Search Documents

By Rodolfo Zanella

Au/TiO2 catalysts prepared by deposition-precipitation with NaOH (DPN) (~3 wt%) and urea (DPU) (~8 wt%) were tested in crotonaldehyde hydrogenation at atmospheric pressure. There is no differences in activity (mole.gAu -1 s-1) and selectivity between both DPU and DPN samples for a given activation treatment. This is due to the fact that DPU and DPN samples exhibit similar gold particle size distribution, although the gold loading in DPU is much higher that in DPN. The DPU samples were reduced under H2 at different temperatures (120-500 °C) or under air at 300 °C with various flow rates, to vary the average particle size within a large range, 1.7 to 8.7 nm. The selectivity to crotyl alcohol (selective hydrogenation of the carbonyl bond) is high, 60-70 %, and almost constant as a function of the particle size. The selectivity to crotyl alcohol is also constant for conversions between 10 and 50%. These results suggest that the adsorption mode of crotonaldehyde is of ?3 or ?4-type. In contrast, the TOF depends on the gold particle size, it drastically increases when the gold particle size is ~2 nm. Our results are in agreement with former studies that suggest that the gold atoms involved in the hydrogenation process are those of low coordination.

Oct 1, 2003

By MOHAMMAD R. H. GORAKHKI, Christopher A. Bareither, MANUEL APARICIO, Joseph Scalia IV

The focus of this study was on the evaluation of hydrologic and environmental behavior observed in GeoWaste and waste rock test piles. GeoWaste is a mixture of fast-filtered tailings and waste rock prepared as a tailings-dominated mixture. The two test piles included potentially acid-generating (PAG) waste rock and were operated for 26 months to evaluate whether GeoWaste can suppresses sulfide oxidation and production of metal-rich acid mine drainage relative to PAG waste rock. The test piles were constructed in the shape of truncated 5-m-tall pyramids with 25-m base sides and flat 5-m × 5-m top surfaces. Water content, temperature, electrical conductivity, and oxygen concentration were monitored in four layers and at five locations within each layer in both test piles. In addition, 5-m × 5-m lysimeters were installed at the base of each pile to collect leachate. Approximately 2660 mm of water was added to the surfaces of the test piles via precipitation and irrigation (irrigation ≈ 1050 mm applied at an approximately constant rate for 70 days). The measured saturation, oxygen concentration, electrical conductivity, and temperature in the GeoWaste and waste rock piles suggest more sulfide oxidation occurred in the waste rock pile compared to the GeoWaste pile. Observations from the pile experiments suggest that co-managing mine waste in the form of GeoWaste reduced acid generation compared to waste rock alone due to the lower permeability and unsaturated state of the GeoWaste pile that reduced downward migration of moisture and inhibited drainage.

Mar 31, 2021

By D. Suarez

The work of engineers responsible for the design and performance of mine facilities is often challenged by economic and practical constraints in the field. Problems have developed in implementing design criteria dictated by persons or agencies not familiar with the dynamic nature of mine engineering. Regional and site-specific conditions frequently require changes to standard designs, or the use of a completely innovative approach, which is not provided for in the regulations. The implementation of engineering design, therefore, usually requires a hard-sell approach to management and regulatory agencies that allows for a happy-medium to all parties concerned. Flexibility on the part of the regulatory agencies is needed to solve operational and environmental problems with sound engineering. Typical hydrologic issues which will be discussed fall in the following general categories: ? Design criteria for sizing water control structures (i.e., culverts, diversion and sedimentation ponds, ditches, etc.) ? Implementation (construction and operation) difficulties ? Regulatory compliance ? Reclamation planning with hydrologic considerations ? Protection of groundwater resources

Jan 1, 1986

By D. L. Whiting

Dump leaching and ,in-situ solution mining have received considerable attention during the past few years due to their apparent economic viability and minimal environmental impact. Solution mining actually dates back to the 17th century when leaching of copper ore was first reported. However-, modern day leaching didn't begin on a wide scale until the mid-1900's. In-situ mining for copper, nickel, salts, and oil shale is currently looking more attractive as the technology advances. Presently, about 15 percent of the copper production in the United States is from leaching operations at approximately 14 active sites, the largest of which are the waste dumps near the Bingham Copper Mine, Utah. To establish a common background, the discussion is centered around state-of-the-art conditions. For dump leaching, complications inherent to the physical conditions and chemical reactions such as channeling, porosity and permeability, sorption, air flow, rock alteration and pH control are discussed. Emphasis is made on those conditions which render solution recovery rates and solution mineral concentrations unpredictable. By illustrating typical and actual field conditions, the generally accepted flow theories for both dump leaching and in-situ solution mining, including rubblization, are presented. For in-situ mining, hydrogeologic techniques such as geophysical well logging, aquifer testing and digital computer modeling are also discussed. The importance of artificial fracturing and well stimulating to solution injection and recovery is made with regard to project development. Finally, the subject of water pollution control techniques and the potential impact of the

Jan 1, 1977

Reliable predictions of the long-term water quality and water level fluctuations in a final void are vital if mine operators propose to decommission final voids in open cut mining operations. The catchments feeding final voids typically comprise a large proportion of coal placed or re-shaped spoil piles. Spoil piles from open cut coal mining operations have distinctive hydrological characteristics, which result in unique run-off behaviour. There is a need to understand the nature of spoil hydrology processes in order to predict the long-term hydrological behaviour and water quality responses of such systems. Preliminary estimates indicate that it may take 20 or more years for a void to flood. It is impractical for mine owners and operators to wait until long-term hydrological and water quality conditions have been established in a void, before reaching agreement with regulators about mine closure conditions. Reliable simulation of the long-term water quality and water level fluctuations in a void are therefore. The adoption of an agreed modelling approach and sharing of results from field data programs could result in the establishment of a database that could be used, with regulatory approval, for assigning parameter values, without the need for a specific data collection program for every individual void. Industry and regulators should agree on the model adopted for predicting post-closure behaviour of spoil/void systems. This will require reliable, robust methods for field data collection. This paper describes the field monitoring, data collection, model preparation and simulations undertaken over a three year period for Australian Coal Association Research Projects (ACARP) Project C7007. It presents the findings of that research, and provides comment on aspects of the project that were undertaken well and on aspects that could have been done better. Limited data is presented in this paper due to confidentiality arrangements with the relevant mine sites.

Jan 1, 2003

By M. E. Wadsworth, G. W. Warren

INTRODUCTION Hydrometallurgical processes for the extraction of metal values can be divided into two broad categories: (a) Processes involving the treatment of high grade material (e.g. finely divided mineral concentrates); and (b) processes which treat lower grade material (ores, waste dumps, etc.). This discussion will be directed primarily toward the first category, but in either case a fundamental knowledge of the intrinsic kinetics and thermodynamics is necessary to understand the behavior of the system. The bulk of research efforts in the last decade along these lines has been aimed at the recovery of copper (1-8). However much information has also been reported on uranium (9, 10) , zinc (11) , cobalt and nickel (12, 13). More comprehensive reviews on these areas are also available (14). As discussed by Sepulveda and Herbst (15, 16) one of the most difficult problems facing process designers is the acquisition and scale-up of reliable information concerning the intrinsic kinetics of leaching systems. The scale-up or modeling of these multiparticle systems is far more complex than that of homogeneous ones. This is due to the numerous rate determining steps which are possible with heterogeneous reactions and the broad distribution of properties of a multiparticle feed such as particle size and mineralogical composition (16). In addition, other factors must also be considered such as interactions between particles, the anisotropic nature of individual particles, the effect of solution chemistry, and electrochemical phenomena. All of these factors must be taken into account, often simultaneously. The thrust of this paper will be to more closely examine how the factors mentioned above can be treated. Some elementary examples of

Jan 1, 1980

By NEHA PANDEY, Sunil Kumar Tripathy, ARIJIT BISWAS

Due to the growing market of Electric Vehicles (EVs), there is a rise in battery demand. Nickel can be used as a potential element in cathode for lithium-ion batteries. Nickel can provide thermal stability, high energy density, and conductivity in cathodes of lithium-ion batteries. Low-grade chromite overburden from Sukinda mines contains less than 1 wt% of nickel, which can be utilized to extract nickel. Recovery of nickel from such low-grade overburden can help in value addition. The present study provides deeper insight into the aspects of extraction of nickel product derivatives (NPDs), mainly mixed hydroxide product (MHP), through the hydrometallurgical route. The current study focuses on extracting nickel and cobalt from a mine overburden with 0.41% nickel with major silicate gangue. MHP can be processed further for nickel sulfate production, a potential raw material for cathodes in EV batteries. The study discusses a process flowsheet to recover nickel and cobalt from overburden through atmospheric leaching with pre-calcination. It is observed that the step of pre-calcination improves the effective recovery of nickel from overburden. The leaching reactions are effective at a temperature of 90 °C and 1 atmosphere pressure. The orthophosphoric acid was used as a lixiviant for the selective recovery of nickel and cobalt from overburden. Recovery of nickel and cobalt obtained at optimum conditions is 84.0% and 39.9%, respectively. The iron impurity in the leachate solution is 1.27%. It is concluded that the process with pre-calcination along with acid leaching is effective for extracting nickel and cobalt at atmospheric pressure.

Dec 28, 2023

By D. Lunt

Telfer bulk concentrates typically contain 8% chalcopyrite, 8% chalcocite, 45% pyrite and 80-120 g/t gold. Although very high copper and gold recoveries can be obtained by subjecting the concentrate to a "conventional" high temperature pressure oxidation step followed by copper recovery by solvent extraction and electrowinning, and cyanidation of the leach residue for gold recovery, the cost of lime required for neutralisation and power for oxygen generation was such that the process was uneconomic in terms of operating costs. The challenge therefore was to develop an alternative flowsheet that maximised copper and gold recovery in which the reagent costs were commercially attractive. An additional objective was to reduce the capital cost so that the overall NPV and IRR values would enhance the economic viability of the total project. Following a series of batch and locked cycle testwork programs, supported by Metsim modelling, it was established that the same high levels of overall copper and gold recoveries can be obtained by use of a novel two-stage split leaching circuit in which the chalcocite component is leached in a low temperature (90-110°C) circuit with the chalcopyrite component treated in a high temperature (220-250°C) circuit. This split circuit has a number of advantages, including minimising the required capacity of the high temperature autoclave, as well as reducing the overall lime consumption and simplifying the total process water balance. The paper outlines the basis for the development of the flowsheet and discusses the integration of the leaching stages into the overall circuit.

Jan 1, 2004

By Dirk Verhulst, V. I. Lakshmanan

Why Chloride Hydrometallurgy?The most available, cheapest and best known reagent for treating ores and other raw materials for the metallurgical industry is sulfuric acid. Hydrochloric acid is second in line. What often happens is that a process is developed on the basis of sulfuric acid, and that at some point the question arises: wouldn't hydrochloric acid do this better?Considering hydrochloric acid immediately opens a very interesting field of research. To summarize a few comments from another paper presented at this symposium [1]: chlorides are far more soluble than sulfates (with a few interesting exceptions); the hydrogen ion activity is greater in chloride than in comparable sulfate solutions; higher oxidative conditions are possible; regeneration is more straightforward; more diversity is possible and better conditions for the separation of species can be found for solvent extraction and ion exchange; sulfur in the ore can be separated as elemental S; higher metal concentrations in solution and more flexibility in the chosen oxidation state means significantly lower energy costs.Also, the volatility of many chlorides at higher temperature allows further separation without the need to go to a different system. Chlorides also form molten salts with a low melting point, providing another means of separation and purification in the same chloride medium.

Jan 1, 2011

By Glaydson Simões dos Reisr

Micropore organosilicas (MOs) were synthesized using methyl-phenyl-polysiloxane as precursor. The MOs were characterized using several analytical and functional techniques. The materials were assigned as micropores materials, with specific surface area up to 642 m2 g-1 and yield up to 72.55%. The adsorbents have hydrophobic surfaces and were used for removal of diclofenac from aqueous solutions. The adsorption kinetic and isothermal data were well described by the general order and Sips models, respectively. Diclofenac exhibited a better affinity than NM and the mechanism of adsorption suggested that hydrophobic groups play a key role in the adsorption process.

Aug 17, 2017

By Elzbieta Mielczarski, Jerzy Mielczarski, Jan Drzymala, Yann Duvalm

Polyethylene glycol monoalkyl ethers (CnEm) render quartz hydrophobic while feldspar remains hydrophilic. As a result quartz can be separated from feldspar in small frothless flotation devices such as the Hallimond tube. The separation can be accomplished at room temperature at pH < 7 and C16E33 concentrations between 10-5 and 10-4 M for quartz particles smaller than 0.4 mm. No separation is observed when feldspar ore containing about 60 % of feldspar and 40% of quartz is subjected to flotation in a laboratory flotation machine. The reason for the lack of separation is a low hydrophobicity of quartz in the presence of polyethylene glycol monoalkyl ethers and high intensity of mixing in the flotation machine. The flotometric tests showed that the contact angle of quartz in monoalkyl ethers of polyethylene glycol solutions is less than about 18 degrees and depends on the structure and concentration of the ether and the pH of the system.

Jan 1, 2003

By R. Scheepers, J. E. Misiewicz, A. C. Fitzgerald

Discussion by A.C. Fitzgerald of the paper, published in Trans. IMM A, vol.104, 1995, p.B121-B135, is presented together with the authors' response. Fitzgerald points out a number of problems with the idea of mineralising fluids leaving no trace in the large volumes of rock traversed before depositing all minerals of value in a particular horizon or rock type with which the required isobaric or isothermic surface also coincides. He suggested that in the case of the Rooiberg tin deposits, the Lebowa Granites may be batholiths that reached the surface and were capped by sheets of their own volcanics. The authors agree that they had considered a possible syngenetic origin for the stratabound deposits, explain that no conclusive evidence for this could be found, discuss the relative ages of the sediments and volcanics of the Rooiberg Fragment and explain the role of its low-intensity deformation and flat dip in the coincidence of an isobaric-isothermic surface with the lithological stratification

Jun 18, 1905

By Masahiro Yoshimura, Sergiy Korablov

"Hydi-othermal corrosion ofTiN, TlAlN and CrN PVD films (3 µm thick) deposited on SUS-304 substrate was studied in 100MPa water in 20-950°C temperature range up , to 750h. The beginning temperature of their reaction was determined as 200°c for TiN and TiAlN and 500°C for CrN films, which are quite low in comparison with that of air oxidation of those powders. Very thin oxide scales. of TinO; n-I homologous series phases were formed above 300°C. TiO2 anatare. is observed for TIN and TiAlN films at 400°C. The· feature of hydrothermal corrosion of CrN films seems to be CrNxOy phase formation.Distinguishable weight changes were observed at higher temperature than 700°C for TiN, 750°C for· TiAlN and 800°C for CrN respectively. Hydrothermal corrosion kinetics .was constructed to calculate the activation energy of hydrothermal corrosions. On the base of obtained data, hydrothermal corrosion resistance was as follows: TiN – TiAlN - CrN. Facetted oxide crystals were formed at higher temperature than 500°C for TiN, TiAlN and 850°C forCrN.IntroductionThe metallic nitride (TiN; TiAlN, CrN) PVD films have high hardness, strength and wear resistance. Therefore these films are widely used in industry for wear resistij.nce application such as cutting tools and die molds. Their performances depend on not only the mechanical properties but also corrosion resistance of coated films. High temperature oxidation of metalliq nitride and nitride films was well studied [1-5]. However there are no reliable data concerning the .corrosion resistance of coated nitride materials. In high-temperature and high-pressure water. There are a few reports on hydrothermal corrosion of nitride films [6,7]. The increase of corrosion resistance of CVD films was observed in following succession TiC - TiCNO - TiCN - TiN at 300-680°C temperature interval and I 00 MPa pressure water according to data of the first report. Kawana et al. [7] have reported about excellent corrosion resistance of CrN films under 290°C and 8, 6 MPa water during I 000 h in the circulating type experimental loop. The films thickness was about 7-10 µm in both cases. However it remains unclear the chemical state of the surface species and especially in-depth distribution, oxide scale thickness and its growth, and defects formation in the oxide film."

Jan 1, 2000

By R. Quintero

The HYL Direct Reduction Process was the first in the world to operate successfully at industrial scale. The results were so innovative and attractive that other steelmaking companies acquired licenses for the HYL Process. Now in its 40th year of commercial operation, the HYL process has evolved into a modem, highly efficient and economical technology -HYL III. The technology offers high productivity, minimum energy and water consumption, electricity co-generation, raw material flexibility, premium quality DRI/HBI, and is highly versatile for meeting the specific needs of each user. A historical review as well as recent developments and future plans are presented in this paper.

Jan 1, 1998

By Steven Dapp

A new hyperbolic model for generating P-Y curves is developed for use in lateral analyses of cemented soils (a ?C-F? soil with both cohesive intercept and friction angle), and includes degradation of the static loading soil response to model the effects of load cycling (repeated loading) with load cycle number. The p-y curves, for both static and cyclic loading, were derived from full-scale lateral test results conducted on a set of six drilled shafts in a loess deposit at the Kansas DOT test site. Values of the model parameters obtained from the load testing at this site are presented, as well as a discussion of the model parameters effect on the results such that the model may be rationally applied to other sites with C-F type soils. A step-by-step procedure is presented to illustrate the application of the model. Correlation of the model to the CPT cone tip resistance (qc) from CPT testing is made, as this was found to be the most reliable; However, the model is applicable to other methods, both in-situ and laboratory, of assessing the soils strength.

Jan 1, 2011

By C. Ndou, T. Mothupi, H. Mandende

The technological advances in efficient, rapid, and non-destructive hyperspectral core logging systems for systematic mineral mapping have led to the discovery and exploitation of new mineral deposits Hyperspectral imaging in the long-wave infrared range has been recently used successfully to identify various phosphatebearing minerals (monazite, xenotime, and britholite), with limited work on apatite associated with mafic-ultramafic layered intrusions. In this study we investigate the effectiveness of a hyperspectral imaging (HSI) system with long-wave infrared (LWIR) bandwidthsto identify apatite in the Upper Zone of the Bushveld Complex. The accuracy of the HSI results was validated by mineralogical and geochemical data. The two apatite-enriched zones detected by HSI suggesting widespread development of apatite throughout the uppermost 600 m of the Upper Zone. The lower apatite-enriched zone is approximately 40 m thick, while the upper apatite-enriched zone is about 23 m thick, consistent with previous thickness determinations by traditional logging and analytical methods. Spectral mixing observed in the response of apatite is ascribed either to the common association of apatite and olivine in these rocks, or to differences between the spatial resolution of the hyperspectral image and the size of apatite grains. The VNIR-SWIR wavelength region did not show prominent spectral features of apatite. Nonetheless, HSI in the LWIR range is effective in mapping apatite and should therefore be considered as an exploration tool. This research advances our knowledge of the reflectance spectroscopy of REE-bearing minerals, which makes it easier to detect, identify, and quantify REE-bearing silicate minerals by HSI.

Feb 6, 2023

By S Prakash, M Danish, D Kumar

The green energy transition is speculated to cause an increase in the demand for raw materials while recycling rates are improving; discoveries are required to maintain supply. Geological remote sensing offers a cost-effective way of exploring mineral resources. While satellite and airborne imaging are routinely used for exploration targeting, a gap remains at the outcrop scale. Hyperspectral imaging (HSI) is advantageous for large-scale regional mapping, typically performed from satellite or airborne platforms. Accurately mapping geological lithologies remains challenging in inaccessible areas, such as rough terrain or mine sites. Proximal sensing techniques can boost geological activities’ reliability, safety, and efficiency in exploration or during mining activities. It also generates objective, reproducible results and valuable raw data that can be archived, further processed, and re-interpreted. Ground-based hyperspectral imaging of outcrops has steadily increased during the last decade due to sensor development and better processing routines. There is often a big technology gap related to mineral mapping, integration of images and spectra (reduction in manual identification of minerals and types) and hyperspectral data visualisation through remote sensing. TEXMiN Foundation, in collaboration with its industry partner Dassault Systemes Foundation, carried out the project, ‘Developing Hyperspectral Image Processing and Analysis, build a rich library of Hyperspectral images of a vast range of minerals from India which will help in increasing prediction accuracy of mineral deposit for mining exploration’.

Sep 1, 2024

By S. Serranti

A fast, reliable, and low cost characterization of ore minerals products, as they result from different processing actions, represents one of the most challenging targets in the mineral processing sector. Today different techniques are available according to different sampling strategies and analytical principles. In this paper, the possibilities offered by the adoption of hyperspectral imaging based sensing units working both at micro- and macro-scale are presented and discussed. According to the different phases and stages of ore minerals and products characterization, and starting from the analyses of the detected hyperspectral firms, it is thus possible to derive useful information about mineral flow stream properties and their physical-chemical attributes. This last aspect can be utilized to define innovative process mineralogy strategies and to implement on-line procedures at processing level. The present study discusses the effects related to the adoption of different hardware configurations, the utilization of different logics to perform the analysis and the selection of different algorithms according to the different characterization, inspection, and quality control actions to apply. Keywords: process mineralogy, hyperspectral imaging, NIR spectroscopy, surface mapping, textural analysis, quality control

Sep 1, 2012

By Ken Wangerud

The benefits of historic mining to this country have been many, but have come at a cost to the environment that has only begun to be understood over the past twenty years. While estimates vary, it is generally recognized that there are over 200,000 inactive and abandoned hardrock mines, with most of them located in the western U.S. Only a fraction of them are believed to be sources of metal releases with significant adverse environmental effects to the watersheds and receiving streams. State water-quality and natural resource management agencies have noted that hundreds of miles of streams are metal-impacted, and the aggregate effects of these sites within watersheds and drainage basins is poorly understood. Resources for the environmental assessment of abandoned mine land (AML) sites and watersheds have been and continue to be limited. Few hardrock mining states receive substantial reclamation funds under the (coal) Surface Mining Control and Reclamation Act. EPA Region VIII (EPA8) has an estimated 90,000 abandoned mining, milling and smelter sites, mainly in Colorado, Montana, South Dakota, Utah and Wyoming. An estimated 13,000 of the sites may have metal releases causing Clean Water Act and CERCLA non-compliance. Results of inventories by states and federal land managing agencies, indicate it is plausible that only 3,000-4,000 of these sites may be causing significant environmental degradation.

Jan 1, 1999

By J Vann

The philosophical context of many activities in mine geology can be an important lever in adding value to operations. For mine geologists (including resource and grade control geologists) we argue that the tasks of problem formulation, observation and data collection, interpretation and modelling invoke various philosophical considerations whether the practitioner is aware of them or not.Constructing testable models to explain reality is the definitive aspect of any activity claiming to be ‘scientific’. A primary goal of mining geology is to build models that accurately predict reality to an acceptable degree and these include litho-structural, stratigraphic, grade control, resource or reconciliation models. What’s more, in mine geology we are often able collect additional drill samples or access new underground openings, for example, that can provide relatively rapid feedback on how predictive, and therefore useful, our models are. In this paper, we describe the key philosophical frameworks proposed for conducting scientific investigations, including falsification, the method of multiple working hypotheses and structural concepts of scientific theory. The strengths and weaknesses of these approaches are discussed and an attempt is made to relate them to activities undertaken by mine geologists. Common perceptions of what constitutes the scientific method have been dominated by how scientists do experimental physics and chemistry in particular. There are very important differences in the types of problem confronted in these experimental sciences compared to the ‘historical sciences’, such as geology, where the processes studied are unique and only evidential traces of past events are available. The philosophical implications of attempting to validate numerical geological models, such as resource estimates are also briefly considered.Some practical conclusions are drawn about how mine geology activities can be better implemented if practitioners are cognisant of the importance of philosophical considerations when attempting to gain new knowledge through a scientific investigation. We believe that the implications for creating additional value to a project or operation can be very significant when geology is applied by a practitioner with an understanding of the philosophical basis of the activities we think of as constituting a scientific investigation.Remember that all models are wrong; the practical question is how wrong do they have to be to not be useful? (Box and Draper, 1987, 74 p).The demand that theories be highly falsifiable has the attractive consequence that theories should be clearly stated and precise. If a theory is so vaguely stated that it is not exactly clear what it is claiming, then when tested by observation or experiment it can always be interpreted so as to be consistent with the results of the test. (Chalmers, 1999, 67 p).

Aug 22, 2011