Search Documents

By John W. Rold

These encompass all adverse effects of oil shale mining, processing, and ancillary developments on the environment. Specific problems concern: land, vegetation, wildlife, water, air, population growth, aesthetics and public emotion; and fall into four categories of: land, water, air and emotion. Land includes excavations, spent shale disposal, loss of vegetation and impact on wildlife and domestic grazing, plant sites, buildings and roads, necessary urbanization and the total aesthetic or visual Impact. Water considerations are: requirements for Industrial and domestic supplies, adverse effect of underground water on mining, avoidance of pollution or adverse effect on surface or near-surface water, and the utilization or safe disposal of liquids. Air problems include dust, smoke and stack gas, Public emotional problems include reaction to the above problems, and misconceptions of oil shale country and an oil shale Industry. Government and industry are aware of the problems, and are seeking solutions. Last year, the three affected states studied oil shale environmental problems and solution costs. Colorado estimated environmental costs would add approximately 7% to construction and 7% to operation. The report suggested research in: (1) Water availability and impact; (2) Disturbed lands revegetation and rehabilitation, including spent shale; (3) Environmental inventory and impact; and (4) Regional development and land use planning. Governor Love appointed a 47-person committee representing Industry, government and environmentalists to attack the problems. Research pro-posals were prepared to focus on each problem. $715,000 state, federal and industry money is being committed. Results should provide data for industrial solutions and equitable agency administration.

Jan 1, 1972

By X Sun, L B. Zhou, H Yi, X Tang, P Ning

The rapid industrialisation in China has consumed large amounts of various industrial raw materials, which has left behind large quantities of industrial solid wastes produced from the processes of mining, mineral processing and smelting. The storage of huge quantities of industrial solid wastes is an obvious risk to the environment and human well-being. As the first step to fully appreciate the scale of this risk, it is necessary to carry out research for developing a pollution source environmental risk assessment system (PSERAS), especially for the typical staple industrial solid waste (TSISW). This paper aims to discuss the frame of the PSERAS for TSISW for large scale production. This system consists of two aspects: predicted factors and accidental ones, which involve physical, chemical and biological risk assessments, on-site and during transportation process. Two analysis methods, the analytic hierarchy process (AHP) and fuzzy logic assessment (FLA) were used to handle the complexity of environment and non-quantitative data. The risk assessment system for such a complex objective is difficult and the assessment of relative factors is problematic through the usual quantitative analysis. With the proposed PSERAS, it is possible to define the risk class of pollution sources. Furthermore, the risk assessment results will be helpful to the decision-maker, especially when facing unknown risks in the environmental management of industrial solid wastes. In addition, by means of the PSERAS, risk factors can be ranked against their contributions to environmental risk, in order to calculate their relative priorities in decision-making.CITATION:Sun, X, Ning, P, Tang, X, Yi, H and Zhou, L B, 2012. Environmental risk assessment system for typical staple industrial solid wastes, in Proceedings Life-of-Mine 2012 , pp 301-304 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By Hjalmar Thiel

Since industry is progressing into the deep sea, marine scientists have expressed their concern about environmental disturbances which will be introduced by using the deep seafloor for mining metalliferous resources or as a repository for wastes. Environmental studies have been conducted on national levels and in bilateral or multilateral cooperation in the development of manganese nodule mining, as this is generally achieved in marine research. These investigations were partly large-scale and experimental approaches aiming at the assessment of the impacts expected to occur in commercial mining. The results elaborated till today and expected to be acquired in the foreseeable future may remain limited. Reliable impact evaluation will result from monitoring a Pilot Mining Operation (PMO). The lecture will present the broad outlines of a possible program and a preliminary calculation of approximate costs for such a combined industrial test and environmental monitoring event. Although the extent of necessary efforts for the environmental risks evaluation can only be estimated rather vaguely, it will become evident that the required human, technical, logistical, and financial resources to be mobilized will exceed industrial capacities and go beyond national funds. Therefore, such assessment of environmental risks is calling for broad international cooperation. While industrial developments for mining the deep sea will be ruled by competition or probably by restricted joint ventures, environmental care ranges outside competition and falls within the interest of all parties involved. Environmental studies, unlike technologies for the same function, do not primarily need duplication. International cooperation in PMO monitoring would equally well support all mining companies or consortia, it would minimize the efforts for all engaged in this challenging venture of deep-sea mining and it would maximize the precautionary discussion on and the care for the deep-sea environment.

Jan 1, 1994

By B. A. Kutlin, S. A. Ropeyko, N. A. Yurlova

"The aim of NPO RIVS research and practice activities is to minimize impact of the mineral processing plants (MPP) on environment by using new concentration methods, high-technology equipment, implementation of engineering solutions directed to reduce emission of polluting substances (PS) into atmosphere, application of low-waste technologies, decrease of water withdrawal from a surface water or groundwater source for process needs. In our studies environmental safety of mineral flotation is provided through technologies using highly selective chemicals, that leads not only to reducing reagent consumption, and production of saleable products of high content of extracted minerals, but also to reducing pollutant emissions, decreasing supply of surfactants (SAA) in natural geosystems, primarily, in ground and surface waters. Decrease of water withdrawal from a surface water or groundwater sources for process needs can be achieved by using closed circuits and waste water treatment for further use in process operations, recycled water conditioning to obtain optimum quality parameters for process operations of concentration. Concentration in water (wet processing), tailings dewatering and semidry and dry (filtration cake) stockpiling in tailing ponds, efficient dust-collecting systems contribute to pollutant emission reduction. Use of mineral wastes – concentration tailings as a source of valued components, facilitates efficient use of natural resources and reduces wastes and its impact on natural ecosystems due to smaller areas of damaged lands during waste products disposal. Process and engineering solutions of NPO RIVS that allow diminishing impact of MPP on natural environment (NE) have been implemented in mining and processing complexes of Russia, Kazakhstan, Ukraine, Kirghizia and Mongolia. Compliance with environmental safety requirements contributes to enhancement of mineral processing and sustainable mineral development.INTRODUCTION Mining and processing complexes have a significant impact on environment as a result of extraction and recovery of mineral resources, landscape changes, waste disposal and, as a consequence, pollution of soils, surface and underground water sources. Therefore, the aim of the operation of the mineral processing enterprises in its research and practical activities is to reduce impact on environment due to new beneficiation technologies, high-technology equipment, implementation of engineering solutions directed to reduce emissions of polluting substances (PS) into atmosphere, use of low-waste technologies, decrease of water withdrawal from a surface water or groundwater source for process needs. Compliance with the requirements of environmental safety encourages advancement of mineral processing technologies and sustainable mineral development. Concentration in water, tailings dewatering and semidry and dry (filtration cake) stockpiling in tailing ponds, efficient dust-collecting systems contribute to pollutant emission reduction. Use of mineral wastes – concentration tailings as a source of valued components, facilitates efficient use of natural resources and minimizes waste formation and its impact on natural ecosystems due to reduction of damaged land areas during waste disposal."

Jan 1, 2018

By Robert L. Virta

An asbestos substitute is any material that replaces asbestos in a commercial product. There are many asbestos substitutes, each with its own unique physical and chemical properties. Substitutes can be inorganic or organic, fibrous or nonfibrous, and natural or synthetic. They also can be used as a direct substitute for asbestos or as a replacement product. Probably in no other field is the diversity of substitute materials so great. The concept of asbestos substitutes is not new. The first major effort to develop asbestos substitutes was undertaken by the federal government. The United States has always been dependent on foreign sources for strategic-grade asbestos, and during World War II, the government was concerned that these supplies would be cut off. Strategic-grade asbestos was critical in many electrical and thermal insulation applications (electrical insulation, battery plate separators, flame-proof boards, insulation for rocket components, etc.). A reliable supply of nonstrategic-grade asbestos also was required for general civilian and military applications, such as in brakes, clutches, and construction materials. The government not only initiated a major search for deposits containing strategic-grade asbestos, it also funded research on synthesizing asbestos in the laboratory and developing products that did not contain strategic- grade asbestos. These efforts, as well as those conducted by the private sector, generally were unsuccessful. In the late 1960s and early 1970s, a second major effort to develop asbestos substitutes began because the general public was concerned about the health threat posed by the release of asbestos fibers during the manufacture, use, repair, and disposal of asbestos-containing products. Strict regulations covering the mining and manufacturing sector already had been enacted because of the issue of occupational exposure. The issue then became environmental exposures. Environmental regulations were enacted, and through time they became more strict. The combination of increasingly strict environmental regulation, maturing of some asbestos markets, and liability issues prompted many manufacturers to discontinue asbestos product lines or search for asbestos substitutes. As a result, asbestos usage dramatically declined from the 1970s to the present (Table 1).

Jan 1, 1994

By A Romanel, M S. Kato, M P. Piermatei, P Artioli

"Brazil is the sixth worldwide producer of aluminum and Votorantim (Metals) has been operating three bauxite open pit mines in a particular way of working. In those the deposits occur on the top of hills, under forest, coffee, eucalyptus plantation or pasture area.The deposits are not large and normally mining takes an average of two months to be completed before starting the rehabilitation process, which demands a good strategy in mining planning to achieve the production goals.The benefit function developed to select feasible areas uses, beyond production costs, fees from the owner by using their area and rehabilitation cost. Both are based on land use and occupation field survey data. In this process each area with different land use receives a specific rehabilitation cost as input into a block model.Once the selection is made the mining schedule begins, taking into consideration the following premise: the orebody needs to be mined in a short period of time because during this time, the surface owners receive from Votorantim a compensation based on the expected profits from their plantation or pasture, plus royalties related to the ore amount existing in their area.Not all operations have waste dumps. Waste is pushed down by bulldozers to the lower part of the ore border. After loading and transporting ore, the waste is handled back to the mined area to fit the topography. With this step concluded, the mined area is directed to the environmental team who, alongside university partners, develop land reclamation to return them to their owners, eg in 2011, 110 ha were rehabilitated of which 29 per cent is native forest.Votorantim closes many mined areas a year and currently the entire mine planning considers this particular way of operation, making profit with minimum interference with the community and the environment.CITATION:Artioli, P, Kato, M S, Romanel, A and Piermatei, M P, 2012. Environmental variables at bauxite mine, in Proceedings Life-of-Mine 2012 , pp 171-178 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 10, 2012

By Matthew Geary, Stephen J. Marino, Jordan A. Schreiner

"INTRODUCTION Project Overview The Southeast Collector (SeC) is a new 15km long 3.0m internal diameter wastewater tunnel designed by Hatch Mott MacDonald (HMM) that twins the existing 2.6m diameter York-Durham Sewage System (YDSS) tunnel. Both sewage tunnels are located north of the City of Toronto in Ontario, Canada. The SeC provides much needed conveyance capacity for the rapidly growing York Region population, supporting development until 2036 and increasing sewage system security (Hatch Mott MacDonald and AECOM 2011). Construction of the SeC will also permit flows of the twinned section of the YDSS to be bypassed in order to clean, inspect and carry out any essential maintenance within the YDSS tunnel. Although owned and operated by York Region, the SeC spans two regional municipalities beginning upstream from the intersection of Ninth Line and Rouge Bank Drive in the City of Markham in York Region to the downstream Finch Avenue and Valley Farm Road intersection in the City of Pickering in Durham Region. See Figure 1 for the SeC and YDSS alignment. The project includes 19 shafts and chambers with depths ranging from 8 to 48m in addition to seven facilities supporting the operation and maintenance of the sewer. The construction contract was awarded to Strabag Inc. in July 2011 for $291M CAD. Construction Management services were provided by a joint venture team of Hatch Mott MacDonald and AECOM. Existing York-Durham Sewage System The YDSS tunnel was completed in 1979 and was constructed using an open shielded TBM with ribs and lagging temporary support, followed by installation of a 380mm thick unreinforced cast-in-place (CIP) concrete final lining. The YDSS sewer system has numerous connections that accumulate flows from various urban areas within York Region. The section of the YDSS twinned by the SeC flows under gravity conditions and had been putting a strain on the municipality’s potential for population and development growth having reached its maximum capacity of 420 ML/d. According to the York Region’s Water and Wastewater Master Plan, the existing YDSS would not have been able to handle wet weather flows past 2016 (Genivar and XCG Consultants 2009). The dependability of this section of the YDSS is also of concern because it is the main and critical connection between the sewer systems upstream and the downstream Duffin Creek Water Pollution Control Plant (WPCP)."

Jan 1, 2016

By Ashis Bhattacherjee, Bijay Mihir Kunar

A literature review on quantitative analysis of mine safety studies revealed that investigators use a wide range of statistical techniques for the analysis of mine injury data. Researchers have addressed the various issues of accident causation and prevention through analysis of mine injury data collected from mines. These studies are generally based on historical accident/injury data without considering the injured person/population at risk. In this paper, a public health approach, based on scientific methods of epidemiology, is presented to address mine safety issues. Epidemiology is the scientific study of disease and injury patterns among populations in time and space. Originally, epidemiology was concerned with epidemics of communicable diseases. Then it was extended to non-communicable diseases. Safety researchers found that epidemiologic methods are the best tools for injury research, because the occurrences of injury and the occurrences of disease are quite similar. As a result, some researchers started applying this concept to injury research. This paper presents some of the techniques used in epidemiologic studies and illustrates the application of a case-control study design to evaluate the role of some risk factors associated with injuries in underground coal mines. In this study, the injured persons were identified and, simultaneously, interviews were conducted to find the significant risk factors responsible for occupational injuries in coal mines.

Jan 1, 2011

By D. Diggins

Experimental apparatus for the determination of powder wettability is described. The principle of the technique is based on the measurement of the equilibrium capillary pressure in a packed bed of particles. Both the macroscopic solid-solution-vapour contact angle, e, and the specific surface area, A(m2g-1), of the powder, can be obtained. Experiments on angular quartz particles have been performed. A wide range of situations have been covered: hydrophobic and hydrophobic particles wetted with water, a variety of organic liquids and solutions of surfactants. The results show that reliable and reproducible values for 0 and A for angular and relatively coarse powders can be obtained with the proposed equipment for advancing liquid fronts in the absence of soluble surfactants. In the latter case and for receding liquid fronts in general, only qualitative trends have been obtained.

Jan 1, 1992

By R. K. Waring

A KNOWLEDGE of the mutual liquid solubility of zinc and lead is of importance in various phases of zinc metallurgy. The determination of this solubility has been the subject of numerous investigations, but unfortunatel, the results vary widely, particularly at higher tempera-tures, and it has been impossible to decide what data are most reliable. It was decided to investigate the matter and in view of the disagreement in the published results, it was felt necessary to take rather unusual precautions to insure the reliability of the data. For this reason deter-minations were made by four different methods, and the procedures of several of the previous investigators were duplicated. The previously used methods can be divided into two classes: methods involving freezing the entire melt and taking samples of the lead-rich and zinc-rich phases in the solid state, 1,2 and methods in which the. samples are taken while the bath is liquid and at the desired temperature. 3,4 Data obtained by methods involving freezing the entire melt show much lower solubility of lead in zinc than methods in which the liquid is sampled at temperature. The latter method was used by Spring and Romanoff5 and by Hass and Jellinek.6 The results of these two investi-gations are in agreement at temperatures near the melting point but at higher temperatures Hass and Jellinek find a higher mutual solubility.

Jan 1, 1934

By John T. Crawford

Introduction Loading and hauling systems are evaluated in open pit mining for new properties, expanding existing operations, changing systems or equipment, and equipment replacement analysis. The objective of such evaluations is to determine the equipment needed to handle planned tonnages at the lowest cash flow cost. Cash flow costs are used to combine capital outlays with operating and maintenance costs. Leasing costs could be substituted for capital costs with appropriate modifications to calculation procedures. These modifications will not be covered. This chapter will describe methods of evaluating loading and hauling systems, concentrating on some of the more often raised questions concerning quantitative data. While the methods described are not the only ones in current use, they have a record of proven reliability. The shovel and haulage truck system is used In the examples because of its common use in open pit mines. In medium to large open pit mines, electric shovels and diesel-electric drive haulage trucks are normally used. The basic ideas presented in this chapter apply to all loading and hauling systems, with appropriate modifications. The process of performing a shovel and haulage truck evaluation can be time-consuming and tedious because of the quantity of data involved, but it is not particularly difficult. The examples used to Illustrate shovel and haulage truck evaluation are based on a hypothetical open pit mine operating 350 days per year producing 31 750- 000 t (35,000,000 st, 100,000 stpd) annually, of which 11 110 000 t ( 12,250,000 st, 35,000 stpd) are ore. Selection of the optimum shovel and haulage truck fleets will be shown. The principal sources of data for the examples or any other equipment evaluation are equipment manufacturers and actual operations. Whenever possible, actual operating experience should be used to verify estimates. The quantitative data presented herein are unrelated to a specific existing mining operation.

Jan 1, 1979

By D. H. Magoon

The zinc smelter of Cominco Ltd. at Trail, B.C. Is the largest In the western world. A total of 550.000 tonnes of concentrate are proceed at the smelter annually. Approximately 80% of the zinc concentrate is roasted and the remainder Is treated by aqueous oxidation preaaure leaching. The zinc concentrate roasting and sulphur dioxide gas processing plants have undergone many changes over the years. This paper describes the processes and equipment currently used for concentrate roasting, S02 gas cooling and cleaning, mercury removal, sulphuric acid production liquid S02 production, and tall gas S02 scrubbing. The recent Installation of an advanced process control system for the operation of these Integrated processes Is also described.

Jan 1, 1990

By Paul D. Tomlingson

During the next several months, SME’s E-Newsletter will feature 15 articles on maintenance management. The articles may be read online or downloaded and distributed within your organization. They will address maintenance management topics, offer guidelines to mining managers and provide techniques that the maintenance manager can use. The articles will stress equipment management, a strategy that the mining industry has accepted as a modern replacement for outdated maintenance practices. Equipment management is the mutually supportive interaction of all mine departments as they establish equipment needs, procure equipment, test, commission, operate, maintain, modify and eventually replace equipment. The successful application of equipment management principles can quickly and reliably produce cost reduction and performance improvement results while providing a dependable way of sustaining them. Equipment management embraces modern management techniques. These include reliability-centered maintenance, life-cycle costing, capital performance, the effective use of information and productive organizational models.

Jan 1, 2003

By James Douglas

For the past several years, inflation has placed increasing pressure on our economic system. The total effect of inflation is complex when combined with other factors which affect the economics of equipment. A mathematical model is described herein which can be programmed on a computer to determine the effect of inflation on economic life and profits after taxes. The computer output results in graphic plots which clearly show the relation of various percentages of inflation to life and profits. Inflation has become a common topic of conversation in the recent past. What is it and how can it be measured? What effect does increased inflation have on equipment policy? Research now in progress at the Construction Institute at Stanford University is beginning to unravel some of the mystery of inflation. As a start, let us answer the first question by defining the word inflation. The dictionary says that inflation is "an increase in the volume of money and credit relative to available goods resulting in a substantial and continuing rise in the general price level. It appears, in fact, that we are in an inflationary spiral which is "a continuous rise in prices that is sustained by the tendency of wage increases and cost increases to act on each other." 3 Inflation behaves just like compound interest. It takes more dollars of future years to buy an equal amount of a given commodity, be it a material or a service. Let us assume an annual inflation rate of 5 percent. Assume that 1Associate Professor of Civil Engineering, Stanford University, Stanford, California. 2Webster's Seventh New Collegiate Dictionary, Springfield, Mass., G. and C. Merriam Co., 1969. 3Ibid.

Jan 1, 1972

By W. D. Watson

"Early in mine development at Quintette Coal Limited major problems were encountered with the fleets of primary equipment which seriously hampered production. These major fleets (cable shovels, hydraulic shovels, hydraulic drills and electric trucks) have consequently been the focal point of maintenance efforts. Some were prototypes in the Canadian mining scene and brought with them new concerns to test their skills. The problems were studied and the category and areas which were having the greatest impact on the reliability of the equipment were determined. Once defined, priorities were established and a program was initiated which was designed to accomplish a resolution. Resulting from implementation of this systematic approach, over the past three and one-half years, the fleets are now giving good reliability and industry standard availabilities. Along with these significant achievements, cost per operating hour on some of the equipment fleets has decreased substantially and continue a downtrend through 1987. This paper identifies the problems and describes the resolutions. IntroductionIn the early years of the mine development, Quintette Coal Limited (QCL) experienced production shortfalls due to problems with the major excavator and haulage fleets. A large fleet of hydraulic excavators had been purchased, and QCL was among the first northern users of all hydraulic blasthole drills. They were also using some prototype equipment and encountered problems which were not common on other types of equipment or were unknown.Because of these unique problems and lack of experience from other mines to draw on, an analytical approach was taken to areas and associated causes of the delays affecting the availability and reliability of equipment. This was done by dividing the equipment downtime into seven classifications of delays, i.e. maintenance, electrical, hydraulic, mechanical, damage, service and preventative maintenance, and tires; and then each was expressed as a percentage of total downtime. Subsequently each of the delay classification was divided into categories e.g. electrical to six categories - wheel motors, main alternator, relays, cards, no propel, lighting and 24 V system. Then, the basis for further study had been established.From this preliminary analysis of historic records, it was possible to determine the areas which were causing the majority of the downtime. These areas were then analyzed to evaluate causes and to determine possible solutions to the problem s. This paper addresses the major fleets, their problems and eventual solutions. Plea se bear in mind that the over-all objectives were to increase physical availability and reliability."

Jan 1, 1988

By Dirk Bleazard

Barrick Goldstrike Mines is improving the reliability of mining and processing equipment through the use of failure analysis and condition monitoring activities. Program results include an increase in equipment capacity and an overall reduction in operating costs. Identifying equipment failure modes and developing associated capital asset management practices can minimize failure consequences. Successful programs have included alterations to management practices, equipment modifications, and/or the implementation of condition monitoring programs. By controlling or minimizing the effects of incipient equipment failures, corrective actions can be taken earlier in the failure cycle. This results in an associated reduction to repair costs and equipment down time. Mining companies invest in their capital assets to provide the capacity necessary to meet operational needs. Over time, functional failures occur that reduce this productive capacity. Diagnostic technologies now exist that allow the condition of equipment to be monitored. Early response to this information minimizes the effects of functional failures and restores equipment re- liability. Reliability is a performance indicator of overall equipment condition. It is most often expressed in terms of mean time between failures. When the established objectives of a capital asset management program include the maximization of this failure interval, trailing indicators, such as availability and operating cost improve. The probability of equipment failure is influenced by engineering design and operating conditions. The performance level resulting from this operating environment is expressed as "inherent reliability." Without maintenance intervention, equipment will ultimately fail to perform its intended function and become less reliable. Therefore, maintenance must be managed as the supplier of reliable operational capacity. Maintenance can only supply equipment performance that approaches the level of inherent reliability. Actually achieving inherent reliability requires that all maintenance decisions are made at the economically optimal time. Enhancing performance levels beyond inherent reliability can only be achieved by altering operating conditions or practices or through physical equipment modifications. An evolution in maintenance management philosophy has been under way since the beginning of the industrial revolution. As equipment has become more sophisticated, so have maintenance practices. At the beginning of the industrial age, equipment tended to be over designed and slow moving. The first maintenance philosophy was one of reactive maintenance. Maintenance intervals were dictated by the operational status of the equipment. As a result, production interruptions were common and capacity needs were met through an investment in redundant capital assets.

Jan 1, 1998

By N. Vayenas

Modern mines possess a wide variety of capital intensive equipment. Equipment failures and the associated down time contribute significantly to the overall maintenance, operating and production costs of a mine. Reliability investigations are becoming a standard practice, as the equipment becomes more complicated and the effective use of resources is critical for achieving higher productivity and mine safety. In view of the recent global initiative for sustainable development in the mineral industries, reliability of capital intensive machinery should be considered as a key indicator for sustainable development and growth. This paper discusses the application of equipment reliability as a sustainability indicator and proposes a methodology for its practical use. Reliability of equipment systems is useful for product life cycle assessment, mine performance measurement and evaluation.

Jan 1, 2007

By G. R. Waters

NMR360 is developing a suite of chloride-based metals extraction processes, with the first commercial operation scheduled for commissioning late in 2018. It is critical, therefore, that with the introduction of any new technology, that the circuits do not suffer from mechanical failures which will compromise the operation. Although chloride leaching is at atmospheric pressure and relatively low temperature, the main challenge is preventing corrosion, since the high proton activity makes even a small amount of acid behaves as though it were concentrated. An additional challenge in concentrated chloride circuits is the potential for solids precipitation. In this context, therefore, correct valve selection is crucial, and NMR360 has partnered with CGIS to ensure that the Severe Service Valves (SSVs) needed will perform over and above the definitions of the Manufacturers Standardization Society (MSS) of the Valve and Fittings Industry. This paper outlines what the minimum requirements are for SSVs in chloride leaching applications, drawing on five decades of industry experience from one of Canada’s leading valve experts.

By Diego José Inforzato

Hot tensile data were correlated with creep data, in Aluminum Alloy AL7475-T7351, as part of a broader research program, aiming at the validation of a methodology that proposes an equivalence between the two kind of results, for metallic materials in general. The methodology is based on a criterion that establishes correlation among the following parameters from each test: the strain rate, ultimate tensile stress, and time to reach the ultimate tensile stress, in tensile tests, are equivalent respectively to the: minimum strain rate, applied stress and rupture time, in creep tests, for a given test temperature. The present material was tested at 3 temperatures: 133,166 and 193ºC, using 3 nominal tensile strain rates in the hot tensile tests: 3.2x10-6, 1.6x10-4 and 6.4x10-3 s-1 and 9 applied stress levels in the creep tests, varying from 140 to 400 MPa. The conversion of the hot tensile data to creep-like data allowed performing the analysis of all the results together according to the traditional creep relations proposed by different authors, namely: Norton, Arrhenius, Zener-Hollomon and Monkman-Grant, with the determination of the corresponding parameters in each case. The equivalence between hot tensile and creep data is also confirmed for this aluminum alloy.

Aug 8, 2018

By Gilmar Ferreira Bataglia

The possibility of parameterization of hot tensile data together with creep data is investigated, for Aluminium Alloy 7475-T7351. This study represents part of a broader research program aiming at the validation of a methodology recently proposed for analyzing both kinds of data together, considering different metallic materials. The results presented in Part 1 of this work, were analyzed according to 4 traditional methods of the literature for parameterization of creep data, namely: Larson-Miller, Orr-Sherby-Dorn, Manson-Succop and Manson-Hafferd. The compatibility of the hot tensile test results with those of creep is remarkably good, indicating the possibility of using both kind of data together also in extrapolation schemes. The criterion proposed for equivalence between hot tensile and creep data is verified to work well also for this kind of material, under the present experimental conditions.

Aug 8, 2018