Search Documents

By H. L. Hartman

The estimation of the magnitude of pressure changes which occur in mine ventilation circuits is of primary importance to the mining engineer in making changes in an existing mine or in projecting the ventilation requirements of a new mine. It is a formidable task in many cases, because no adequate theory is available and empirical data are unreliable or even lacking. The common practice of increasing one's estimate of the mine static pressure by an arbitrary "safety factor" to compensate for the unknown is a poor substitute for accuracy. Generally little difficulty is encountered in calculating friction losses in mine airways. As long as the friction factor can be reliably estimated, the well-known Atkinson formula gives accurate results. However, it is in the determination of shock losses that the ventilation engineer encounters difficulty and is apt to resort to an arbitrary allowance. Shock losses may constitute as little as five or as much as twenty-five percent or more of the overall pressure drop in the mine, and such allowances are generally completely unsatisfactory. Since other shock losses have been covered by McElroy (1), this paper deals with a long-neglected source of shock and pressure change in ventilation circuits, divergence and convergence of airflows, here referred to by their more common mining terms, splits and junctions. PREVIOUS WORK There is practically no fundamental information available in ventilation literature on the splitting and junction of airflows, either in mining or mechanical engineering periodicals or handbooks. Fluid mechanics textbooks seemingly avoid the subject of divergence and convergence, except for brief empirical treatment. The only investigation reported for mine ventilation systems was by Weeks, et a1 (21), in 1933. Although applicable to the case of line brattices in coal mines, it cannot be applied to the general case of mine splitting and junctions involving change of direction with little or no area change. In dealing briefly with the subject of shock losses at splits and junctions, McElroy (1) suggests only that they be considered comparable to bends, with losses at junctions being increased 50 pct to allow for interference of merging streams. He recognizes the importance of quantity ratio but concludes that exact quantitative data are lacking to compute losses at splits and junctions. A very capable summary and analysis of the state of knowledge in industrial ventilation and fluid mechanics regarding losses due to divergence has recently been reported by Gilman (3). In considering all earlier work dealing with both air and water as fluids, he compares results on a common basis and obtains good empirical agreement. For divergent flow, the controlling variable in each branch is the quantity ratio, although the deflection angle is of secondary importance. Empirical equations are presented for straight and 90-deg branches with varying velocity ratios, assuming branches smaller than the main duct. These formulas are modifications of the Borda equation for abrupt contraction and expansion. The only information available on shock losses in convergent flow are approximate experimental data presented by Alden (4) and the Manual of Recommended Practice for Industrial Ventilation of the American Conference of Governmental Industrial Hygienists. Alden considers the effects of both quantity ratio and deflection angle. The data indicate an effect opposite to that observed in divergence, the shock loss varying directly with quantity ratio. SHOCK LOSS THEORY Because pressure losses due to shock have been found to bear a constant relation to the mean velocity of flow in a given conduit, they are frequently expressed as a dimensionless function of the velocity head, termed the shock loss factor. For airflow in ducts and mine airways, the shock loss may be represented by the formula (1): Hx - XHv, (1)

Jan 1, 1961

By George B. Clark

Many basic engineering principles of all four phases of mining operations, namely, prospecting, exploration, development, and exploitation, can be analyzed better in terms of quantitative geology. Geological data from both field and laboratory will also complement scientific methods now being developed. THE geological data emphasized so successfully in prospecting for new deposits, that is, structural controls, strength of solutions, and type of mineralization, are basically those required for successful exploitation. In the mining of newly discovered deposits the most economical methods should be employed as early as possible to keep the overall cost per unit produced at a minimum and to permit maximum extraction of valuable minerals. A crucial question is: How can geological data be translated into useful quantitative results which will aid in achieving this end? H. E. McKinistry' has suggested that a solution may be reached in one of two ways: 1—the usual approach, use of judgment based on experience; or 2—mathematical calculations and tests on models, both subject to certain limitations. He also suggests that in addition to better use of geology more case data and theoretical data are needed on which to base sound judgment. Further research, therefore, is necessary. Perhaps in this field the emphasis should be on more specialization in mining methods and ground movement by men with thorough training in physics, engineering, geology, and underground mining. These specialists would be equipped to point out the most economical and scientific methods of exploitation. Selection of a stoping method is governed by the amount and type of support a deposit will require in the process of being mined, or by the possibility of employing the structure of the deposit to advantage in mining the ore by a caving method. In addition to these factors there are others which almost invariably influence the choice of an economical method of mining:' 1—strength of ore and wall rocks; 2—shape, horizontal area, volume, and regularity of the boundaries of the orebody, and thickness, dip and/or pitch of the deposit and individual ore shoots; 3—grade, distribution of minerals, and continuity of the ore within the boundaries of the deposit; 4—depth below surface and nature of the capping or overburden: and 5—position of the de- posit relative to surface improvements, drainage, and other mine openings. In the final analysis it is usually necessary to disregard the less important of these factors to satisfy the requirements of the more important. Because of the variation of geological conditions throughout and surrounding the deposit, no mining method will be everywhere ideally applicable to the conditions encountered in one ore deposit. The immediate problem is to interpret the above physical characteristics of deposits in terms of geological characteristics. Very few quantitative geological data are available on the factors related to a choice of mining methods. However, there are many descriptive data in mining and geological literature which collectively show how important an effect details of geology have upon all phases of mining operations. The following categories of basic mining methods were investigated to establish the geological factors that have affected their successful application: 1— open stopes with pillars; 2—sublevel stoping; 3— shrinkage stoping; 4—cut-and-fill stoping; 5— square-set mining; 6—top slicing and sublevel caving; and 7—block caving. It should be noted that the first five of these methods are listed in the order of increasing support requirements. Mines were selected as examples only where geological descriptions were complete enough to warrant their use. A study of the geological factors involved in mining operations led to a choice of the following classifications, employed in Table I: 1—structural type of orebody; 2—dimensions (geometry); 3— country rock (type); 4—faulting, folding, and fracturing; 5—alteration of ore and rock; 6—type of mineralization; and 7—geological factors determining mining method (summary). Of these factors only one yielded results that can be defined from available data in a quantitative manner, i.e., dimensions of the deposit. These are the most reliable guides that can be used in selection of suitable mining methods. They are, in general, the properties of geologic structure most difficult to evaluate by studies of models, pho-toelastic studies, and other laboratory methods, all of which are at present more limited in their applications than the geologic method. Application of geology has proved a reliable guide in other phases

Jan 1, 1955

By E. B. Burwell, R. H. Nesbitt

Designed by army engineers, the NX borehole camera provides the most economical method of subsurface exploration so far devised. Continuous cylindrical color photographs now reveal minor flaws in foundation bedrock not always disclosed by borehole samples. A unique projector transforms the photographs into true-to-scale images of three dimensions. ANEW milestone in the progress of photography and subsurface exploration was reached when the Chief of Army Engineers announced the development of the NX borehole camera. In obtaining continuous undistorted cylindrical color pictures of dry or water-filled borings the device surpasses all other cameras designed for photographing interior surfaces of pipes, wells, and conduits. The usefulness of the camera and the unique projector that comes with it are at once apparent. To the geological, mining, and civil engineer alike it signifies the end of guesswork with respect to underground conditions that have eluded identification by conventional core-drilling methods. To the medical profession it may well signal new progress in photo optics which could result in cylindrical color photographs supplementing the X-ray and existing photographic methods used in exploratory surgery. The pilot model of the camera has more than paid for itself as a result of its success in bringing to the surface at two dams information previously obtainable only by costly drilling of mansized boreholes for subsurface on-the-spot examination. Such bores cost as much as $200 per lineal foot as against $10 per ft for the conventional 3-in. or NX exploratory core borings from which the present invention derives its name. The NX camera can now photograph completely the interior surface of these borings. Research and development for the first camera and projection equipment were conducted by Engineering Research Associates, Division of Remington Rand, Inc., under the technical supervision of the Geology and Geophysics Branch, Office of the Chief of Army Engineers in Washington, in accordance with plans and specifications furnished by this branch. Subsequent modifications of the camera-lowering device, transporting equipment, and special field tools were made in the Corps of Engineers' Ohio River Division Laboratories in Cincinnati. The background of this development is interesting. Among the more difficult foundation problems involved in construction of concrete dams are those resulting from bedrock imperfections that escape disclosure by conventional exploration methods. Often these imperfections are of sufficient magnitude to introduce costly changes, especially when their presence is discovered only after foundation excavation is well in progress. Bedrock flaws most frequently camouflaged may be ruptures resulting from the enormous stresses to which rocks have been subjected, or they may be planes or zones of weakness related to chemical alteration and underground erosion. Obviously, detailed information on their location, dimensions, and structure is important, as these factors can affect the stability of a dam and the security of life and property downstream. Their discovery and appraisal entail extensive subsurface exploration. At present the most economical exploratory tool available to geologists and engineers is the small-diameter diamond core drill by means of which cores of the foundation bedrock are recovered for examination and testing. All too often, however, these samples fail to disclose minor foundation flaws that may be of major importance before a structure is completed. As a result, the small-diameter drillings are supplemented generally by more reliable but much more costly shafts, tunnels, or large-diameter calyx drill holes that permit the investigator to examine the foundation rocks in place. It was to reduce the number and cost of these expensive and time-consuming investigations, as well as to obtain more complete information on rock structure from the smaller borings, that the NX borehole camera was developed. That it has been eminently satisfactory in accomplishing that purpose is demonstrated by its success most recently at the Folsom dam, under construction on the American River, 23

Jan 1, 1955

By H. J. Gerritsen

From presently available components a portable, rugged, reliable apparatus can be built which will be able to detect methane concentrations of 0.1% and lower in air. Sensitivity and design considerations of the apparatus are given. Ways to build even simpler and cheaper apparatus in the future are indicated. Traditionally the problem of detecting and monitoring the presence of dangerous gases present in small concentrations in air has been a difficult one. Whether canaries,' or sophisticated chemical or thermal conductivity methods are used, they seem to be either slow, cumbersome, or otherwise not completely satis factory. A seemingly natural way of gas detection is to measure the strength of absorption undergone by light of a wavelength that the gas to be detected absorbs. This method has been difficult to apply in view of the low power output over a narrow wavelength range in the infrared from traditional glow bar light sources. Besides, the apparatus to select such a narrow band of wavelengths is quite costly and complex. The use of a laser solves these problems simultaneously. Although a variety of lasers are available to detect a variety of gases (such as carbon monoxide or methane) whose early detection would be desirable, this paper deals exclusively with the use of lasers for methane detection. ABSORPTION SPECTRUM OF METHANE IN AIR The absorption spectrum of pure methane is very well known.2-4 There are four fundamental vibrations, all occurring in the infrared of which only two absorb strongly. They occur at 3.3 µ and 7.7 µ. The absorption spectrum is quite complicated due to the fact that the methane molecule can rotate in a variety of rotational quantum states. These rotational states are furthermore split by anharmonic forces such as the Coriolis force.4 When methane is present in air at atmospheric pressure, much of the very fine structure due to the anharmonic force is washed out since the pressure broadening is of the same magnitude as the splitting due to anharmonicity. For most of the spectrum at 3.3 µ, the rotational lines are typically separated by 0.01µ while the individual linewidth is 0.0001 µ. It is thus very important that the laser emit at a wavelength that coincides with one of these rotational lines. Before elaborating on the point that such a laser exists and how it performs, it is necessary for later discussion to point out that in the

Jan 1, 1967

By K Rau

The overall success of a mining operation is directly impacted by the reliability and availability of mining equipment. Heavy-duty vehicles such as excavators and haul trucks are used for conveying of bulk material and improving such assets’ availability helps reduce costs, increase throughputs and improve safety (Ravande, 2022). If a mining operation’s key performance indicators (KPIs) are tied to operational performance, then overall equipment effectiveness (OEE) is an essential metric to track progress and to identify areas of improvement.

Sep 1, 2024

By W. R. Sharp

The ability to target, delineate, excavate, and produce local resources is essential to the establishment of man's long-term presence in space. Many procedures and equipment utilized to mine resources here on Earth may be directly applicable on the lunar surface, while others may need extensive redefinition and development. This paper compares, for a lunar base, the alternative of burrowing into and below the lunar surface with that of surface mining. A conceptual underground mechanical excavator is presented.

Jan 1, 1991

By O. T. Berge

Development and production from open cut mines continued its vigorous growth trend during the year 1968. Material handling and transportation were again exposed to the use of larger equipment with shovels, trucks and front end loaders leading the way. Highlights of World Mining Activities Africa: The Anglo American Corp. opened a new high-grade copper mine in Zambia during the year. In Angola, the Companhia Minera do Lobita planned a 3 million ton iron ore production for 1968 from new mines which will ultimately produce 5 million tons per year. A feasibility study of Bethlehem Steel Co., for the development of large high- grade iron ore reserves in Gabon, was in final stages of completion this year and Pickands Mather and Co. continued its investigation of iron ore deposits along the Ivory Coast.

Jan 2, 1969

By J. S. Chung

As part of ongoing deep-ocean mining research, hydraulic transport systems as well as status of deep-ocean mining systems are reviewed in the aspects of manganese nodules and crusts from 800-6,000-m depth. The emphasis of the investigation of hydraulic transport is placed on the shape effect of particles on the pressure gradients and flowrates. Series of tests are being conducted to study the lift characteristics of a 2-phase vertically upward hydraulic transport of 2 types of small solid particles in a PVC pipe of 1-in (2.54 cm) diameter: irregular-shaped silica sands and equivalent spherical glass beads. Pressure drops and mass as well as volumetric flow rates were measured by electromagnetic (EM) flowmeter and mass flowmeter. The particle sizes used are 8-10 mesh. The results in turbulent flow range of 104 < Re < 105 show that pressure gradients or friction factors are smaller for the spherical beads than the sands. The larger the concentration of the particles are, the larger the pressure gradients become. The larger the particle concentration is, the less the effect of particle shape on pressure gradients becomes. The shape effect is greater for the minimum particle transport velocities than for the settling velocities.

Jan 1, 1999

By Jonathan Peck, Jim Gray

"While the mine developer looks for bigger and better orebodies in countries offering lower risks to development capital, the opera-tor of existing mines is looking for bigger and better ways to use his existing resources. Mining operations today utilize a variety of stand-alone systems for planning and managing their operations. In both small and large mines, payroll, accounting, inventory, planning, and engineering requirements are met using a combination of manual and computer-based systems.Technical advances and new enabling technologies are changing how mines are doing business. PC-based systems are allowing small operations to join the larger mines in using advanced computer-based systems. Advanced monitors are being used in maintenance to track, predict and correct the health of production equipment. Production monitoring systems are used to measure the performance of operating equipment and personnel in real time. This detailed information on how much, where, when, and by whom is being used for proactive management and planning. Ultimately, this information can be used to optimize and control the machines’ activities, eventually leading to robotic and autonomous operation of mining equipment.As the use of technology increases in mining, specific information objectives are being met but other problems are being created. The life cycle of technology is small, and as current systems are replaced by newer ones, integration problems and additional end-user training are created. In addition, onboard monitoring systems can create large volumes of data, data which are frequently archived without being analyzed. Mine operators are also duplicating efforts applying new technologies in an effort to be more competitive, but in doing so are creating interfaces which are only compatible with their own facilities. As system development moved from the centralized mainframe computer to the PC environment, the fragmentation of these systems became more pronounced.To efficiently continue in adapting and utilizing advancing technology, the mining industry needs to develop a system architecture that readily integrates as many sub-systems as possible. This will provide a framework for existing system integration and design guide-lines for future development. The Total Mining System (TMS) concept will allow a network of stand-alone functional modules to be readily integrated with minimal effort. This paper will discuss some of the current technologies cur-rently in use in some surface mine operations.In addition, a description of the information system and communications requirements that will be needed to integrate these components in the future, will be discussed."

Jan 1, 1996

By J. F. Myers

A bit of old philosophy: The optimist, the pessimist, The difference is droll; The optimist, the doughnut sees, The pessimist, the hole. This is a neat summation of the viewpoint of those engaged in "treating the crude mineral crust of the earth." Many of those in high places have reminded us during the year of the diminishing supply of the resources so essen-

Jan 1, 1948

By Clyde E. Williams, V. N. Krivobok, C. H. Herty

THE extreme effect of the depression on the steel industry is well illustrated by the fact that the amount of iron ore shipped from the Lake Superior district was the lowest in 47 years. Something over 3 1/2 million tons of ore was shipped in 1932, compared with over 65 million tons in 1929. It is not surprising then that practically no advancement in iron ore beneficiation has been made. Improved research and development work, however, was continued at the Michigan College of Mines in the survey of the lean iron ores of Michigan with reference to the possibility of their concentration; at the University of Minnesota in its large-scale jigging studies of Lake :Superior ores; and at Battelle Memorial Institute in the development of improved jigging of iron ores. The successful operation of the new Hadsel mill at a gold property in California gave such low grinding costs on a quartz ore as to give much encouragement in the iron ore industry for a cheapening of the cost of grinding lean ores for concentration.

Jan 1, 1933

By H. W. Gillett

MAINTENANCE of membership by the technical so¬cieties and the activity of these societies in spite of the adverse business situation have been noteworthy. This forcibly brings home the fact that industry recognizes that sound technical guidance is well worth its cost. The numerous difficulties and losses due to defects of various kinds arising from gas-metal reactions are now generally recognized and interest in these problems is widespread. The forthcoming A. I. M. E. round-table discussion of gas-metal problems will do much to clarify the situation and will permit us to assay our present knowledge and to suggest the proper direction for profitable future research. "The Age Hardening of Metal" was the title of the annual I. M. D. lecture delivered by Dr. Paul D. Merica. A critical review of the known facts relating to age-hardening phenomena was first given, followed by the presentation of a theory correlating the detailed observations which have been made regarding the mechanism of the hardening.

Jan 1, 1933

By H. J. Wasson

WITH the close of 1932 and the third year of the depression, the activity of oil production presents, amidst the general wreckage and chaos of industrial society, a somewhat unique picture of rationalized economic effort. East Texas still dominates the contemporary horizon, but it has become, at least for the time being, a definitely known factor. With its 9500 wells it is approximately 90 per cent drilled up. So long as production control obtains, it is merely one important factor of the national oil reserve. Each succeeding month of stabilized production tends to lull the industry&apos;s fears and the menace, both actual and psychological, of this giant field becomes ever more remote.

Jan 1, 1933

"INTRODUCTION In recent years, there has been increasing focus on environmental and social impacts of the extractive industries, climate change and resource scarcity. The concept of the circular economy aims to replaces the “take-make-dispose” economic model with one that eliminates waste of all kinds and is restorative by design. Such closed-loop systems implicitly aim to reduce the quantity of primary extracted materials entering the economy, thereby affecting supply and demand dynamics, hence mining industry economics. For the metals industry, the ability to engage in, or adapt to the circular economy can be heavily affected by industry structure and geographical factors. Eco-efficiency initiatives that reduce waste and environmental impact may help the mining and metals industry align with some of the goals of the circular economy. This paper focuses on base metals, and explores case studies in copper, lead and zinc. It analyzes primary and secondary metal production, and recycling. It examines company structures and how these affect engagement with the circular economy. CIRCULAR ECONOMY PRINCIPLES Ellen MacArthur Foundation (2012) describes the circular economy as “an industrial system that is restorative or regenerative by intention and design”, which “replaces the ‘end-of-life’ concept with restoration”, and “aims for the elimination of waste through the superior design of materials, products, systems, and, within this, business models”. The concept is systems focused. For materials such as metals, a series of loops are considered, including maintenance of devices, reuse, refurbishment and recycling. Potential methodologies to achieve circular economy outcomes include disassembly and reassembly of manufactured goods, leasing rather than buying major appliances, and converting to renewable energy sources. The circular economy is partially aligned with the principles of eco-efficiency, which relate to reducing the environmental impact per unit of a material produced. PRIMARY AND SECONDARY METAL PRODUCTION Base metals (copper, lead, zinc and nickel) are essential ingredients in modern economies and are key commodities produced by the global mining industry. Metal production can be categorized as primary or secondary. Primary metal comes from the processing, smelting and refining of metal content extracted from ores, while secondary production comes from metals recovered from recycled streams (e.g. recycled lead-acid batteries, copper wire scrap, etc.). Metals are stored in natural, anthropogenic in-use and anthropogenic waste stocks. An example of the stocks, flows and processes associated with global copper extraction and use is shown in Figure 1."

Jan 1, 2018

By JAMES BRADLEY

THE Spanish mine is in Nevada County, California, 21 miles northeast of Nevada City by road, and 3 miles north of the town of Washington. The mill and surface buildings are on Poorman&apos;s Creek at an ele¬vation of 3,000 ft. About 35 men are employed at the property, which is producing 50 tons of ore per day. Electric power, purchased from the Pacific Gas and Electric Co., is brought in from Alleghany, seven miles away. In the early days the mine was operated by F. W. and P. R. Bradley. Between 1883 and 1899 the production was approximately $900,0)0 in gold. The ore treated during; that time yielded an average of 60 cents per ton and was mined and milled at a profit. The surface, oxidized, ore deposit was 30 to 100 ft. wide and was mined by the glory-hole method. The milling-plant at first consisted of a Blake crusher an-1 a small Huntington mill; later three large Huntington mills were added to the plant. In 1893 a new mill was built at a lower adit- It consisted of 10 stamps and four Huntington mills. The gold was secured by amalgamation, the recovery being about 50 per rent.

Jan 1, 1931

By David M. Rubio

The Ortiz Mine is an open pit-heap leach gold operation in central New Mexico processing about 3,100 tonnes (3,400 short tons) per day. It is the initial mining property in the United States developed by Gold Fields Mining Corporation, a subsidiary of Consolidated Gold Fields, PLC. This paper discusses the evolution of the present mining and ore control procedures as adaptions to the characteristics of both the rock being mined and the orebody, and with respect to the fact that mining is done by a contractor.

Jan 1, 1984

By George D. Dub

The Bureau of Mines, in connection with the investigations of war minerals it conducted, examined the graphite deposits of this country, studied the methods of mining and preparation used, and sought to devise more efficient methods for the preparation of domestic graphite, and to standardize the quality of the product. The graphite investigations covered three general phases, as follows: 1. An examination of the deposits in Alabama and other States, and a survey of the methods of mining and preparation used. In this connection methods of sampling and analysis were noted and experiments made to determine a standard method of sampling and a, rapid but accurate method of analysis. 2. Experimental work on the concentration and refining of domestic crucible graphite to improve the quality of the product and to lessen waste. 3. Experimental work in crucible manufacture to determine the properties of domestic flake and the maximum proportions that might be used without impairing the quality of the crucibles. This work was accompanied by photomicrographic study of crucible structure.

Jan 1, 1920

Mineral exploration and development can have a significant impact on the environment and local communities, in some circumstances extending well beyond the mine site. Poor environmental performance and consequent social impacts by some companies have affected the reputation of the whole industry to the extent that the principal public concern about mining is its impact on the environment. This is consistent with public attitudes about other major natural resource sectors such as forestry and commercial fishing. Traditionally the community has relied on governments to set the benchmark for acceptable environmental and social performance through establishing and revising regulations governing the mining industry. This however assumes that regulations keep pace with community expectations. It also does not take into account those circumstances where governments can have conflicting roles as both watchdog and project partner. Government regulations and industry self-regulation are not in of themselves sufficient for the minerals sector to demonstrate that it has adequately addressed environmental and social issues associated with the sector. For the minerals sector to improve its reputation it must first improve its environmental and social performance. To do this requires the sector to operate to acceptable standards of environmental and social performance and for the sector to be able to credibly communicate this to its stakeholders such as investors, non-government organisations (NGOs), customers, staff, regulators and local communities. Independent third party certification of environmental and social performance (æcertificationÆ), already operational in forest and fisheries management, is proposed as a mechanism to enable the minerals sector to achieve this. World Wide Fund for Nature (WWF) and industry partners will be collaborating in a project to ascertain the applicability of æcertificationÆ to the minerals sector. A number of economic, social and environmental benefits are identified that could accrue should mining companies be able to differentiate themselves on the basis of environmental and social performance, an attribute evident in æcertificationÆ schemes. External audiences are seeking increasing levels of information and data on environmental and social performance of mining companies, be it local communities, investors, financial institutions or NGOs. Environmental and social reporting should be a key communications device that stakeholders can rely on as a reliable, credible source of information on environmental and social performance. WWFÆs contribution to the debate about environmental and social reporting has been to develop a process to assess the quality of environmental and social reports against reporting ingredients which WWF believe are important if a report is to be an accurate reflection of the reporting entitiesÆ environmental and social performance.

Jan 1, 2002

By I. Dumitrescu

Since 1990, the entire Romanian mining industry has suffered a major restructuring, i.e. technical and economic. The large majority of the remaining active mines are these with a chance for economic comeback. This is also the case for the mines that belong to MINVEST Deva Company; most of the mines are closed, and are waiting to be reclaimed. The authors present the closing procedures of the former copper mining perimeters managed by MINVEST. It is well known that pollutants of concern for the environment must be monitored to obtain reliable information on the quality of ambient conditions and to minimize their impact on the environment. Consequently, the monitoring problems during the closing procedures will be presented.

Jan 1, 2008

By Henderson, Robert

A GOOD idea of the magnitude of the underground operations at Climax can be gained from the following figures. A little more than 43,000,000 tons has been drawn from the mine and of this amount, 40,500,000 tons has been drawn in the past ten years and 12,000,000 tons was drawn in two of the war years. The maximum daily average output over a period of one month was slightly more than 20,000 tons but during this period, production on certain days was 24,000 tons, and 9000 tons was produced in a single eight-hour shift. This production came chiefly from 260 draw points although all of them were never in operation at one time. The haulage system for these draw points is made up of 7.5 miles of 36-in.-gauge track, and 131,000 ft. of subsidiary drifts and 44,000 ft. of raises have been driven to develop the necessary broken ore reserves for this high production. Power consumption is often considered an index of operating efficiency. In 1943, the year of maximum production, the mine power consumption was 19,223,000 kw.-hr. or 3 kw.-hr. per ton; in 1945 it was 3.5 kw.-hr. per ton. To handle this amount of power, there are four transformer stations and one switch station in the mine. Mr. Garrabrant, the chief electrician, describes the electrical installation in this issue.

Jan 1, 1946