Search Documents

By S. E. Knalafalla

The availability of a fluid whose gross behavior sharply changes in a magnetic field without affecting its rheologic characteristics has been recently demonstrated. A colloidal solution of a ferrimagnetic material, such as magnetite, in a liquid that is immiscible with and lighter than water is projected for use in selective separation of particles according to their density spectrum in a continuous fashion. Magnetic levitation forces were created as an antigravity field when the fluid was properly placed in an inhomogeneous magnetic field. Five spherical non¬magnetic objects with densities ranging from 2.70 to 11.35 gram cm ' were made to float or submerge at will in a 0.96-gram cm-3 density fluid placed at vertical magnetic field gradients ranging from 0.2 to I kilooersted cm-1. The magnetic levitation farce in dyne cm-3 was found to vary linearly as a function of the object-fluid density mismatch with a slope equal to one g, the acceleration due to gravity.

Jan 1, 1972

By C. A. Heiland

THE investigations described were made on a portion of Clear Creek basin near Golden, Colo. (A portion of the area under survey is shown in Fig. 1. The photograph was taken in the vicinity of station No. 2 of Line II.) Three principal purposes were in the minds of the investigators: 1. To repeat with modern, more sensitive and more reliable instruments magnetometric placer investigations previously made. 2. To disprove the recently advanced theory that deposits of the glacial period have no pronounced magnetic effects. 3. To develop in detail the theory of the magnetic effects produced by placer deposits. Six years ago, the first magnetic observations were published, which proved that it is possible to locate gold-bearing channels with relatively crude instruments.1 Two years ago, K. C. Laylander published results obtained with similar instruments.2 The measurements of the latter were discussed by the senior author of this paper.3 At that time, however, the material available for such a discussion was somewhat scarce and not made with the most modern magnetic instruments, although very brilliant results were obtained. Therefore, the senior author felt that magnetic investigations should be made on very clear geologic conditions with the most modern instruments.

Jan 1, 1928

By D. Rudenko, C. T. Aimone-Martin, J. K. Ratliff, I. G. Wong, J. Aiken, R. E. Burnham, T. A. Davidsavor

A small quarry blast was conducted with a maximum of 90 pounds per delay and shortly afterwards, area residents sensed ground motion and building shaking indicative of an earthquake. In addition, seismometers up to 500 miles (800 km) away recorded a magnitude 2.8 earthquake located in the area. Positioned in a seismically inactive area, southern Minnesota is not known for earthquakes. The earthquake was originally described by the USGS to be a surface blast at the quarry. Analysis showed that the earthquake occurred shortly (approximately seven seconds) after the quarry blast some distance away and well below the surface. This paper describes the evaluation of the “seismic events” including the blast, the following earthquake, initial governmental response, and provides the framework for assessing the relationship between the blast and the earthquake. The paper also discusses management of large volume claims from a complex event and presents a claims management strategy with best practices.

Feb 6, 2023

By J. A. Domenico

A safe and precise mineral separation alternative to heavy liquids is being used for mineral sands exploration on large scale orebodies. The separation process, Magstream®, uses ferro-fluids and magnetic and centrifugal forces to produce precise split points over a range of specific gravities from 1.5 to 18.0 g/cc. This paper describes a commercial scale exploration program treating, roughly, 90 samples per day in Senegal (West Africa). Separation results comparing Magstream® and conventional heavy-liquid separation are presented.

Jan 1, 1994

By David Beck

In Australia, Safe Work legislation requires mines to have a documented ‘Safety Case’ explaining how a mine will safely manage all major hazards. A similar requirement is legislated or inferred by regulation in all jurisdictions. For small scale, instabilities leading to day-to-day seismic hazards, a ‘Stability Safety Case’ built around observational methods and measurement triggered responses can be effective because adverse situations are easily identified and the costs of lower control measures are not onerous. Also, if the influence of a volume of yield on the mine load system is small, the response of the system will be more predictable. However, for episodes of large scale mine instability, the hazard derives from the widespread, multi component influence of the event on the mine load system. As the system response depends on interactions between many parts, the resolution of predictions will be lower and situations can arise without local precedent. Further, as episodes of large scale instability change the stiffness and nature of the connectedness between parts of the mine load system, the behavior of the system before the event will be a poor empirical basis for forecasts of event related hazards. Most importantly, Triggered Action Response Plans (TARPs) and ‘traffic light’ warning systems cannot make design choices or identify new hazard phenomena. They are ‘lower’ control measures targeting explicit human-made instability hypotheses. As such, the Safety Cases related to management of hazard from potential large scale seismic events and mine instability cannot rely solely on TARPs. Mines that successfully manage meaningful dynamic instability always acknowledge the ultimate reliance on expert human intuition, knowledge and imagination to appreciate the range of possible hazard scenarios, to make stability hypotheses and propose solutions. Complex analysis, TARPs and measurements are critical steps in the human decision cycle, but only support the making and testing of ‘Stability Hypotheses’ made by expert engineers. Relying on expert skill and judgement as essential components of a Safety Case, however essential, introduces human vulnerabilities. Another challenge is that the expert decision making process is hard to document. Beck et al 2019 first described an organizational and procedural framework for maintenance of an ongoing large-scale ‘Stability Safety Case' where a degree of expert judgement and imagination is needed to manage a seismically active mine. The structured data appreciation process outlined sufficient measurements, analysis and appreciation to confirm the stability state of the mine and was applicable to all underground mines. After several years of implementation in various forms in stoping, caving and room and pillar mines, this update addresses lessons learned and describes some considerations for numerical forecasting to establish a base case, and some challenges for empirical hazard identification.

Apr 26, 2022

Maintaining and improving the economics of open pit mining in the future requires understanding of the characteristics of open pit mining that are different to other mining or business activities, designing mines in the first place to be less susceptible to changes in these important characteristics, and adopting strategies which yield reliable returns despite unforeseen change. Planning and production personnel require guidelines and performance standards that are based on sound economics not solely on production criteria. The guidelines adopted for long-term implementation must assume a declining price for mineral products along with declining real costs, with research efforts directed at development of both evolutionary and revolutionary ideas aimed at implementation. Decision-making must focus on risk and probability criteria rather than just simple return-on-investment criteria, and the approach for management of personnel must support the higher level of communication essential for fast decision-making in the new environment of continual change.

Jan 1, 1992

By David Kress

Mill crushing drive systems are essential to cement producers. With the increased emphasis on operating efficiency, it is vital that these systems be dependable and reliable. No one needs the costs or headaches associated with unscheduled downtime or inefficient machinery operation. A reliable drive system starts with the proper selection of the ring, or girth, gear and continues through proper maintenance. Ideally, selecting the right girth gear brings together the gear manufacturer, the system designer and the end user. The gear manufacturer must know the details of the application, the demands that will be placed on the gear and the nature of the equipment to be driven. Similarly, the user and the system designer must be familiar with the variables that affect gear drive performance and service. For example, an application that places a torque load on the drive in excess of its rated capacity will result in gear tooth distress and, in severe cases, breakage.

Jan 1, 2000

Successful evaluation and exploitation of resources and reserves relies on the collection of high quality sample data. The quality of the sample data must be maintained through the application of a robust quality assurance and quality control (QAQC) program, including documentation of sampling procedures, training of sampling personnel and the regular monitoring of control samples. However, the application of QAQC programs in the minerals industry is often poor and the purpose misunderstood. It is all too common to have good quality control data collected, but no analysis work carried out until after drilling is completed. In a lengthy drill program, this can lead to problems not being discovered and corrected as they happen. Moreover, rectifying problems afterwards will be costly in terms of time and money, if not impossible. The consequences of poor quality sample data are many and include such effects as over- or underestimation of block grades, misclassification of ore and waste, and lower confidence in the resource/reserve models. The purpose of this paper is to highlight, using case studies, the importance of good QAQC practices to monitor the quality of sampling and laboratory sample preparation and analysis.

Mar 1, 2010

By A. P. Williams

"This paper presents an overview of plant electrical systems in general, a discussion of the problems that may occur due to plant growth, the maintenance required to maintain the reliability and safety of the electrical system, and the selectivity of the relay protection system. It is divided into two main areas: short circuit levels within the plant electrical system; and relay protection systems.This information is directed at maintenance supervisors, mine managers and electrical superintendents who have been away from detailed short circuit and relay coordination calculations for some time. It points out the potential problem areas within an operating plant electrical system. Short Circuit LevelsTheoryThe electrical equipment in a plant such as breakers, switches and starters has two short circuit ratings, the momentary rating and the interrupting rating. These ratings may be given in MVA or current (amperes) depending on the equipment and manufacturer's preference. Since for a three-phase system MVA and amperes are related by the formula"

Jan 1, 1987

The successful operation of diesel equipment underground does not entirely depend on selection of robust, reliable, easily maintained machines. Results are also heavily influenced by the following factors: Design and condition of the operating area. Skill of operators. Correct maintenance facilities. Experience, skill and initiative of maintenance personnel. If the mine layout does not allow access to a central workshop area, the effect of any shortcomings will be magnified. The best results will only be obtained by close co-operation between mining and maintenance departments right from the initial planning stages.

Jan 1, 1977

By W. E. Lockley

This paper will attempt to answer a number of questions which are important to the safe and continued operation of an electric power system. 1. WHY should electrical protective devices be tested? 2. WHAT devices should be tested ? 3. WHEN should they be tested ? 4. HOW should they be tested? 5. WHO should test them ?

Jan 1, 1977

Engineering availability of the 120/200 tonne Wabco haulpak fleet at Mt. Whaleback was in the mid fifties and unstable. The project to achieve a reliable 66% during 1980 highlighted "plannable" maintenance, short cycle scheduling, condition monitoring, backlog control, and, above all, the importance of involving all affected people. It is not sufficient for consultants to design systems and make them work. The people who use the system must understand it, support it and "own" it. In this way, they will develop it and improve results after the outside help has been withdrawn INTRODUCTION In early 1979, PA proposed a programme to improve engineering availability of the Mt. Newman Mining fleet of 70 Wabco haulpak trucks of which 53 were 120 tonne and 17 were 200 tonne units. (Subsequently five 200 tonne trucks from Hamersley Iron were added to the fleet). The ore truck workshop was also responsible for 75 tonne trucks used as water trucks and general purpose vehicles. The need for action was clear. The fleet was achieving availability in the "mid fifties" with wide variations indicating that the fleet was becoming unreliable. Projected tonnages required a reliable 66% availability to be

Jan 1, 1982

By Mark L. Munsell

In recent years, miners have tried many approaches to maintenance such as: - Highly sophisticated computerized programs. - large planning groups designed to preplan and schedule work. - Contract maintenance. - Break down maintenance. Each of these approaches has faced the added constraints: - High replacement cost of equipment necessitating longer useful equipment life - management?s increased scrutiny of all indirect costs such as maintenance. Faced with these factors, what system of maintenance control is right? After visiting many properties recently, it appears there is no right system. Maintenance programs need to be tailored to the people and production constraints that occur at an individual property.

Jan 1, 1976

By Leslie McHattie, Sadek E. EI-Alfy

"The Maintenance Engineering Department at Carol Mining and Concentrating is currently in the process of introducing reliability concepts such as failure analysis, rework elimination, predictive maintenance, computerized maintenance history analysis, etc. to improve the over-all maintenance function in the mine and concentratormaintenance areas. Some current initiatives include:• Implementation ofan infrared thermographic scanning program.• Ultrasonic inspection of shafts for all critical equipment in the mine and concentrator areas.• Non-destructive testing of all major welds done by maintenance personnel.• Development of an effective vibration monitoring and analysis program for the production equipment in the mine (shovels, drills, haulage trucks, locomotives).• Failure analysis performed by maintenance engineers to identify the root cause of component failures on critical production equipment.• Computerized breakdown analysis to identify the recurring component failures which contribute significantly to high maintenance costs and production loss.• Implementation of a computerized maintenance management information system.This paper will outline the planned implementation ofthese initiatives, and others, and will also cover the status and results obtained to date."

Jan 1, 1992

By Paul D. Tomlingson

A new sense of urgency permeates the mining industry concerning maintenance. Mining's continuous process environment demands around-the-clock maintenance support. And profitability conscious mining operations require that production targets be met on time - and economically. These goals require nothing less than an effective maintenance program. In turn, the effectiveness of the maintenance program depends on quality information: easily procured, complete, timely, accurate, and properly used. Information picture is changing Some of the fully integrated, mainframe maintenance information pro¬grams of better days remain. Their upkeep and cost of operation, though, is becoming more difficult to justify. Some operations, faced with production cutbacks a few years ago, downscaled and found they liked it. Now, during an upswing, these operations question the need for the more elaborate, administrative-heavy programs they used to operate. Package programs are not taking their place. Too often, the packages are vague and generic. Some vendors claim that if their offerings work in a hospital complex, they must work in an underground mine. That is not so. Maintenance information in the mining industry is different. The situation has changed There are now smaller, self-contained maintenance groups whose information needs are different. These include an electrical crew in a smelter, an underground mobile equipment shop, or a remote service shop between several distant operating pits. These working environments have changed the character of the information needed as well as the methods for obtaining and using it. Operations-maintenance link In coming back from a downturn, operations people realize that their ability to meet production targets hinges on reliable equipment and avoidance of downtime. They have become familiar with the need to use maintenance services effectively. They also want quality maintenance information. When coupled with the sense of urgency about maintenance, a business-like working environment emerges that has significant new differences in both work control and information. Work control impact Work control has been streamlined to improve communications. Supporting information has been streamlined as well. • Verbal orders are the rule rather than the exception to quickly bring a multi-craft crew to the flotation section or a pit crew to a disabled haulage truck. • Written work requests and work order forms are seldom used, or even needed. Rather, electronic work control logs permit operations to request work, maintenance to acknowledge it, get ready, and do it - quickly, without delay. • Routine servicing is triggered by operating hour accumulation (mobile equipment) or tons of throughput (fixed equipment). Operations is now taking the initiative in delivering mobile equip¬ment to the "bad order line," or switching to a bypass conveyor. Operations wants immediate follow-up reports on equipment condition.

Jan 1, 1989

By Paul D. Tomlingson

Modern production equipment has been designed with greater productive capacity and higher reliability to meet the rigorous operating demands of the mining industry. These improvements have also made the equipment more complex and challenging to maintain. Whether these equipment enhancements contribute to more effective mining operations depends on the overall quality of maintenance. Maintenance is not a stand-alone activity. Although its quality depends primarily on maintenance, cooperation and support from other departments, coupled with the skillful guidance of mining managers, greatly influence maintenance success. Therefore, maintenance risk management must look beyond maintenance itself. Successful maintenance risk management begins with an assessment of the maintenance-related interactions of all mining departments within the mine’s stated operating strategy.

Jan 1, 2005

By Grant J. Goddard

"The Iron Ore Company of Canada (IOC) has been in operation for over 30 years. Today, and in the future, technology and its application will play an ever more critical role in the company’s business success.The Carol Mining and Concentrating (CMC) division of IOC is energetically applying technology today to enhance performance and results, and is aggressively exploring opportunities to apply technology to support improved business results in the future.A critical area of focus is the application of technology to maintenance management performance. CMC has taken a “back to basics” approach to the fundamentals of maintenance management in 1995 and 1996. In parallel, the mine is aggressively implementing its Vision 2000 maintenance integration plan. This plan is targeted at levering the energies applied to sound maintenance management fundamentals as the company moves to a fully condition based maintenance approach.This paper discusses some of the strategies, key technologies and objectives of theVision 2000 maintenance integration plan at the mining operations of IOC."

Jan 1, 1996

By A. J. Stapleton

"The Copper Mountain mine of Gaspe Copper Mines, Limited was brought into production in January, 1968.This paper describes the organization, scheduling and control of maintenance of large open-pit equipment, including 8-cu.yd shovels and 85-ton electric-wheel haulage units. The facilities for repair as well as maintenance are also described, including repair shops and field repair equipment. Maintenance costs are discussed and particular reference is made to tire inspection, records and costs."

Jan 1, 1969

By Ray H. Hario

Background of Erie Mining Company Erie Mining Company, managed by Pickands Mather & Co., is one of the largest producers of iron ore pellets in the United States. The plant is located at Hoyt Lakes, Minnesota, sixty-five miles north of Duluth on the eastern end of the Mesabi Range. Taconite Harbor, situated on the north shore of Lake Superior, is the location of its Power Plant and shipping facilities. (Figure 1) Even though the plant commenced operation in September, 1957, its true be-ginning can be traced back to 1931 when Pickands Mather, in conjunction with Bethlehem Steel Corporation and Youngstown Sheet and Tube Company, began investi-gating the possibilities of processing low grade ores. In 1940, Erie Mining , Company was formed. During the early and middle 1940's, laboratory and pilot plant research was proven to a point where a preliminary plant was deemed feasible and built in 1948. This plant had an annual capacity of 203,200 t (200,000 long tons) per year and, until mid-1952, was the only taconite plant in existence using commercial-size equipment. During this period, ownership of Erie Mining Company was expanded to include Interlake, Inc. and The Steel Company of Canada, Limited. In 1953, authorization was obtained from the owners to build a 7.62 M t (7.5 M long tons) per year plant at a cost in excess of $300,000,000.

Jan 1, 1977

By A. Durnan

Barrick Goldstrike Mines Inc. (Goldstrike) operates a six circuit (train) pressure oxidation plant for the pretreatment of gold bearing sulfide ores. The property is located 27 miles north of Carlin, Nevada. Since the commissioning and start-up of the first circuit in 1990 until the present total plant availabilities have exceeded 90%. The discussion that follows will detail the maintenance practices employed to consistently achieve this goal.

Jan 1, 1994