the belt. An inclined belt is especially difficult to load and particularly when its speed is over 300 or 350 fpm. Inclined conveyors require longer skirt plates to prevent spillage until the load settles. It does not seem reasonable to expect an inclined conveyor to carry the same load as a horizontal belt of the same width and speed, because of the difficulty in loading

Jan 1, 1947

By Vernon R. Shorter, Wayne N. Clark

Introduction Coal is the US's largest indigenous fossil fuel resource and is used to power 57% of this country's electrical generation (NCA, 1986). Congress, however, is focusing its attention on the acid rain issue and public sentiment is leaning toward further curtailments of SO2, NO, and particulates from utility and industrial coal-burning facilities. The Cool Water plant has proven that integrated-gasification-combined-cycle (IGCC) technology can reliably produce economical electrical power while limiting SO2, NOx, and particulates to a rate of only one-tenth of the federal New Source Performance Standards for coal-fired plants. Process water requirements at Cool Water are 40% less than those of a conventional coal-fired utility plant equipped with flue-gas desulfurization units for stack gas scrubbing, thus reducing waste water treatment requirements (Clark and Shorter, 1985). The IGCC technology employed at Cool Water has now been demonstrated to efficiently convert coal to electricity in an environmentally superior fashion. The Cool Water Coal Gasification Program is an unincorporated California association of six partners whose commitment is proving that the integration of gasification with combined cycle power production (IGCC) is commercially viable and environmentally safe. The 120 MW Cool Water plant began commercial production on June 24, 1984. The Program is operating it for a five-year commercial demonstration period. The Program is about halfway through this period. Much of that which was intended to be proven is now fact. In this mid-term assessment, the authors report that the com-

Jan 2, 1987

By E. Mokgwamme, T. Goff, M. Mvalelwa, P. Spratt, P. Bezuidenhout, P. Nkosi, H. Joubert, G. de Villiers

Sibanye-Stillwater recently completed a partial sidewall rebuild on Furnace 1 at its Marikana smelter complex. The project involved matte taphole maintenance, which required the removal and subsequent replacement of 18 composite copper-graphite coolers and a section of the lower refractory sidewall. These composite copper-graphite coolers are a newly developed cooling design by Tenova Pyromet, and this rebuild project provided valuable insight into the performance of the composite coolers. The novel composite cooler design was implemented to serve as a safeguard against localised wear and corrosion in the furnace sidewall, particularly at the slag-concentrate interface, where chloride-accelerated sulphidation has been identified as a dominant degradation mechanism affecting the copper cooling elements. The composite cooler design is unique in that all the exposed sides of the water-cooled copper elements are fully encapsulated in graphite, which protects the copper from corrosive sulphur- and chlorinebearing gases and condensates. This sidewall cooling system was designed to improve corrosion resistance, stabilise freeze lining formation, and extend the campaign life of the furnace sidewall. The partial sidewall rebuild was executed during a planned maintenance shutdown with the main objective of replacing the matte taphole lintel bricks. This paper serves as a case study that compares and evaluates the operational performance of the composite coolers before and after the rebuild. The installation method is discussed to highlight the approach taken to ensure a sound installation while minimising downtime, as well as to present some lessons learned in the process.

Mar 6, 2026

By F C. D Michelin

As mines get deeper, the critical underground temperature limits will be exceeded, and an increasing number of mines will need to implement, expand or modify cooling systems. Surface cooling plants have many advantages over underground cooling such as efficient heat rejection, and lower relative capital cost; however the delivery of cooling through long underground distances can result in lost refrigeration capacity before the chilled air reaches the areas it is needed most. Refrigeration plants are therefore often overdesigned in size and capacity to compensate for underground losses.More mines are now utilising real-time monitoring and automated control of ventilation airflow and fan systems to ensure the conditions underground are safe and productive, and power consumption is efficiently managed. There may be significant opportunities to extend ventilation monitoring and control into the refrigeration delivery and control system.Energy reduction is an effective way to reduce costs and CO2 emissions, which is an increasingly important part of corporate governance. More efficient refrigeration control is a further step toward reducing energy consumption. This paper looks at an added step in how real-time monitoring can assist in controlling the output and chilled air delivery of a cooling plant. The requirements, implementation, benefits and challenges will be discussed.

Oct 12, 2022

By B Belle, M Biffi

Cooling of coal mines in the Bowen Basin, characterised by steep geothermal gradient, is presently achieved mostly through rental surface bulk air cooling in summer months. This paper argues that future mines will be required to focus their cooling resources more intensively to manage a challenging thermal environment where virgin coal temperatures of over 50¦C at a depth of 500 m are expected. Currently, mine cooling systems are employed to maintain the wet bulb temperatures (WBT) to below 27¦C at which point the risks of heat stroke or other heat-related issues are manageable. The capacities of these systems are in the range of 6 MWR to 10 MWR. The relationship between high working temperature environments and injury frequency rates is well established. Therefore, provision of appropriate cooling strategies and understanding their optimum performance and suitability are important to Australian coal mines of the future. This paper evaluates the underground temperature profiles of deep, gassy coal mines with propensity for spontaneous combustion and proposes the long-term cooling pathways to effectively manage thermal hazards. Thermodynamic modelling is performed on a longwall face and includes air leakage effects from goaf streams at various locations along the longwall face. The strategy summarises the application of underground bulk air cooling, chilled water sprays on the shearer and the resulting temperature profiles. Considering the new mining projects planned for the Bowen Basin region, a review of implementable cooling strategies such as mid-gate mobile bulk air coolers (BACs), spot coolers, underground bulk air cooling and the use of chilled water to enhance the positional efficiency of cooling plants, are discussed in this paper. Finally, the comparison of ærentalÆ versus æownershipÆ of cooling plants is analysed as part of long-term cooling strategies.CITATION:Belle, B and Biffi, M, 2013. Cooling pathways for deep Australian longwall coal mines of the future, in Proceedings The Australian Mine Ventilation Conference , pp 223-236 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By Herbert F. ?Buck? Darling

A bridge replacement project in Rochester, NY, encountered difficulties when it was determined that rock below one pier was sloping downward toward the river at an angle of 42 degrees versus anticipated 12 degrees. Cofferdam design and construction became very difficult. The unanticipated subsurface conditions delayed the project by eighteen months and increased the cofferdam cost by almost $3.0 million ($US) when direct costs and associated delays were taken into account. The initial approach after discovery of the problem was to use the same type pier design and modify the cofferdam accordingly. This resulted in a cofferdam 12 meters (39.4 feet) deep on the shore side and 18 meters (59.0 feet) deep on the water side. The design used a master pile system to attain required wall strength and used rock anchors to prevent the cofferdam from moving toward the river. The pier foundation was then redesigned by the owner using revised seismic parameters. The original stepped footing carved into rock was replaced by caissons socketed into the rock beneath a large tremie concrete placement. The revised pier and cofferdam designs caused a shift from a mostly land based cofferdam, excavation, and rock removal project into an almost entirely water based cofferdam, caisson drilling, and tremie construction project. These design changes resulted in a reliable, safe, and unusual cofferdam and construction method. All of this was accomplished within a very narrow worksite with a railroad on one side, and the river with its public and commercial freighter traffic on the other. In addition, the existing two-leaf drawbridge was to be maintained in place which put further limitations on the water borne equipment. The engineering and construction considerations, problems, and solutions related to these cofferdams and pier foundations are presented.

Jan 1, 2013

By C. Tom Blevins

The purpose of this paper is to discuss production and roof control problems associated with directional lateral stresses in an in situ stress field and the approach that Inland Steel Coal Company made in trying to cope with them. Before proceeding, a description of the mine location, product, geology, restraints, and mine history is in order. The mine is located in Hamilton County in Southeastern Illinois. It produces a high volatile metalurgical coal and is slated to produce 2.1 MTY. Product ion is in the Illinois No. 5 seam at a depth of 930 feet, approximately 490 feet below sea level. The scam height averages from 5.5 to 6.0 feet throughout the reserves with height increasing in the eastern reserve area to approximately feet and a 5 Foot average in the West. The scam tends to dip to the North, North East, but is locally very undulating. The Galatia channel washout outlines the eastern boundary of the reserves and there is a split coal area toward the central part of the property than runs south-southeast. The top above the #5 seam is laminated medium gray shale called Dykersburg. Individual shale bedding planes vary locally From ½ to 1" in thickness to a more normal thickness of 1 to 1 ½ with some areas being interlayed by thin carboncous material. The top normally must be considered as materially competent. Even though the mine is still relatively small in area with only 1.3 million tons of total production to (late, we have encountered dense zones of slicker sides and premining, stress cracks (joints). There are also areas of siltstone, that vary from a few inches to several feet thick, and areas of rider coal, clay instrusions, and rolls. We have crossed lineament concentrations that show strong evidence of corelation to localise top problems. These are being monitored closely to see their predictability on our present and future mining conditions. The face cleat runs N 55° E and butt cleat runs S. 25° E. On a regional basis, there are several anticlinal belts that trend in a northerly direction. The one major restraint is that Inland does not own surface subsidence rights. Therefore, a partial extraction mining plan is being followed. The Holland-Gaddy formula for pillar strength design is used to calculate theortical pillar sides. When production began in March of 1979, it was noted that ground control problems occurred as we drove north entries. East-west cross cuts tended to have better working conditions. This phenomia occurred from a couple hundred feet, but seemed to dispate as we got away from the men and material shafts. Once the production shaft was connected and enough entries extended for installation of belts, ground control problems were again experienced in north-south headings. It was also observed that when mining north-south headings with east-west crosscuts, if the crosscut was driven through ahead and supported, the intersection was stable upon entry connection. This held true even where fairly extreme ground control, problems were encountered. The reverse held true. when driving east-west headings with north-south crosscuts. At this time, we started searching in earnest for a working theory to explain this roof phenomia. It also became the first step of what eventually was a four step sequence to derive a workable solu¬tion to the problem. The combination of the many geological changes and the fact that north-south condition was at times intermitent, helped to disguise the stress field. The mine also being in a fairly virgin area with no mines in approximately 25 milt, radius, meant we didn't have a reliable case history to examine. Various theories were researched before it was concluded that our primary ground control problem was a directional lateral stress Field, with the major stress axis in an east-west direction. The second stop of the procedure was then to test. mining methods and determine if these stresses could be modified to a

Jan 1, 1982

By N. A. Warner

Virtually zero gas emission smelting is promoted as a means for securing environmental advantages and the general public’s acceptance. Concerns about climate change will increasingly make it more difficult for new primary metals projects to come to fruition unless greenhouse gas emissions are decreased. Assuming a sustainable market for sulphuric acid is not locally available, the next best option is high temperature reaction of strong SO2 with limestone or dolomite. This is followed by CO2 liquefaction and disposal either underground or in the deep ocean. The Voisey’s Bay nickel project is cited as an example where appropriate location of a new smelter close to large dolomite or limestone deposits would lead to a virtually zero gas emission operation. Most of the electrical energy required for producing technically pure oxygen and for liquefying CO2 and transporting it to disposal can be derived from smelting a bulk sulphide concentrate and then reacting SO2 at high temperature. Provided the smelter gases are properly cleaned before sulphur fixation, the sulphated stone should be uncontaminated and environmentally benign and possibly of use in the building and construction industry.

Jan 1, 1999

By J. J. Bean

The development drilling program of the Copper Cities mine indicated that the molybdenum content of the ore would be about 0.011% MoS2' The molybdenum content of the Miami mine at the same time was about 0.025% MOS2' The Miami mill had a very successful molybdenum operation which used bleeder turbine steam from the Miami power plant for the steaming operation. The much lower grade of the Copper Cities ore, the absence of a source of low cost steam and the use of sodium aerofloat as the copper collector which Miami experience indicated did not respono readily to the steaming technique made very doubtful the success of a similar operation at Copper Cities. However, the relatively few pounds of copper that could be recovered from the low grade Copper Cities heads made very desirable the recovery of the molybdenwa,as a source of additional revenue. Accordingly, shortly after the Copper Cities mill began operation, a research program was instituted to develop a suitable method of molybdenum recovery. This program explored first, the successful steaming process then in use at Miami and as expected, found it unable to decompose the sodium aerofloat copper collector. The known chemical depressants were then tried without much encouragement. Finally the copper concentrate was dried, not roasted, to 2-3% mOisture and this along with sodium ferro-cyanide and cyanide resulted in sufficient copper depression that a final molybdenum concentrate containing 1.0% CU could be made. The bench scale testing was followed by pilot plant testing. Sixteen

Jan 1, 1972

By R. J. Sandberg

The Copper Creek area, part of the Bunker Hill District, Pinal County, Arizona, lies within the southwest porphyry copper province of North America at the intersection of a northwest trend and an east-northeast trend of Laramide porphyry copper deposits. The Copper Creek area has been mined and explored for copper and molybdenum since the early 1900?s. The majority of this work focused on the more than 400 surface exposed breccia bodies. In the 1960 to 1970?s deeper drilling discovered a deep porphyry copper-like setting. Redhawk Copper currently has NI 43-101 compliant resources of about 0.652 billion pounds of measured and indicated and 2.745 billion pounds of inferred copper equivalent in breccia hosted and porphyry style deposits. See Figure 1.

Jan 1, 2010

By P. M. Tyroler

Inco operates a hydrometallurgical plant to treat the residue from the pressure carbonylation process. The main constituent in the residue is cop¬per. The residue is leached under pressure in an acid sulphate solution in two stages and the copper is recovered via electrowinning. The electrowinning tankhouse is fully integrated into the overall plant flowsheet as spent elect¬rolyte is required in upstream leaching steps. In recent years, the amount of residue had increased and copper removal capacity became the rate limiting factor for the entire plant. Consequently, a major program was undertaken to upgrade the tankhouse with regards to capacity, efficiency, cathode quality, working environment and structual integrity and appearance. This paper will describe current facilities and operation, and detail progress in our up¬grading efforts.

Jan 1, 1987

By K. C. Sole, G. Robinson, M. S. Moats, W. G. Davenport, S. Sandoval

Global practice in hydrometallurgical production of copper cathode by electrowinning is reviewed, based on individual plant operating data for 2018. Data from 29 plants were collected, representing 38% of world cathode copper production. Similar surveys were carried out in 1997, 1999, 2003, 2007, and 2013. This survey includes analysis of historical and current data. Evolving trends in operating conditions and performance, as well as equipment design and process technology choices, are analysed and differences in operating practices with location are assessed. Examples of recent technology and operational choices to increase productivity, improve copper quality, and decrease electrical energy consumption are discussed. Significant project expansions, particularly in Africa, and the consolidation of numerous small Chinese operations are also presented. INTRODUCTION Global trends and operating practices in copper electrowinning (EW) in 2018 are reviewed and evaluated. Similar world and African surveys were carried out in 1997, 1999, 2001, 2002, 2003, 2007, and 2013 (Robinson, Davenport, & Jenkins, 1997; Jenkins, Davenport, Kennedy, & Robinson, 1999; Davenport, Jenkins, Robinson, & Karcas, 2001; Robinson, Garbutt, & Davenport, 2002; Robinson, Davenport, Jenkins, King, & Rasmussen, 2003; Robinson, Davenport, Moats, Karcas, & Demetrio, 2007; Robinson, Sole, Sandoval, Moats, Siegmund, & Davenport, 2013). Contributing operations included sites from the USA and Mexico (9), Chile and Peru (6), Laos (1), Kazakhstan (1), and Africa (9). Despite fewer contributions compared with past experience, this survey nevertheless represents 2018 copper EW cathode production of 1.76 Mt, or about 38% of world production of 4.64 Mt (International Copper Study Group, 2017). This drop in permission to contribute is attributed to the more competitive nature of the industry and unprecedented production pressures; furthermore, several operations in Australia have shut down, while large operations that are currently commissioning or ramping up to full production in Africa and Asia declined to participate. Of the Chinese operations, which represent an increasingly important proportion of global electrowon cathode copper, particularly in Africa, only Tenke Fungurume (Democratic Republic of Congo; DRC) participated in this survey.

Jan 1, 2019

By W. G. Davenport

Changes in copper extraction from 1960 till today are documented. The top ten changes have been: (a) replacement of reverberatory smelting by high intensity oxygen rich smelting (b) growth of the Outokumpu flash smelting to over 50% of the world's smelting capacity (c) successful development of single furnace coppermaking but only for low slag fall concentrates (d) replacement of the batch Peirce-Smith converter by continuous converting, but only in a few cases (e) increased SO2 capture throughout the industry, mainly-as sulfuric acid (f) development of low initiation temperature `big bight' Cs catalysts for treating the continuous high-SO2 strength gases from continuous smelting/converting (g) complete replacement of reverberatory anode scrap and cathode melting furnaces by the Asarco shaft furnace (h) adoption of stainless steel permanent cathodes and automated stripping technology for electrorefining and electrowinning (i) complete elimination of wire bar casting by continuous bar casting/rod rolling (j) development and adoption of extractants for turning weak impure leach solutions into strong pure electrolytes. It is postulated that the biggest possible change over the next 20 years would be complete replacement of smelting/converting by hydrometallurgical processing. However, this seems unlikely due to copper purity, precious metal recovery, and economic concerns. The increasing value of sulfuric acid to many copper companies gives chalcopyrite smelting/oxide-supergene leaching a nice synergy especially with the energy credits now coming from continuous smelters, and their acid plants.

Jan 1, 1999

By G D. Richmond, J C. Chomley

Copper has been mined intermittently at Gunpowder, north of Mount Isa, since 1927. Most ventures have had some initial success but fluctuating copper prices, the small-scale of the operations and the remoteness of the site led to closures or sale. Processing routes have included direct sale of high grade ore, flotation of oxide and sulphide concentrate, and copper cement production from mine solutions. Copper cathode has been produced by heap and in-place leaching coupled with solvent extraction and electrowinning (SX/EW). Aberfoyle Limited recently purchased the Gunpowder operation and is expanding operations. An innovative high recovery tank leaching process, including a low temperature, low pressure autoclave, has been adopted. Copper cathode will be produced from an expanded solvent extraction/electrowinning plant at approximately 45 000 tonnes per year. The combination of expanded throughput and high metal recoveries will make Gunpowder a cost competitive producer.

Jan 1, 1998

By ?. ?ivkovic

The silicate slag and copper matte that are the byproducts of smelting copper in a reverberatory furnace contain SiO2, FeO, Fe3O4, CaO and Al2O3, and Cu, Fe and S, respectively. These components influence the oxide (Cuox), sulfide (Cusul) and total (Cutotal) copper content lost in the waste slag. This paper uses multiple linear regression analysis (MLRA) to determine the degree of influence. The results of calculations obtained using MLRA were compared to actual measured results and found to have a large degree of correspondence, with the coefficient of determination R2 = 0.975. These results indicate that slag composition and copper content in the matte influence the copper losses in the waste slag with a probability of above 97%. It was determined that, of the total copper content of the slag, 74% is in sulfide and 26% in oxide form, and that this ratio is not dependent on the slag or matte composition.

Jan 1, 2010

By J. H. Puffer

The copper mineralization of the Mesozoic Passaic Formation of New Jersey is typical of copper deposits in eastern North American Mesozoic sediments. Most such deposits are located at the base of the first of several basalt flows that are interbedded with continental, red-bed sediments. The copper mineralization is similar in most respects to that of the Keweenawan Basalts of the Lake Superior area. The first basaltic flow units of the eastern North American Mesozoic basins, and the Keweenawan Basalts, are continental quartz tholeiites of similar chemical composition and copper contents. The copper minerals and associated zeolite facies metamorphic mineral assemblages of these two rock units are also approximately the same. Stoiber and Davidson (1959) suggested that Keweenawan copper was mobilized and concentrated during metamorphism. The evidence pertaining to the Mesozoic copper deposits of New Jersey is consistent with such an interpretation and also with DeVore's (1955) suggestion that ore fluids commonly arise as a result of the mobility of metals under metamorphic conditions. There is additional evidence that final metamorphic concentration of Mesozoic copper was preceded by an initial stage of hydrothermal precipitation related to fluids emitted by basaltic magma.

Jan 1, 1987

By E. D. Gardner

From the standpoint of tonnage and dollar value copper is the most important nonferrous metal mined in North America. The opening of copper mines has had an important bearing on the development and settlement of many sections of the continent. The prosperity of many of the mining States or provinces depends directly upon the copper-mining industry. Normally, about 35,000 men are employed in the copper mines, mills, and smelters of the United States. The United States is the most important producer of copper among the nations; more copper is mined in North America than in any other continent, and for many years the United States alone produced about half of the copper of the world. During the last 10 years increasing production in South America and Africa has reduced the relative importance of North America and the United States.

Jan 1, 1938

Copper nickel separation is performed by mineral processing techniques both pre and post smelting in Copper Cliff at Vale Canada?s Operations. The separation at Clarabelle Mill takes advantage of the ore mineralogy to affect a separation on the rougher concentrate where chalcopyrite and pentlandite exhibit high liberation and high recoveries thus their separation is simple although incomplete. The copper concentrate comprises only 50% of the copper in ore with the remaining copper being separated post smelting in the Matte Separation plant where the slow cooled Bessemer Matte is again treated by mineral processing operations using flotation to separate the chalcocite and heazlewoodite and magnetic separators to remove a metallic nickel alloy. This paper discusses the mineralogy, separation processes and work currently underway to improve the separation of copper from nickel in these plants.

Sep 1, 2012