Search Documents

By Michael Gauna, Christopher Mark

"Coal bursts involve the sudden, violent ejection of coal or rock into the mine workings. They are almost always accompanied by a loud noise, like an explosion, and ground vibration. Bursts are a particular hazard for miners because they typically occur without warning. Despite decades of research, the sources and mechanics of these events are not well understood, and therefore they are difficult to predict and control. Experience has shown, however, that certain geologic and mining factors are associated with an increased likelihood of a coal burst. A coal burst risk assessment consists of evaluating the degree to which these risk factors are present, and then identifying appropriate control measures to mitigate the hazard. This paper summarizes the U.S. and international experience with coal bursts, and describes the known risk factors in detail. It includes a framework that can be used to guide the risk assessment process.BACKGROUNDCoal bursts involve the sudden, violent ejection of coal or rock into the mine workings. They are almost always accompanied by a loud noise, like an explosion, and ground vibration. Bursts are a particular hazard for miners because they typically occur without warning. During the years 2012-2014, serious coal bursts occurred at three different U.S. room and pillar mines. These events resulted in three fatalities and two permanently disabling injuries (MSHA, 2014; MSHA, 2013). In all three instances, the events occurred during pillar recovery at depths exceeding 1,000 feet (300 m). None of these three mines had previously reported a burst to MSHA. Coal bursts also occurred at three longwall mines during this same time period.Despite decades of research, the sources and mechanics of bursts are not well understood, and therefore these events are difficult to predict and control. Experience has shown, however, that certain risk factors are associated with an increased likelihood of a coal burst. A coal burst risk assessment consists of evaluating the degree to which these risk factors are present. In addition, some control techniques are effective in reducing the likelihood of an event or protecting miners from their effects."

Jan 1, 2015

By Jeremiah Cohn, Rachel L. Bauer, Catherine E. Johnson

Water is frequently used in explosive applications to increase explosive performance and reduce air overpressure. Water tamping can enhance cutting abilities of shaped charges in demolition and increase impulse of kicking or breaching charges. In explosive disposal, water is used to suppress air overpressure and reduce noise. Despite its widespread use, the specific effect of water placement, whether in front of or behind the explosive, has not been studied. This work evaluates the directional effects of water placement on blast performance using 400-gram sheet explosive charges in five configurations: no water (control), rear-only water (tamped), front-only water (pushed), water on both sides (confined), and a thin front-and-rear water layer (low mass confined) to assess reduced mass effects. Water was sealed in plastic bags and held in position with custom 3D-printed cages to ensure consistent geometry and contact. A modified ballistic pendulum consisting of a hanging steel W-beam was used to evaluate impulse transfer, with high-speed video capturing swing velocity. Air overpressure was recorded using a seismograph microphone. Rear-only water (tamping) increased beam swing velocity by 69% over the control while confinement with water on both sides increased performance by 12% at a 2:1 water-to-explosive ratio and by 50% at 4:1, though it still underperformed the tamped-only configuration. Pushed water alone did not increase beam momentum and reduced tamping effectiveness by 19% when combined. Seismograph microphone data showed that pushed and low mass confined water configurations produced some of the highest air overpressure levels (up to 139.2 dB), while tamped and control charges produced lower levels (~134–136 dB), suggesting that pushed water may amplify, rather than mitigate, air shock transmission. These findings show that water placement has a strong directional influence on blast dynamics: water behind a charge enhances energy transfer to the target, while water in front provides limited or potentially counterproductive mitigation. This study advances understanding of water–explosive interactions and will lead to more effective charge designs for breaching, disposal, and demolition.

Jan 26, 2026

By M. Fener, S. Kahraman, O. Gunaydin, M. Alber

Falling into the weak rocks category, fault breccias have extremely poor engineering properties. These pebbles typically cause issues with slopes, subterranean construction, and building projects. Professionals will benefit from the creation of some predictive models for fault breccia triaxial strength, as smooth specimen preparation is typically challenging and timeconsuming. The purpose of this study is to develop some predictive models for the differential stress (Δσ) based on physical and textural properties. Artificial neural networks were used to analyse data related to Misis fault breccia. Initially, models with moderate (noticeable, but not good) correlation coefficients were created using multiple regression analysis. After that, the regression models and three distinct artificial neuron network models were contrasted. Regression models are weaker and less trustworthy than artificial neuron network models, as demonstrated by this comparison. Pointed out is the practicality and ease of use of the artificial neuron network model with S-wave velocity and volumetric block proportion. Ultimately, it can be concluded that artificial neuron networks analysis provides a reliable indirect method for predicting the differential stress of Misis fault breccia.

Sep 1, 2025

By S. K. Oraee

Managers always look for systems with minimum hazards. The hazards create problems for performance of projects. The largest and most important hazards of working underground mine can be related to health, safety and environmental, because if one of these sectors be in hazard, maybe lead to close mine. Failure mode and effects analysis (FMEA) is a widely used quality improvement tool to identify the potential failure modes for measuring reliability of a product or a process. FMEA is performed by developing a risk priority number (RPN), which is the product of severity, occurrence, and detection ratings. On the other hand, with regard to uncertainty in the decision-making, fuzzy theory will be able to model this uncertainty. Fuzzy FMEA provides a tool that can work in a better way with vague concepts and without sufficient information than conventional FMEA. This article by using Fuzzy FMEA and based on HSE criteria evaluate hazards of Parvade No. 1 Mine in Tabas Coal Mine. The results demonstrate the most hazardous parameter is rock burst in this mine.

Jan 1, 2011

By D. W. Hayley

The rapid expansion of exploration drilling with anticipated production facilities for oil and gas in the Mackenzie Delta region of the Northwest Territories has created a demand for granular construction materials. This paper discusses the technique adopted and experience gained by the authors from several major resource evaluation programs in this remote area. The first part of the paper describes a methodology for deposit identification, logistics of helicopter and ground-based drilling operations and the sampling difficulties which are unique to permafrost: soils. The second part describes the exploitation of a large glaciofluvial deposit at YaYa Lake on Richards Island. Granular construction material is sparse in the delta region relative to projected demand. Exploitable sources of granular materials for aggregates or construction borrow are found in glaciofluvial deposits of Pleistocene age or in outcrops of Paleozoic bedrock. Glaciofluvial landforms can be located by reference to published surficial geology maps coupled with airphoto interpretation. Preliminary assessment of these features in a large region is most economically carried out during the summer months with a drill that is transportable by helicopter. Once prospective borrow pit sites are identified, a detailed ground-based winter drilling program must be undertaken to establish aggregate quality and quantity, and to provide information on natural features which could affect development. The glaciofluvial terrain has been highly modified by the formation of massive ground ice within the gravel deposits. This presents some unique pit development problems which are not encountered in a normal bedrock quarry operation.

Jan 1, 1977

By QINGXIANG CAI, Lin Li, PENG LIU, IZHAR MITHAL JISKANI, XIANG LU, Wei Zhou, YONGLI ZHOU

The concept of green mining is to improve the mining industry in a holistic way so that it is safe, efficient, and environmentally sustainable. The purpose of this study was to develop an evaluation index system of green surface mining based on the theory of green grades. The evaluation model is comprised of three attributes (safety, efficiency, and environment), nine criteria, and 35 indicators. The fuzzy comprehensive evaluation method was used to determine the weights of indicators by taking into consideration degree centrality, closeness centrality, and betweenness centrality. Findings indicate that the environment is the most critical aspect of green surface mining, followed by efficiency and safety. The top five ranked green mining success indicators were the application of new technology, starting-off-rate of equipment, science and technology input to total investment, the number of accidents (decreased), and the production (increased). It was observed that more improvements are needed to overcome water, air, waste, and sound pollution. Attention should also be paid to land reclamation and post-mining land uses, which are key factors in green mining. The proposed model can be applied to evaluate and improve the level of green surface mining in other regions. This study provides a tool for decision-makers that can offer technical assistance to green mining.

May 26, 2020

By R. P. King, M. K. McCarter, K. S. Free

Mine plans typically consider the profits and costs associated with extracting and processing minerals into marketable products. Interrelationships between mine and mill costs are often overlooked during the process of mine plan optimization. A simple and quick method for predicting milling costs for a given block would improve the planning process, especially if the procedure could be incorporated as part of routine ore grade analysis of drill core or cuttings. Incorporating milling costs as part of the mine planning process could improve overall optimization of the mine/mill combination. A method developed by the Utah Comminution Center (UCC) at the University of Utah provides a possible answer to the need for quick and reliable grinding cost estimation (King et al., 1996). Using results from single-particle impact tests, a work index, called the Utah Load Cell Work Index (ULCWI), is calculated. The potential for routine use of the new method is explored by comparing ULCWI values with corresponding Bond Work Index (BWI) values for eight mineral materials (Free, 2000).

Jan 1, 2004

By H. M. Lima, L. A. Gomiero, C. A. de Morais

ABSTRACT The Caetité-Brazil uranium facility produces approximately 400 tonnes U3O8 per year from an ore averaging 0.29% U3O8. The process steps are ore crushing, heap leaching with sulphuric acid, uranium separation and purification by solvent extraction (SX) with a tertiary amine, followed by stripping with a sodium chloride solution, precipitation as ammonium diuranate (ADU), and product drying. A change in the milling process is being evaluated to increase production and uranium recovery. Heap leaching will be replaced by conventional agitated tank leaching of the –590 µm ground ore slurry in a sulphuric acid medium. Replacement of the stripping reagent is also being considered.

Jan 1, 2012

By David H. Sanders, Ramin Motamed, Fahim M. Bhuiyan, Raj V. Siddharthan

Large-diameter drilled shafts (DS) are a critical part of a seismic-resistant system, and therefore it is important to be able to accurately model lateral resistance. To undertake the lateral load analysis of largediameter DS, a finite-difference p-y analysis program, NVShaft, is being developed at the University of Nevada Reno. Validation of the new program involved numerous p-y analyses using commercially available programs. Subsequent comparisons suggested the program's ability to yield reasonable predictions for typical diameter DS. Based on the I-15/US 95 load test program carried out in Las Vegas, NV, this study presents the evaluation of NVShaft in Nevada’s subsurface condition. Lateral load analyses of a 2 ft and an 8 ft diameter DS were attempted using NVShaft. The location of the applied lateral loads and the presence of cemented soil-layers were incorporated in the modeling. A good agreement between NVShaft prediction and the measured response was found for the 2 ft diameter DS. For the 8 ft diameter DS, a stiffer response was predicted. The inspections of the moment-curvature characteristics at different load levels suggested cracked response of the concrete due to prior axial load testing may be one of the reasons behind the deviation.

By G W. Wilson, M Aubertin

A desulfurised tailings cover was installed at the Detour Lake Mine in Ontario, Canada, to reduce oxygen penetration into the underlying sulfidic tailings. The cover ranges from one to 1.5 m in thickness and was intended to maintain high water saturation to reduce oxygen diffusion and consume oxygen by oxidation of the residual sulfide minerals. The tailings impoundment was instrumented to measure climatic parameters, water levels and water content profiles within the tailings and single-layer cover. One year of monitoring data was collected. Additional tailings samples were obtained for geotechnical and geochemical characterisation. The average grain size of the cover material was found to be coarser than the underlying tailings. Monitoring also indicated that air entry values of the cover material were lower than the tailings. Numerical modelling was conducted on the cover to predict water content profiles under varying climate conditions together with the depth of oxygen penetration and diffusive oxygen fluxes. Estimates of the diffusion coefficient and kinetic oxidation rates from field data compared well with values obtained by laboratory measurements. Numerical simulations indicate water saturations of less than 85 per cent can be expected under varying climate conditions. Predicted oxygen flux rates through the desulfurised cover over tailings with high acid potential indicate low flux rates reaching these tailings due to either consumption of oxygen by residual sulfur within the cover or saturation of the underlying tailings.

Jan 1, 2003

By B Banerjee, H Masoumi, X Shen, S Raval, D Tannant

Structural mapping of pit walls can be performed using digital images and photogrammetry software, but the performance is limited by weather and environmental conditions including dust, rain and light. On the other hand, active sensors such as terrestrial laser scanners (TLS) and total stations (TS) suffer from vertical orientation bias and occlusions when persistent discontinuities dip at the same angle as the scanner line-ofsight. The recent development of the compact light detection and ranging (LiDAR) systems has made it possible to mount these sensors on unmanned aerial vehicles (UAVs) or drones which offer the potential to overcome limitations that are inherent in existing mapping systems. This study details the research involving integration and application of an advanced UAV-LiDAR system for structural mapping of a highwall. A state-of-the art laser scanner with an inertial measurement unit (IMU) and real-time kinematic global positioning system (GPS) was integrated on to a UAV. The system was first tested in a laboratory condition. Then the UAV-LiDAR system was employed to map a highwall of a coal mine. The planned flight trajectories tested the system at variable distances from the highwall face and at various speeds. The raw data collected from individual sensors were fused, filtered to remove noise, and segmented to produce a surface scan model. Finally, the point density and surface coverage were measured using the surface scan model of the highwall. The parameters were compared with equivalent measurements computed from a reference TLS data. The study demonstrates the capabilities of a UAV-LiDAR system to generate accurate and occlusion free data for mapping highwall geological structure with very quick and efficient flights in the field. CITATION:Raval, S, Banerjee, B, Shen, X, Masoumi, H and Tannant, D, 2018. Evaluation of a UAV-LiDAR system for mapping geological structures in an open pit highwall, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 496–503 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

"A commercially available through-the-earth (TTE) communications system was evaluated at an active underground longwall mine in West Virginia. This TTE system uses electricfield (E-field) sensing to send text-based communications through two separate antenna arrays connected in parallel. Each antenna array is composed of interconnected, grounded metallic rods or other such structures. Two-way communication between subsurface locations was investigated in this study using various antenna configurations. This field study was conducted as a part of a larger multisite evaluation of available TTE systems in an effort to determine their operational sensitivities. IntroductionWireless, through-the-earth (TTE) communication technology is designed to achieve point-to-point communication through solid strata using very low frequency (VLF) and ultra-low frequency (ULF) electromagnetic waves. Using this approach, communications are established without the need for intermediary communications infrastructure. As a result, TTE systems have the potential to provide reliable, robust communications between surface and underground personnel. Exploration into the use of TTE technology for this purpose dates back to the 1920s (Jakosky and Zellers, 1924; Pittman, Church and McLendon, 1985), but U.S. permissibility requirements slowed the development of TTE equipment for widespread implementation (Durkin 1980; Pittman, Church and McLendon, 1985). One of the primary challenges in producing wireless TTE communications is the counteraction of signal attenuation when propagating through solid strata (Barkand, Damiano and Shumaker, 2006; Wadley, 1949). The long wavelengths of TTE transmissions make them well-suited for reducing the rate of attenuation. However, even when operating within the VLF to ULF range, the performance of TTE systems is still affected by geologic and anthropogenic factors (Geyer, 1973; Geyer and Keller, 1976; Geyer, Keller and Ohya, 1974; Jakosky and Zellers, 1924; Large, Ball and Farstad, 1973). Although commercially developed TTE systems have demonstrated the ability to communicate in a variety of conditions, their range and performance have been highly varied (Barkand, Damiano and Shumaker, 2006; Geyer and Keller, 1976; Geyer, Keller and Ohya, 1974; Ilsley, Freeman and Zellers, 1928; Jakosky and Zellers, 1924; Yenchek et al., 2012)."

Sep 1, 2016

By A. S. Tawadrous

This paper is an evaluation of Artificial Neural Networks (ANN) as a tool in the design of the geometry of surface blast patterns. The built model uses eight different parameters, which affect the design of the pattern. Those parameters are rock type, stratification, blasthole diameter, bench height, type of explosive, priming position, powder factor and fragmentation size required. The network was trained to predict burden and spacing of the blast pattern. The model was built and trained (back-propagation technique) using 43 case histories collected from the literature. The model has then been validated using 16 cases from operational quarries.

Jan 1, 2006

By J. M. Goris

The U.S. Bureau of Mines, in cooperation with the Homestake Mining Co., and the University of Utah, is conducting a field demonstration to evaluate the behavior of rock masses supported with cable bolts. One of two rock masses being studied is supported with both conventional and birdcage cables. This rock mass is located between the 6500 and 6650 levels of the 45-4BN stope. 21 ledge. The second rock mass is the hanging wall of the D-limb stope between the 3500 and 3650 levels near the Ross Shaft and is supported with conventional cables. The primary objectives of the project are to monitor the behavior of the two rock masses during mining using extensometers and cable support strain gauges, after which the rock will be modeled using the finite-element code UTAH III. Field data will be used to verify the modeling. In addition. a comparison between the effectiveness of conventional and birdcage cables will be made.

Jan 1, 1991

By Richard A. Thomas, III JAMES H. ROWLAND, Liming Yuan

This paper presents the results of large-scale fire experiments on evaluating the performances of carbon monoxide (CO) and smoke sensors at low ventilation velocities. Experiments using three different combustibles — conveyor belt, coal and diesel fuel — were conducted in the experimental mine at the U.S. National Institute for Occupational Safety and Health (NIOSH) Bruceton Research Facility. A total of eight sensor stations were located downstream of the fire with each station containing sensors for CO, smoke, carbon dioxide (CO2 ), oxygen (O2 ), humidity, barometric pressure and temperature, as well as two airflow sensors. The airflow velocity ranged from 0.22 to 0.26 m/s (44 to 51 fpm) in the tests. The response times were recorded for the CO and smoke sensors at each sensor station when smoke and gaseous products of combustion from each burning combustible reached the station. The response times of the CO sensors were used to determine the appropriate sensor spacing in the belt entry with a low air velocity. The performance of the smoke sensor was found to be affected by the high humidity in the experiments. The results on proper selection of sensors and the determination of sensor spacing at a low ventilation velocity can be helpful for ensuring sufficient early fire warning for underground workers, thereby improving the health and safety of miners.

By Sina Mostaghel, M. Guo, E. Klaffenbach

The current paper is focused on evaluating the behavior of copper in a copper production slag and the assessment of metal recovery possibilities. For this reason, thermodynamic calculations were carried out to determine the influence of parameters such as slag composition, temperature and oxygen partial pressure on recovery of non-ferrous elements. It was found that the formation of a solid face centered cubic (fcc) phase, mainly consisting of iron, limits the extent of reduction that can be achieved for an industrial process. However, it could be discovered that solubility of iron in the Cu-rich liquid alloy strongly depends on presence of other elements, particularly arsenic. As part of the results of this study, the solubility of Cu in the slag at onset of fcc phase formation is presented as function of temperature, oxygen partial pressure and concentration of MgO and CaO. It was concluded that lower temperature (1200°C) and higher CaO addition (16 mass-% in this study), would result in the highest achievable copper recovery from slag. INTRODUCTION Copper slag is produced as a by-product of the copper production process. The slag is still containing a high amount of copper and other valuable metals. This demands further treatment of the slag as a secondary source of metals. In addition, the physical/mechanical properties of slag allow its use in several applications such as hydraulic engineering, civil engineering, as an abrasive and many more. These applications help reducing the use of natural resources like rock and sand. By decreasing the content of heavy metals such as Cu, Pb, Zn and As in the slag, its application in abovementioned fields becomes more attractive as the probability of releasing these elements to the environment is further reduced. To develop a pyrometallurgical slag reduction process, it is necessary to understand what describes the end point of the reduction. This point is expected at maximum copper recovery without facing operational challenges. Existing literature provide some information on the effect of different parameters such as temperature or concentration of different slag formers, on solubility of copper and heavy metals in different phases. However, due to complexity of industrial slags, equilibrium experiments and accurate thermodynamic modelling are essential to be able to reliably predict the behavior of different elements in the system and determine the end-point of reduction.

Jan 1, 2019

By A. Hosseini

Full-scale rupture tests were conducted on 508 mm (20 in) diameter API X-60 5.7 mm wall thickness pipes containing either axial semi-elliptical cracks or simulated corrosion defects with equivalent depths ranging from 20 to 60 percent thickness. In the case of the cracks, the failure pressures were predicted with reasonable accuracy when considering a level 3 failure assessment diagram (FAD) procedure based on API 579, as compared to level 2 FAD, since the mechanical properties were known. In both cases, the accuracy improved for shallower cracks. Considering simulated corrosion defects, the RSTRENG approach provided more reliable results on predicting the collapse pressure. For a similar depth and profile, the cracked pipes failed at a lower pressure than those containing simulated corrosion defects of equivalent depth.

Jan 1, 2010

By Grady B. V O, Cavell K. J, Ault A. R, Newman O. M G, Malcolm J. McPhersqn

Cyclic voltammetry (CV) has been evaluated as a technique for monitoring the quality of an industrial zinc sulphate electrolyte. The basis of the method involves measuring a change in the polarisation of the zinc nucleation reaction at an aluminium surface and relating this to the impurity content and/or the overall quality of the electrolyte. Specifically, the technique aims to be able to indicate and quantify detrimental synergism between impurity elements, something which traditional analytical techniques are incapable of providing. The technique has found some success with regard to monitoring glue additions in a range of metal electrolytes. It has been found that investigations by a number of workers over the past 15 years have produced variable and often misleading results due to the inadvertent use of commercial purity aluminium working electrodes. It has been shown that impurity elements in the working electrode can give rise to a range of responses that are not obtained when pure aluminium is used and that the response is variable due to the lack of surface homogeneity of commercial purity aluminium electrodes. Furthermore, it was demonstrated that previous detection limits reported in the literature were based on the presence of additional peaks in the cathodic scan and not polarisation effects. The results of this study have shown that when a pure aluminium working electrode was used, the method was incapable of detecting any change in polarisation for an electrolyte containing three common impurities (Co, Ni and Ge), at concentrations that would significantly reduce optimum electrolytic performance. A range of methods was tried to sensitise the technique, including raising the temperature and acidity, and adding antimony in order to induce some synergism. In all cases the polarisation response was unchanged. Consequently, apart from the commercialised application for monitoring additions of antimony and levelling agents such as glue, CV has very limited application as an electrolyte screening technique.

Jan 1, 1993

By J. H. Rowland, R. A. Thomas, III, C. D. Litton

Atmospheric monitoring systems (AMS) are required when using air from conveyor belt entries to ventilate working sections in U.S. underground coal mines. AMS technology has the potential to increase fire safety mine-wide, but research is needed to determine the detection and response times for fires of a variety of combustible materials. To evaluate the potential of an AMS for fire detection in other areas of a coal mine, a series of full-scale fire experiments were conducted to determine detection and response times from fires of different combustible materials that are found in U.S. underground coal mines, including high- and low-volatility coals, conveyor belts, brattice materials, different types of wood, diesel fuel, and a foam sealant. These experiments were conducted in the Safety Research Coal Mine (SRCM) of the U.S. National Institute for Occupational Safety and Health (NIOSH) located in Pittsburgh, PA, using a commercially available AMS that is typical of current technology. The results showed that through proper selection of sensors and their locations, a mine-wide AMS can provide sufficient early fire warning times and improve the health and safety of miners.

Jan 1, 2016

By C. J. Slaughter, S. P. Harteis, L. L. Chasko, D. W. Alexander

The Department of Health and Human Services (HHS), National Institute for Occupational Safety and Health (NIOSH), Office of Mine Safety and Health Research (OMSHR), with the assistance of cooperating underground mining operations and state agencies, has conducted research exploring devices and technologies that could be used to assist miners navigating through smoke and dust resulting from a fire or explosion. Recent events in mines confirm that smoke and dust can enter and contaminate mine escapeways, creating an atmosphere with severely reduced visibility. This reduced visibility results in substantially increased escape times, possible disorientation or confusion, and increased stress levels, and may prevent evacuation altogether. Tools or devices that assist miners in navigating through smoke-filled areas void of lifelines could make the difference in successful escape from the mine. This paper presents the results of OMSHR research to identify and evaluate tools and devices that could provide meaningful information to evacuating miners in areas with limited visibility and without the benefit of a lifeline.

Jan 1, 2011