Search Documents

By Peter Moser, Mark Ganster, Andreas Gaich

Surveying of a bench face before blasting is a pre-requisite for a proper blast planning and for a satisfying blasting result both in terms of safety and fragmentation. When surveying a bench face, preferably a large amount of measurement points are required in order to determine the geometry and especially the irregularities with sufficient accuracy. Only contact-free measuring systems allow evenly distributed measurements over the whole bench surface. Existing systems such as total station, laser profiler, or laser scanner show significant drawbacks such as that surveying results are just isolated values of the bench geometry such as heights or profiles, that borehole positions have to be defined in advance in order to know where to take profile measurements and that systems require special surveying skills and that they are expensive too. In order to overcome these difficulties and to provide the blasters a simple tool for bench surveying, blast design and layout and the subsequent back-transfer of the blast plan into the quarry, the Department of Mineral Resources& Petroleum Engineering of the University of Leoben, 3G Software & Measurement company and Mineral AB, one of the largest producers of aggregates in Europe formed a joint venture to develop a new system. Based on an existing stereophotogrammetric system for rock surface surveying and joint analysis (JointMetrix), a new tool was developed within a year. Apart from several mines and quarries using that new tool already today in the daily work, both the Department of Mineral Resources& Petroleum Engineering at the University of Leoben and Austin Powder GmbH Blasting Service did a lot of studies to determine the reliability of the new stereophotogrammetric blast surveying and planning system and its precision in comparison to classical laser surveying equipment. After 1 year of testing and comparison with laser based surveying instruments, it can be concluded, that the new technology of blast surveying& design systems based on stereophotogrammetry is suitable for being used in the daily work routine in quarries and mines. The comparison of the precision of laser based systems and stereophotogrammetric systems has shown, that the deviation between these two types of systems is less than 10 cm, in many cases even lower.

Jan 1, 2007

By W. A. Jones

Purpose of Paper Geophysics is a highly developed science which has found a wide use in industry. Perhaps the most spectacular application has been in the field of oil exploration. It has been estimated that, up to the end of 1939, geophysics was responsible for the discovery of five billion barrels of oil. In 1944, the sum o $40,000,000 was expended for geophysical work in the search for new oil deposits. Although the metal mining industry has so far made comparatively little use of the science, it is becoming increasingly common for the exploration engineer or geologist to be required to co-operate with the geophysicist. Many papers dealing with applied geophysics have been published but in most of them advanced training in physics and mathematics on the part of the reader has been assumed. It is difficult for the average engineer to obtain a ready understanding of the equipment, field procedure, and scope and limitations of the science from the literature. The present paper attempts to describe briefly and in simple terms the principles underlying magnetic, self-potential, and electrical resistivity methods and their application to a field problem. Introduction Geophysics is concerned with the study of gravity, magnetism, natural earth currents, earthquakes, vulcanism, and many other natural phenomena. The methods, originally devised for the measurement, for scientific purposes, of the forces associated with such phenomena have been adapted to the search for buried deposits of economic value. If the body sought has large dimensions and distinctive physical properties, geophysical measurements may reveal associated, and in some cases quite characteristic, anomalous features. However, in many instances the mass cannot be indicated directly but has a common association with geological features which can be defined by physical measurements. Although such surveys cannot specifically identify oil, metalliferous minerals, or other commercially valuable substances, it is possible to delineate anomalous sub-surface physical features which, with the help of geological information, can be assessed as possible or probable indications of the body or structure sought. The nature and extent of the material causing an anomaly, and its economic importance, can only be determined by further exploration, such as drilling.

Jan 1, 1947

By D. C. Yates, G. V. Jolliffe

In the five coalfields of Staffordshire, there have been some 43 incidents of spontaneous fires and heatings which have required special attention in the past ten years. This total excludes incidents in the Thick Coal Seam of South Staffordshire, which was worked until 1967, and which was subject to an almost continuous series of heatings. The incidents have been classified to show the sites of occurrence, the contributory factors which may have caused them and the treatments applied to them. The remedial techniques, as practised in Staffordshire, are dealt with in detail, with particular reference to standard methods of stopping-off. Precautionary measures taken are described, including a "liability to spontaneous combustion" classification of all seams, and the setting up of an emergency organization with emergency stocks of materials and equipment. The paper is concluded by a few words on the organization and control at the time of an incident.

May 23, 1905

By R. L. Blackwood

The solid inclusion cell for absolute in situ stress measurement has been found to give reliable results in coal. The cell is described briefly, along with the methods of installing, overcoring and taking readings in underground coal mines. The validity of the cell performance is demonstrated by reference to the stress-relief curves obtained during overcoring and a three-dimensional B.I.E.M. analysis of the installation to test for stress anomalies deriving from the geometry of the overcoring groove-borehole-cell arrangement. Case studies of two stress measurement projects using the cell are presented for coal mines in New South Wales, Australia.

Jan 1, 1982

By A. Zangooi, J. A. Finch

"A frother analysis technique based on the formation of a colored solution with UV-VIS absorbance proportional to frother concentration over a certain range has been developed. The calculation of concentration requires the comparison of the sample absorbance at a selected wavelength with a linear calibration (frother concentration vs. absorbance) constructed with values collected from solutions of known concentration (standards) at the same wavelength. It has been found that concentration ranges for preparation of standards can vary widely. An integration of our experiences into a databank can offer some guidance on the selection of standard concentrations. The databank includes results from the analysis of 37 chemical reagents, commercial frothers, and natural oils used in research work or at industrial sites. Grouping frothers by similar chemical structure or origin provides a good basis for selecting the standards to approach the maximum absorbance range for the spectrophotometer in use.INTRODUCTIONA technique to determine frother concentration on samples of industrial milling streams based on formation of a colored solution with UV-VIS absorbance proportional to frother concentration has been developed. The concentration is determined by comparison of its absorbance, at some selected wavelength, with those obtained by processing a series of solutions of known concentration (standards), at the same wavelength. It is desirable to have linear calibration (frother concentration vs. absorbance) over the widest concentration range. The upper concentration can be restricted by the instrument, as there is a maximum detectable absorbance (minimum transmittance), which can be reliably sensed by the UV-VIS detector (in most cases maximum absorbance is 3)."

Jan 1, 2016

By D. V. Hughes, J. R. Nyberg

"Since 1985, a comprehensive automation system has been installed at the Outokumpu Oy Zinc Plant, Kokkola, Finland. In leaching and solution purification special sample handling equipment, on-line analyzers and instruments, and a computer-based control system with duplicated supervisory stations have been installed. The system has enabled closer control of the process and more efficient use of labor. Since its installation recovery of zinc has improved, and use of zinc dust, steam, and water have decreased. The system has performed reliably. It includes optimizing programs and process study tools, which facilitate improving process performance. An expert system has been built-up to prompt process personnel to take appropriate action on the basis of process data. In electrolysis a similar system, based on extensive monitoring of the process and of production of zinc cathodes, is used to maximize- current efficiency by maintaining optimum conditions in the process. It is planned that in the future the control systems will be integrated and extended to cover the roasting plant and effluent control.IntroductionThe Zinc PlantThe Zinc Plant of Outokumpu Oy Metallurgical Division at Kokkola, on the West Coast of Finland, has grown from a 90,000 t/a plant founded in 1969 to become, with its present capacity of 170,000 t/a, one of the world's ten largest zinc plants. Especially since the completion in 1988 of a thorough modernization programme, it is also among the world's most modern.The Kokkola plant takes its raw materials from Outokumpu's own mines, Vihanti and Pyhasalmi in Finland, and Tara in Ireland, and from outside sources. Concentrates are roasted in two Lurgi fluid-bed furnaces, and the calcine is leached and iron removed by the Conversion process. Following this copper, cobalt, and cadmium are removed, and zinc is refined by electrowinning. The leaching and purification, and the cell-house are automated under computer-based control, and anode and cathode handling in the cell-house are mechanized and fully automatic."

Jan 1, 1989

By Ingemar Hermansson, Thomas Bjerendal, Mattias Grävare, Carl-John Grävare

"AbstractHigh strain dynamic pile tests (HSDPT) on driven piles have been carried out on a routine basis in Sweden for more than 30 years. The Swedish Commission on Pile research established, in the early 1980s, safety factors based on the percentage of piles tested. The safety factors could then be reduced, creating economic incentives for the contractor to carry out testing.Energy formulas adopted by our neighbour countries, Norway and Denmark, were not accepted in Sweden as a reliable method since the dynamic testing method was considered to be a more scientific and reliable method. It has become almost the only in-situ method used to verify geotechnical bearing capacity on driven piles.The typical Swedish geology of soft soils overlaying very hard strata makes it possible to verify high design loads, typically 20 kN per cm2 of pile cross sectional area for steel piles and 1,5 kN per cm2 for concrete piles.Conventionally a certain percentage of the piles have been tested in Sweden. The EC7, on the other hand states a number of piles to be tested, regardless of the total number of piles. The Swedish NA (National Annex) states a maximum distance between tested piles, which results in better distribution of the test piles over the foundation.For shaft-bearing piles in soft clays, dynamic pile tests have to be correlated by static load tests.Historical backgroundOn a research basis stress-wave measurements have been carried out for a long time in Sweden. One example is a project in the city of Gothenburg, conducted by Fellenius and Pejrud (1964). Strain gauges were glued on the reinforcement bars in 60 m long, precast concrete piles at 3 m and 25 m above the pile tip respectively. Evaluation was done with different methods such as dynamic formulas,stress-wave measurements and in addition compared with static load tests.In the 1975 Building Code in Sweden, driving criteria for concrete piles based on stress-wave theory were introduced, as summarized in Table 1. The driving criteria are intended for 3 and 4 tonne gravity hammers. For hydraulic rigs, which have free-falling hammers, the drop height indicated should be reduced to 80 % of the values in the table. The criteria were considered to include a safety factor of 3,0. For 330 - 450 kN pile load, pile with a standard a cross sectional area of 235 mm x 235 mm was used. For 600 kN load, the standard cross sectional area was 275 mm x 275 mm."

Jan 1, 2014

By Steven D. Dapp

The use of base grouting (tip grouting) to enhance the axial capacity of drilled shaft foundations can achieve improvements in economy and reliability for many types of projects and soil profiles. Recent experiences on a range of different construction projects in the Southeastern U.S. illustrate the most attractive opportunities for utilizing this technique and some limitations of the method. The quality assurance provided by measurements obtained during post grouting the pile toe is another important aspect favoring its use; the base grouting is shown to identify weaker piles and provide a means of remediating some deficiencies so that increased foundation reliability is achieved. This paper provides an overview of the methods used to evaluate and design for base grouted shafts along with lessons learned from several case histories.

Jan 1, 2006

By Seppo] [Kreula

Outokumpu Oy has acquired considerable experience with on-stream X-ray fluorescence analyzers and with computer control of flotation processes over several years. It became evident at the outset of this work that a reliable and accurate on-stream analyzer was more than a collection of different pieces of hardware linked together. Extensive work was done to develop an integral analyzer system, beginning with process samples through the spectrometer to report typewriters, recorders and the control computer. To date, over ten Courier-300 analyzer systems based on this development have been installed world-wide, several of which provide the key information for successful computer control systems. Computer control of flotation processes has been under development at the Pyhäsalmi concentrator since 1968. Two different control strategies have been implemented. The copper flotation is controlled by means of a mathematical model and economic criteria, whereas the "evolutionary operation principle" is applied to the zinc flotation. The computer control system installed at' the Vuonos-mine has been developed according to the same guidelines. In order to consolidate this wide experience, a flotation computer control system, Proscon-100, was developed by Outokumpu Oy, and the first system was installed at Kotalahti in 1972. In addition to the technological experience, enough information has also been gathered to illustrate the economical, benefits accruing through the use of these advanced tools of automation.

Jan 1, 1973

Mining Equipment Challenges Equipment Availability Unplanned downtime Maintenance Costs Secondary damage and catastrophic failures (T282 $750k) Emergency work is 4x the cost of planned work Inspections Troubleshooting time Incorrect repairs (parts, labor, lost production) Equipment Life Mis-operation of equipment

May 1, 2013

By Kent Zehr

Suncor Energy Inc. is an integrated producer and refiner of oil and gas headquartered in Calgary, Alberta. The bulk of revenue comes from the Oil Sands Group (OSG) operating in the McMurray formation of the Athabasca Oil Sands. Located some 25 kilometers north of Fort McMurray, Suncor OSG began life in 1967 as Great Canadian Oil Sands, the first operator to successfully enter commercial production of synthetic crude oils from the area. For most of the last decade, dramatic growth has been the standard mode of operation for Suncor OSG. Production of synthetic crude first reached 100,000 barrels per day in 1997 and less than five years later is averaging in excess of 200,000 barrels per day. Within this dynamic organization, Suncor Extraction is the business unit that processes run-of-mine ore into clean diluted bitumen for Upgrader feedstock. Extraction also delivers and places the barren sand and process affected water into tailings storage in one of several ponds from which water is recycled to support the various processes. For reference purposes, Extraction on a typical day currently receives more than 400,000 metric tons of oilsand ore, which is all processed to water based slurry for separation in one of two extraction plants. Separated tailings are disposed of as a slurry and the cleaned bitumen froth is diluted with naphtha and sent to tankage for storage until required by the Upgrading Unit. As a consequence, on a typical day Suncor Extraction pumps more than 1,000,000 tonnes of aggressive slurry into and out of the two extraction plants.

May 1, 2003

By M. Cousineau, S. Gariepy

"Current business and corporate environments push for improving metal accounting practices in smelters. The ensuing projects commonly proceed along a bottom-up approach. As such, efforts are first put on reviewing the measurement system and then on remedying the identified weaknesses. The focus is thus moved to mass/metal balance only after the measurements upgrade process has been completed. However, practice has shown that assessing the high variances related to suboptimal measurement processes is complicated without the help of statistical data reconciliation. This bottom-up approach leads to a to-do list that can not only exceed available resources but also lack prioritization in view of achieving the targeted end use. This paper describes an upgrade project done differently where all the three dimensions of the metal accounting system: hardware, software, and people were instead involved at the onset. Personnel was thus trained on data reconciliation software at the beginning of the project to make the reconciled mass balance benefits available earlier in the upgrading project. This has pinpointed the most critical measurements where accuracy and reproducibility should be improved. Overall, not only the instrumentation retrofitting process has been streamlined, but the global risk for the whole upgrading project has been significantly lowered.INTRODUCTION Mining companies are pressured to improve their production accounting practices in response to the strengthening of corporate requirements for timely and accurate production reporting (Gaylard, Randolph, & Wortley, 2014). Smelters are not spared from these changes. However, their unique situation in the mining value chain set them as strategic targets for upgrading projects. They usually have a longer lifespan than concentrators thereby offering an extended lifecycle to justify investments. Furthermore, numerous smelters have toll agreements with third parties. Accurate cost and production accounting is, therefore, a vital piece of information to fix acceptable contract conditions. Mining companies are ultimately aiming at a clearer view of the operating performance of each business unit to improve their business decisions in a competitive environment. This sought for increase in visibility through plant performance can only be achieved through an upgrade of the metal accounting system. Figure 1 shows the different components of a state of the art system (Gaylard, Morrison, Randolph, Wortley, & Beck, 2009)."

Jan 1, 2017

By C. A. D' Odorico

The zinc pressure leaching (ZPL) plant at Teck Cominco's Trail Operations was started up in 1981 and represented the world's first commercialization of the technology. From the outset, the process was designed to operate using iron-rich Sullivan Mine zinc concentrate. When the Sullivan Mine reached the end of its life in 2002, the ZPL plant underwent a significant process change with the treatment of 100% Red Dog zinc concentrate. Through careful improvements to existing plant processes, controlled changes to plant operating parameters and a rapid adjustment to the modified process by operations personnel, the plant has been successfully converted to processing a feed of 100% Red Dog zinc concentrate. This paper discusses the challenges faced during the conversion and describes the modifications to plant operating procedures, as well as changes to plant processes.

Jan 1, 2004

By E. Hasanbas

Vibrating screens and crushers are the workhorses of material sizing. Unfortunately their natural frequency is often in the range of typical supporting structures, thereby making installations prone to vibration problems. Much of the available literature regarding the support of vibrating screens is fairly confusing and outdated. This paper presents the results of utilizing accelerometers and finite element software in the analysis and design of supports for vibrating equipment. It contains data from field studies of vibrating screen and crusher installations, design of new and repair of existing supporting structures, and the correlation between field data and finite element time history analyses. Finally, the paper summarizes a method for analyzing and designing structures subjected to vibratory loads and predicting their behavior.

Feb 23, 2014

By Santosh Kumar Ray, DEBASHISH MISHRA, Niroj Kumar Mohalik, SOMU MANDAL, Jai Krishna Pandey, Asfar Mobin Khan

Coal is a low-cost and high-calorific-value fuel. The coal mining industry worldwide has been suffering from severe accidents due to coal dust explosion hazards since its inception. Statistically, it was observed that 12,489 fatalities had occurred in 104 reported mining accidents from coal dust explosions during 1900–2020. There are numerous methods for detection, prevention, and control of coal dust explosions in mines. The underground mining environment is unpredictable and has an array of variables. These undulating factors make it difficult to prevent or control the coal dust explosion hazard. However, coal mining is done aggressively throughout the world, especially in developing countries as coal is a major source of thermal energy used in power plants contributing to about 38% (IEA, (2019), World Energy Outlook, IEA, Paris https:// www. iea. org/ repor ts/ world- energy- outlo ok- 2019.) of world electricity. Worldwide, coal dust explosibility studies are carried out in experimental mines, laboratories, and simulations. The complexity, lack of proper infrastructure, and unavailability of laboratory equipment sometimes make it difficult to study coal dust explosibility. The authors have discussed in detail and proposed that the CFD modelling can be a viable option for studying and evaluating coal dust explosibility.

Jun 29, 2022

By DEBASHISH MISHRA, SOMU MANDAL, ASFAR MOBIN KHAN, JAI KRISHNA PANDEY, NIROJ KUMAR MOHALIK, SANTOSH KUMAR RAY

Coal is a low-cost fuel with high calorific value. Statistically, the global coal mining industry suffered 12,489 fatalities in 104 reported mining accidents from coal dust explosions during 1900 to 2020. This review article discusses the occurrence, mechanism and explosibility parameters of coal dust explosions and presents a literature survey of the laboratory and computational fluid dynamics (CFD) simulation methods of studying them, as well as a comparison of the two methods.

Feb 1, 2023

By ERIK CHARRIER, ADITYA JUGANDA, Jürgen Brune, Gregory Bogin, Patrick Maier

Confined explosions are a major risk in underground coal mine operations. Depending on confinement, ignition location and obstacles in the flame path, methane explosions can transition to detonations. This research focuses on explosion experiments in a reactor with diameter of 71 cm and length of 30.5 m, along with developing the corresponding computational fluid dynamics (CFD) model that captures the observed flame behavior. The results show that the 2D and 3D CFD models are able predict the experimental flame front propagation velocity, but the 3D model shows more explicit conformity than the 2D model.

May 1, 2024

By ERIK CHARRIER, ADITYA JUGANDA, Jürgen Brune, Patrick Maier, Gregory E. Bogin Jr

Confined explosions are a major risk in underground coal mine operations. Depending on confinement, ignition location and obstacles in the flame path, methane explosions can transition to detonations. As a result, the severity of mine explosions ranges from minor damage to loss of lives and permanent mine closure. Experimental results have shown that the inclusion of obstacles can significantly increase the flame propagation velocity by inducing turbulence. This research focuses on explosion experiments in a 71 cm diameter, 30.5 m long reactor that includes rock piles as obstacles along with developing the corresponding CFD model that captures the observed flame behavior and interaction with the obstacles. The rock rubble increases the flame front propagation velocity by 500% compared to the maximum velocity observed in the empty reactor experiments. The 2D and 3D CFD models predict the experimental flame front propagation velocity, whereas the 3D model shows a more explicit conformity than the 2D model. Although the computational time to complete the simulation is much less for the 2D model than for the 3D model, the 2D model is not sufficient to simulate cases with rock rubble since it cannot capture the propagation of the flame through the small voids between the rocks with the same effective blockage ratio as the 3D model. The validated CFD model can be scaled up to simulate methane explosions in full scale mine and industrial settings.

Nov 20, 2023

By P. D. Barrette

This paper deals with the flow of granular materials in bins. A hybrid Lagrangian-Eulerian numerical model is introduced. The model is based on Particle-In-Cell (PIC) advection, and continuum equations describing a Mohr-Coulomb criterion. Experiments were conducted to test and verify the performance of the numerical model. Tests were done using three types of particles. Measurements of material properties and flow rates were carried out. Video records were also obtained and used to examine flow patterns. The results indicate that the numerical simulations produce deformation patterns and flow rates which are in good agreement with the experimental observations.

May 1, 2007

By Chinmay Shingote, Robert Visintainer, Renjie Ke, Jaikrishnan R. Kadambi, John Furlan

Hydrocyclone separators are some of the most widely used instruments in a variety of industrial applications. Their major functions are to sort, classify and separate solid particles and liquid droplets within a multiphase flow system. Research studies employing both experimental and numerical methods recognize that the performance of a cyclone is related to its geometric dimensions as well as the inner flow pattern. Although many successes have been achieved over the past years, the majority of investigations only focused on the simplified design of cyclone geometry and on single-phase flow. Therefore, this study set out to investigate the flow field in a new-design hydrocyclone and used particle image velocimetry (PIV) to explore the complex swirling flow behavior inside the cyclone within an air core. The flow field inside the cyclone was also studied by computational fluid dynamics (CFD) simulation using a commercial CFD package. Different turbulent models were tested in this study with a moderate-size mesh, and the interface of liquid phase and air phase was predicted by the volume of fluid (VOF) model.