Search Documents

Within the research project "Mine Development" funded by the "Austrian Fonds zur Forderung der wissenschaftlichen Forschung (FWF) " (funds for scientific research) between 1991 and 1993 150 underground hardrock mines in Europe, Northern America, Australia and Japan have been visited to analyze their general design and layout. The main aim of the project was to develop strategies for accessing new underground hardrock mines and to establish a mine planning database. The investigation included mines in high developed countries only, with a comparable labor cost situation. This paper presents the results of one part of the project, which deals with investigations into the influence of different parameters on the design of the primary access for a mine.

Jan 1, 1995

By Ralph H. Cleland

GENERALLY speaking, the Industry lost ground in 1941 in its accident experience. Though the frequency of compensation accidents was but slightly higher than in the previous year and well below past experience, our fatality rate shot up to that obtaining in 1938, and the average cost per man employed was the highest for some time. The number of fatalities was 56 in 1941 as against 33 in 1940. The average cost of compensation per man employed was $34.25 in 1941 as against $28.43. There was but a slight increase in the number of men employed. Accident prevention efforts were maintained, as shown by our frequency, but our accidents were of a more serious nature. In a period of considerable labour turnover, with many new men entering the Industry, especially the base-metal division, and much mental distraction, we might well have expected a high rate of accidents. That this did not occur is a tribute to managers, supervisors, and workmen alike. We all regret the high fatality rate and one must consider why this occurred. So far as it is possible to determine, there is no apparent explanation. There were no disasters. The accidents occurred to the same class of work-men, both in respect to jobs and age groups, and from the same age-old causes that we all know so well. Luck is a big factor in the seriousness of an accident; the solution lies in preventing accidents, even first-aid cases. Generally speaking, if minor accidents do not occur, major accidents do not occur.

Jan 1, 1942

The first metal-mine accident-prevention course was prepared and published in 1942-45 as a series of seven miners' circulars (Nos. 51-57). The scope of the course has been broadened, revised, and brought up to date, and it is being published as a similar series of seven miners' circulars on accident prevention in metal and nonmetallic mines. These circulars are: 1. Accident Statistics (Miners' Circular 51), dealing with general statistics on accidents and injuries at metal and nonmetallic mines, including causes, costs, and the uses of investigations and reports of all accidents.

Jan 1, 1957

The first metal-mine accident-prevention course was prepared and published in 1942-45 as a series of seven miners' circulars (Nos. 51-57). The scope of the course has been broadened, revised, and brought up to date and is being published as a similar series of seven miners' circulars (Nos. 51-57, revised) on accident prevention in metal and nonmetallic mines. These circulars are: Accident Statistics (Miners' Circular 51), dealing with general statistics on accidents and injuries at metal and nonmetallic mines, including causes, costs, and the use of investigations and reports of all accidents.

Jan 1, 1957

The original manuscript of section 2 of this series of miners' circulars devoted to accident prevention in bituminous-coal mines was completed in September 1944. At that time roof bolting had been tried with some success in the lead-mining district of south-eastern Missouri, but information on the subject was so fragmentary that it was not included as a method of roof support. References to roof support in bituminous-coal mines, therefore, were confined almost entirely to conventional timbering methods. In 1947 the Bureau instituted a research program and intensive study of the general problem of roof control, which emphasized roof-bolt application. The rapid increase in mechanized mining following the close of World War II provided the impetus for the Bureau's roof-control investigations, because the vertical supports used with conventional timber restricted the maneuverability of mechanical face equipment, and the industry wanted to explore every possible method of eliminating interference with the production cycle to gain full advantage of mechanized mining. Moreover, the accidental dislodgment of vertical supports greatly increased the roof-fall hazard. As roof falls have killed and seriously injured more mine workmen every year than any other cause or classification of injury since records have been kept, the Bureau assumed this investigative leadership with the prime objective of substantially reducing the annual toll from falls of roof, including falls of rib and face.

Jan 1, 1958

The first metal-mine accident-prevention course was prepared and published in 1942-45 as a series of seven miners' circulars (Nos. 51-57). The scope of the course has been broadened, revised, and brought up to date, and it is being published as a similar series of seven miners' circulars (Nos. 51-57, revised) on accident prevention in metal and nonmetallic mines. These circulars are: Accident Statistics (Miners' Circular 51), dealing with general statistics on accidents and injuries at metal and nonmetallic mines, including causes, costs, and the uses of investigations and reports of all accidents.

Jan 1, 1955

By G R. Hancock, S Grant, T Whiteside, J B. C Lowry, J Boyden, T J. Coulthard

Physically-based landform evolution models (LEM) provide a spatial framework to forecast the long-term geomorphic stability of post-mining landscapes. When used to test the relative stability of different landform designs, LEMs may assist with the development of optimal closure designs for rehabilitated mines. However, in order to reduce prediction error, factors controlling landscape evolution must also be accurately represented by models. This requires that the correct sets of processes are represented and that driving parameters used in LEMs are, if necessary, calibrated to the landscape of interest.Vegetation exerts strong controls on the hydrologic and geomorphic processes that drive landscape evolution. Hence, the spatial and temporal scales over which typical patterns in vegetation are represented in different landscapes are important considerations in LEM calibration. However, vegetation is rarely accounted for in LEMs and even when integrated is often represented simply, without representing spatial dynamics of vegetation cover that may impact landform development.This study focuses on characterising vegetation patterns to calibrate a new vegetation module of the The Cellular Automaton Evolutionary Slope and River (CAESAR)-Lisflood LEM to be applied to a conceptual rehabilitated landform of the Ranger uranium mine located in the Alligator Rivers Region (ARR) of northern Australia. In the ARR the spatial dynamics of vegetation over time are largely driven by monsoonal rains and topography. Extensive dry season fires are also common in the region, temporarily reducing vegetation cover where they occur. Hence, hydrology, topography and fire disturbance interact to shape a distinct, yet dynamic, mosaic of different vegetation types of varying cover density. As a basis for calibrating the new vegetation function, the distribution and dynamics of vegetation are characterised for this savannah landscape by remote sensing, in conjunction with ground data.CITATION:Boyden, J, Lowry, J, Coulthard, T, Whiteside, T, Hancock, G and Grant, S, 2016. Accounting for vegetation dynamics in landform evolution modelling, in Proceedings Life-of-Mine 2016 Conference , pp 63–66 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By D. T. Pritchard

"Introduction""No accounting system is very good, and all of them are infinitely variable*.”The purpose of this chapter is to discuss those facets of a typical accounting system which are most commonly encountered by operating managers in mineral processing plants. However, before concentrating in any detail on these it is important to understand the broad purposes and basic techniques of any accounting system in any major business.The three broad purposes of an Accounting System are:- Administering, controlling, and recording the flow of cash in and out of the business. Cash is, of course, converted into other assets (or stores of value) such as inventory, plant and equipment, etc. These assets also have to be administered, controlled and recorded.- Internal reporting to Management for information, for control, and for use in making business plans and decisions. - External reporting to stockholders, government, lenders and other outside parties.In this chapter we shall organize our discussion of accounting practice in mineral processing plants around these three purposes of accounting and focus in some detail on specific practices and techniques with which operating personnel will be routinely involved. This chapter is divided into the following: Accounting Basics; Administration, Control and Recording of Cash Flows; Internal Reporting; Planning and Budgeting; Cost Control; and External Reporting."

Jan 1, 1989

By E. Westman

Geographic Information Systems (GIS) are becoming a more commonly used tool for resource estimation as they provide not only a database management platform, but also the graphical capabilities to visualize resource characteristics. Interpolation methods used commonly in these resource studies do not typically provide a quantitative answer to the question: "How accurate is the estimate?" By comparing localized measurements at several locations to the interpolated thickness distribution used in a resource estimate, a quantitative analysis of accuracy can be obtained. The technique is demonstrated with a case study from Central Appalachia.

Jan 1, 1999

A nuclear technique utilising the gamma-ray resonance scattering process is used at Isa Mine for the determination of copper in drill core and bulk mineral samples. The Copper Bulk Analyser (CBA) provides quick and accurate non-destructive copper analysis of drill core at costs two to three times cheaper than conventional chemical techniques.The almost immediate availability of sample results enhances the efficiency of the mine geologist in the duties of grade control, design of diamond drilling programmes, and input to planning. The unit has proven to be a reliable and accurate production tool requiring a minimum of technical support.

Jan 1, 1990

By Richard L. Bullock

Believe it or not, mine evaluation and feasibility studies are as old as the industry itself. In the first recorded writing on mining by Agricola (1556), he gave several clues as what to look for in evaluating a mine, to determine if it was economically feasible. Below is the guidance from Agricola, with my interpretation of what he would include today. Now a miner, before he begins to mine the orebodies must consider seven things, namely: ? The situation (the geography/topography). ? The conditions (the geologic/mineralogic and mining conditions). ? The water (availability, hydrology and ownership). ? The roads (plus the railroads, power lines, all other infrastructure). ? The climate (the weather-rainfall/environment). ? The right of ownership (the land and legal entitlement). ? The neighbors (the social environmental concerns of the area). It is amazing how much of his guidance has not changed in 455 years. Yet Agricola gives no guidance on determining the correct cost, or determining the correct commodity pricing. But he does give a few words of caution on the related ethics involved on buying mineral properties: ?A prudent owner, before he buys shares, ought to go to the mine and carefully examine the nature of the vein, for it is very important that he should be on his guard lest fraudulent sellers of shares should deceive him.? Three hundred years later (1866), to further amplify this point, in the most famous thing that Mark Twain never said, as an introduction to a lecturer to an audience of gold-miners at Red Dog, CA, the famed author/humorist allegedly described a mine as ?a hole in the ground owned by a liar? (Farrar & Rinehart, 1935). So, one might conclude that between these two dates, the mining industry did little to improve its reputation. Unfortunately, since Mark Twain allegedly made those remarks, we have not done near enough to gain accountability for the mineral industry.

Jan 1, 2011

By Mahesh Hingorani

Integrity issues for bored cast-in-situ piles have raised the need for the use of non-destructive tests to verify pile integrity and detect possible anomalies in installed pile sections that could adversely affect their serviceability. Integrity inspections performed after installations are often the most reasonable alternative available to assess the shaft quality. The two most common methods are pulse-echo from a small hand held hammer at the pile top, and cross-hole ultrasonic transmissions along the shaft between parallel sonic pipes. While different in technique, each method has its advantages and limitations. This paper emphasizes more on the degree of accuracy of low-strain pile integrity test by comparing the results with cross-hole sonic logging. Reliable data collection and interpretation by an experienced test engineer will reveal the integrity of the pile. Cross-hole sonic logging and low-strain pile integrity testing were both specified as quality control measures for a metro rail project in India. Both cross-hole sonic logging and low-strain pile integrity testing indicated defects in several bored piles. Also minor imperfections recorded by cross-hole sonic logging were observed in low-strain results. The observations of the two test methods are presented and compared for a better understanding of the importance of low-strain test results for any project. INTRODUCTION Cast-in-situ concrete piles are often chosen as a deep foundation alternative where challenging soil conditions exist. Although quality control measures are almost always taken during the installation of the piles, it is often difficult or impossible to confirm the integrity of the pile at this stage, particularly in wet conditions. Because of the relatively high probability of bored piles having anomalies, quality assurance of each bored pile is essential for each project.

Jan 1, 2019

By Williams DJ, Battino S

The rapid crushing technique for the measurement of gas content of coal consists of accelerating the rate of gas desorption from coal by crushing. This technique allows the determination of gas content in the space of hours rather than days or weeks as required for the traditional slow desorption technique. The crushing technique is used particularly when gas content determinations are urgently required for mine safety purposes. The method is now routinely used in underground coal mines of NSW and to a lesser extent in QLD. Despite the rapidity and efficiency of this method, concerns have been raised upon the reliability of the method to deliver accurate results. Experience in Australia has shown that there is in fact some discrepancy in results between gas laboratories using the rapid crush technique. The development of rapid crushing techniques for seam gas content measurements in Australia and the main causes of variability in the gas content test results were investigated. The gas laboratories participating in the gas content testing were CSIRO Division of Coal and Energy, BHP Technical Services and GeoGas Pty. Ltd.

Jan 1, 1998

By Brad McBain

Agenda ? Accurassay Laboratories and Automation ? History and experience ? Features and benefits of automation in the lab ? Tata Steel Minerals Canada (TSMC) Iron Ore Laboratory ? State-of-the art systems and design ? The integration of fusion systems and XRF units ? Meeting deliverables: quality, reliability, safety

Aug 1, 2013

By M. Dupuis

In the present study, the heat balance of the Hirakud smelter aluminium reduction cell has been accurately assessed using only a surface thermocouple and a pyrometer, As it is well known that using a single linear or quadratic relationship to estimate the heat flux from the measured surface temperature does not provide the accuracy required to close the cell heat balance, this approach was not used in this study, Instead, the fundamental natural convection and radiation heat flux equations were used systematically for each measurement point, Practically, this means that the ambient air temperature and at least one ambient radiative temperature must also be known in addition to the surface temperature for each measurement point. Sometimes, the radiative heat flux could not be accurately estimated using a single ambient radiative temperature, In those cases, a more accurate estimation based on two ambient radiative temperatures and corresponding view factors has been used instead, It turns out that although at least three temperature measurements are required to estimate a single heat flux, it takes a lot less time to make those temperature measurements using a pyrometer than directly measuring the heat flux using an expensive heat flux meter, Furthermore, no loss in accuracy was detected when using this approach as the cell heat balance could be closed within 5%, the level of accuracy typical of cell heat balance assessment using heat flux meter.

Jan 1, 2004

By G. Bonin, A. Jamal, G. Preciado, S. Gillis

"Accurate, easy to obtain, and reliable methods of measurement are the cornerstone of shaft and tunnel developments - during their sinking, operation and maintenance, or in some cases, remediation. This paper presents a new methodology to capture existing shaft conditions in such a manner that they can be transferred from the field to a digital copy, where they can be stored and used for engineering design purposes in a space not directly affected by the costs associated with schedule and equipment performance. The methodology utilizes basic principles of excavation alignment (plumb lines and survey instruments) while adding modern LiDAR, geolocation and survey control tools that can more completely capture the surrounding environment. The complete cycle of collection, processing, and delivery of pertinent information underground can take under an hour. During sinking, capturing data as a live stream measurement and being able to assess the alignment of the shaft liner can be critical to meeting rigid design tolerances. As sinking progresses, small changes in alignment or liner deviations can be captured and immediately corrected. Likewise, post-construction as-built conditions can be recorded and digitized, which will allow the mine personnel to compare the proper working condition to the actual condition years later. Observed changes can be identified and planned as future shaft repair works. This methodology has been developed and successfully deployed during the on-going sinking works of the two shafts at the Jansen Potash Project in south-central Saskatchewan and is described in greater detail in this paper.INTRODUCTION Light Detection and Ranging (or LiDAR) scans of the BHP Jansen Production and Service shafts during construction identified sections of both shafts where the internal radius of the temporary primary liner was insufficient to accommodate the tolerances of the permanent liner that was to be installed inside the temporary liner. These locations are referred to as “tights”. The “Tights Removal Program” was designed to collect high resolution point clouds of the shaft, using stringent survey control, that could be compared to the design profile to generate a heat map of locations for removal of up to 75 mm of steel-fiber-reinforced, 70 MPa concrete liner. This work was all on critical path, which made it valuable to save time on the schedule. Because concrete removal was a time-intensive task, it was essential to locate and remove only the concrete that would encroach on the planned permanent liner, while attempting to maximize the amount of cutting time. Removal was carried by a road header attached to a Brokk(R) 160, a small multi-attachment demolition machine."

Jan 1, 2019

By Jim Hardy, Tim McKnight

"The thermal mass flow controller, or MFC, has become an instrument of choice for the monitoring and controlling of process gas flow throughout the materials processing industry. In the semiconductor industry, these MFCs are used on over 70% of the processing tools. Reliability and accuracy are major concerns for the users of the MFCs. Calibration and characterization technologies for the development and implementation of mass flow devices are described. Sources of inaccuracy in process gas handling are described, and a model to correct for these inaccuracies is outlined. A gravimetric calibrator is described that allows flow sensors to be calibrated in corrosive, reactive gases to an accuracy of 0.3% of reading, at least an order of magnitude better than previously possible. All described capabilities are implemented in a Department of Energy User Facility which is available to industry and universities to test and develop gas flow sensors and controllers and evaluate their performance related to environmental effects, reliability, reproducibility, and accuracy.IntroductionMaterials processing is at the heart of semiconductor manufacturing. To make today's advanced integrated circuits, silicon wafers are subjected to over 200 process steps. Most of these steps involve processes such as etching, implanting, diffusion, annealing, deposition, and lithography (resist deposition and hardening). Often one or more process gases are used to complete the process step. To achieve the quality and performance required in the micro devices, accurate measurement and control of these gases is essential. The Oak Ridge National Laboratory (ORNL), in conjunction with the semiconductor industry, has been working to improve process gas measurement and control accuracy and reliability. Standardized test methods have been developed to characterize and benchmark the performance of mass flow controllers (MFCs), the method of choice for monitoring and controlling gas delivery. Testbeds have been designed and fabricated to produce repeatable and accurate data using these standards. Baseline testing was performed along with development of a unique mass flow instrument, the gravimetric calibrator."

Jan 1, 1997

By Derrick Hunter, Pat Feighan, Keith Chrystall, David Wells

"Equipment which may be remotely operated, has some degree of on-board intelligence, and which for periods of time may operate autonomously, is referred to as telerobotic. Recent advances in electronics, computers and hydraulic equipment have dramatically reduced the cost and simplified the process of converting standard industrial equipment to telerobotic control. The benefits of telerobotic equipment include improved safety by removing the operator from dangerous situations, reduced maintenance costs and increased productivity. This technology has been proven in various military, nuclear, and police applications.The surface mining industry has expressed an interest in automation and is characterized by a willingness to use remotely operated equipment, however, the majority of telerobotic equipment currently in use is experimental or prototypical. Potential applications of telerobotic equipment for surface mining include remote operation of equipment near dangerous high walls and other unsafe areas, utilization of robotic trucks for routine hauling operations, and control of jointed equipment. In addition, component technologies of telerobotic systems are relevant to various forms of condition monitoring, operator feedback systems, and vehicle positioning.Attention must now be directed toward resolving more complex problems associated with enhancing feedback to the operator, improving the man/machine interface, and ultimately, improving efficiency. Removal of the human operator from the work site introduces significant complications in replacing the sensory inputs that an operator normally uses to efficiently run his machinery. These can be difficult to define and even more difficult to replicate remotely and may include restrictions pertaining to vision, hearing, and touch.In cooperation with Defence Research Establishment Suffield and the Alberta Research Council, Robotech Industries Ltd. is pursuing the development of additional technologies to further enhance an operator’s ability to control remote telerobotic equipment. These developments include a head-mounted display, additional control station displays and improvements to coordinated motion control software. Prototypes of these developments are expected to be completed and tested by the fourth quarter of 1997."

Jan 1, 1996

By Gerardo Vargas

Without an adequate data sample there can be no Reliability Analysis (RA). Without analysis there can be no systematic, verifiable improvement in reliability or in operational economy. A sample is a collection of life cycles. A beginning and ending event define a failure mode life cycle. Well known obstacles impede the reliability engineer in his role to analyze maintenance data. The main problem lies in the difficulty to obtain analyzable data samples. Although modern Computerized Maintenance Management Systems (CMMSs) should provide the needed information they rarely deliver samples of adequate quality. Cerrejon, an integrated mining operation in Colombia, South America solved the information management problem by applying a "Living Reliability Centered Maintenance (LRCM)" process to its fleets of Trucks, Graders, Dozers, Loaders, and Shovels. This paper describes a method wherein completed work orders capture reliability analysis enabling information. The 'right' maintenance observations reference significant failure modes. Work orders link to records in a continuously growing Reliability Centered Maintenance (RCM) structured knowledge base. Grouped and filtered knowledge-to-work order links, being instances of failure modes, provide the samples required by reliability analysis software tools and methods. LRCM software and related procedures facilitate the growth of knowledge, manage the work order-to-RCM relationship, and generate samples for subsequent reliability analysis.

May 1, 2011

By T. D. Chatwin

While new jobs and taxes are major incentives for support of mining, stakeholders must also be assured that current jobs, resources and environment will be protected. Mining companies can help achieve stakeholder support by frankly addressing Acid Rock Drainage CARD) issues. To prevent ARD, miners must begin early in the mine life-cycle to develop an ARD management plan and integrate it into the mining operation. As this proactive preventative program is initiated, mining companies also need to engage and collaborate with stakeholders to insure that their expectations and needs are met. Stakeholder engagement is enhanced as mining companies emphasizes the value of clean and available water for current and future generations.

Jan 1, 2011